CA NO GE (SOUTH) AMB 61 2023 2024 SPL REPAIRS TO BLDG NO HT 06 (OR LIVING LINE) AND DRAINS AT 946 TPT COY ASC UNDER GE (SOUTH) AMBALA CANTT

Amount

Taking down chowkats or frames with shutter, area not exceeding 1.50 Square metre (w/o taking off shutters from frames) and removing from site, including cutting holes in wall/concrete for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces in CM (1:3) and finishing the surfaces to match with existing finish complete all as specified and directed. (NOTE : - The quoted rate shall be deemed to include for fixing of hold fast in the same opening irrespective of position of hold fasts and no separate item for making good of hold fasts shall be paid).

Taking down chowkats or frames with shutter, area exceeding 1.50 Square metre but not exceeding 4 Square metre (w/o taking off shutters from frames) and removing from site, including cutting holes in wall/concrete for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces in CM (1:3) and finishing the surfaces to match with existing finish complete all as specified and directed. (NOTE : - The quoted rate shall be deemed to include for fixing of hold fast in the same opening irrespective of position of hold fasts and no separate item for making good of hold fasts shall be paid).

Taking down old unservicable wooden shutter of any descritption exceeding 1.00 sqm each but not exceeding 2.00 sqm each and removal from site including iron mongry, complete all as specified and directed.

Supply and fixing of pressed steel frames for doors of size 125 x 60 mm, 1mm thick, with one or more rebates including, hold fasts of 25mm x 4mm FI, 25cm long, 6 Nos in each chowkhat, necessary lugs, 3 Nos 100 mm MS butt hinges medium weight, cold rolled, welded for each shutters of frame, lock strike plate, including sanding, tarring backs of chowkhats, PCC 1:3:6 type C-0 filling in frame, 2 Nos 12 mm dia MS tie bars at the bottom of frame and one shop coat of red oxide primer etc complete all as specified and as directed.

Supply and fixing of factory made 35 mm thick, second class hard wood rail and style, plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commrcial veneering on both faces ace, size of rails and stiles as per IS 1003 (part-I) kiln seasoned and chemical pressure treated complete all as specified and directed.

Supply and fixing of 2nd class (hollock) factory made 35mm thick glazed skelton door shutters, open rebated and prepared to receive glass, gauge etc. divided into squares edges of framing, plain, chamfered or rounded, mitred fitted with cut and mitred beads for securing glass/gauge etc. with sizes of members of shutters as specified in para 8.24(a) of SSR 2009 (Part I), complete all as specified and directed.

Supply and fixing of factory made flush shutters 35 mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides, ISI marked complete all as specified and as directed.

Supply and fixing of factory made PVC hollow door frame of size 50 mm x 47 mm with wall thickness of 5 mm made out of extended 5 mm rigid PVC foam sheet cut at corner and jointed with 02 Nos, 150 mm long brackets of size 15 mm x 15 mm mild steel square tubes 19 gauge including vertical door profiles reinforced with 19 mm x 19 mm steel square tube of 19 gauge (EPDM) rubber gasket weather seal provided through out the frame and fixed to wall with 65/100 mm long mild steel screws through the frame by using PVC fasteners (minimum of 04 Nos. of screws to be provided for each vertical number & minimum 02 Nos. for horizontal member), complete all as specified and directed.

Supply and fixing of factory made solid PVC moulded door shutter with wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site with 03 Nos extruded aluminium alloy butt hinges 100mm, 02 Nos aluminium tower bolt 150 mm, 02 Nos aluminium handle 150 mm for each shutter all as per specification & drawing complete all as specified and directed

Supply and fixing of butt hinges, medium weight, cold rolled, mild steel, ISI marked 100 mm size complete all as specified and directed.

Supply and fixing of aluminum anodized, barrel tower bolts of extruded section 150mm long complete all as specified and directed.

Supply and fixing of extruded aluminium alloy handles, fabricated type, anodized of size 150 mm long complete all as specified and directed.

Supply and fixing of 300 mm aluminum anodised sliding door bolt, ISI marked, with hasp, staple (bolt type) complete with clamps bolt not less than 16mm dia and fixing clips of sheet, cast or extruded section and fixing bolts an sliding bolt of extruded section or cast aluminum alloy, complete all as specified and as directed.

