Provision of Vocational Lab for PM Sri KV School at Naval Station Bheemunipatnam

Amount

Surface dressing not exceeding 15 cm deep and getting out in Soft / Loose soil complete all as specified and as directed.

Excavation over areas not exceeding 1.50 m in depth and getting out in Soft / Loose soil complete all as specified and as directed.

Excavation over areas exceeding 1.50 m and not exceeding 3.00 m in depth and getting out in Soft / Loose soil complete all as specified and as directed.

Removal of excavated material [Soil] to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick of excavated soil complete all as specified and as directed. Note: A deduction of 10% shall be made from total computed volume of filling to cater in bulk irrespective of machinery used for ramming.

M & L for PCC 1:4:8, Type D–2, using 40mm graded stone aggregate as in Foundation, Fillings, Mass concrete, Footings etc complete all as specified and as directed.

M & L for Pre-Construction Anti-Termite Treatment for treating the Backfill in Contact with Foundation @ 7.5 Litres of Emulsion per Square Metre of Vertical Surface [Area of the sub structure in contact with backfill to be measured] complete all as specified and as directed.

M & L for Pre-Construction Anti-Termite Treatment for treating the Top Surface of Filled Earth @ 5 Litres of Emulsion per Square Metre of surface complete all as specified and as directed.

M & L for Pre-Construction Anti-Termite Treatment for treating the Soil Under Plinth Pprotection @ 5 Litres of Emulsion per Square Metre of surface area complete all as specified and as directed.

M & L for Pre-Construction Anti-Termite Treatment for treating the Soil along with External Perimeter of the Building by applying Emulsion@ 2.25 Litres per Running Metre of the perimeter wall complete all as specified and as directed.

M & L for RCC M–30 Design Mix, using 20mm graded stone aggregate as in Foundations including Pile Caps, Rafts, Footings, Foundation Beams, Plinth Beams, Bases for Columns, Fillings, Mass Concrete, Basement Slabs etc. etc. complete all as specified and as directed.

M & L for RCC M-30 Design Mix, using 20mm graded stone aggregate as in Columns, Pillars, Piers, Posts and struts etc. complete all as specified and as directed.

M & L for RCC M-30 Design Mix, using 20mm graded stone aggregate as in Beams, Cantilevers, Bressummers, Lintels over 1.5m Span etc. complete all as specified and as directed.

M & L for RCC M-30 Design Mix, using 20mm graded stone aggregate as in Slabs supported on Walls, Beams, Columns, in Floors, Roofs, Landings, Balconies, Canopies, Deck Slabs and in Shelves and the like and the like complete all as specified and as directed.

M & L for RCC M-30 Grade, Design Mix, using 20mm graded stone aggregate as in Chajjas, Facias & Fins etc. complete all as specified and as directed.

Use and removal of Steel Formwork to Sides of concrete Foundations, Pile Caps, Footings, Bases of Columns, Raft and Raft Beams, Sides and Soffits [if any] of Foundation and Plinth Beams and similar work, Vertical or to Batter for Rough Finished surfaces complete all as specified and as directed.

Use and removal of Steel Formwork to Sides of Pillars, Posts, Struts, Piers, Columns and Stanchions of any Shape / Cross Section for Fair Finished surfaces of concrete complete all as specified and as directed.

Use and removal of Steel Formwork to Sides and Soffits of Floor or Roof Beams, Beam Haunchings, Girders, Bressummers, Lintels, Cantilevers, Shelves including Supports, Overhangs, etc, Splays between Floors and Beams and similar works for Fair Finished surfaces of concrete complete all as specified and as directed.

Use and removal of Steel Formwork to Soffits of Suspended Slabs such as Roof Slabs, Floor Slabs, Landings and similar work not exceeding 200mm thick [Horizontal or Sloping] for Fair Finished surfaces complete all as specified and directed.

Use and removal of Steel Formwork to Chullah Hoods, Chajjas, Troughs and similar items including Edges and similar works for Fair Finished surfaces of concrete complete all as specified and as directed.

S & F Reinforcement using High Strength Corrosion Resistant Deformed TMT Bars of Grade Fe–500D of 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

S & F Reinforcement using High Strength Corrosion Resistant Deformed TMT Bars of Grade Fe–500D of 6mm to 8mm dia, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

S & F Reinforcement using High Strength Corrosion Resistant Deformed TMT Bars of Grade Fe–500D of 5mm to 10mm dia bars as in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

M & L for brick work with Fly Ash bricks, straight or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:6 complete all as specified and as directed.

