Renovation and additional work for Patratu Lake Resort(Including Island), Ramgarh Dist.

Amount

DESMANTLING WORK

Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in?Charge.

Dismantling 15 to 40 mm dia G.I. pipe including stacking of dismantled pipes (within 50 metres lead) as per direction of Engineer?in-Charge

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.15.23.1 For thickness of tiles 10 mm to 25 mm

Dismantling pucca brick or lime work including stacking serviceable materials in countable stacks within 15M. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Dismantling old plaster and pointing in cement or lime and raking out joints to 15 mm,depth watering and disposal unservieable materials with all lead all complete as per directed by E/I (Payment will be done as per actual work done)

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge

EARTH WORK

Earth work in excavation in foundation trenches in ordinary soil ( vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I.

Extra for earthwork in hard soil as per specification and direction of E/I. ( vide classification of soil item-B)

Filling in foundation trenches and plinth in layers not exceeding 150mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50M and lift of 1.5M all complete as per building specification and direction of E/I. (Mode of measurement compacted volume)

Providing coarse clean Sand in Filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/I. (Mode of measurement compacted volume).

CONCRETE WORK

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Reinforced cement concrete work in beams,suspended floors.roofs having slope upto 15 degree landings balconies,shelves,chajjas,lintels,band,plain windows sills,stair cases,above plinth level upto floor five level ,excluding the cost of centering,shuttering and finishing and reinforcement,with 1:1.5:3 (1 cement :1.5 coarse sand (zone-III) :3 graded stone aggregate 20 mm nominal size) (Payment will be done as per actual work done)

Centering and shuttering including strutting,propping etc. and removal of form for

Suspended floor,roof,landing,balconies and access platform

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Edges of slabs and breaks floors and wall

Above 20 cm wide

Providing Tor steel reinforcement of 8mm dia rods as per approved design and drawing exclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. TMT Fe 500 (only valid for Tata (Tiscon),SAIL,JSPL,Electrosteel Steel Ltd.Bokaro &Vizag ( RINL)

Providing Tor steel reinforcement of 10mm,28mm,32mm dia rods as per approved design and drawing exclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. TMT Fe 500 (only valid for Tata (Tiscon),SAIL,JSPL,Electrosteel Steel Ltd.Bokaro &Vizag ( RINL)

Providing 250mm. Wide brick drain in cement mortar (1:6) with av. 150mm clear depth and 250mm apron including cost of eartwork involved with 75mm cement concrete (1:4:3) over one brick designation 75A flat soling in proper grade and slope at the base the drain duly plastered in C.M. (1:3) with punning over exposed surface all complete as per building specification and direction of E/I.

Providing and laying cement concrete in kerbs, steps and the like at or near ground level excluding the cost of centering, shuttering and finishing. 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

BRICK WORK

Providing designation 75B one brick flat soling joints fitted with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I.

Providing designation 75A brick work in C.M (1: 6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I.

Providing designation 75A brick work in C.M. (1:6) in foundation and plinth approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes an

Providing designation 125mm thick reinforced designation 75A brick work in C.M. (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, carriage of materials, scaffolding, raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of E/I.

PLASTER & PAINTING, FINSHING WORK

Providing 12 mm Thk. cement plaster(1:6) on wall with clean coarse sand of FM-1.5 including screening, curing with all leads & lifts of water, scaffolding taxes & royalty all complete as per building specification and direction of E/I (Payment will be done as per actual work done)

Providing 1.5mm cement punning including curing, carraige of water with all leads and lifts as per building specification and direction of E/I.

Mirror polishing on marble work/Granite work/stone work where ever required to give high gloss finish complete.

Floor polishing on masonry or concrete floors with wax polish of approved brand and manufacture.

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge :Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and fixing 18 mm thick gang saw cut,mirror polished,premoulded and pre polished,machine cut for kitchen platforms,vanity counters, window sills, facia and similar locations of required size, approved shade, colour and taxture laid over 20mm thick base cement mortar 1:4 (1 cement: 4 coarse sand) treated with white cement, .mixed with matching pigments, epoxy touch ups,including rubbing,curring, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Granite stone slab all colour and texture expect black,Cherry/ Ruby red

Area of slab over 0.50 Sqm-(Kitchen Slab)

Providing and laying machine cut, mirror polished, Italian Marble stone flooring laid in required pattern in linear portion of the building all complete as per architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm including pointing with white cement slurry admixed with pigment to match the marble shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.18 mm thick Italian Marble stone slab, Perlato, Rosso verona, Fire Red or Dark Emperadore etc.

All sections to be galvanized @ 120 gms/SQM (both side inclusive), fixing with clip in tiles into spring 'T' with: GI MTR.al Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/ SQM (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation.

Providing and laying matt finished vitrified tile of size 600x600x8mm having with water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.

Making plinth protection 50 mm thick of cement concrete (1:3:6) (1 cement:3 coares sand:6 graded stone aggregate 20 mm nominal size) over 75 mm thick bed of dry brick ballast 40 mm nominal size,well remmed and consolidated and grouted with fine sand,including necessary excavation.levelling and dressing and finishing the top smooth.