Supply and fixing in repair of steel ventilator of section framed fixed type and fixed wire mesh with flat bends 10 mm x 3 mm with nuts / bolts complete including fixing lugs, necessary PCC 1:3:6 type C-0 for filling bed blocks of hold fasts/lugs, etc complete all as specified and directed.

Supply and fixing in repair of steel window box type, using ERW hollow 'P' section, factory made, comprising double frame for and including gauged and glazed skelton shutter, 30mm thick, jointed internally with flat iron 25x3mm complete including hinges, handle, tower bolts, stops, lugs etc. all as shown on drawing No. TD-219 sheet 1/3 to 3/3 of HQ CE Chandigarh Zone as applicable including PCC (C-O ,1:3:6 using 12.5 graded stone aggregate) bed blocks for hold fasts, complete all as specified and directed. NOTE : - (i) For the purpose of measurement & payment double shutter both glazed and gauzed with frame shall be considered as one unit. (ii) Unit rate quoted against this item shall also include the iron mongery and grill 10 mm square bar irrespective of whatever shown on drawings and one shop coat of zinc chromate primer . The pattern of grill shall be all as shown on drawing. (iii) Glazing, wire mesh and painting shall be measured and paid for separately.

Supply and fixing galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm fixed with tinned tacks or galvanised wire staple with beads to wooden joinery when fixed in panels of joinery and with screws when fixed to steel windows, complete all as specified and as directed.

Supply and fixing sheet glass 3mm thick, ordinary quality , in square not exceeding 0.5 Square metre each pane and glazing with oil putty to steel window and with wooden beads to wooden shutters complete all as specified and as directed.

Material and labour for preparation of new or previously untreated wooden surfaces of any description, not other wise described over 10cm width or girth and apply two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Material and labour for preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Supply and fixing in repair of galvanized steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks or galvanized wire staple complete all as specified and as directed.

Supply and fixing in repair of sheet glass 3mm thick, ordinary quality and glazing with oil putty, in square not exceeding 0.5 Sqm each pane and glazing with oil putty to steel window and with wooden beads to wooden shutters, complete all as specified and as directed.

Supply and fixing in repair of mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete fixed to stone/ concrete chowkats with flat iron 40x3 mm size 75 cm long with necessary bolts, etc. complete all as specified and directed.

Supply and fixing in repair of aluminium pre coated of choice colour designed type 25 mm tubular rod in curtain rod, 1.6mm fancy type including PVC golden colour brakets, latto and wall to wall socket etc., complete all as specified and directed.

Material and labour for premium quality, joint free, non skid coloured ceramic tiles, area of each tile exc 0.11 sqm but not exceeding 0.18 sqm, 7 to 8 mm thick as in floor, set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the surface over and including 15mm thick screed bed or layer in cement mortar (1:4) including dismantling of existing tiles etc including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

Material and labour for premium quality coloured glazed ceramic tiles (300 x 450 mm x 7 to 8mm thick) as in vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the shade of tiles over and including rendering 10mm thick in cement plaster 1:3 finished rough surface to receive tiles including dismantling of existing wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

Demolition of old brick masonry built in cement mortar of any description including all quoins, archs, pillars etc complete all as specified and directed.

Material and labour for brick work with sub class ‘B’ bricks, straight or curved on plain exceeding 6 metre mean radius in cement mortar (1:6) complete all as specified and directed.

Supply and fixed in repair of 15mm fancy type, chromium plated, angle cock, cast copper alloy, screwed down high pressure with crutch or butterfly handle, heavy with adjustable wall flange, complete all as specified and directed.

Supply and fixed in repair of stop valves, cast copper alloy ISI marked screwed down, high pressure, with crutch or butter fly handle screwed both ends for iron pipe or for unions , suitable for 15 mm bore tubes, complete all as specified and directed.

Supply and fixing in repair of CP bib tap screwed down high pressure, long body, cast copper alloy, chromium plated` with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union, complete all as specified and directed.

Supply and fixed in repair of vitreous china squatting pan of Orrisa pattern size 580 x 440mm white (Ist quality) with ‘P’ or ’S’ trap, front or back inlet and foot rests of any pattern complete including provision of lime concrete bed and connection to flush pipe excluding flushing cistern, flush pipe and bracket and making good the disturbed area complete all as specified and directed

Supply and fixing in repair of vitreous china wash hand basin white flat back of size 550x440mm including CI brackets and 15mm chromium plated fancy type, long shank pillar tap cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, PVC connection 450 mm long having PTMT nuts and 32 mm dia brass chromium plated waste coupling and making good to disturbed portion including 32 mm dia PVC waste pipe etc, complete all as specified and directed.

