Construction of Block Elementary Education Office (BEEO) Jai Devi Tehsil Sundernagar Distt. Mandi (HP) (SH-C/o Building Portion including W/S and S/I and Septic Tank)

Amount

Excavation in foundation ,Trenches etc in earth work in all kind of soil such as pick work, jumper work, blasting work in soft and hard rock conglomrate rock or saturated soil including chiselling / wedging out rocks (where blasting is prohibited) and pumping or bailing out watering/ dewatering upto any lift, stacking the excavated soil upto any lead from the edge of excavation and then returning the stacked soil in layers, when required into plinths,sides of foundations etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth with in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing form work with steel plates 3.15mm (three point fifteen milimeter) thick welded with angle iron frames 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centering,shuttering,strutting and proping etc. with wooden battens and ballies heights of propin and centering below supporting floor to ceilling in all heights and removel of the same for in-situ reinforced concrete and plain concrete work including carriage of materials with in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

(a) Foundations footing,bases of columns and the like and mass concrete.

(b) Flat surfaces such as soffits of suspended floors,roofs,landings and the like Floors,etc.upto any thickness.

(c) Columns pillars, posts, and struts square,rectuangular of polygonal in plan.

(d) Staircases with slopping or stepped soffits includding risers and stringers excluding landing.

(e) Beams , cantilevers, girders and lintels sides and soffits of bems, beam haunchingcantilivers, girders, bressumers and lintels upto any in depth. &upto all heights from floors.

Edges of slabs and breaks in floors and walls: Under 20 cm. wide.

Providing and laying cement concrete 1:3:6 (1 cement:3 sand:6 graded stone aggregate 40mm nominal size) excluding cost of centring and shuttering in Foundations and plinthincluding carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and laying cement concrete 1:6:12(1Cement:6Sand:12graded stone aggregate 40mm nominal size) in Foundatio & Plinth complete with in all respect.including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and laying cement concrete 1:4:8 (1 cement : 4 sand : 8 Graded stone aggregate 25mm nominal size) and curing complete excluding cost of form work in foundation and plinth in breast and retaining walls etc. complete with in all respect.including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and laying mechanically mixed and vibarted cement conrete machine batched,machine mixed and machine vibrated design mix.cement concrete of M-25 grade for reinforced cement concrete structural elements,excluding cost of centering /shuttering,finishing and reinforcement work including curing & carriage of material in all leads and lifts. stone aggregate 20mm nominal size. complete with in all respect.including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

(a) Foundation , footing, basis of columns and mass concrete.

(b) Suspended floors , roofs, landing , shelves and their supports , balconies,centilevers slabs in all hights & all floor level

(b) Columns pillars posts and struts upto all floor levels.

(d) Stair cases (except spiral stair cases) excluding landing but including preparing of the surface and finishing of nosing upto all floor level.

Providing and laying damp proof course 38 mm (thirty eight millimetre) thick with cement concrete 1:2:4 (one cement :two sand :four stone aggregate 12.5 mm (twelve point five millimetre) nominal size) and curing complete as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Applying a coat of hot bitumen (mexphalt 80/100 (eighty/hundred) or equivalent) using 1.70 Kg. (one point seven zero kilo gram) per square meter on damp proof course after cleaning the surface with a piece of cloth lightly soaked with kerosene oil as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing Tor steel reinforcement for R.C.C. work including bending, binding and placing in position including cost of binding wire complete upto floor all level : including carriage of materials with in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Brick work using common burnt clay building brick in foundation and plinth in Cement mortor 1:6 (one cement : six sand) 2nd class brick complete with in all respect.including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Half brick work using common burnt clay building bricks in super-structure above plinth in Cement Mortar 1:6 (one Cement : six Sand) Second Class Bricks including carriage of materials with in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Random rubble masonry/polygonal rubble masonry (uncoursed/brought to courses) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (one cement :six sand : twelve graded stone aggregate 20mm (twenty milimeter) nominal size) at plinth level in Cement Mortar 1:6 (1 cement:6 sand) including carriage of materials with in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Stone work ashlar punched (ordinary work) in superstructure upto floor two level in cement mortar 1:6 (one cement: six sand) including pointing with cement mortar 1:2(1 cement : 2 sand) with in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge

Boulder filling dry hand packed tightly in under floor complete with in all respect.including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing 2nd class deodar wood work in frames of doors,windows,clerestory,windows and other frames wrought,framed and fixed in position with in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge

Providing and fixing 40 mm (forty milimeter) panelled glazed or panelled and glazed shutters in 2nd class deodar wood for doors windows and clerestory windows. Including black enamelled iron butt hinges with in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge

Providing and fixing 40 mm (forty milimeter) thick 2nd class deodar wood wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screw etc with in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge

Providing 40x3 mm flat iron hold fast 40cm. Long including fixing to frame with 10mm diameter bolts & nuts and wooden plugs and embeding in cement concrete block 30x10x15cm. 1:3:6 ( 1 cement : 3 sand: 6 graded stone aggregate 20mm nominal size) with in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge

Providing and fixing 19mm thick Commercial Board water proof shutters for up boards i/c fixing with nickel plated piano hinges with screws etc complete)

Providing and fixing 25mm + 25mm balusters 25mmx25mm (twenty five into twenty five ) square wrought fixed with ends housed (square or splay) to hand rails and treads or strings complete in. 2nd class deodar wood. with in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge

Providing and fixing 75 mm x 60mm (seventy five into sixty ) rounded hand rails in straight length complete in. 2nd class deodar wood. with in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge

Providing and fixing anodized aluminium sliding door bolt anodized colour and shade with bolts and nuts screws etc. complete.300x16mm (three hundred x sixteen millimetre) with in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge

(a) 300 x 16mm. (Three hundred into sixteen milimeter)

(b) 250x16 mm (Two hundred fifty into sixteen milimeter)

Providing and fixing aluminum tower bolts(berrel type) anodized transparent or dyed to required shade and colour with screws etc. complete with in all respect.including carriage of material with in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

(a) 250x10mm (Two hundred fifty into ten milimeter)

(b) 100x10mm (One hundred into ten milimeter)

Providing and fixing aluminum handles anodized transparent of dyed to required colour or shade with necessary screws complete with in all respect.including carriage of material with in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

(a) 125mm (One hundred twenty five milimeter)

(b) 100 mm (One hundred milimeter)

Providing and fixing bright finished brass ball catcher 10 mm (ten milimeter )dia for cup board complete with in all respect.including carriage of material with in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing 65x35mm. (sixty five into thirty five milimeter) special quality bright finished brass cup board locks or wardrobe locks with six levers including necessary screws etc. (Indian make of approved quality).complete with in all respect.including carriage of material with in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing bright finished hard drawn hooks and eyes. 100 mm (One hundred milimeter) with in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge

Providing and fixing oxidized M.S. single acting spring hinges with necessary screws etc.150 mm (one hundred fifty milimeter) complete with in all respect.including carriage of material with in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Kota stone slab flooring 25mm (twenty five milimetre)(average) thick base of cement mortar 1:4 (one cement :four sand) laid over all jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Kota stone slab 25mm (twenty five milimetre)(average) thick in riser of steps,skirting,dedo and pillar laid on 12mm (twelve milimetre) (average)thick cement mortar 1:3 (one cement :three sand)and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying 10mm. (ten milimeter) thick anti skid water proof, stain and impact resistant heavy duty vitrified tiles( Nitco or equivalent) of size upto 600 x 600mm. (six hundred into six hundred milimeter) of specified shade in floors, treads of steps and landing laid on a bed of 12mm. thick cement mortar 1:3(one cement: three sand) jointing with cement slurry mixed with pigment to match the shade of tiles.