M & L for brick work in half brick thick walls using Fly Ash bricks straight or curved on plan to any radius built in Cement Mortar 1:4 including 2 Nos of 6mm dia bars at every fourth course of brick work complete all as specified and as directed.

M & L for Providing Precast Cement Concrete Solid Block Masonry with Solid Blocks exceeding 100mm width of PCC 1:3:6, Type – C1 using 20mm graded stone aggregate set in Cement Mortar 1:6 complete all as specified and as directed.

M & L for rendering on fair faces of brick / concrete surfaces, 15 mm thick in Cement Mortar 1:6, surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M & L for rendering 5mm thick in cement mortar 1:4 over a backing coat of 10mm thick in CM 1:6 on concrete or brick masonry surfaces including mixing water proofing compound as per manufacurers instructions and finishing the top surface even and smooth without using extra cement complete all as specified and as directed. Note: Water proofing compound will be measured and paid separately.

M & L for rendering 5 mm thick in Cement Mortar 1:3 on fair faces of concrete surface of ceiling surfaces finished even and smooth without using extra cement complete all as specified and as directed.

Supply only Integral Liquid Water Proofing Compound [ISI marked] of approved make complete all as specified and as directed.

Supply only Integral Water Proofing Compound [ISI marked] of approved make complete all as specified and as directed.

M & L for Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc and brushing neat cement slurry with 3.0 KG of cement per Sq.m area, rendering 10mm thick in cement mortar 1:3 on concrete surfaces finished even and smooth without using extra cement including mixing of water proofing compound of approved make as per manufacturers instructions for levelling the surface smooth to receive the water proofing membrane, priming the surface with a coat of Oil Based Bituminous Primer conforming to IS – 3384 [Latest] @ 0.3 Litre / Sq.m, laying APP Modified [Polyester Reinforced] Membrane of 3mm thick weighing not less than 3.8 KG / Sq.m confirming to IS – 16532 [2017], by torch application with side overlap of 100mm & end overlap of 150mm & tucked into the chases on vertical surfaces by thermo fusion and finished with a coat of bituminous aluminium paint @ 100 grams per Sq.m on top for water proofing treatment complete all as specified and as directed. Note: Water proofing compound will be measured and paid separately.

M & L for preparing newly plastered wall surfaces and applying two or more coats of Cement based Wall Care Putty on walls including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coats of Acrylic Washable Distemper over One Coat of Alkali Resistant Primer on walls complete all as specified and as directed.

M & L for preparation of newly plastered Wall surfaces and applying Two coats of Weather Proof Exterior Emulsion Paint [100% Acrylic] over a Coat of Weather Proof Exterior Primer of same manufacturer as that of paint complete all as specified and as directed.

M & L for preparing newly plastered Ceiling Surfaces and applying Three Coats of White Washing complete all as specified and as directed.

Spreading, levelling and well ramming including watering as required with excavated soils in layers not exceeding 25cm thick in Floors complete all as specified and as directed.

M & L for Hardcore of Gauge not exceeding 63 mm of Broken Stones or Boulders, deposited, spread and levelled in layers not exceeding 15 cm thick watered and rammed to a true surface in broken boulder complete all as specified and as directed.

M & L for 75 mm thick, PCC 1:4:8, Type D-2, using 40mm graded aggregate as in Sub base for flooring complete all as specified and as directed.

M & L for 50 mm thick, PCC 1:2:4, Type B-1 using 20mm graded aggregate as in Floors / Hard standing etc, surface finished even and smooth with out using extra cement complete all as specified and as directed.

M & L for Granite Stone Slabs of 18 to 20 mm thick of Colour Mexican Red / Ruby Red / Z Black / Pearl Black as in Floors, Treads of Steps, Landings of Staircase, Window Cills, Cooking Platform etc. with machine cut edges, Table rubbed and prepolished to smooth mirror finish all to required sizes, granite stone slabs shall be of design / pattern as directed, including diagonals, inlays, borders, margins in two or more colours / shades, designs / patterns of stone slabs, set and bedded with grey cement [slurry] and jointed and pointed flush using polymer based cementitious tiling joint filler to match the shade of the Granite Slabs including screed bed or bedding layer of mortar 20 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: Single stone slab shall be used for entire Width and Length of Treads of Steps, Landings of Staircase, Window Cills, Cooking Platform etc. The edges of Treads of Steps, Window Cills, Cooking Platform etc. shall be Bull Nosed / Half Rounded. The edges of the Treads and Landings shall also be provided with Three Nos of Grooves.