Supply and fixing in repair of 10 litres PVC valve less, symphonic action type low level flushing cistern ISI marked, white/coloured , with inlet ball valve, float and handle including flush pipe of polyethylene of low or high density or PVC 32mm dia for low level cistern and brackets complete all as specified and directed.

Supply & fixing in repair of sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12mm wide and chromium plated brakects guard and railing 60cm long complete all as specified and directed.

Supply and fixing in repair 20 mm dia brass chromium plated tubular towel rail 'D' type 60 cm long between flanges, including one pair of fixing brackets complete all as specified and directed.

Supply and fixing in repair of chromium plated soap dish, any type, fixed to plugs with chromium plated brass screws etc complete all as specified and as directed.

Supply and fixing in repair of chromium plated shower roses 125 size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed.

Supply and fixed in repair of 32/38 mm PVC waste pipe for urinal , wash hand basin and sink complete all as specified and directed.

Supply and fixing of sheet glass corner assembly consisting of 5.5mm thick sheet glass shelf 300mmx300 mm with chromium plated bracket guard and railing complete fixed in repair all as specified and directed.

Supply and fixing in repair PVC connections 450/600mm long and 15mm dia with PTMT nuts and PVC washers on both ends, complete all as specified and as directed.

Supply and fixing of GI tubing, ISI Marked, 15mm bore, `medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors including necassary cutting/chasing/pinning in wall and making good the disturbed surfaces as per existing wherever required, including taking down of old tubing as existing at site and removal, complete all as specified and as directed.

Supply and fixing of GI tubing, ISI Marked, 20mm bore, `medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors including necassary cutting/chasing/pinning in wall and making good the disturbed surfaces as per existing wherever required, including taking down of old tubing as existing at site and removal, complete all as specified and as directed.

Supply and fixing of water storage tank of 500 ltr capacity, HDPE triple layer, cylindrical, vertical with closed top and FDA approved, 100% UA stabilized, rust proof, ISI marked, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm high pressure with polythene float and flynut, ISI marked, screwed and suitable for iron pipe 20 mm bore complete including dismantling/ taking out of old water tank & removing from site complete all as specified and directed. Note:- Tank shall be white and make of tank shall be engraved on the tank.

Supply and fixing of anodised GI snap grid frame work for false ceiling grid 605x605 mm fixed with Hangers 4 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long including Supply and fixing Gypsum Board 12mm thick as in ceilings fixed with screws as per manufactures instructions including taking down existing false ceiling any type including grid etc complete all as specified all as specified and directed. NOTE : - Unit rate quoted against this item shall also includes taking down and refixing the same of any electrical board, switch, sockets, light and fittings, fans etc after carrying out necessary relevant work and making good to match with existing surface effected for this area etc complete all as specified and directed.

Supply and fixing of pre-painted galvalume, aluminuim zinc coating, GI based corrugated steel sheet, 0.50mm thick, conforming to IS-15961, of approved colour, having tensile strength of 550 MPa, as in roof covering/cladding to wall, fixed with self tapping screws including taking down of old sheets of any descriptions as existing on site complete all as specified and as directed. Note- The sheets shall have super durable polyester quality paint of approved colour, 150 gm/sqm total on both sides, suitable for exterior application conforming to IS-15965.

Dismantling timber scantling 40 Sq. cm and over in section, in any position of unframed/ framed work complete all as specified and as directed.

Supply and fixing of mild steel, rolled sections as in main or cross beams, hip and jack rafters, purlin where connected to comman rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates conforming to grade Fe290-W(Gde-E-165), complete all as specified and directed.

Supply and fixing of PVC (SWR) 110 mm pipe single socket in any length with rubber ring joints fixed to wall or in floors including dismantling of pipes of any description any length including bends etc complete all as specified and as directed.

Supply and fixing of PVC (SWR) 75 mm pipe single socket in any length with rubber ring joints fixed to wall or in floors including dismantling of pipes of any description any length including bends etc complete all as specified and as directed.

Supply and fixing of PVC (SWR) bends 110 mm bore complete all as specified and as directed.

Supply and fixing of PVC (SWR) bends 75 mm bore complete all as specified and as directed.

