Construction of Govt Senior Secondary School building at Somnachani in Tehsil Balichowki Distt Mandi SH C/o Building portion WS SI Rain water harvesting system and Septic tank

Amount

Excavation in soil in Hilly area by mechinical means in all kinds of soil such as a pick work , jumper work , blasting work both in soft and hard rock with chiesling / wedging out rock (where blasting is prohibited) and other intermediate classification of soil including cutting and trimming of site slopes and disposal unserviceable material by mechnical transport and stacking the serviceable/ useful material on the road berms as per technical specification clause 1603.1, 1603.2 ormuttams shall be left at suitable place as directed by Engineer- in - Charge and shall be removed only after attaining the formation level and after final checking of Engineer-in- Charge. The work shall be executed in workman like manner and aboid any damaged to the private / Govt. property in the vicinity of work site , if any damage occurs to any property during the course of execution shall be the absolute responsibility of the contractor , which shall have to be duly compensated by him in all cases. The recovery for useful stone 57.26 cum @ 300 (fifty seven point two six cubic meter @ Rupees three hundred)per cubic metre to Rs:- 17,178/-(Rupees Seventeen thousand One hundred seventy eight) shall be done on prorata basis for the quantity of cutting in earth work effected including carriage of material with in all leads and lifts and other incidentals and as per the direction of the Engineer-in-Charge.

Excavation in earth work in all kinds of soil and disposal of all excavated earth upto any lead of disposed earth to be levelled and neatly dressed pick work & jumper work including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Excavation in foundation, trenches etc. in earth work in all kinds of soil such as pick work, Jumper work, blasting work in soft and hard rock, conglomerated rock or saturated soil and its intermediate classification of soil, chieseling work and wedging out rock (where blasting is prohibited) and pumping or bailing out watering/dewatering upto any lift, stacking the excavated soil upto any lead from the edge of excavation and then returning the stacked soil in layer when required into plinth, sides of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Excavation in drain and channels etc. in earth work in all kinds of soils such as pick work, jumper work, pick jumper work , pick jumper blasting work , blasting work in soil and hard rock conglomerate rock or saturated soil and its intermediate classification of soil including chiseling/wedging out of rocks (where blasting is prohibited) and pumping or bailing watering/dewatering including dressing of sides and bed and disposing of excavated earth complete as per specification and including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing form work with steel plates 3.15mm. (Three point fifteen millimetre ) thick welded with angle iron in frame 30x30x5mm. (Thirty x thirty x five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to all floor level and removal of same for insitu reinforced concrete and plain concrete work including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. a) Foundation, footing basis of columns etc. and mass concrete .

b) Flat surfaces such as soffits of suspended floors, roofs ,landings and the like, floor etc. upto any thickness.

c) Columns, pillars, posts and struts in square, rectangular or polygonal in plan.

d) Beams, cantilevers, girders and lintels, sides and soffits of beams, beam hunching, cantilevers, bressumers and lintels upto any depth in all heights from any floor level.

e) Edges of slabs and breaks in floors and walls in any width.

f) Stair cases with slopping or steped soffits excluding landing.

g) Vertical surfaces such as walls(any thickness) , partitions and the like including attached pillasters ,buttresses, plinth and string courses and the like.

Providing and laying cement concrete, 1:6:12 (One cement : six Sand : twelve graded crushed stone aggregate , 40mm (Forty milimetres) nominal size ) and curing complete excluding cost of centring and shuttering in foundation and plinth including carriage of material and other incidentials in all leads and lifts and as per the direction of the Engineer-in Charge.