M & L for Glazed Polish finished coloured Designer Chequered Cement Concrete Tiles of thickness 23 to 25mm, made with M-25 Grade Precast Cement Concrete, Hydraulically pressed of size not less than 300 X 300 mm, of approved Shape, Colour, Design and Pattern, set, jointed and pointed in neat cement slurry to match including screed bed or bedding layer of mortar 20 mm thick in Cement Mortar 1:4 complete all as specified and as directed.

M & L for Kota Stone Slabs of 20 to 25 mm thick as in Floors, Treads of Steps, Window Cills etc. with machine cut edges, including Diagonals, Inlays, Borders, Margins in Two or more Colours / Shades, Designs / Patterns of Stone Slabs, set and bedded with Grey Cement [Slurry] and jointed and pointed with Grey Cement slurry mixed with a Admixture of Pigment to match shade of Slabs, Rubbing and Grinding with Mechanical Equipment fitted with suitable Grit Size Carborundum Stones and Polishing with Oxalic Acid to smooth, bright Mirror finish including screed bed or bedding layer of mortar 20 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: Single Stone Slab shall be used for entire Width and Length of Steps, Window Cills, etc. The edges of Treads shall be Bull Nosed / Half Rounded. The edges of the Treads and Landings shall also be provided with Three Nos of Grooves.

M & L for Kota Stone Slabs of 20 to 25 mm thick as in Skirting, Dado, Risers of Steps, Jambs, Pillars etc. with machine cut edges, including Diagonals, Inlays, Borders, Margins in two or more Colours / Shades, Designs / Patterns of Stone Slabs, set and bedded with Grey Cement [Slurry] and jointed and pointed with Grey Cement slurry mixed with Admixture of Pigment to match shade of Slabs, Rubbing and Grinding with Mechanical Equipment fitted with suitable Grit size Carborundum Stones and Polishing with Oxalic Acid to smooth, bright mirror finish over backing coat of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. Note: Single Stone Slab shall be used for entire Height of Skirting / Dado / Risers and Joints shall match with the Flooring.

M & L for Joint Free Glazed Ceramic Tiles, Edge Cut, Concept Type, Coloured, Premium Quality, of size 450 mm X 300 mm, 7 to 8 mm thick as in Vertical Surfaces such as Skirting, Dado etc set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile over backing coat of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. The colour / shade / design of tiles shall be as approved by GE.

S & F Second Class Hard Wood, Plain, Solid, Straight Chowkats and Frames, Wrought, Framed, Rebated on the Solid, Rounded or Chamfered, put together with Glue, Pinned at Joints complete all as specified and directed.

S & F Mild Steel work confirming to Fe - 290, Grade E-165 as in Bands, Straps, Supports or Stays for Rainwater, Ventilating Pipes, including Bolts, if required, Hooks [Stay], heavy, for Large Gates, Hook and Pintle Hinges, large Hasps and Staples, Chains, hand made Sliding Bolts, Clamps, Hold Fasts, Wall Ties, Hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles complete all as specified and as directed.

M & L for providing Cement Concrete, Type C1, 1:3:6 using 20mm Graded Aggregate as in Lintels up to 1.5m Clear Span, Cills, Steps, Seismic and other Similar Bands, Plinth Courses, Copings, Bed Plates etc. complete including necessary formwork complete all as specified and as directed.

S & F 35mm thick Flush Shutter Solid Core Construction with Block Board Core and Plywood Face Panels Commercial type on One Side and Decorative Choice Veneers on other side, with 6mm thick Teakwood Lipping and fitted to Chowkats complete all as specified and as directed.

M & L for two coats of synthetic enamel paint over one coat of pink primer to newly untreated wooden surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed.

