C/o Lok Bhawan Building at Kala-Amb, Tehsil Nahan, Sirmaur (HP)

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains in all heights and depths in all kinds of soil, including saturated soil comprising of pick work,jumper work and blasting work both in soft and hard rock with chiesling and wedging out of rock (where blasting is prohabited) and their intermediate classification of soil including dewatering whereever required,settling out to required lines,levels as shown on the drawing and directed by the Engineer in charge at site according to the HP.PWD specification of 1990 (one thousand nine hundred ninety) volume-I (one) and sorting out useful and unuseful material and transportation of the unuseful material for disposing at dumping site (to be arranged by the contractor) including payment of prescribed dumping charges of M.C. if levilled any to the satisfaction of the Engineer in charge through all modes of transporation including head load animal load or mechanical means alongwith its levelling, fine dressing and with all kinds of labour, mechineries, tools, equipment and safety measures and incidental necessary to complete the work by mechanical means and labour (if required). All useful material such as stones, shingles aggregate and slates shall be properly stacked at site to the maximum possible extent in all leads and lifts through all modes of transporation and used/removed as per the satisfaction of the Engineer in charge. any loss to the public and private properity during the course of execution and disposal of servicable and unservicable materials shall be the absolute responsiblity of the contractor and shall have to be duly compensated by him in all respects including all incidential charges and as directed by the Engineer in Charge:- All kinds of soil.

Filling available excavated earth ( excluding rock ) in trenches, plinth sides of foundations etc. in layers not exceeding 20cm ( twenty centimetre ) in depth, consolidating each deposited layer by ramming & watering including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Excavating, supplying & filling of local earth ( including roulaity ) by mechanical transport upto all leads, lifts also including ramming & watering of the earth in layers not exceeding 20 cm ( twenty centimetre ) in trenches, plinth, side of foundation etc. complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Supplying & filling in plinth with sand under floors including watering, ramming, consolidating & dressing complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and laying in position cement concrete of specified grade mechanically mixed and curing complete excluding the cost of centering and shuttering - All work up to plinth level and all floor level in 1:4:8 (one Cement : four coarse sand : eight graded stone aggregate 40mm (forty millimeter ) nominal size) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Making plinth protection 50 mm ( fifty milimetre ) thick of cement concrete 1 : 3 : 6 ( One cement : three coarse sand : six graded stone aggregate 20 mm ( twenty milimetre ) nominal size ) over 75 mm ( seventy five milimetre ) thick bed of dry brick ballast 40 mm ( forty milimetre ) nominal size, well rammed & consolidated & grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and laying in position cement concrete of specified grade mechanically mixed , vibrated & curing complete excluding the cost of centering, shuttering, finishing & reinforcement - All work up to plinth level and all floor level in 1:1.5 : 3 (One Cement : One & half coarse sand : five graded stone aggregate 20mm (twenty millimeter ) nominal size) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and laying reinforced cement concrete work in walls (any thickness), mechanically mixed, vibrated and curing complete including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor all level , excluding cost of centering, shuttering, finishing and reinforcement in 1:1.5:3 (one cement : one point five coarse sand : three graded stone aggregate 20mm ( twenty millimeter ) nominal size) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and laying reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor all level mechanically mixed, vibrated and curing complete, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (one cement : one point five coarse sand : three graded stone aggregate 20mm ( twenty millimeter ) nominal size) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing form work with steel plates 3.15mm ( three point fifteen millimeter ) thick welded with angle iron in frame 30X 30X5mm ( thirty X thirty X five millimeter ) so as to give a fair finish including centering ,shuttering, strutting and propping etc. with wooden battens and ballies , height of propping and centering below supporting floor to ceiling not exceeding 4.00 meters ( four meters ) and removal of the same for insitu- reinfoced concrete and plain concrete work including all leads and lifts of materials or as per the directions of Engineer in Charge.