Supply and fixing in repair of PVC (SWR) junction single, (Single T) 110mm bore equal or unequal fitted with access door complete all as specified and directed.

Supply and fixing in repair of PVC (SWR) junction single, (Single T) 75mm bore equal or unequal fitted with access door complete all as specified and directed.

Supply and fixing in repair of 110 mm bore PVC (SWR) vent cowl complete all as specified and as directed.

Supply and fixing in repair of 75 mm bore PVC (SWR) vent cowl complete all as specified and as directed.

Supply and fixing in repair of PVC (SWR) floor trap 110 mm dia plain with PVC grating including jointing with solvent cement complete all as specified and directed.

Taking down cement plaster of any description and in any position including raking out joints, hacking for key, scrubbing down with water etc of any thickness complete all as specified and as directed.

Material and labour for 15mm thick rendering in cement mortar (1:4) on surface of any description of brick or concrete and finished the surface even and smooth without using extra cement complete all as specified and as directed.

Material and labour for 15mm thick rendering in cement mortar (1:6) on surface of any description of brick or concrete and finished the surface even and smooth without using extra cement complete all as specified and as directed.

Material and labour for rough cast plaster with and including 15mm thick rendering in CM 1:3 on brick wall or concrete surface as specified in clause 14.22 of SSR Part-I complete all as specified and directed. Note:-(i) After applying the under coat of cement and sand mortar 1:3 not less than 10 mm thick and while it is still in plastic state the rough cast mixture consisting of crushed stone or fine gravel aggregate (which is generally of size between 6 to 12 mm depending on the texture required) mixed with coarse sand and cement in the ratio of 1: 1: 1 shall be applied and finished even. (ii) The mix of cement and sand shall be made slightly loose/wetter than normal for rendering to ensure that larger aggregates are thoroughly covered. (iii) Contractor's quoted rate shall include all above provisions and no extra shall be admissible on this account.

Material and labour for preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of alkali resistant primer on walls complete all as specified and directed.

Material and labour for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper with hand roller, over a coat of alkaline resistant primer over a coat of wall care putty not less than 1mm thick as per manufacturer's instruction complete all as specified and directed.

Material and labour for preparation of old plastered or unplastered surfaces of walls by washing rubbing and applying one coat of cement base paint complete all as specified and as directed.

Material and labour for preparation of old plastered or unplastered surfaces of walls by washing rubbing and applying one coat of oil bound distemper complete all as specified and as directed.

Material and labour for 50mm thick PCC (1:3:6) type C-1 using 20mm graded mechanically crushed stone aggregate as in plinth protection finished even and smooth without using extra cement with & including 10mm wide, 30mm deep joints at the rate of 3.00 mtr centre to centre and at every turning & filling the joints with 85/25 grade bitumen and sand (1:3 ratio) mixture including demolition of cement concrete in ground floor and pavings not exceeding 15 cm below or above ground level etc complete all as specified and directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation, etc or for shafts, wells, cesspits, manholes, pier holes, etc n.exc 10 Sqm on plan and n' exc. 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in soil complete all as specified and directed.

Removing surplus excavated soil to a distance n.exc 50 metre & depositing where directed at a level n.exc 1.5 metre above the starting point complete all as specified and directed.

Material and labour for PCC 1:2:4 type B1 (using 20 mm graded mechanically crushed stone aggregate) as in lintels upto 1.5m clear span, coping and other similar bands, plinth courses etc and the like bands, plinth course etc including weathering, slightly rounded or chamfered angles and throating, including necessary from work etc complete all as specified and directed.

Material and labour for PCC 1:4:8 type D-2 using 40 mm graded mechanically crushed stone aggregates as in foundation, sub base and mass concrete complete all as specified and directed.

Material and labour for precast RCC 1:2:4 Type B-1 (using 20 mm graded crushed stone aggregate) as in manhole covers, including necessary form work etc, set and jointed in CM 1:4 complete all as specified and directed. (Note: Reinforcement shall be measured and paid separately under respective items of this BOQ)

Supply and fixing of mild steel TMT bars 8 mm dia and over, cut to length, bend to shape required including cranking, bending spirally for hopping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Dismantling/taking down carefully aluminium/ copper point wiring (light, fan, socket or power) complete, including fixtures and fittings such as switches, ceiling roses, pendants, regulators , sockets, light fittings etc., removing materials to stores for keeping in safe custody for taking credit and making good the disturbed surfaces of wall, floors, ceiling etc to match with the existing surfaces with matching OBD/White wash/Distemper complete all as specified and as directed.