Providing and applying white cement bsed putty/White cement of average thickness 1 mm of approved brand and manufacturer,over thr plastered wall surface to prepare thesurface even and smooth conplete.

Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding washing of floor and taxes all complete as per building specification and direction of E/I.

Finishing walls with textured exterior paint of required shade :Old work (Two or more coats on existing cement paint surface applied @ 3.28 ltr/10 sqm

Providing & Applying high quality acrylic modified resin based texture of Dholpur/Red sand stone Pattern with anti algae and UV resistance properties to be applied as intermediate finish in desired pattern @ 43.04 kgs/10 sqm to form film of 1- 1.5 mm thickness after scrapping and properly cleaning the surface to remove loose particles from the plaster surface, followed by top coating with Premium Acrylic Smooth exterior paint with Silicone additives of required shade by two or more coats @ 1.43 litres/10 sqm, complete as the direction of Engineer -in-Charge.

Providing French spirit polishing over new wooden surface to give desired texture and gloss with approved make and shade of ready mixed French polish including preparing the surface after cleaning removing dirt,scales grease including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Providing one coat of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface throughly , scaffolding and taxes all after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Providing and fixing expansion hold fasteners on C.C. /R.C.C./Brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete.Fastener with threaded dia 12 mm

Providing and laying 500x500x40 mm thick Turf paver (Turfpave XD) on 150 mm thick sub grade of compacted bed of 20 mm thick nominal size stone aggregate and base course and filling with 150 mm thick jamuna sand, including spreading, well ramming, consolidating and finishing smooth etc. all complete as per direction of Engineer-in-charge

Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

P/Fixing at all heights designer stepped POP false ceiling with framing and GI ceiling section, intermediate runners and angle, perimeter, give flush finish etc.including in provision for lighting.

P/making cove in POP false celing with the help of p.o.p and G.I perimeter etc.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of Tile 600x600 mm

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge.Size of Tile 600x600 mm

Deduct for not grouting the joints with white cement and matching pigment in the items of fixing of vitrified tiles.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineerin- Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete.

Providing and laying 25mm thick kotah stone slab flooring of approved size texure and colour over 19mm thick base of lime mortar (1:1:1) (limeputty:surkhi:coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I. (iv) 600X600 mm size

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour and shade Area of slab upto 0.50 sqm

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For fixed portion

Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of PVC / neoprene gasket required (Fittings shall be paid for separatel

Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm)

Supplying, fitting and fixing 35mm thick solid core type decorative single leaf flush door shutter with both sides decorative veneered with black board core bended with high quality phenol formal dehydes synthetic resine of standard make with Aluminium fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.

Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete :

Supplying, fitting and fixing good quality, well dressed and well seasoned sal wood work in chaukhat in doors, windows skylights, fanlights and C/W celetial windows openings, including wedge over all clamps complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all completeas per building specification and direction of E/I.

Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) :Red sand stone - exposed face fine dressed with rough backing.

FALSE CEILING, PARTITION WORK & ALUMINIUM WORK

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I.

wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)

Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre.

The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete.

75 mm overall thickness partition with 12.5 mm thick double skin fire rated Glass Reinforced Gypsum (GRG) plaster board conforming to IS: 2095: part 3 (Board with BIS certification marks)

Providing and fixing shower enclosure made in 10 mm thick toughened fixed glass edge polished partition fixed with aluminum 'U' -channel (19mm x 25mm) inserted in floor & cutting as required and make the floor good. & 10mm toughened glass shutter to be fixed with the connectors equivalent to Ozone make of (ogc4). All glass joints shall be filled with tranparent silicon sealant including toughened glass door with necessary brass hinges, shower type- handle equivalent to Ozone make of (oghtb1), pipe fitting make equivalent to Ozone make of OSKH-1, OSKH-2, 19mm ss pipe, fixing arrangement and making necessary holes cutout etc. all complete as per instruction of Engineer in charge. (Glass make Saint Gobain /Modi Float or Equivalent) (Hardware make Ozone/Trium or Equivalent)

STEEL ROLLING SHUTTER WORK

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull peration complete, including the cost of providing and fixing ecessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 part 1 and M.S. top cover of required thickness for rolling shutters.80x1.25 mm M.S. laths with 1.25 mm thick top cover

CARRIAGE OF MATERIAL

Sand,Lead-15 KM

Stone Chips,Lead-22 KM

Brick - 7+1 km

ELECTRICAL WORK WITH SOLAR POWER PANEL

Wiring for light point/fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit,with modular types switch,modular plate,suitable size G.I. box etc.as required.Group-B

Wiring fo light/ power plug 1.5 Sq.mm FR PVC insulated copper conductor single core cable in surface/recessed copper conductor single core cable for loop earthing as required.

Supplying and fixing suitable size G.I.box with Modular plate and cover fixing 3 pin 5/6 amp modular socket outlet 5/6 amp modular typeswitch connection painting etc. as reuired accessories;-

75mmx75mmx50mm deep (4''x4'')

121mmx173mmx48mm deep (6''x8'')

Supplying and fixing Batten/ angle holder including connection etc. as required.