Foundations, footings, bases of columns, etc. for mass concrete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Suspended floors, roofs, landings, balconies and access platform including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Lintels, beams, plinth beams, girders, bressumers and cantilevers including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Columns, Pillars, Piers, Abutments, Posts and Struts Circular including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Edges of slabs and breaks in floors and walls Under 20cm ( twenty centimeter ) wide including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and placing steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto floor all level. Thermo-Mechanically Treated bars of grade Fe-500 D or more including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation & plinth in all shapes and sizes in Cement mortar 1 : 6 ( One cement : six coarse sand ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor all level in all shapes and sizes in Cement mortar 1 : 6 (one cement : six coarse sand ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in : Cement mortar 1 :4 ( One cement : four coarse sand ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor all level in all shapes and sizes : Cement mortar 1 : 4 ( One cement : four coarse sand ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing 18 mm ( eighteen milimetre ) thick gang saw cut, mirror polished, premoulded & prepolished, machine cut for kitchen plateforms,vanity counters, window sills, facias & similar locations of required size, approved shade, colour & texture laid over 20 mm ( twenty milimetre ) thick base cement mortar 1 : 4 ( One cement : four coarse sand ), joints treated withwhite cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, coulding & polishing to edges to give high glass finish etc. complete at all level Granite of any colour, shade & all area of slab including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and laying Ceramic glazed wall tiles of size 300mm x 300 mm ( three hundred millimeter X three hundred millimeter )(thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except burgundy, bottle green, black of any size as approved by the Engineer-in-Charge in Skirting, risers of steps & dado over 12 mm ( twenty millimeter ) thick bed of cement mortar 1:3 (one Cement : three Coarse sand) and jointed with grey cement slurry @ 3.3kg/ sq.m (three point three zero kilograme per square meter ) including pointing in white cement mixed with pigment of matching shade complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing wood work in frames of doors, windows, clerestory windows & other framed, wrought framed & fixed in position with hold fast lugs or with dash fasteners of required dia & length (Hold fast lugs or dash fastener shall bepaid for separately ) 2nd class Dedodar wood, including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing 40 x 5 mm ( forty into five milimetre ) flat iron hold fast 40 cm ( Forty centimetre ) long including fixing to frame with 10 mm ( ten milimetre ) diametre bolts, nuts & wooden plugs & embedding in cement concrete block 30 x 10 x 15 cm ( thirty into ten into fifteen centimetre ) mix 1 : 3 : 6 ( One cement : three coarse sand : six graded stone aggregate 20 mm ( twenty milimetre ) nominal size ) including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing and fixing mild steel grills of required pattern in frames of steel & wood windows etc. with mild steel flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc. including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing panelled or panelled & glazed shutters for doors, windows & clerestory windows fixing with hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of the Engineer-in-Charge ( Butt hinges & necessary screws shall be paid separately ) Second class Deodar wood, 35 mm thick shutters, including all leads, lifts, carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing & fixing panelling or panelling & glazing in panelled & glazed shutters for doors, windows & clerestory windows ( Area of opening for poanel inserts excluding portion inside grooves or rebats to be measured ) panelling for panelled or panelled & glazed shutters 25 mm to 40 mm ( twenty five milimeter to forty milimeter )Particle Board 12mm ( twelve milimetre ) thick, thick pre-laminated partcle board with decorative lamination on one side & balancing lamination on other side, Grade-I, Type-II IS: 12823 marked, including all leads, lifts, carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing & fixing wooden moulded beading to door & windows frames with iron screws, plugs & priming coat on unexposed surface etc. complete second class teak wood 50 x 12 mm ( fifty into twelve milimetre ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing panelling or panelling & glazing in panelled & glazed shutters for doors, windows & clerestory windows ( Area of opening for poanel inserts excluding portion inside grooves or rebats to be measured ) panelling for panelled or panelled & glazed shutters 25 mm to 40 mm ( twenty five milimeter to forty milimeter ) 4 mm ( four milimetre ) thick glass pans ( weight not less than 10 Kg ( ten kilogram )per square metre ), including all leads, lifts, carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