Providing and laying cement concrete 1:4:8 ( one cement: four sand: eight graded crushed stone aggregate 40mm (Forty millimetre ) nominal size) mechanically mixed and vibrated and curing complete excluding the cost of form work in foundation and plinth including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and laying cement concrete 1:4:8 (one cement : four sand : eigth graded stone aggregate 25mm (twenty five millimetre) nominal size and curing complete excluding cost of form work in: Foundation and plinth including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and laying cement concrete 1:3:6 (1 cement:3 sand:6 graded stone aggregate 40mm (Forty millimetre) nominal size) excluding cost of centring and shuttering in Foundations and plinth including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and laying cement concrete 1:2:4 (1 cement:2 Sand:4 graded stone aggregate 20mm (twenty millimetre) nominal size and curing complete excluding cost of form work in Foundation and plinth including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and laying reinforced cement concrete design Mix-20(twenty) grade mechanically mixed and vibrated nd curing complete excluding cost of form work and reinforced cement concrete work.The mix shall be designed as per requirement of I.S. code and and P.W.D. specification. The design mix shall be approved by Engineer-in-charge prior the casting. The theoritcal consumption of cement for the item shall be workedot as per approved design mix as per I.S. code in string courses, copings, bed plates. anchor blocks and the likes up to all floor level or as per the directions of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. Foundation, footing basis of columns etc. and mass concrete .

Suspended floors , roofs, landings and shelves and their support , balconies, beams, girders,bressumers and cantilever upto floor any level.

Columns, pillars, posts and struts upto floor all level.

Stair cases (except spiral stair case) excluding landing but including preparing of the top surface and finishing of nosing upto all floor level.

Providing and laying upto first floor two level reinforced cement concrete 1:2:4 (one cement :two Sand : four graded stone aggregate) 20mm (twenty millimetre) nominal size to give a smooth and even surface including centring and shuttering etc. but excluding cost of reinforcement in Mouldings as in cornices windows, sills etc. not exceeding 15cm (fifteen centimetre) in girth upto floor any level including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and laying cement concrete 1:2:4 (one cement :two sand : four graded stone aggregate) 20mm (twenty milimetre) mechanically mixed and vibrated and curing complete excluding cost of form work and reinforcement for reinforced concrete work including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. Walls (any thickness but not less than 0.10 m (Zero point one zero metre thickness) including attached pilasters , buttersses ,plinth and string courses etc. from top of foundation upto all floor level

Suspended floors , roofs, landing and shelves and their supports, balconies, beams , girders, bressumers and cantilever upto floor any level.

Providing Tor steel reinforcement for R.C.C. work including bending, binding and placing in position complete including cost of binding wire upto floor all level including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing in RCC work smooth finishing of the exposed surface with cement mortar 1:3 (one cement : three sand) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Extra for forming cavity 5cm to 7.5cm (five centimetre to seven point five centmetre) wide in cavity walls with necessary weep and vent holes including use of cores and cost of providing and fixing bitumastic coated M.S. Ties of 25mm x 3mm (twenty five millimetre into three millimetre) section at not less than 3 (three) ties per square metre as per approved design 1st class brick masonary including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Brick masonry using common brunt clay 2nd class brick masonry in cement mortar 1:6 (one cement : six sand) in super structure upto floor any level including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Precast concrete block masonry (including quion blocks,jamb blocks, closer etc.) with solid concrete blocks of approved size made of cement concrete 1:3:6 (one cement:three sand:six graded stone aggregate 40mm (forty millimetre) and down gaugein superstructure upto all floor level foundation and plinth in cement mortar 1:6 (one cement : six sand) upto floor any level including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Precast concrete block masonry in partition walls 10 cm (ten centimetre) thick with solid block of approved size including quion blocks, jamb blocks, closer etc. made of cement concrete 1:3:6 (one cement:three sand:six graded stone aggregate 40mm (forty millimetre) and down gauge in Cement Mortar 1:6 (one cement : six sand) upto floor any level including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Random rubble masonry/polygonal rubble masonary (uncorsed/brought to cources) with hard stone of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (onecement : six sand :twelve graded stone agreegate 20mm nominal size) at plinth level in cement mortar 1:6 (one cement: six sand) including carriage of material and other incidentials in all leads and lifts and as per the direction of the Engineer-in Charge.