M & L for providing and injecting chemical emulsion for Post Constructional Anti - termite Treatment at points of contact of wood work by chemical emulsion [in oil or kerosene based solution] @ 0.5 litre per hole by drilling 6 mm dia holes at a downward angle of 45 degrees at 150 mm centre to centre and sealing the same complete all as specified and as directed.

S & F 125 mm size, Butt hinges, Stainless Steel, Medium weight, bright polished including fixtures complete all as specified and as directed.

S & F Aluminium anodised Handle, Cast Type, of size 150 mm complete all as specified and as directed.

S & F Aluminium alloy anodised Sliding Door Bolt with hasp and staple [Bolt Type] of size 300 mm and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

S & F Aluminium anodised barrel Tower Bolt of size 200 mm size of extruded section complete all as specified and as directed.

S & F Floor Door Stopper of size 150 mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring complete all as specified and as directed.

S & F Powder Coated [120 Microns thick], Mild Steel work confirming to Fe - 290, Grade E-165, as in framed work such as Grills, Gratings, Ladders etc with ends of bars shouldered and/or riveted, or forged into spikes, framed Guard Bars, Barred Iron Doors, Ladders, framed Balusters, Walk Ways, Railings, framework of Water Tanks and similar work including preparation of surfaces including pre-treatment for degreasing, phosphatising etc. before powder coating complete all as specified and as directed. Note: The Grills shall be Powder Coated with two coats of powder coating of 60 Microns thick each of approved colour. The Powder coating shall be Matt Finished.

S & F Decorative type Stainless Steel Curtain Rod of 25 mm dia including PVC rings @ 100 mm centre to centre and Decorative type Stainless Steel Globe type Brackets of size suitable to 25mm dia curtain rod complete all as specified and as directed.

M & L for 75mm thick, PCC 1:3:6, Type C-1, using 20mm graded aggregate as in Plinth protection etc. surface finished even and smooth with out using extra cement complete all as specified and as directed.

S & F Bib Taps, Long Body, cast copper alloy, 15 mm dia, Chromium Plated, Fancy Type, with crutch or butterfly handle, screwed down for iron pipe and fixed etc. complete all as per Jaquar Catalogue No. CON-107KN or its equivalent in Marc / Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine complete all as specified.

S & F Stainless steel kitchen sink, made of stainless steel 1 mm thick, with plugs, washers and Waste Fittings, 32 mm dia, Brass, Chromium plated, and 32mm dia PVC flexible Waste Pipe, 750 mm long including bedding in cement mortar on to dwarf wall or including fixing cantilever CI Brackets and connecting union to pipe, overall size 495mm X 420mm, bowl size 410mm X 330mm X 160mm complete all as specified and as directed.

S & F PVC Nahani Trap 100mm dia with Grating including jointing to waste pipe fixed in Cement Concrete, Type B1, 1:2:4 complete all as specified and as directed.

S & F 18mm thick, Prelaminated MDF Board, One Side Decorative Choice Lamination and other side Balancing White, Medium Density, Exterior Grade fixed with screws to wooden frames, partitions, shelves, cupboards, door panels complete all as specified and as directed.

S & F Magnetic Catches with Striking Plate, First quality suitable for Cupboard shutters complete all as specified and as directed.

S & F 150mm Long Stainless Steel Fancy type Handle, suitable for Modular type Cupboard Drawers / Shutters including Screws and Washers complete all as specified and as directed.

S & F Continuous [Piano] Hinges, Mild Steel, Bright finish or Electrogalvanised and width of Flaps 30mm [When Open] complete all as specified and as directed.

S & F Hasp and Staple, safety type of aluminium anodised including bolt to hinge plate, fixed with screws of 100mm size complete all as specified and as directed.

S & F Gun Metal Globe or Gate Valve of Class - I, Pressure Tested of 1.5 Mpa, 25 mm bore with iron wheel head, screwed both ends for iron pipe, confirming to IS, ISI Marked complete all specified and as directed.

S & F 75mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints, fixed to walls including necessary brackets, clamps as in rain water down pipes complete all as specified and as directed.

S & F 75mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S & F 75 mm bore PVC [SWR] Bends of any radius with Access Door including jointing with solvent cement complete all as specified and as directed.

S & F Angle Cock, 15 mm dia, cast copper alloy with capstan head, Chromium Plated, screwed down high pressure with crutch or butterfly handle for iron pipe etc. complete all as per Jaquar Catalogue No. CON-053KN or its equivalent in Marc / Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine complete all as specified.