Supplying and fixing 2 pin 5 amp Ceiling rose on the existing junction box/wooden block including connection etc. as required.

Supplying and fixing following Piano type switch/socket on existing swiotch box.cover including connection etc. as required.

5/6 amp,one way switch

15/16 amp,one way switch

Wiring for Curcuit submain wiring along with earth wire with the following size PVC insulated copper conductor,single core cable in surface/recessed PVC conduit as required.

2x1.5 sq.mm+1x1.5 sq.mm earth wire

2x2.5 sq.mm+1x2.5 sq.mm earth wire

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

3 pin 5/6 amps,socket outlet

1200 (48'') Celling fan

20/22 W LED Tube light

SITC of following rating recess / surface mounted LED round / square shape down light luminarie with pressure die cast housing for single phase supply voltage Luminarie shall be confirm to IS: 10322 part -5 / section -2 or IEC :62722 withh all neccesary accessories as required. (Approved Make:- Havells / Philips / Crompton / Wipro).

12W LED Round Down Light

15 / 16 W LED Round Down Light

18 /20 W LED Round Down Light

Supplying installation testing and commissioning of Grid interactive roof top solar photo voltaic power generation system including all the required accessories like Solar PV module, Grid Tie invertor, arrey junction box, cabling & wiring, earthing, surge protection device, FRLSame structure for mounting of solar panel. The cell shall be poly crystaline silicon cells of 6 inch each and module efficiency shall be more than 17%. Solar module shall have linear output warranty with degradation not exceeding 0.7% FRLSom 2nd Year onwards. Minimum 80% power output must be assured at end of 25 years. The FRLSont glass of solar module shall be low iron tempered glass ARC type. Termination box shall be Thermo-plastic, IP 67 or better, UV resistant with built-in-bypass. The nominal power of a single PV module shall be minimum 540 Wp or higher. Positive power tolerance modules only to be used. RF identification tag for each solar module shall be provided inside the module and must be able to withstand environmental conditions. The solar panel shall be complience of IEC 61215, IEC 61730 certified by TUV Rheinland / UL. The solar panel shall be installed as per BOQ & detailed technical specification.

Supplying and fixing of 1X80 Watt High bay facade light complete with integrated electronic driver & ncluding connection with 1.5sq.mm FR PVC insulated copper conductor cable and earthing the body etc. as required.

S.I.T.C of Following rating approved make LED Bollard Fitting with cylindrical shape and inverted cone shape head of height 600 to 850 mm power input -8/9 watt with die cast aluminium housing opel with PC diffuser, IP-65/54 protection, conferming to IS : 10322 part 5 etc all complete as requird. (Excluding Plinth Charge.)

SANITARY AND WATER SUPPLY

Supplying, fitting and fixing viterous white glazed earthen ware I.W.C. of Parry Hindustan or any other I.S.S. approved make with 100 mm H.C.I., "p" trap 15 litres C.I.. or C. pull and let go flushing cistern of names or other I.S.S. equivalent make, complete with all fittings, C.I. or C.C. brackets 32 mm alkathene/P.V.C. telescopic flush, pipe about 2 M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pair of viterous white glazed earthenware where footrest to be fixed in floor 15 mm C.I. body brass spindle stop cock of weight not less than 50 grms. 15 mm P.V.C. connection pipe 450 mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l.(A) 580 mm long (c) with 10 lit. low level P.V.C. cistern

Supplying, fitting and fixing viterous white glazed earthen ware wash hand basin of Parry or Hindustan or any other I.S.S. approved make supported on pointed c.l. or R.S. brackets 32m C.I. brass waste 15mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350grms., 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/l.

Providing & fixing on wall face unplasticised - Rigid P.V.C. pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion. Single socketed pipes. 110mm dia

Supplying, fitting and fixing Mirrors of 6mm thick plate glass bevelled edge mirror including C.P brass revolving fittings 3mm ply wood board and C.P hinges to fix with mirror. 600X450mm

Supplying, fitting and fixing C.P. brass towel rail 20mmX600mm with bracket container

Supplying, fitting and fixing C.P. brass soap dish container medium quality with screw and hinges etc.