Squared rubble masonry coursed with hard stone of approved quality in foundation and plinth including raking out joints in cement mortar 1:6 (one cement: six sand) including carriage of material and other incidentials in all leads and lifts and as per the direction of the Engineer-in Charge.

Squared rubble masonry coursed with hard stone of approved quality in foundation and plinth including raking out joints in cement mortar 1:3 (one cement: three sand) including carriage of material and other incidentials in all leads and lifts and as per t

Stone filling dry hand packed under floors with hard stones of approved quality including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

C/o Dry rubble masonry in breast wall and retaining walls revetment walls and parapets etc. including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing 100mm (one hundred millimetre) diameter poly Vinyl chloride pipe in Weep holes in brick masonry/stone masonry, plain/reinforced concrete and retaining /breast walls etc. extending through the full width of the structure with slope of 1V:20H towards drainage face complete as per drawings and technical specifications and including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing 1st class deodar woodwork in frames of doors,windows,clerestory,windows and other frames wrought,framed and fixed in position including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing 1st class Kail wood work in frames of false celling partitions etc. sawn and put-up in position including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing 1st class deodar wood panelled double glazed or panelled and double glazed 6mm (six millimeter) thick glass panes 2 (two)Nos. with air vaccum of 5mm (five millimetre) between both glass panes) 35mm (thirty five millimetre) thick shutters for doors windows and clerestory windows including black enamelled iron butt hinges with necessary screws including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing 35 mm (thirty five millimetre) thick including black enamelled M.S. butt hinges flush door shutters interior grade, commercial type, core of black-board construction with frame of first class hard wood and well matched commercial ply veneering with vertical grains of cross bands and face veneers on both faces of shutters including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing 30 mm (thirty millimetre) thick 1st class Deodar wood wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm (zero point fifty six millimetre) for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screws including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing M.S. Plain grills of required patterns in wooden frames of windows etc. with M.S. Flats, square or round bars with round headed bolts and nuts or by screws including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing 40x3 mm (forty into three millimetre) flat iron hold fast 40cm (forty centimetre) Long including fixing to frame with 10mm (ten millimetre) diameter bolts & nuts and wooden plugs and embeding in cement concrete block 30x10x15cm (thirty into ten into fifteen centimetre) 1:3:6 ( one cement : three sand: six graded stone aggregate 20mm (twenty millimetre) nominal size including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing 1st class indian teak wood 75 mm x 60mm (seventy five millimetre into sixty millimetre) rounded hand rails in straight length complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing Prelaminated board bwp phenol bonded exterior/interior grade both sides. 12mm (twelve millimetre) thick penalling including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing 19mm (nineteen millimetre) thick Commercial Board water proof shutters for up boards including fixing with nickel plated piano hinges with screws etc complete) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing 19mm (nineteen millimetre) thick water proof commercial board in shelves/box for cup board with butt joints & fixing with nails & screws etc complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing magnetic catcher with screws etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing 125 mm (One hundred twenty five millimetre) stainless steel decorative handles in cupboard with necessary screws etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing anodized aluminium sliding door bolt anodized colour and shade with bolts and nuts screws etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge . 300x16 mm (three hundred into sixteen millimetre)

250x16 mm (two hundred fifty into sixteen millimetre)

Providing and fixing aluminium tower bolts (berrel type) anodized trans parent or dyed to required shade and colour with screws etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge . 300x10mm (three hundred into ten millimetre)

250x10mm (two hundred fifty into ten millimetre)

150x10mm (one hundred fifty into ten millimetre)

Providing and fixing aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge . 125 mm (one hundred twenty five millimetre)

100 mm (one hundred millimetre)