Providing & fixing wire gauge shutters using galvanised mild steel gauge of average width of aperture 1.4 mm ( one point four milimetre ) in both directions with wire of dia 0.63 mm ( zero point six three milimetre ) for doors, windows & clerestory windows with hinges & necessary screws 35 mm ( thirty five milimetre ) thick shutters Kiln seasoned & chemically treated hallack wood including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium sliding door bolts, ISI marked anodised ( Anodic coating not less than grade AC 10 as per IS:1868 ), transparent or dyed colour to required colour or shade, with nuts & screws etc. complete 300 x 16 mm ( three hundred into sixteen milimetre ) size including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium sliding door bolts, ISI marked anodised ( Anodic coating not less than grade AC 10 as per IS:1868 ), transparent or dyed colour to required colour or shade, with nuts & screws etc. complete 250 x 16 mm ( two hundred fifty into sixteen milimetre ) size including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium tower bolts ISI marked anodised ( anodic coating not less than grade AC 10 as per IS;1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete 200 x 10 mm ( two hundred into ten milimetre ) size including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium tower bolts ISI marked anodised ( anodic coating not less than grade AC 10 as per IS;1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete 100 x 10 mm ( One hundred into ten milimetre ) size including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium handles ISI marked anodised ( anodic coating not less than grade AC 10 as per IS;1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete 125 mm ( one hundred twentyfive milimetre ) size including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium handles ISI marked anodised ( anodic coating not less than grade AC 10 as per IS;1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete 125 mm ( one hundred twenty five milimetre ) size including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium hanging floor stopper ISI marked anodic coating not less than grade AC 10 as per IS: 1868 ) transparent or dyed to required colour & shade, with necessary screws etc. complete Single rubber stopper including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium hanging floor stopper ISI marked anodic coating not less than grade AC 10 as per IS: 1868 ) transparent or dyed to required colour & shade, with necessary screws etc. complete Twin rubber stopper including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing aluminium die cast body tubular type universal hydraulic door closer ( having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 ( thirty five ) kilogram door with upto 700 ( seven hundred ) milimetre with necessary accessories & secews etc. complete,including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Structural steel work riveted, bolted or welded in built up sections, trusses & framed work,including cutting, hoisting, fixing in position & applying a priming coat of approved steel primer all complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing mild steel round holding down bolts with nuts & washers plates complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Cement concrete flooring 1 : 2 : 4 ( One cement : two coarse sand : four graded stone aggregate ) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete 40 mm ( forty milimetre ) thick with 20mm ( twenty milimetre ) nominal size ) stone aggregate including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & laying Mirror polished Kotah stone slab flooring over 20mm ( twenty milimeter ) ( average ) thick base laid over & jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing & polishing complete with base of cement mortar 1 : 4 ( One cement : four coarse sand ) 25 mm ( twenty five milimeter ) thick , including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & laying Mirror polished Kotah stone slab 20mm ( twenty milimeter ) thick in risers of steps, skirting, dado & pillars laid on 12 mm ( twelve milimeter ) ( average ) thick cement mortar 1 : 3 ( One cement : three coarse sand ) & jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing & polishing complete , including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & laying ceramic glazed floor tiles of size 300x300cm ( Three hundred into three hundred milimetre ) ( thickness to be specified by the manufacturer ) of Ist quality conforming to IS: 15622 of approved make in all colour , laid on 20 mm ( twenty milimetre ) thick cement mortar 1 : 4 ( One cement : four coarse sand ), jointing with grey cement slurry @ 3.3 Kg ( at the rate three point three kilogram ) per square metre including pointing the joints with white cement and matching pigment etc., complete, including all leads,lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge

Providing & fixing Garsa stone 12 mm ( twelve milimetre ) cladding on Reinforced cement concrete surface side as on faces of Arch masonry walls etc. on 12 mm ( twelve milimetre) thick cement plaster 1 : 3 ( one cement : three coarse sand ) & jointed with cement slurry including scaffolding etc. complete including all leads, lifts & carriage of materials and to the entire satuisfaction of the Engineer-in-Charge

Providing and fixing on wall face PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm ( ten millimeter ) gap for thermal expansion, Single socketed pipes complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:- 110mm ( One hundred ten millimeter ) diameter metre.