Providing and fixing C.P. brass angle valve for basin mixer and geyser point of approved quality conforming to IS; 8931 15mm nominal bore.15mm nominal bore

Providing and fixing C.P. brass bib cock of approved conforming to IS; 8931 : 15 mm nominal bore

Providing and fixing P.V.C..waste pipe for sink or wash basin including P.V.C. waste fitting complete..Flexible pipe 32mm dia.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stailess steel plug 40 mm including painting of fittings and brackets,cutting and making good the wall eherever required.Kitchen sink with drain board (510x1040 mm bowl depth 250mm)

Providing and fixing CPVC ( Chlorinated Polyxinyl Chloride pipes,having thermal stability for hot and cold water supply,including all CPVC plain brass threaded fittings,i/c fixing the pipe with clamps at 1.0 m spacing.This includes jointing of pipes and fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of E/I. 15mm nominal outer dia pipes

Supplying and fixing C.I. cover without frame for manholes : 500 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 kg

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Supplylng, fitting and fixing the following items complete with all materials as per specification and direction of E/I. (a) Glass shelf with C.P. brass rail (l) 600x125mm olass shelf complete

Providing and fixing of white vitreous china wall hung / floor mounted European type water closet of approved shape and size with inside glazed P trap, with concealed flushing cistern dual flush capacity of 2.1 / 4.2 LPF including soft close anti-bacterial seat & cover infused with nano silver ions (AG+) for 99.9% bacteria protection along with hinges & rubber buffers, CP brass screw, washer with all associated accessories with side gap filled with silicon sealant wherever required complete including cutting and making good the walls, floors, slab wherever required complete. Wall Hung WC with seat cover Make Kohler Model No K-18131IN-S-0 / + Concealed Flushing Cistern Make Kohler Model No K-P77027IN-M-NA+ Face Plate for Cistern Make Kohler Model No K-4177IN-M-CP / + W.C Pan Connector Make Kohler Model No K-1036902

Providing and fixing white vitreous china wash basin of approved shape and size with special fabricated brackets duly painted white, faucets as required, 32 mm C.P. brass waste.32 mm C.P. brass bottle trap & pipe to wall with rubber adopter for waste connection and C.P. brass wall flange complete in all respects including cutting and making good the walls where required. Under Counter Wash basin Make Kohler Model No K-2215IN-0 , 32 mm CP brass waste Make Kohler Model No K-45433IN-CP, 32 mm C.P. brass bottle trap with pipe to wall and C.P. wall flange Make Kohler Model No K-7314IN-CP.

Providing and fixing c.p. brass basin mixer complete in all respects including cutting and making good the walls where required.

Providing and Fixing of C.P. Brass Shower set comprising of : One No. CP brass Single Lever Concealed Diverter Make Kohler Model No. K-16316IN-4FP-CP + K-8821IN-CP, One No. CP brass OH shower head & Shower Arm Make Kohler Model No.K-45429IN-A-CP, One No. CP brass Bath Spout Make Kohler Model No.K-99060IN-CP, Including cutting and making good the walls wherever required.

Providing and fixing PTMT Bottle Trap for Wash basin. Bottle trap 31 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms.

Providing & fixing PTMT towel ring trapezoidal shape 215 mm long 200 mm wide with minimum distance of 37 mm from wall face with concealed fittings arrangement of approved quality and colour weighing not less than 88 gms

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS 8931 a) 15 mm nominal bore. 15 mm nominal bore

Providing and fixing toilet paper holder : C.P. brass

Providing and fixing lead connection pipe with heavy quality brass coupling 2 nos. at both ends etc all complete as per specification and direction of Engineer-in-charge. 15 mm dia and 45 cm long,

Supplying fitting and fixing the following items complete with all materials as per specification and directionof E/I. (a) Glass shelf with C P brass rail, (i) 600×125 mm glass shelf complete

(b) Mirrors of 6mm thick plate glass bevelled edge mirror including C.P. brass revolving fittings 3mm ply wood board and C.P. hinges to fix with mirror. (I) 600 mm×450 mm size

(II) CP brass dish container madium quailty with screw and hinges etc

(c) (III) C P brass liquid soap container

Providing, Installing & fixing storage type water heater of approved shade with copper container, glasswool insulation,stove enamelled M.S jacket, thermostatically controlled inner heater with pilot neon lamps, 15mm inlet stop cock valve, on inlet connection, 15mm dia C.P flexible connection pipe in inlet & outlet suitable for working pressure of 8 kg/sqcm complete as required. ( Make - Parry Ware Product Code- C500339). Capacity 25 litres.

Supply and fixing HINDWARE make or equivalent Health Faucet with 8 mm dia, flexible tube with wall hook and Angle stop cock with wall flange . Etc all as directed by Engineer In-Charge.HINDWARE make Health Fauce - 1.25 Mtr. long (Cat No. F160013)/ Equivalent

GUEST ROOM- INTERIOR WORK

Providing and Fixing of full ht. wardrobe depth 600mm with shutters made in 19 mm thick com. block board and 6mm thick com ply for back side to be fixed on the wall, with 19mm thick com. block board shelves inside placed horizontally & vertically, 2no. of drawer inside with self closing bright finished CP hinges,inside 0.8mm thick laminate finish. and shutters made in19mm thick com. board finish with 1.0mm thick laminate (High Glosh) of approved color and shade .The item includes providing 600mm SS finished handles on front for shutters,including necessary hardware,ss drawer handle, ss hanger rod, drawer channel etc. all complete as per drawing to the & instructionof Engineer in charge (Com. block board Boad & laminate Make Green ply/Century /Merino or Equivalent ), (Adhesive make Pidilite or equivalent) (all hardware make Hetich or equivalent),