Providing and fixing 150 mm (one hundred fifty millimetre) oxidized M.S. hooks and eyes including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing Double glazing with glass panes 6mm (six millimetre)glass panes 2 Nos. With air vaccum of 5mm (five millimetre) between both glass panes (weight not less than 13.75 kg/sqm (thirteen point seventy five kilogram per squaremetre) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing 75 mmx 60mm (seventy five millimetre into sixty millimetre) 1st class indian teak wood decorative cornice in straight length complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Providing and fixing 1st class Indian teak wood square edges cover fillets (beading) 19mmx6mm (nineteen millimetre into six millimetre) section including mitring at junctions with wood screws and nails complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

25 mm (twenty five millimetre) thick Kota stone slab flooring 20 mm (twenty millimetre) (average) thick base of cement mortor 1:4 (1 cement :4 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete upto floor all level including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Kota stone slab 25 mm thick in risers of steps,skirting dado and pillars laid on 12 mm (twelve millimetre) thick cement mortar 1:3 (one cement :three sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing complete upto floor all level including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and laying antiskid spartic ceremic tiles 10mm (ten millimetre) thick in flooring 300x300mm (three hundred into three hundred millimetre) size treads of steps laid on a bed of 12mm (twelve millimetre) thick cement mortar 1:3 (one cement : three sand) finished with flush pointing in white cement upto floor all level including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and laying digital ceremic tiles 8mm (eight millimetre) thick in flooring (300 x600mm) (three hundred into six hundred millimetre) treads of steps laid on a bed of 12mm(twelve millimetre) thick cement mortar 1:3(one cement: three sand) finished with flush pointing in white cement upto floor all level including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 10mm (ten millimetre) thick anti skid water proof stain and impact resistent heavy duty vetrified tiles Nitco or equivalant 600x600mmx10mm (six hundred into six hundred millimetre into ten millimetre) manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm (twelve millimetre) thick cement mortar 1:3 (one cement : three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete upto floor all level including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and laying Duro stone vetrified tiles 300x300mmx10mm (three hundred into three hundred millimetre into ten millimetre) in grey/coloured or of approved shade in skirting, of steps and dado laid on a bed of 12mm (twelve millimetre) thick cement mortar 1:3 (one cement : three sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete upto floor all level including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

40mm (fourty millimetre) 1st class deodar wood planks wooden planking toughned and grooved 20cm (twenty centimetre) wide in flooring fixing to wooden base frame with iron screws complete (base wooden frame to be paid separately) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing inside lining of PGI sheet 0.63 mm thick in shutters of doors including necessary screws, etc. Complete including carriage of materials with in all leads, lifts and other incidental complete as per the direction of Engineer-in-charge.

Providing and fixing 0.60mm (zero point sixty millimetre) thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 (twenty) microns over 5 (five) microns primer coating to back coat of polyster of 5 (five) microns over 5 (five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (six millimetre) dia metre with prepainted limpet and rubber washers complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing ridges or hips 60 cm (sixty centimetre) overall with 0.60mm (zero point sixty millimetre) thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 (twenty) microns over 5 (five) microns primer coating + back coat of polyster of 5 (five) microns over 5 (five) microns primer coating i/c fixing with prepainted iron J or L hooks, bolts & nuts 6mm (six millimetre) dia & prepainted G.I. limpet and bitumen washers complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing valley 60 cm (sixty centimetre) overall with 0.60mm (zero point sixty millimetre) thick prepainted steel sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 (five) microns over 5 (five) microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm (six millimetre) dia with prepainted G.I. limpet and bitumen washers complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 15 cm (fifteen centimetre) wide 45 cm (forty five centimetre) overall semicircular 0.60 cm (zero point sixty centimetre) Thick steel sheet prepainted sheet gutter with prepainted iron J or L hooks bolts and nuts 6mm (six millimetre) dia metre with prepainted limpet and rubber washers complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 150mm (one hundred fifty millimetre) dia pipe on wall face PVC (D-Plast) rain water pipes of working pressure not less than 4.5 kg/sqm (four point five kilogram per square metre) including filling the joints with approved adhesive complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing on wall faces PVC (D-Plast) accessories for rain water pipes including filling the joints with approved adhesive complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. PVC Plain bend 150mm (one hundred fifty millimetre) dia