Providing and fixing 0.60mm (zero point sixty milimeter) thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with screws prepainted iron J or L hooks, bolts and nuts 6mm diametre with prepainted limpet and rubber washers complete with all accesoriees as required complete with in all respect.including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Steel work welded in built up sections,trusses and framed work, including cutting , hoisting, fixing in position and applying a priming coat of red lead paint. In beams joists channels ,angles , tee ,flats with connecting plates or angle cleats as in main and cross beams,hip and jack rafters,purlins connected to common rafters and the like. complete with in all respect.including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease,dirt and other forein matter sand papering and knotting ready mixed paint with wood priming pink of approved brand and manufacture (Nerolac/Asian Shalimar) conforming to IS: 3536-1966 brushing as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Painting two coats (excluding priming coat) on new wood and wood based surfaces with ready mixed paint brushing to give an even shade including cleaning of oil, grease,dirt and and other foreign matter sand papering and stopingready mixed paint other thanwhite as per direction od Engineer-in-including carriage of materials within all leads, lifts and other incidentals.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

6mm Cement plaster to ceiling (b) In Cement Mortar 1:4(one Cement: four Sand) with in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge

15mm (fifteen milimetre) cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering up to all floor level includingarises, internal rounded angles,chamfers and/or rounded angles not exceeding 80mm(eighty milimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement:six sand)as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals

15mm cement plaster in single coat on fair side of brick/concrete/stone walls for interior plastering upto floor two level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth. Cement mortar(1:3) (1 cement:3 sand). complete with in all respect.including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

White washing with lime on undecorated wall surfaces two coats to give an even shade including throughly brooming the surface to remove all dirt dust mortar dirt and other foreign matter. with in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and Manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth. Priming coat with distemper primer

Providing plinth protection 50mm thick in cement concrete 1:3:6 (one Cement : thee Sand : six Graded stone aggregated 20mm (twenty milimeter) nominal size) Curing complete with in all respect.including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing under layer for plinth protection of 75mm (seventy five milimeter) thick (unconsolidated) bed dry brick/stone aggregated 40mm nominal size with rammed and consolidated and grouted with fine sand including preparation of ground. complete with in all respect. including carriage of material with in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Constructing Course rubble hammer dressed 'U' shape open surface drain with side wall. 15x22 cm in cement mortar 1:6 (one Cement : six Sand) and inside plastring with cement plaster 1:3 (one Cement:thee Sand) including earth work and laying 10 cm cement concrete in 1:5:10 (one Cement : five Sand :ten graded stone aggregate) of 40 mm (forty milimeter ) nominal size) and 7.5 cm (seven point five milimeter) cement concrete 1:2:4 (one Cement : two Sand : four Graded stone aggregate of 20 mm (twenty milimeter ) nominal size) and finished with a floating coat of neat cement complete as per standard design with in all respect.including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing to wall ceilling and floor galvanised mild steel tubes (medium grade) tube fitting and clamps including making good the wall ,ceilling and floor (confirming to be BIS Specification ) complete with in all respect.including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

(a) 15mm nominal size

(b) 20mm nominal size.