Heavy-duty Luggage Easy foldable stand approx. Size 950mmx600mmx750mm made up High Density wood in section size 25 mm thick & 45-SOmm width, minimum load carrying capacity at least 50kg/stand, tested at site, 04 nos black durable nylon strips shall be fixed at top. Two or more coats wood surface Duco painting all sides finish Asian/Nerolac or equivalent make in approved colour shade as per direction of Engineer-in­Charge. (Com. block board Boad & laminate Make Green ply/Century /Merino or Equivalent ), (Adhesive make Pidilite or equivalent) (all hardware make Hetich or equivalent),

Providing and fixing of cabinet below additional counter in toilet (made of 19mm thk. Com. Bd. finish with 1.0mm thk. laminate finish, top finish 18mm thick granite top. inside surface finish with 0.8mm thick laminate including necessary hardware hanger rod, drawer channel etc. all complete as per drawing to the & instructionof Engineer in charge (Com. block board Boad & laminate Make Green ply/Century /Merino or Equivalent ), (Adhesive make Pidilite or equivalent) (all hardware make Hetich or equivalent),

P/Fixing Dsigner Wall paper as per approved brand and manufacture to give an even shade and color as approved by architect. & instructionof Engineer in charge . Basic 1200/- SQM.

P/Fixing wooden fins made 11mm thk. bd finish with laminate/ duco paint and fins size 150X75X 2700mm till ceiling ht. fins finish with 1mm thk. laminate/Duco paint. All work to be carried out as per drawing and instruction of Engineer in charge. ( Com. block board Board, ply & Laminate Make Green ply/Century /Merino or Equivalent ), (Adhesive make Pidilite or equivalent) (all hardware make Hetich or equivalent),

Providing and fixing Study Table with 1 nos. Chair size 4'-6"X2'-0"X2'-6"made with 19mm th.commercial block board boxing with1.0 mm thick Laminate fixed on front, top and outer sides with the help of adhesive & back and insides portion finished with enamel paint with handles, knobs & locks complete etc. as per drawing. Table should haven pedestal unit of size 450mm wide as per drawing. The pedstal unit should have 1 nos. of drawer mounted on telescopic channel and made from 18mm thick commercial plywood for sides and 6mm plywood for base. The remaining space after drawer should be made with storage and shutter. All work to be carried out as per drawing and instructions of Engineer in charge. (commercial block board, ply & Laminate Make Green ply/Century /Merino or Equivalent ), (Adhesive make Pidilite or equivalent)

Providing and Fixing MDF Wall Panneling made in hard wood frame (teak wood) 35mm x 50mm thick c/c 600mm horizontally & vertically, fixed to wall/columns with wooden plugs,then 11 mm thick Medium Density Fiber Board fixed on top of frame with 10x8 mm deep Groove & same finished with 1.0 mm thick laminate of approved quality pasted with the help of adhesive & nails screws etc including grooves to be finished with 1mm thik laminate shade as per Technical specification, drawing and instructions of Engineer in charge. (MDF Board &laminate Make Green ply/Century /Merino or Equivalent, Adhesive make Pidilite or equivalent) (all hardware make Hetich or equivalent)

Providing and fixing LCD console of Size3250x450 x450MM made in 19 mm thick commercial block board with 2 Nos of drawer with back of 6mm commercial ply and 1.0 mm thick designer laminate of approved colour and shade. Inside surface to be enamel painted. The item including all necessary hardwares, screws, locks handles, drawer channel ,ss legs 32mmx 150 ht. , etc. Wall Panneling made in 19mm thick commercial block board with 150mm depth fixed on wall with cutting and making niche size for LCD unit & cutting / provision for all electrical points as required . Outside surface to be finished with the approved 1 mm thick laminate all complete. All work to be carried out as per drawing and instruction of Engineer in charge. ( Com. block board Board, ply & Laminate Make Green ply/Century /Merino or Equivalent ), (Adhesive make Pidilite or equivalent)

Providing & Fixing Translucent Roller blinds over window opening with arrangement of closing & opening with G -string, complete in all respects as per design and instruction of Engineer in charge. (make Vista / MAC or equivalent,FABRIC MODEL NO. equivalent to ECHO (Vista) / Abstract /Silky/ Ribcord/Drizzle/Trans,)

P/Placing 15" dia glass top coffee table with S.Steel pedestal with melamine polishing complete.