PVC concrete type bend 150mm (one hundred fifty millimetre) dia

PVC shoe 150mm (one hundred fifty millimetre) dia

Providing and fixing M.S. BP Sheet 1.66mm to 2mm thick (one point sixty six millimetre to two millimetre) in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured & paid separtely) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing steel glazed doors,windows and ventilators of standerd rolled steel sections ,joints mitred and welded with 16x3.15 mm (sixteen into three point fifteen millimetre) lugs 10 cm (ten centimetre) long embedded in cement concrete blocks 15 cmx10cmx10cm (fifteen centimetre into ten centimetre into ten centimetre) size of 1:3:6(one cement:three sand:six graded stone aggregate 20mm (twenty millimetre) nominal size or with wooden plugs and screws or rawl plug and screws or with fixing clips or with bolts and nuts as required and iron fittings,including providing and fixing of glass panes with glazing clips and special metal sesh putty of approved make complete including applying a priming coat of red lead paint fixed steel windows including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing plan prepainted sheet facia with necessary screws etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing calcium silicate tile ceiling of size 600x600mm (six hundred into six hundred millimetre) of everest, dexune etc. over rady masde power costed metal heet section frame work including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing chromium plated Grab bar with necessary fitting etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Steel work welded in built up sections,trusses and framed work,including cutting ,hoisting ,fixing in position and applying a priming coat of red lead paint including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. In beams joists channels ,angles , tee ,flats with connecting plates or angle cleats as in main and cross beams,hip and jack rafters,purlins connected to common rafters and the like.

In gratings framed guard bars, ladders, railling ,brackets and similar works.

Providing and fixing angle iron cupboard frames manufactured from M.S.Angle iron section 25X25X5mm (twenty five into twenty five into five millimetre) thickness including hinges jamb,lock jamb,bead and if required angle thrashold of mild steel angle 25X25 mm (twenty five into twenty five miilimetre) welded or rigidly fixed by mechanical means,lugs with split end tails to each jamb including steel butt hinges 2.5 mm (two point five millimetre) thick with provision for locking arrangement and shock absorber as specified and applying a coat of approved steel primer after preteatment of the surface including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Applying priming coat over new steel & other metal surfaces after & including preparing the surface by thoroughly cleaning oil grease dirt and other foreign matter and scoured with wire brushes fine steel wool scrapers and sand paper complete With ready mixed priming paint brushing red lead,Red-oxide/zinc oxide chrome including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Painting two costs (excluding priming cost on new steel and other metal surfaces with enamel paint brushin to give an even shade including cleaning the surface of all dirt,dust and other foregin matters including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Applying priming coat over new wood and wood based surfaces after and including prepering the surface by thoroughly cleaning oil,grease,dirt and other foreign matter) sand papering and knotting including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Painting two coats(excluding coat) on new wood and wood based surface with enamel paint to give an even shade including cleaning the surface of dirt,dust and other foreign matter,sand papering & stoping with enamel paint other than white including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Polishing two coats with french polish on new wood and wood based surfaces to give an even surface including cleaning the surface of all dirt,dust,and sand papered smooth and including a coat of wood filler including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Finishing wall with weather proof exterior grade emulsion of approved design (Apex ultima) or its equivalent on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture on undecorated wall surfaces to give an even shade including thoroughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth including applying of putty as required for making the surface including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth. Priming coat with distemper primer including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated ceiling surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth priming coat with distemper primer for distempering with oil bound distemper on ceiling and/ or sloping roofs including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

15mm (fifteen millimetre) cement plaster in single coat on fair side of brick/concrete/stone walls for interior plastering upto floor two level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm (eighty millimetre) in girth and finished even and smooth in cement mortar 1:3 (one cement : three sand) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

6mm (six millimetre) Cement plaster to ceiling in cement mortar 1:3 (one cement : three sand) upto floor all level including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