Providing and fixing on wall face PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm ( ten millimeter ) gap for thermal expansion complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:- Bend 87.5° 110mm ( eighty seven point five degree one hundred ten millimeter ) bend.

Providing and fixing on wall face PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm ( ten millimeter ) gap for thermal expansion complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:- Shoe ( Plain )110mm ( One hundred ten millimeter ) shoe.

Providing & fixing mild steel holder bat clamps of approved design to cast iron or S.C.I. rain water pipes embedded in and including cement concrete blocks 10 x 10 x 10 cm of 1 : 2 : 4 mix ( One cement : two coarse sand : four graded stone aggregate 20 mm nominal size ) & cost of cutting holes & making good the wall etc. 110 mm ( One hundred ten milmetre ) diameter PVC pipe including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Providing & fixing 0.60mm ( Zero point six zero milimeter ) thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster ( RNP ) organic coating of 20 ( twenty ) microns over 5 ( Five ) microns primer coating to back coat of ployster of 5 ( five ) microns over 5 microns primer coating including fixing with prepainted iron-J or L hooks bolts and nuts 6mm dia metre with prepainted limpet & rubber washers complete with all accessories as required as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts and other incidental charges complete as per entire satisfaction of the Engineer-in Charge.

Providing & fixing ridge or hips 60cm ( Sixty centimetre ) overall with 0.60mm ( Zero point six zero milimetre ) thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster ( RNP ) organic coating of 20 ( twenty ) microns over 5 ( five ) microns primer coating Plus back coat of ployster of 5 ( five ) microns over 5 ( five ) microns primer coating including fixing with prepainted iron-J or L hooks bolts & nuts 6mm ( Six milimetre ) dia & prepainted G.I. limpet and bitumen washers complete with all accessories as required as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts and other incidental charges complete as per entire satisfaction of the Engineer-in Charge.

Providing & fixing valley 60cm ( Sixty centimetre ) overall with 0.60mm ( Zero point six zero milimetre ) thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 ( Five ) microns over 5 ( five ) microns primer coating including fixing with prepainted iron-J or L hooks bolts & nuts 6mm ( Six milimetre ) dia with prepainted G.I. limpet and bitumen washers complete with all accessories as required as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts and other incidental charges complete as per entire satisfaction of the Engineer-in Charge.

Providing & fixing 30 cm ( thirty centimetre ) wide and minimum 120cm ( ninety centimetre ) overall box type prepainted steel sheet gutter with iron bracket 40x3mm ( Forty into three milimetre ) size, bolts & nuts and washers etc. including making necessary connections with rain water pipes complete as per design 0.63mm ( Zero point six three milimetre ) thick as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts and other incidental charges complete as per entire satisfaction of the Engineer-in Charge.