Material and labour for concealed point wiring using approved colour coding as per IS, with multi stranded copper conductor 1.5 sqmm (Nominal area), single core, FRLSH (FIRE Retardant Low Smoke and low Halogen), PVC insulated and unsheathed stranded cable drawn through and including non metallic, heavy duty PVC concealed conduit not less than 25mm dia and its fittings including all tees, bell mouth pieces and fixing accessories such as couplers, saddlers, pipe hooks etc, PVC junction boxes ISI marked with GI flush boxes / sunken boxes made out of 1.2mm thick of any module from 2 to 18 module confirming to IS-5139(pt-I) of 1969 and IS:14772-2000 with earth dolly including modular cover plates with frame i.e. inner and outer plate extended upto 25 mm over sunken box for housing the modular switches, socket outlets, fan regulators etc with brass screws and brass washers and making good the disturbed surfaces as per existing for one light / fan / bell point contorlled by one switch including 1.5 sqmm single core PVC insulated and unsheathed FRLSH (FIRE Retardant Low Smoke and low Halogen) copper cable, 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor upto common earth and connecting to common earth dolly with suitable size of lugs for one light point/ fan point/bell point controlled by one switch complete all as specified and as directed. NOTES : - (i) The quoted rates shall be deemed to be inclusive for cutting chases by chase cutter in wall/pillars/columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface to match with the existing surface. The portion of point wiring at ceiling shall be in surface conduit of suitable size fixed on ceiling surface with using necessary accessories/fittings. (ii) Point wiring & earth wire shall be connected to each & every flush/sunken box. (iii) All screws, fasteners, bolts, nuts & washer shall be cadmium plated & the cost of which is deemed to be included in the quoted unit rates.

Description all as per item No 75.00 above but for socket out let point 5 Amps on same board complete all as specified and directed.

Description all as per item No 75.00 above but for socket out let point 5 Amps on independent board complete all as specified and directed.

Description all as per srl item No 75.00 above but point wiring for one socket out let 15 & 5 Amps (independent) controlled by one switch with using 2.5 Sq mm (nominal area) stranded copper conductor complete all as specified and directed.

Supply and fixing of modular switches, one way, 6 amps one module, 230V, 50 Hz supply, complete all as specified and directed.

Supply and fixing of modular switches, one way, 15 Amps, one module, 230 volt , AC supply, complete all as specified and directed.

Supply and fixing of modular socket outlet 6 amps, 2/3 pin combined 2 module, 230 volt, complete all as specified and directed.

Supply and fixing of modular socket outlet 6/15 Amps, 3 pin, 2 module, complete all as specified and directed.

Supply and fixing of fan regulator step type one module / 2 module, 100w 230 Volts, 50 Hz, AC complete all as specified and directed.

Supply and fixing of modular switches, bell push, 6 amps one module, 230V, 50 Hz supply, complete all as specified and directed.

Supply and fixing of ceiling rose surface bakelite 65x50mm, 3 terminal complete all as specified.

Supply and fixing of door bell electric ,ding dong /musical type, single phase 230 volts, ISI marked complete all as specified.

Supply and fixing of lamp holder, PVC/polycarbonate type with back plate suitable for batten fittings,complete all as specified.

Supply and fixing of in repair of sheet metal enclosure SP with two pin and earth plug and socket including top with one single pole, MCB 20 Amps, 'B' curve, 240 volts complete all as specified and directed.

Supply and fixing of indoor decorative LED tube light fitting 1x 20W, 220V, AC decorative box type with opal diffuser, including 20 watt LED tube, T8 with aluminium extrusion heat sink and connecting up with two core 1.5 sq mm copper conductor cable from connector to ceiling rose to connection of light including disconnecting and taking down old unserviceable light fitting of any description and in any position complete all as specified and directed.

Supply and fixing recess/ surface mounted LED flat panel 2' x 2' with high efficient LEDs and glare free full decorative light fitting, 36 watt, energy efficient provided with including LED 36 watt with provision of 2/3 core PVC copper conductor cable 1.5 Sqmm size to light fitting and complete including disconnecting and taking down existing light fitting and removal complete all as specified and directed.