20mm (twenty millimetre) Cement plaster in two coats,backing coat 15mm (fifteen millimetre) and finishing coat 5mm (five millimetre) thick on rough side of brick/stone masonry walls for interior plastering upto floor two level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm (eighty millimetre) in girth and finished even and smooth upto floor all level including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing plinth protection 50mm (fifty millimetre) thick in cement concrete 1:3:6 (one Cement : three Sand : six Graded stone aggregated 20mm (twenty millimetre) nominal size including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing under layer for plinth protection of 75mm (seventy five millimetre) thick (unconsolidated) bed of dry brick/stone aggregated 40mm (forty millimetre) nominal size with rammed and consolidated and grouted with fine sand including preparation of ground including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Constructing Course rubble hammer dressed 'U' shape open surface drain with side wall. 15x22 cm (fifteen into twenty two centimetre) in cement mortar 1:6 (one Cement : six Sand) and inside plastring with cement plaster 1:3 (one Cement:three Sand) including earth work and laying 10 cm (ten centimetre)cement concrete in 1:5:10 (one Cement : five Sand : ten graded stone aggregate) of 40 mm (forty millimetre)nominal size and 7.5 cm (seven point five centimetre) cement concrete 1:2:4 (one Cement : two Sand : four Graded stone aggregate of 20 mm (twenty millimetre) nominal size and finished with a floating coat of neat cement complete as per standard design. including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and laying water proofing treatment by applying cement slurry mixed with water proofing cement compound of Dr. Fixit Pidfin or equivalent consisting of applying (a) First layer of slurry of cement @ 0.488 Kg/sqm (zero point four hundred eighty eight kilogram per squaremetre) mixed with water proofing cement compound @ 0.253 kg/sqm (zero point two hundred fifty three kilogram per square metre). This layer will be allowed to air cure for 4(four) hours. (b) Second layer of slurry of cement @ 0. 242 kg/sqm (zero point two hundred fourty two kilogram per squaremetre) mixed with water proofing cement compound @ 0.126 kg/sqm (zero point one hundred twenty six kilogram per square metre). This layer will be allowed to air cure for 4 (four) hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipe and masonry with polymer mixedc slurry including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing vitreous China wash down,water closet squatting pan (Indian type W.C pan) size 580mm (five hundred eighty millimetre) (Earth work, bed concrete, foot rest and trap to be measured and paid for separately) Orrissa Pattern including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing vitreous China wash down,water closet (European type. W.C. pan) with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1(one cement : one sand) (Seat and cover to be measured and paid for separately) Anglo Indian Universal closet including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing G.I. Inlet connection for flush pipe with W.C.Pan including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing plastic seat (Solid type) and cover for wash down water closet with C.P. Brass hinges and rubber buffers white plastic seat and cover including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing Flat back type of size 430mm x 260 mm x 350mm (four hundred thirty millimetre into two hundred sixty millimetre into three hunded fifty millimetre) vitreous China bowl pattern urinal including connection the urinal with waste pipe by means of white lead mixed with choppe hemp (waste pipe to be measured and paid for separately) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing Vitreous China 5 (five) litres capacity automatic flushing cistern with a pair of C.I. Or M.S. brackets complete with fittings including C.I. Syphonic apparatus, mosquito proof lid, C.P. Brass unions and coupling for connections with inlet, outlet and overflow pipes including cutting holes and making good the same (overflow pipe to be measured and paid for separately) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 15mm (fifteen millimetre) nominal bore C.P. brass flush pipe / spreaders for urinal with fitting such as unions, clanmps etc. (all in C.P. Brass) including cutting holes and makng good the same including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing Flat back 550mmx400mm (five hundred fifty millimetre into four hundred millimetre) vitreous China wash basin with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing vitreous China padedstal for wash basin complete recessed at the back for the reception of pipes and fittings including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 32mm (thirty two millimetre) dia rubber plug for sink / wash basin including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 32mm (thirty two millimetre)dia C.P. Brass waste for wash basin or sink including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 32mm (thirty two millimetre)dia M.I. Union for wash basin or sink including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 600mm x 450 mm (six hundred millimetre into four hundred fifty millimetre) bevelled edge miror of superior glass mounted on 6mm(millimetre) thick A.C. Sheet or plywood sheet and fixed to wooden plugs with C.P. Brass screws and washers including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing C.P Brass Towel ring complete with C.P brass brackets fixed to wooden plugs with C.P brass screws including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing C.P Brass Toilet paper holder including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing choromium plated brass soap dish with C.P. Brass brackets fixed to wooden cleats with C.P. Brass screws including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing Division Plate for Urinals 600mm x 300mm (six hundred millimetre into three hundred millimetre) of Vitreous China including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 15mm (fifteen millimetre) dia C.P Brass bib tap with Capstan head including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 15mm (fifteen millimetre) dia C.P Brass pillar tap with Capstan head including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing c.p. brass angle valve 15mm (fifteen millimetre) without Nuts and pipe including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 15mm dia (fifteen millimetre) C.P. stop cocks including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 300/450mm(three hundred / four hundred fifty millimetre) long 15mm (fifteen millimetre) nominal bore lengthP.V.C connection with brass unions including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 15mm (fifteen millimetre) nominal bore brass full way valve with wheel including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 1216 16 mm (sixteen millimetre) O.D. pipe Polyethelene-Aluminium-Polyethelene (PE-AL-PE) composite pressure pipe U.V. stablized with carbon black confirming to IS-15450-2004 water supply including clamp at one metre spacing, cutting, fixing and making good the wall etc. but excluding the cost of fittings (internal work) pipes exposed on wall including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing composite end seal compression fittings as per IS-15450-2004 for cold water supply e.g. tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fittings complete including cutting and making good the walls etc. including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. Equal Tees 1216 (one thousand two hundred sixteen)