Providing & fixing mild steel B.P. sheet 1.66 mm to 2 mm ( One point six six milimetre to two milimetre ) thick in eaves board/ facia/ soffits/ ceiling including cutting, fixing & welding to steel roof members & applying a coat of red lead primer complete as per the instruction of Engineer-in-Charge ( Base member of steel work shall be measured & paid for separately ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing flat iron bracket 50 x 3 mm ( Fifty into three milimetre ) size with necessary bolts, nuts & washers etc. for fixing galvanised steel sheets gutters with purlins including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & fixing false ceiling at all height including providing & fixing of frame work made of special sections, power pressed from mild steel sheets & galvanised with zinc coating of 120 ( one hundred twenty ) gramme per square metre ( both side inclusive ) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6mm ( twenty five milimeter into one point six milimetre ) thick with flanges of 27 mm and 37 mm, at 1200 mm ( twenty seven milimetre, thirty seven milimetre , at 0ne thousnd two hundred milimetre ) centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm ( Twelve point five milimetre dia into fifty milimetre ) long with 6 mm ( six milimetre ) dia bolts, other flange of cleat fixed to the angle hangers of 25 x 10 x 0.50 mm( twenty five into ten into zero point five zero milimetre ) of required length with nuts & bolts of required size & other end of angle hanger fixed with intermediate galvanised iron channels 45x15x0.90mm ( forty five into fifteen into zero point nine zero milimetre ) running at the spacing of 1200mm ( One thousand two hundred milimetre ) centre to centre, to which the ceiling section 0.5 mm ( zero point five milimere ) thick bottom wedge of 80 mm ( eighty milimetre ) with tapered flanges of 26 mm ( twenty six milimetre ) each having lips of 10.5 mm, at 450mm ( ten point five milimetre, at four hundred fifty milimetre ) centre to centre, shall be fixed in a direction perpendicular to galvanised iron intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm ( two point six four milimetre dia into two hundred thirty milimetre ) long galvanised iron wire at every junction, including fixing perimeter channel 0.5mm ( zero point five milimetre ) thick 27mm ( twenty seven milimetre ) high having flanges of 20 mm and 30 mm ( twenty milimetre & thirty milimetre ) long,the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm ( twenty five milimetre ) long dry wall screws @ 230 mm ( at the two hundred thirty milimetre ) interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm ( three point five into twenty five milimetre at two hundred thirty milimetre ) centre to centre, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes finishing with jointing compound in three layers covering upto 150 mm ( one hundred fifty milimetre ) on both sides of joint & two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawing, specification & direction of the Engineer-in-Charge but excluding the cost of painting with ACP ( Aluminium Composite sheel panel ) Fibre cement board 6 mm ( six milimetre ) flase ceiling 60 x 60 cm ( sixty into sixty centimetre ) complete in all respect,including all leads, lifts & carriage of materials & to the entire satisfaction of the Engineer-in-Charge.

15mm ( fifteen millimeter ) cement plaster on the rough side of single or half brick wall of mix : 1:4 (one cement: four fine sand) complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

15mm ( fifteen millimeter ) cement plaster on the rough side of single or half brick wall of mix : 1:6 (one cement: six fine sand) complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing & applying plaster of pais putty of 2mm ( two milimeter ) thickness over plastered surface to prepare the surface even & smooth complete, including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Distempering with oil bound washable distemper of approved brand & manufacture to give an even shade new work ( two or more coats ) over and including water thinnable priming coat with cement primer including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Finishing walls with Acrylic smooth exterior paint with of required shade new work ( two or more coat ) applied @ 1.67 litre/10 Sqmt ( one point six seven litre per ten square metres ) over & including priming coat of exterior primer applied @ 2.20 Kg /10 Sqmt ( at the rate two point two zero kilograme per ten square metre ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10sqm ( zero point nine zero litre per ten square meter ) over an under coat of primer applied @0.75 ltr/10 sqm ( zero point seven five litre per ten square meter )of approved brand and manufacture complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10sqm( zero point nine zero litre per ten square meter ) over an under coat of primer applied @ 0.80 ltr/ 10sqm( zero point eight zero litre per ten square meter ) of approved brand and manufacture complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm ( one hundred millimeter ) sand cast Iron P or S trap, 10 litre ( ten litre ) low level white PVC flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge: White Vitreous china Orissa pattern W.C. pan of size 580mm x 450mm ( five hundred eighty millimetre into four hundred fifty millimeter ) with integral type foot rests.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10litre ( ten litre )low level white PVC flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:- W.C. pan with ISI marked white solid plastic seat.