Supply and fixing of surface mounted LED tube light fitting with high efficient diffuser mirror light, aluminium housing in CRCA body suitable and including 10 watt LED tube rod high efficient, AC 220-240 volts, 50 Hz and connecting with copper conductor flexible cable of size 0.50 Sqmm from ceiling rose to connector of the light including disconnecting and taking down old existing light fitting of any description and in any position complete all as specified and directed

Supply and fixing of LED bulk head light fitting, 10 watt with min 800 lumen, industrial model IP 65, energy efficient with lamp 10 watt with provision of 2/3 core PVC copper conductor cable 0.5 Sqmm size from ceiling rose to light fitting complete including disconnecting and taking down old existing light fitting of any description complete all as specified and directed.

Supply and fixing of LED lamp 9 watt threaded/pin end warm/cool lamp type as per site requirement suitable for fixing on existing batten/wall light fitting complete all as specified and directed.

Supply and fixing of LED security light luminaire 45 watt, pressure die cast aluminum housing, toughened heat resistant glass, IP65 protection, better optics for uniform distribution with multiplte LEDs not less than 2 W each and having optical grade polycarbonate lens with all accessories internally pre wired and bracket made up of GI pipe, light grade, 25mm dia, 0.60 metre long, bent to required length, fixed to wall with two clamps made of 20 x 3 mm mild steel flat minimum 15cm long, 4 nos 8mm dia bolts with nuts including connecting up with two core 1.5 sq mm copper conductor cable from connector to ceiling rose to connection of light complete all as specified and directed.

Material and labour for concealed sub main wiring with two single core FRLSH PVC insulated unsheathed copper conductor cable 4.0 sqmm drawn in and including rigid non metallic PVC medium grade 25 mm dia concealed conduit with accessories on wall or ceiling with one additional PVC insulated , stranded copper conductor FRLSH of 4.0 sqmm, green colour for earth continuity conductor including taking down old unserviceable sub main wiring and making good the disturbed surface complete all as specified and directed. NOTE : - 3 run of cable and 1 run of conduit shall be measured as 1 unit. (ii) The quoted rates shall be deemed to be inclusive for cutting chases in wall/pillars/columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface to match with the existing surface. The portion of sub main wiring at ceiling shall be in surface conduit of suitable size fixed on ceiling surface with using necessary aceessories/fittings.

Material and labour for concealed sub main wiring with two single core FRLSH PVC insulated unsheathed copper conductor cable 6.0 sqmm drawn in and including rigid non metallic PVC medium grade 25 mm dia concealed conduit with accessories on wall or ceiling with one additional PVC insulated , stranded copper conductor FRLSH of 6.0 sqmm, green colour for earth continuity conductor including taking down old unserviceable sub main wiring and making good the disturbed surface complete all as specified and directed. NOTE : - 3 run of cable and 1 run of conduit shall be measured as 1 unit. (ii) The quoted rates shall be deemed to be inclusive for cutting chases in wall/pillars/columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface to match with the existing surface. The portion of sub main wiring at ceiling shall be in surface conduit of suitable size fixed on ceiling surface with using necessary aceessories/fittings.

Supply and fixing of sheet metal enclosures vertical distribution board VTPN, (MCCB DB) 4 ways, double door, 415 volts with 200 amps rated bus bar IP 54 protection, with shrouded neutral bar and insulated bus bar and earth link, with and including MCCB 4 pole thermal release type, 125 Amps, 25 KA as incomer and MCBs as out going complete with making suitable size of MS cabinet 2 mm thick dully grouted on the wall (flush) with opening arrangement including making connections with suitable size of lugs/thimbles/glands and making good the disturbed surface matching with existing surface including taking down existing unserviciable MCCB/DBs including MCBs complete all as specified and directed.

Supply, installation, testing of SPN distibution board 8 way,double door , IP 43, as per IS 8623 including 200 Amps fully insulated copper bus bar, insulated neutral bar, earth bar, door earthing, reversible doors, PAN assembly for easy installation and also incoming and outgoing connections with suitable size of lugs/thimbles/glands including taking down existing unserviciable MCB/DBs including MCBs complete all as specified and directed.

Supply and fixing of MCB single pole, 240 volts, 50Hz , breaking capacity 10KA, 'B' curve 6 to 32 Amps, including connection with suitable size copper lugs complete all as specified and directed.

Supply and fixing of MCB single pole, 240 volts, 50Hz , breaking capacity 10KA, 'B' curve 40 to 63 Amps, including connection with suitable size copper lugs complete all as specified and directed.