Female branch TEE 1216 X 1216 X 15 mm (one thousand two hundred sixteen into one thousand two hundred sixteen into fifteen millimetre) thread

Female ebows 1216 X 15 mm (one thousand two hundred sixteen into fifteen millimetre) thread

male thread connector 1216 X 15 mm (one thousand two hundred sixteen into fifteen millimetre) thread

Female thread connector 1216 X 15 mm (one thousand two hundred sixteen into fifteen millimetre) thread.

Couplers 1216 (one thousand two hundred sixteen)

Providing and fixing 1000 (one thousand millimetre) litres net capacity tank PVC water storage tank of ISI : 12701 marked,G.I. inlet and outlet connection, 15mm (fifteen millimetre) nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting upto all heights above ground level including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 110 mm X 90 mm (one hundred ten millimetre into ninety millimetr

110 mm X 75 mm (one hundred ten millimetre into seventy five millimetre)

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 110 mm (one hundred ten millimetre)

75 mm (seventy five millimetre)

Providing and fixing PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm thick bolts and nuts complete including fixing with approved adhesive etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 110 mm (one hundred ten millimetre )

110 mm X 75 mm (one hundred ten millimetre into seventy five millimetre)

Providing and fixing PVC door bend with oval access door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 110 mm (one hundred ten millimetre )

75 mm ( seventy five millimetre)

Providing and fixing PVC single equal branch plain ISI marked including fixing with approved adhesive etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 110 mm (one hundred ten millimetre)

75 mm ( seventy five millimetre)

Providing and fixing PVC collers ISI marked including fixing with approved adhesive etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 110 mm (one hundred ten millimetre)

75 mm ( seventy five millimetre)

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 110 mm (one hundred ten millimetre)

75 mm ( seventy five millimetre)

Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 110 mm (one hundred ten millimetre

75 mm ( seventy five millimetre)