Providing and fixing viterous china wash down water closet (European tpye WC pan ) with intergal "P" or "S" Trap including jointing the trap with soil pipe in cement mortar 1:1 (1 Cement 1 sand ) (seat and cover to be measured and paid for sperately ) Anglo Indian (Universal closet ) (confirming to BIS specification ) complete with in all respect.including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing 10.00/12.50/15.00 litres vitreous China low level flushing cistern with a pair of C.I. or mild steel brackets, complete with fitting such as lead valve less syphon, 15mm (Fifteen milimeter) nominal size brass ball valve with polythene float, C.P. Brass handle, unions and couplings for connections with inlet, outlet and overflow pipes, 40mm dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately).including carriage of material in all leads and lifts (confirming to BIS specification) complete with in all respect. including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing vitreous China bowl pattern urinal No. 5001 of jaguar or cera including connection the urinal with waste pipe by means of white lead mixed with chopped hemp (waste pipe to be measured and paid for separately) Flat back type of size 430mm x 260mm x 350mm.(four hundred thirty x two hundred sixty x three hundred fifty millimetre) complete with in all respect.including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing Division Plate for Urinals 600mm x 300.mm (six hundred x three hundred millimetre) Vitreous China complete with in all respect.including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing vitreous China wash basin No. CNS-WHT-807 of size 760 X 500 X210 of Jaguar or its equivelent with single hole for pillar tap with cast iron or mild steel brackets painted white including cutting holes and making good the same but excluding fittings flat back complete with in all respect.including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing vitreous China pedestal for wash basin complete recessed at the back for the reception of pipes and fittings .complete with in all respect.including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing 600mm x 450mm (six hundred into four hundred fifty milimeter ) bevelled edge miror of superior glass mounted on 6 mm (six milimeter) thick A.C sheet of plywood sheet and fixed to wooden plugs with C.P brass screws and washers (confirming to BIS specification) complete with in all respect.including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing C.P. Brass Towel rail complete with C.P. Brass brackets fixed to wooden plugs with C.P. Brass screws :- (i) 750mm x 20mmm complete with in all respect.including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing chromium plated brass soap dish with C.P. Brass brackets fixed to wooden cleats with C.P. Brass screws complete with in all respect.including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing 15 mm (Fifteen millimetre) dia C.P. Brass bib tap with Capstan head of Jaguar as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing brass full way valve with wheel:-(a) 15mm nominal bore omplete with in all respect.including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

b) 20mm nominal bore

Providing and fixing C.P. stop cocks :(a) 15mm dia omplete with in all respect.including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing PVC water storage tank of ISI : 12701 marked, G.I. inlet and outlet connection, 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level :-ii) 1000 litres net capacity tank omplete with in all respect.including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete.ii) 110 mm dia. complete with in all respect.including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete.ii) 110 mm X 75 mm. omplete with in all respect.including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing plastic seat (Solid / Hollow type) and cover for wash down water closet with C.P. Brass hinges and rubber buffers :SOLID TYPE:a white plastic seat and cover complete with in all respect.including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing C.P. stop cocks 15 mm (fifteen milimeter) dia (confirming to BIS Specification ) complete with in all respect.including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing C.P. Brass waste for wash basin or sink :-(I) 32mm dia complete with in all respect.including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing M.I. Union for wash basin or sink :-(I) 32mm dia complete with in all respect.including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

(i)Providing and fixing 600mm x 120 mm glass shelf with C.P. Brass bracket and guard rail complete, fixed to wooden plugs with C.P. Brass screws. complete with in all respect.including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing P.V.C connection with brass unions :-(a) 300/450mm length :-(i) 15mm nominal bore complete with in all respect.including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm (three millimetre) thick bolts and nuts complete /including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC door bend with oval access door insertion rubber washer 3 mm Three millimetre) thick bolts and nuts ISI market complete including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals

Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC plain bends ISI marked including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals

Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC Collar ISI marked including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals

Providing and fixing PTMT jet spray of approved quality and color with one meter tube as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Constructing chamber 600mm x 600mmx750mm inside size for fire/hydrants with C.I. surface box 350mmx 550mm top and 165 mm deep (inside) with changed lid and RCC top slab 1:2:4 mix (1 cement : 2 sand 4 graded stone aggregate 20mm nominal size) 100mm thick foundation concrete 1:5:10 ( 1cement : 5 sand : 10 grades stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement :3 sand) finished with a floating coat of neat cement including curing complete :-With 150 mm thick walls of reinforced cast in situ plain cement concrete walls in 1:2:4 mix (1 cement:2 sand : 4 grades stone aggregate 20 mm nominal size complete with form work and reinforcement with 6mm bars not exceeding 150 mm centres both ways. complete with in all respect.including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing cast iron cover with frame light dully rectangular single seal pattern internal dimension 455mm x 610 mm total weight cover and frame to be not less than 38 kg with (Weight of cover 23 kg. and weight of frame 15 Kg.) 300 mm wall of square rubble masonry coursed with hard stone of approved quality ing cement mortar 1:3 complete with in all respect.including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

LEKH RAJ

LABH CHAND

Sandeep Kumar

M/S KESHAV CONSTRUCTIONS