Providing and fixing white vitreous china flat back large urinal of size 630mm x 395mm x 420mm ( Six hundred thirty millimeter X three hundred ninety five millimeter X four hundred twenty millimeter ) with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge :- Single half stall urinal with 5 litre ( five litre ) P.V.C. automatic flushing cistern.

Providing and fixing wash basin with C.I. brackets, 15mm ( fifteen millimeter ) C.P. brass pillar taps, 32mm ( thirty two millimeter ) C.P.brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:- White Vitreous China wash basin size 550mm x 400mm ( five hundred fifty millimeter into four hundred millimeter ) with single 15mm ( fifteen millimeter ) C.P. Brass pillar tap .

Providing & fixing stainless steel A ISI 304 ( 18/8 ) kitchen sink as per IS: 13983 with cast iron brackets and stainless steel plug 40 mm ( forty milimeter ) including painting of fittings & brackets, cutting & making good the walls wherever required kitchen sink with drain board 460 x 560 mm ( four hundred sixty into five hundred sixty milimeter ) bowl depth 229 mm ( two hundred twenty nine milimeter ), including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and fixing 600mm x 450mm ( Six hundred millimeter into four hundred fifty millimeter ) beveled edge mirror of superior glass (of approved quality) complete with 6mm ( six milimetre ) thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and fixing 600mm x 120mm x 5mm ( Six hundred millimeter into one hundred twenty millimeter into five millimeter ) glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40mm ( forty millimeter ) long screws, rawl plugs etc., complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providuing & fixing PTMT towel rail complete with brackets fixed to wooden cleats with C.P. brass screws with concealed fittings arrangement of approved quality & colour, 450 mm ( Four hundred fifty milimetre ) long towel rail with total length of 495 mm, 78 mm ( Four hundred ninety five milimeter, seventy eight milimetre ) wide & effective height of 88 mm ( eighty eight milimetre ) , weighting not less than 170 ( One hundred seventy ) grams including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and fixing Polyethelene-AluminiumPolyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre ( one metre ) spacing. This includes testing of joints complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:- 1216 (16 mm ( sixteen millimeter ) OD) pipe.

Providing and fixing Polyethelene-AluminiumPolyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre ( one metre ) spacing. This includes testing of joints complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:-1620 (20mm ( twenty millimeter ) OD) pipe.

Providing and fixing G.I. pipes complete with G.I. fittings & Clamps including making good the walls etc. concealed pipe including painting with anti corrosive bitumastic paint, cutting & making good the walls including carriage of materials in all leads and lifts and as directed by the Engineer in Charge. internal work:-15mm ( fifteen millimeter ) dia nominal bore.

Providing and fixing G.I. pipes complete with G.I. fittings including making good the walls etc. concealed pipe including painting with anti corrosive bitumastic paint, cutting & making good the walls including carriage of materials in all leads and lifts and as directed by the Engineer in Charge. internal work :- 20mm ( twenty millimetre ) dia.

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:- 25 mm to 40mm ( twenty five millimeter to forty millimeter ) nominal bore.

Fixing water meter & stop cock in G.I. pipe line including cutting & threading the pipe & making long screws etc. complete ( Cost of water meter & stop cock to be paid separately ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS : 8931, complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge. 15mm( fifteen millimeter ) nominal bore .

Providing and fixing C.P. brass stop cock ( Concealed ) of standard design & of approved make conforming to IS : 8931, complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge. 15mm( fifteen millimeter ) nominal bore .

Providing and fixing C.P. brass angle valve for basin mixer & geyser point of approved quality conforming to IS : 8931, complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge. 15mm( fifteen millimeter ) nominal bore .