S & F Rotational Moulded Polythene [HDPE] Water Tanks, Double Layered, ISI Marked, Cylindrical & Vertical Type 500 Liters Capacity hoisted and fixed in position including provision of 32mm/25mm dia spouts for connecting inlet, outlet, over flow and washout pipes complete complete all as specified and as directed.

S & F Ball Valves, 20 mm Bore, high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe [Minimum Weight 25mm - 455 Grams] etc complete all as specified and as directed.

S & F 32mm outer dia of pipe, 3–layer PP–R Polypropylene random copolymer] concealed pipes of SDR 7.4 [PN–16] UV stabilised and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings complete to walls, ceilings or in floors etc. including testing complete all as specified and as directed.

S & F 25mm outer dia of pipe, 3–layer PP–R Polypropylene random copolymer] concealed pipes of SDR 7.4 [PN–16] UV stabilised and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings complete to walls, ceilings or in floors etc. including testing complete all as specified and as directed.

S & F in repairs 150mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

M & L for concrete bed to drain pipes of size 150 mm bore packing under and haunching against the sides of pipes after they are laid and fitted in cement concrete, Type C2, 1:3:6, using 40mm graded stone aggregate complete all as specified and as directed.

M & L for providing Precast RCC 1:2:4, Type B-1, using 20mm graded stone aggregate as in Landings, Cover Slabs [for Manholes etc], Chullah Hoods, Chajjas, Water Troughs, Mangers, Shelves and similar articles with plain faces set in Cement Mortar 1:6 complete all as specified and as directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel [½ round or ¾ section] in cement concrete 1:2:4 type B1 smooth finished, and reforming benching as required for 150 mm dia of pipe complete all as specified and as directed.

M & L for 100 mm thick, PCC 1:4:8, Type D-2, using 40mm graded aggregate as in Sub base for flooring complete all as specified and as directed.

M & L for Inter Locking Paver Blocks of 60mm thick, made with M35 Grade Pre-Cast Cement Concrete using 20 mm graded stone aggregate, PVC Mould reflective type, Hydraulically Pressed of approved shape, size, pattern and colour conforming to IS - 15658 including 50mm thick Sand Cushion / Bed to Inter Locking Paving Blocks including filling interstices complete all as specified and as directed.

M & L for providing Precast Cement Concrete Kerb Stones, Dividers of 100 mm thick with or without chamfered angles and flat, splayed, rounded or mitred tops Type, B1, 1:2:4, using 20mm Graded Aggregate, including all mouldings, set in Cement Mortar 1:4 including necessary earthwork excavation and applying Two Coats of synthetic enamel paint of approved complete all as specified and as directed.

M & L for Plain / Reinforced cement concrete Type C1 [Nominal Mix] 1:3:6 using 20mm graded stone aggregate Cast in Situ in Lintels up to 1.5m Span, Cills, Steps, Seismic and Other Similar Bands, Plinth Courses, String Courses, Lacing Courses, Parapets and Railings up to 60 cm in Height, Copings, Kneelers, Apex Stones, Bed Plates including Weathering, slightly rounded or chamfered angles and throating as directed including use and waste of form work, complete all as specified and as directed.

M & L for Point Wiring complete with 1100 Volts, FRLS Grade, 1.5 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable, conforming to IS - 694 drawn through and including heavy duty PVC Conduit, 20 mm dia including all accessories concealed in Walls / Roofs / Floors / Ceiling etc. or surface type / semi concealed type and Modular Type Pressed Metal Flush Box made out of 2mm thick MS Sheet of suitable size and including Modular type Base / Grid Frame & Cover Frame for housing Modular Type Switches, Sockets and Regulators etc. concealed in walls, including 1100 Volts, FRLS Grade, 1.5 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable as earth continuity conductor with colour coding and connecting to Earth Dolly for One Light / Fan Point / Bell Point controlled by One Switch complete all as specified and as directed.

All as per Serial Item No. 86 above but One 3 Pin Switch Socket Outlet 5 Amps on Independent Board complete all as specified.

All as per Serial Item No. 86 above but for One 3 pin Socket Outlet 5 Amps on the Same Board with other switches complete all as specified and as directed.