Providing /Placing balcony chair

Providing and placing duoble bed with box size 1800x1950mm made in 19mm thick commercial block board boxing 300mm depth and base 75x35mm mirandi hard wood frame with. 19mm thick com.ply box opening from top side Head board size 1950x1200mmx35mm thick with quilting (leatherite) 600x1800mm and foot board 1800x450mmx35 mm thick com block board with quilting (leatherite) 300x1650mm. Rest of area finish with 1.0mm thick specified laminate with nail, screws etc.lesgs in teak wood & all edges in melamine poilsh all complete along with 2 no. side table as per drawing and as per instruction of Engineer in charge ( commercial block board Boad & Laminate Make ply/Century /Merino or sunmica oe equivalent), (without mattress)

Supplying an placing in position kingkoil Fire retardant mattress( 78"x72"x8") that uses high GSM Jacquard fabric. The Eurotop layer is quilted with 2 layers of 100% pure sleep grade Super Soft foam that enhances the comfort level and sleep experience. This is a one-side usable innerspring mattress that means your housekeeping team doesn’t have to flip the mattress after every 2-3 months. The support layer is made of specially designed convoluted high-density foam that offers the best support for the back. The core layer of the mattress uses a higher count of Pocket or Bonnell springs and comes with zero partner disturbance technology. The core layer of the innerspring is enclosed with butterfly m-springs to offer better edge support for your guests. The bottom of the mattress is quilted with anti-skid fabric and it comes with a 10 Years Warranty.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water tinnable priming coat with cement primer

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Providing and fixing in position wooden palmet of 3800mm x 300mm custom made out of 18mm blockboard duly finished with 1mm thick Laminate as per approved shade and pattern all necessary hardware complete in all respect as per drg.and direction of Architect

Supplying an placing in position kingkoil Fire retardant mattress( 78"x72"x8") that uses high GSM Jacquard fabric. The Eurotop layer is quilted with 2 layers of 100% pure sleep grade Super Soft foam that enhances the comfort level and sleep experience. This is a one-side usable innerspring mattress that means your housekeeping team doesn’t have to flip the mattress after every 2-3 months. The support layer is made of specially designed convoluted high-density foam that offers the best support for the back. The core layer of the mattress uses a higher count of Pocket or Bonnell springs and comes with zero partner disturbance technology. The core layer of the innerspring is enclosed with butterfly m-springs to offer better edge support for your guests. The bottom of the mattress is quilted with anti-skid fabric and it comes with a 10 Years Warranty.

Main curtain Lightout type OEKO-TEX Bedra,weight 330 gsm Fabric width 140cms /54 " composition 100% polyester ( D decore) with 3" pinch pleats/ box pleat and curtain just grazeing the floor

Sheer curtain OEKO-TEX SA23208P, Shade 56170.weight 63 gsm Fabric width 140cms /56 " composition 100% polyester with flame retardant (NFPA 701) ( D decore) with 3" pinch pleats/ box pleat and curtain just grazeing the floor

Curtain stiching with 3" pleats

Magnum Channel track nos ,with fitting and cartage

Supply of Bed side lamp with replacable light source Class i protection rating. Warranty 1 years (no bulb included)

Supply of Floor lamp with replacable light source Class ii protection rating. Warranty 1 years (no bulb included)

9watt cob lights

Reception area & waiting area wall wooden paneling

Providing and fixing Reception area wall panneling as per approved drawing and instruction of eng in charge

Supply, Installation, Testing & Commissioning of Display Panel: 43-inch widescreen, Direct LED 3 year warranty from OEM

Supply, Installation, Testing & Commissioning of Display Panel: 43-inch widescreen, Direct LED 3 year warranty from OEM

Supply, Installation, Testing & Commissioning of Display Panel: 85-inch widescreen, Full Array LED 3 year warranty from OEM

Artificial green wall with freme

Providing and fixing Sofa. Sofa frame work with 18mm plywood seat height 400mm high made of 100mm thk. foam (32 density) & 750mm high back in sloping form and arm rest on both side as per drawing shall be made of 40 mm thk. foam fixed in basic frame made of 18mm thick plywood. plywood ,seat and back and sides shall be be fully covered and cusioned with Fabric upholstry finish of approved pattern ,texture, color and shade including all fixtures, fasteners, nails, screw, adhesive, gunny cloth etc. complete up to the satisfaction of Engineer- in-charge. This job includes all Installation, Material & labour etc.complete.All work is to be executed as per the direction and approval of Engineer in charge . Per seat cost

SOFA CENTRE TABLE WOODEN (1200mm x 600mm) Providing and fixing Centre table made out of 40mm x 40mm Teak wood legs with outer frame made out of 40mmx60mm second class teak wood with 12mmx12mm groove all around to accommodate 12mm glass of approved shade on Top.Melamine polish of approved shade & texture on all wooden surfaces.Work include all labour, material, etc. complete and nothing will be paid extra for execution of the item. All work is to be executed as per the direction and approval of Engineer in charge .

SOFA CORNER TABLE WOODEN (600mm x 600mm) Providing and fixing Centre table made out of 40mm x 40mm Teak wood legs with outer frame made out of 40mmx60mm second class teak wood with 12mmx12mm groove all around to accommodate 12mm glass of approved shade on Top.Melamine polish of approved shade & texture on all wooden surfaces.Work include all labour, material, etc. complete and nothing will be paid extra for execution of the item. All work is to be executed as per the direction and approval of Engineer in charge .