Providing and fixing 110 mm (one hundred ten millimetre) dia PVC 'P' or 'S' trap for water closet (squatting pan) ISI marked including jointing the trap with the pan and PVC pipe with approved adhesive etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing PTMT Coloured / white automatic flushing cistern with a pair of PVC / C.I. or M.S. bracket complete with fittings including PVC syphonic apparatus, mosquito proof lid, PVC union and coupling for connections with inlet, outlet and over flow pipes including cutting holes and making good the same ( over flow pipe to be measured and paid for separately) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 32 mm (thirty two millimetre) nominal bore PTMT waste coupling of approved quality and colour including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing PTMT urinal waste coupling of approved quality and colour including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing PTMT jet spray of approved quality and colour with one metre tube including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 100 mm (one hundred millimetre) dia choromium plated grating of superior quality for floor, gully or nahani trap including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing PVC cowl IS marked including fixing with approved adhesive etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing Round Mouth Traps 100mmx100mm (one hundred millimetre into one hundred millimetre) size P or S type stoneware gully trap grade 'A' complete with C.I grating, brick masonry chamber in cement mortar 1:5(one cement; five sand) and water tight C. I . cover with frame of 300mmx300mm (three hundred millimetre into three hundred millimetre) size (inside) the weight of cover to be not less than 4.53kg (four point fifty three kilogram) and frame to be not less than 2.72 kg (two point seventy two kilogram) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Constructing manhole with R.C.C top slab in 1:2:4 mix ( onecement : two sand : four graded stone aggregate 20mm (twenty millimetre) nominal size foundation concrete1:4:8 (one cement : four sand : eight graded stone aggregate 40mm (forty millimetre) nominal size inside plastering 15mm (fifteen millimetre) thick with cement mortar 1:3 (one cement three sand) finished with a floating coat of neat cement and making channels in concrete 1:2:4 mix (1 cement : 2 sand : 4 graded stone aggregate 20mm (twenty millimetre) nominal size finished smooth complete including curing and testing Inside size 800mm x 800mm and 500mm (eight hundred millimetre into eight hundred millimetre into five hundred millimetre) deep including C.I cover with frame. (Light duty single seal pattern - 1) 455 mmx610mm (four hundred fifty five millimetre into six hundred ten millimetre) internal dimensions total weight of cover and frame to be not less than 38kg (thirty eight kilogram) (weight of cover 23 kg (twenty three kilogram) and weight of frame 15 kg (fifteen kilogram) With 300mm (three hundred millimetre) thick walls of squarred rubble masonry coursed with hard stones of approved quality in cement mortar 1:3 (one cement : three sand) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Constructing manhole with R.C.C top slab in 1:2:4 mix(one cement : two sand : four graded stone aggregate 20mm (twenty millimetre) nominal size foundation concrete1:4:8 (one cement :four sand : eight graded stone aggregate 40mm (fourty millimetre) nominal size inside plastering 15mm thick with cement mortar 1:3 (one cement three sand) finished with a floating coat of neat cement and making channels in concrete 1:2:4 mix (one cement : three sand : four graded stone aggregate 20mm (twenty millimetre) nominal size finished smooth complete including curing and testing Inside size 800 mm x 800 mm and 1000 mm (eight hundred millimetre into eight hundred millimetre and one thousand millimetre) deep including C.I cover with frame. (Light duty single seal pattern - 1) 455mmx610mm (four hundred fifty five millimetre into sx hundred ten millimetre) internal dimensions total weight of cover and frame to be not less than 38kg (thirty eight kilogram) (weight of cover 23 kg (twenty three kilogram) and weight of frane 15 kg (fifteen kilogram) With 300mm (three hundred millimetre) thick walls of squarred rubble masonry coursed with hard stones of approved quality in cement mortar 1:3 (one cement : three sand) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Suppliying cast iron cover without frame for manholes For frame of internal dimension 455mmx610mm (four hundred fifty five millimetre into six hundred ten millimetre) rectangular C.I. cover (light duty single seal pattern-1) the weight of cover to be not less than 23kg (twenty three kilogram) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

KDN Infrastructure Pvt. Ltd.