All as per Serial Item No. 86 above but one 3 Pin Switch Socket Outlet 15 Amps on independent board, with 1100 Volts, FRLS grade, 4 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable confirming to IS - 694 and including 1100 Volts, FRLS grade, 4 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable as Earth Continuity Conductor.

M & L for Sub main wiring with 2 runs of single core 6 Sq.mm Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade, ISI Marked, drawing through and including heavy duty PVC Conduit, 25 mm dia with all accessories concealed in Walls / Roofs / Floors / Ceiling etc. or surface type / semi concealed type including One run of 6 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade earth continuity conductor complete all as specified and as directed. Note: 3 runs of 6 Sq.mm & one run of 25 mm dia PVC Conduit will be measured as one unit.

S & F Switch, Modular Type, One Module, Single Pole, One Way, 6 Amps, 230 Volts complete all as specified and as directed.

S & F Switch, Modular Type, One Module, Single Pole, One Way, 16 Amps, 230 Volts complete all as specified and as directed.

S & F Socket Outlet, 3 Pin, 6 Amps, Modular Type, Two Modules, 230 Volts, complete all as specified and as directed.

S & F Socket Outlet, 3 pin, 16 Amps and 1 pin, 5 Amps, Modular Type, Two Modules, Multipurpose, 230 Volts complete all as specified and as directed.

S & F Electronic Fan Regulator, Stepped Type, Modular Type, One Module, 120 W, AC, 230 Volts, Single Pole complete all as specified and as directed.

S & F Ceiling Rose, Surface Bakelite, 65 X 50 mm, Three Terminals, 230 Volts complete all as specified and as directed.

S & F Surface & wall mounted Energy efficient LED Tube Light Fitting, of not less than 2000 Lumens output, 5700K of cool white, with extruded Aluminium housing and robust construction with necessary acrylic diffuser & Integrated Electronic Driver, all accessories internally prewired and connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm with existing complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

S & F MCB DB, TPN, 4 Way, 415 Volts, Vertical, with DIN Channel, Double Door with 200 Amps rated bus bar suitable for mounting MCBs and provision for MCCB as incomer complete all as specified.

S & F MCCB, FP, 100 Amps, 36 KA, 415 Volts, 50 Hz, suitable for fixing on N3 Frame complete all as specified and as directed.

S & F Energy efficient, Low Noise, Ceiling Fan, 1200mm Sweep, BEE 5 Star Rated, with BLDC Motor, Copper Wound, 350 RPM, with Double Ball Bearing, Conforming to IS - 373, ISI Marked, suitable for operation on Single Phase, 240 Volts, AC, 50Hz, of approved colour including Down Rod, Canopies, 3 Nos. Blades, Shackles, Safety Rope, Hanging Clamps, Bushes and having P.F >0.94, Service Value >6.5, Air Delivery >215 CMM, Power Consumption less than 35 Watt, THD less than 5% with speed control by Electronic Regulator including connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed.

S & F Exhaust Fan, 300mm Sweep, 1400 RPM, Metal Body, Heavy Duty, with Double Ball Bearing, Conforming to IS - 2312, ISI Marked, suitable for operation on Single Phase, 240 Volts, AC, 50 Hz, including Louvers Shutter / Grill, BEE 5 Star Rated and of approved colour including connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm and fixing in existing opening and making good the disturbed surface to match with existing and complete all as specified and as directed. Make: Crompton Greaves / Havells / Almonard / Bajaj / Orient

S & F MCB DB, SPN, 8 Way, 240 Volts, Vertical, with DIN Channel, Double Door with 200 Amps rated bus bar suitable for mounting MCBs complete all as specified and as directed.

S & F MCB, DP, 40 to 63 Amps, 10 KA, C Curve, AC, 230 Volts, 50 Hz complete all as specified and as directed.

S & F MCB, SP, 6 to 32 Amps, 10 KA, C Curve, AC, 230 Volts, 50 Hz complete all as specified and as directed.

VASANTHA NAIDU ASSOCIATES (BID ID -3484472)

SRI VENKATA SAI MANIKANTA CONSTRUCTIONS (BID ID -3489219)

SWATHI CONSTRUCTIONS (BID ID -3480837)

ROHITH INFRA (BID ID -3490480)