Coustmize Reception table Providing & Fixing Table made out of 18mm thick ply finished with 1 laminate (are over exposed surface) . Table shall have pedestal units with drawers & shutter below made in 18 mm thk Comm. plywood ISI grade, finished with 1 mm thk. . The table is supported on base made of 18 thk MR Grade plywood finished with 1 mm thk mica laminate . Table shall have linning in internal exposed surfaces of drawers and Storage Cabinets of 0.8 mm thick Laminate. Drawers are to be fitted with Telescopic Channels ,Unit will also have cable manager for wires & cables. The rate shall include all necessary hardware like 75mm.long Brass/S.S.hinges/Hattich Hinges, catchers, handels,drawer Telescopic channels, locks of approved quality . e for ergonomic design.

Stackable chairs

Providing and Supplying Pool Side Chairs of powder coated MS frame structure All work is to be executed as per the direction and approval of Engineer in charge .

Outdoor table big

Outdoor table small

Multipurpose hall chairs

Bar high table

Staff bunkbed mattress

Tv paneling bar area

Wall Paneling Bar Area

HORTICULTURE AND LAND SCAPING

Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly leveling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).

Supplying and stacking sludge at site including royalty and carriage up to 5 km (sludge measured in stacks will be reduced by 8% for payment).

Supplying and stacking at site dump manure from approved source, including carriage up to 5 km Complete (manure measured in stacks will be reduced by 8% for payment) :

Screened through sieve of I.S. designation 20mm

Rough dressing the trenched ground including breaking clods.

Uprooting weeds from the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation.

Fine dressing of the ground.

Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately). C

Grassing with ' Doobs' Grass (Grassing with 'Doobs' grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn free from weeds and fit for moving including supplying good earth if needed)

In rows 15 cm apart in either direction

In rows 7.5 cm apart in either direction

Turfing Lawns with Fine Grassing including Ploughing, Dressing (Turfing lawns with fine grassing including ploughing, dressing including breaking of clods, removal of rubbish, dressing and supplying doobs grass roots at 10 cm apart, including supplying and spreading of farm yard manure at rate of0.6 cum per 100 sqm)

Maintenance of Lawns or Turfing of Slopes Maintenance of lawns or Turfing of slopes (rough grassing) for a period of one year including watering etc.

Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately)

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) :

Holes 90 cm dia, and 90 cm deep

Holes 60 cm dia, and 60 cm deep

Filling mixture of earth and sludge or manure in the desired proportion in trenches, flooding with water and leveling (cost of supplying earth and sludge or manure and mixing excluded).

Providing and fixing M. S. tree guard 50 cm square in plan, height 1.40 meter above ground level and 0.50 metre below ground level. The vertical members shall consist of four nos of angle iron of size 25x25x5 mm 1.9 long, one at each corner and 8 nos flat iron of size 25x5 mm 1.4 long. The vertical members shall be welded to 4 nos 25x6 mm M. S. flats placed horizontally around the vertical member of the cage. One name plate of 1 mm thick M.S. sheet of size 250x100 mm shall be welded to the tree guard near the middle height and lettered CPWD / PWD/ any other approved name. The tree guard shall be fixed to the ground by making suitable holes and by embedding four corners leg in the ground , including refilling the earth, compaction etc. complete. The tree guard shall be painted with two coats of paint of approved brand and manufacture over a coat of primer, complete in all respect.

Preparation of mounds of various size and shape by available excavated / supplied earth in layers not exceeding 20 cm in depth, breaking clods, watering of each layer, dressing etc., lead upto 50 meter and lift upto 1.5 m complete as per direction of Officer-in-charge.

Providing Square Cement Concrete pots of specified size, cast with cement concrete of nominal mix 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size), reinforced with 7 nos. ( 3 nos horizontal & 4 nos vertical "U" shape) M.S. wires of 3.5 mm dia as per design, including required form work, finishing with cement punning on exposed surface, curing for specified period and stacking in required rows & height , all complete as per direction of Officer-in-charge.

Top inner width 35 cm, outer bottom width 25 cm, total height 35 cm and wall thickness 25.4 mm

Filling of the following size empty pots with mixture of good earth & manure in the ratio of 2 : 1 (Two part of Good earth & one port of manure ) and placing them on appropriate place i/c carriage of earth, manure and pots up to 50 mtr, as per direction of officer in charge. ( The cost of good earth, earthen pots & manure will be paid separately. )

Size of empty Pots 16 cm Top dia, 12 cm Bottom Dia & 14 Cm Perpendicular height.

Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water)

Trees Plant

Shrubs Plant

Hedge Plant

SEASONAL PLANTS

Providing and Displaying plants Allyssum white in full bloom well developed fresh & healthy Plant in 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.

Providing and Displaying plants Anemone hybrid (3 in one) variety well developed with fresh & healthy Flower in full bloom in 25 cm Earthen Pot/ Plastic Pot and as per direction of the officer-in-charge.

ORNAMENTAL PLANTS

Providing and Displaying Acalypha green plant well developed, fresh & healthy with good foliage, multi branch 30 to 45 cm ht. in 20 cm size Earthen Pot/ Plastic Pot bushy plant as per direction of the officer-in-charge.