Supply and fixing of MCB single pole and neutral, 240 volts, 50Hz , breaking capacity 10KA, 'B' curve 40 to 63 Amps, including connection with suitable size copper lugs complete all as specified and directed.

Material and labour for earthing with galvanised steel earth plate electrode 60cm x 60cm x 6.0 mm thick buried directly in ground vertically at a depth not less than 2.25metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level, earth plate surrounded from all sides by 15cm thick packed layer of charcoal dust and common salt filling in alternate layers and electrode connections by using galvanised iron wire 4 mm as earthing lead (upto terminal point) by means of bolts, nuts, check nuts and washers made of galvanised iron and thimbles and protected by light grade 15 mm dia GI pipe connected to main switch board or main control board and GI pipe medium grade 20mm bore for watering and including funnel , wire mesh, 50 mm thick precast RCC 1:2:4 type B1using 20 mm graded stone aggregate , reinforced with 8 mm dia dedormed /TMT bars 3 nos both way 12 mm dia round bar handle and PCC chamber pit with PCC (1:3:6) type C-2 using 40mm graded stone aggregate, including excavation and earth work in any type of soil, returning , filling in approved soil and disposal of surplus soil to a distance not exceeding 50m all as specified and shown in electrical plate No 3 of SSR 2009 (Part-I) complete all as specified and as directed. Note :- (i) Earth lead wire and its protection pipe upto and including 7.50 mtr only from top of earth electrode are included under this item. (ii) On testing if the earth resistance is not obtained within permissible limit, earthing will be re-done at NO extra cost ,till the desired earth resistance is obtained. (iii) Any joint in earth lead from earth electrode to test point shall not be allowed/permitted.

Supply, laying and testing of cable XLPE insulated, armoured heavy duty electric cable with standred aluminium conductor, 1100 volts grade, cross-sectional area of size 25 Sqmm 4 core including dismantling existing any type and any size cable complete all as specified and directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation, etc or for shafts, wells, cesspits, manholes, pier holes, etc n.exc 10 Sqm on plan and n' exc. 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in soil complete all as specified and directed.

Removing surplus excavated soil to a distance n.exc 50 metre & depositing where directed at a level n.exc 1.5 metre above the starting point complete all as specified and directed.

Material and labour for supply and filling sand with clean dry fine sand unwashed including gently punning around cables in trenches for cable protection complete all as specified and directed. NOTE: - Punned thickness shall be measurement & paid.

Material and labour for brick protection covers over cable using sub class B old size brick laid along length of cable complete all as specified and directed.

Taking down old ceiling fan any sweep or any type and deposited to MES store yard complete all as directed.

Taking down old exhaust fan any sweep or any type and deposited to MES store yard complete all as directed.

Supply and fixing of ceiling fans, AC, single phase, 230V, 50Hzs, copper wounded of 1200mm sweep with BLDC technology, maximum power input upto 35W service value not less than 6.0, copper wire insuction motor with 5 star BEE rating complete alongwith blades, electronic regulator, canopy cover, down rods 'U' clamp, 3 core PVC flexible cable 1 sqmm for making connection of fan and hanging the fan in clamp, connecting with ceiling rose to fan complete all as specified and as directed.

Supply and fixing of heavy duty exhaust fan metallic body 300 mm sweep with and including louvers, electric, single phase 1400RPM, 240 volt 50 Hz complete and making suitable hole in existing cement concrete / brick walls built in cement mortar 1:4 and removing unserviceable/loose/broken debris upto 500m distance and making good the disturbed surfaces to match with the existing surface including plastering as required & finishes including grouting four Nos rag bolts, nuts & washers and connecting with 3 core copper flexible cable of size 23/0.0076 including testing & commissioning after installation at site complete all as specified and directed.

Material and labour for hanging only ceiling fan any type/ sweep after repair and connecting up including provision of three core PVC insulated and unsheathed copper conductor cable of size 0.5 Sqmm from ceiling rose to connector to fan including refixing of blades complete all as specified and directed.

NOTE:- Amount of credit of Rs. 1,08,730.50 for retrieved materials is mentioned in Schedule of Credit Page No 21 & 22 of tender documents in pdf form which will be deducted offline while acceptance of tender.

Gupta Enterprises

Swami Enterprises

M/S M S BUILDER AND CONTRACTORS

Parveen Kumar

power house batteries

V K Constructive Builders