Providing & fixing C.P. brass extension nipple ( size 15 mm x 50 mm ( fifteen milimetre into fifty milimetre ) of approved make & quality as per direction of Engineer-in-Charge including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Constructing brick masonry manhole in cement mortar 1:4 ( one cement : four coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (one cement : one point five coarse sand (zone- III) : three graded stone aggregate 20mm ( twenty millimeter ) nominal size), foundation concrete 1:4:8 mix (one cement : four coarse sand (zone- III) : eight graded stone aggregate 40mm ( forty millimeter ) nominal size), inside plastering 12mm ( twelve millimeter ) thick with cement mortar 1:3 (one cement : three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement : two coarse sand : four graded stone aggregate 20mm ( twenty millimeter ) nominal size) finished with a floating coat of neat cement complete as per standard design complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge. : Inside size 90cm x 80cm and 45cm ( Ninety centimeter into eighty centimeter and forty five centimeter ) deep including C.I. cover with frame (medium duty) 455 x 610 mm ( Four hundred fifty five into Six hundred ten millimeter ) internal dimensions, total weight of cover and frame to be not less than 38 kg ( thirty eight kilogram ) (weight of cover 23 kg ( twenty three kilogram ) and weight of frame 15 kg( fifteen kilogram ) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.50.

Providing and fixing high pressure PVC spigot & socket, waste & ventilating pipes ISI marked including fixing with approved adhesive etc. complete. :-

110mm (One hundred ten milimetre ) dia as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

75mm ( Seventy five milimetre ) dia as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing PVC door bend with oval access door insertion rubber washers 3mm ( three milimeter ) thick bolts & nuts ISI marked complete including fixing with approved adhesive etc. complete.

110mm (One hundred ten milimetre ) dia as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

75mm ( Seventy five milimetre ) dia as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing PVC collars ISI marked including fixing with approved adhesive etc. complete

110mm (One hundred ten milimetre ) dia as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

75mm ( Seventy five milimetre ) dia as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing PVC Plain bend ISI marked including fixing with approved adhesive etc. complete

100mm (One hundred milimetre ) dia as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

75mm ( Seventy five milimetre ) dia as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing PVC double equal branch with oval access door insertion rubber washers 3mm ( three milimeter ) thick bolts & nuts ISI marked complete including fixing with approved adhesive etc. complete

100mm (One hundred milimetre ) dia as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

75mm ( Seventy five milimetre ) dia as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing PVC clamps ISI marked including fixing with approved adhesive etc. complete

100mm (One hundred milimetre ) dia as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

75mm ( Seventy five milimetre ) dia as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing PVC reducer ISI marked including jointing with approved ahesive etc. complete

150mm x 110mm (One hundred fifty milimetre into one hundred ten milimeter ) dia as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

110mm x 75mm (One hundred ten milimetre into Seventy five milimeter ) dia as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing cast iron floor trap of self cleaning design with sand cast iron screwed down or hinged grating without vent arm complete including cost of cutting & making good the walls & floors :-

110mm x 90mm ( One hundred ten milimetre into ninety milimeter ) dia as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

110mm x 75mm (One hundred ten milimetre into Seventy five milimeter ) dia as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing in position precast reinforcement coment concrete manhole cover & frame of required shape & approved quality LD- 2.5 ( Two point five ) rectangular shape 600 x 450 mm ( six hundred into four hundred fifty milimetre ) internal dimensions including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Providing & fixing in position precast reinforcement coment concrete manhole cover & frame of required shape & approved quality LD- 2.5 ( Two point five ) square shape 450 mm ( four hundred fifty milimetre ) internal dimensions including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Supplying & filling brick bats in dispension trenches ( Brick aggregate ( Single size ) 50 mm ( Fifty milimetre ) nominal size ) including carriage of materials in all leads and lifts and as directed by the Engineer in Charge

Providing and fixing on wall face PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm ( ten millimeter ) gap for thermal expansion, Single socketed pipes complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:- 75 mm ( Seventy five millimeter ) diameter metre.

Providing and fixing on wall face PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm ( ten millimeter ) gap for thermal expansion complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge:- Bend 87.5° 75 mm ( eighty seven point five degree Seventy five millimeter ) bend.

imIMRAN SHAH

Pratap Singh