GROUND COVERS PLANTS

Providing and Displaying of Alternanthera species plant of height 15 cm to 20 cm, full of branches and foliage in 15 cm size of Earthen Pot / Plastic Pot & as per direction of the officer-in-charge.

Providing and Displaying of Asparagus marrie plant, well developed 15 to 20 leaves, full of branches and foliage in 25 cm size of Earthen Pot / Plastic Pot & as per direction of the officer-in-charge.

Providing and Displaying of Syngonium miniature dwarf plant, having height 30-45 cm. with 2-3 suckers healthy foliage in Earthen Pot/Plastic Pot of size 20 cm. as per direction of the officer-in-charge.

TREE PLANTS

Supply and stacking of Alstonia scholaris plant of height 150-165 cm. in bag of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of Azadirachta indica ( Neem ) plant of height 120130cm in big polybag of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of Bauhinia blakeana (Kachnar) plant of height 120150 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of Butea frondosa (Flame of Forest) plant of height 60-75 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of Callistemon lanceolatus plant of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of Cassia fistula (Amaltash) plant of height 120-135 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of Cassia siamea plant of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of Delonix regia (Gulmohar) plant of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge

Supply and stacking of Erythrina indica plant of height 150-165 cm. in big polybag of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of Jacaranda mimosifolia plant of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of Plumeria acutifolia plant of height 120-135 cm. with 2-3 branches in HDPE bag of size 30 cm as per direction of the officer-in-charge.

Supply and stacking of Plumeria rubra plant of height 120-150 cm. with 34 branches and thick stem in big size HDPE bags as per direction of the officer-in-charge.

Supply and stacking of Pongamia glabra (Papri)plant of height 120-135 cm. in big poly bag of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of Terminalia arjuna plant of height 150-165 cm. in big polybags of size 25 cm as per direction of the officer-in-charge.

SHRUBS

Supply and stacking of plant Caesalpinia pulcherrima species of height 45-60 cm. in earthen pot of size 20 cm as per direction of the officer-in-charge

Supply and stacking of plant Calliandra, emarginata of height 45-60 cm. in earthen pot of size 20 cm as per direction of the officer-in-charge.

Supply and stacking of plant Calliandra hybrida of height 75-90 cm. with 45 branches in bag of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of plant Cestrum nocturnum (Raat ki Rani) of height 60-75 cm. with 4-5 branches in bag of size 25 cm as per direction of the officer-in-charge.

upply and stacking of plant Cassia biflora of height 90-105 cm., well branched, bushy in big size HDPE bag as per direction of the officer-in-charge.

Supply and stacking of plant Euphorbia pulcherrima (dark red double bracts) well branched of height 60-75 cm. in earthen pots of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of plant Excoecaria bicolor of height 45-60 cm. in earthen pots of size 20 cm as per direction of the officer-in-charge.

Supply and stacking of plant Hamelia patens of height 90-105 cm. bushy in big size HDPE bags as per direction of the officer-in-charge.

Supply and stacking of plant Hibiscus rosasinensis of height 60-75 cm. with 5-6 branches in p.bag of size 25 cm as per direction of the officer-in-charge.

CREEPER PLANTS

Supply and stacking of Bignonia venusta (Golden shower) plant of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.

INDOR PLANT

Areca Palm having ht. 1.20 m to 1.50 m with 5 to 6 suckers, well developed, fresh and healthy with lush green foliage in 25 cm size of Earthen pot / Plastic pot.

FRP PLANTERS POTS

ADDITION KITCHEN EQUIPMENTS

4 DOOR REFRIGERATOR , Outer body 0.8 mm pre-polish ss J4 sheet ,internal 0.5 mm ss 304 tank , with force draft cooling system ,temperature range -2 to +8 40 mm HDI quality Puff Insulation ,compressor make Emerson Copland Kirlosker , with 4" rexnold fan 4 No. ,Machine on castor wheel 4 nos. heavy duty , Lt. capacity - approx 1200Lt., 1250X700X2050

Work Top Refrigerator - Outer body 0.8 mm pre-polish ss j4 sheet ,internal 0.5 mm ss 304 tank , with force draft cooling system ,temperature range -2 to +8 40 mm HDI quality Puff Insulation ,compressor make Emerson Copland Kirlosker , with 4" rexnold fan 4 No. ,Machine on castor wheel 4 nos heavy duty , Lt. capacity - approx 450 Lt,1350X700X850

Single Deck Oven Electric 2tray - Outer SS and Inner MS with Thermostatic control Upper and Bottom heater load 6 kw,1220X820X575

Sandwich griller Single Head , Electric Load 1.8 Kw .1phse,430X370X240

SS GAS Operated Tandoor On wheel with Glass wool Insulation and Canteen type Burner Make - NGV Outer Body 18 G and Top 16 G 304,800x800x850

Exhust blower nikotra with cropmton moter 7.5 hp 3ph. with belt driven bacward type with sound proff body,1200x1000x1200 aprox

All Kitchen Euipments Items Instalation & Transpotation, all complete as per directions of Engineer-in?Charge.

Add 18% GST

Add 1% Labour cess 1%

ARUN KUMAR