Source strengthening for Heritage village Pragpur and its adjoining area in Sub Tehsil Pragpur District Kangra (HP)

Amount

Excavation in foundation trenches etc. in earth work in all kinds of soil such as pick work, jumper work, blasting in soft and hard rock and chiselling work including saturated soil slushy soil and under floor upto all depth and stacking the excavated soil not more than 3 metre clear from the edge of excavation and then returning the stacked soil in 15 centimetre (Fifteen centimetre) layer when required into plinth sides of foundation etc.consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed by the Engineer-in-charge within all leads and lifts.

Laying jointing and testing in trenches to level or grade of G.I. pipe of following dia confirming to ISI 1239-1990 (part-III) having wall thickness as specfied below capable of with standing required test pressure including manufacturing and fabrication of reducers/tapers all short pieces required degree of bends etc. as per site requirement made from parent tubes earth work in trenches (MS flanged of required table shall be measured and paid seperately) including welding of flanges joints of pipe duly welded including nuts, bolts & gasket separately). the welding electrodes shall be as per IS: 1369-1967 of Advani oerlikon/L&T of ISI marked make the damaged portion of pipes (if damages during laying and joints operation of pipe). The rates also including entire carriage of material flushing cleaning and hydraulic testing of pipes D.P. test of butt welded joints complete in all respect and to the best satisfaction and direction of Engineer-in-Charge complete within all leads and lifts. Booster Stage Rising Main 1 100 milimetre dia (M) WT - 4.50 mm RD 0 to 120 = 120 Rmt.

100 milimetre dia (M) WT - 4.50 mm RD 120 to 360 = 240 Rmt.

100 milimetre dia (M) WT - 4.50 mm RD 360 to 950 = 590 Rmt.

Booster Stage Rising Main 2 100 milimetre dia (M) WT - 4.50 mm RD 0 to 120 = 120 Rmt.

100 milimetre dia (M) WT - 4.50 mm RD 120 to 480 = 360 Rmt.

100 milimetre dia (M) WT - 4.50 mm RD 480 to 780 = 300 Rmt.

Ist Stage Rising Main 150 milimetre dia (H) WT - 5.40 mm RD 5670 to 7290 = 1620 Rmt.

150 milimetre dia (M) WT - 4.80 mm RD 7290 to 10250 = 2960 Rmt.

Providing laying jointing and testing of bevelled ended MSERW zinc coated pipe of following diametre and wall thickness confirming to IS/ISO 3183-2012 of steel grade L-290 A (latest with upto date ammendments) and capable of with standing required test pressure in a rendom length of 5.5 to 6.5 mtr., including manufacturing and fabrication of reducers/tapers all short pieces, required degree bends etc. as per site requirement made from parent tubes complete in all respect to the best satisfaction and direction of Engineer-in-Charge. The fabricated bends shall have three or four cuts having its radius not less than five times of the dia of pipe. Pipe shall be factory galvenised (Zinc coated both in side and out side) as per relevant IS standard and the damaged portion of the pipe complete in all respect and to the best satisfaction and direction of Engineer-in-Charge within all leads and lifts. Make of pipe TATA/JINDAL/SURYA ROSHNI (Earth work in trenches, Providing & welding of flanges and butt welding shall be measured and paid for seperately) 150 milimetre dia (MSERW) WT - 4.8mm RD 0 to 1620

150 milimetre dia (MSERW) WT - 4.80mm RD 1620 to 5670

Providing welding and fixing of M.S. flanges @6% of flanged joints conforming to following tables as per IS 6392-1971 (Latest with up to date amendments) and welding of MS flanges with GI/MSERW pipes in required layers on both faces i.e two layer on outer faces and one layer on inner faces to make the joint leak proof (The cost of providing and laying of GI/MSERW pipes and butt welding joints to be measured and paid for separtely). The welding of flanges should conform to IS 816-1969 with electrodes as per IS: 814-1991 and required number of nuts and bolts conforming to IS 1364, the thicthness of gasket not less than 3.00 mm conforming to IS 2712-1998. The work shall be done as per entire satisfaction of Engineer in charge with in all leads and lifts. Booster Stage Rising Main 1 100 milimetre dia (M) with Flange Table - 28 RD 0 to 120 = 120 Rmt.

100 milimetre dia (M) with Flange Table - 17 RD 120 to 360 = 240 Rmt.

100 milimetre dia (M) with Flange Table - 5 RD 360 to 950 = 590 Rmt.

Booster Stage Rising Main 2 100 milimetre dia (M) with Flange Table - 28 RD 0 to 120 = 120 Rmt.

100 milimetre dia (M) with Flange Table - 17 RD 120 to 480 = 360 Rmt.

100 milimetre dia (M) with Flange Table - 5 RD 480 to 780 = 300 Rmt.

Ist Stage Rising Main 150 milimetre dia (MSERW) with Flange Table 34 RD 0 to 1620

150 milimetre dia (MSERW) with Flange Table - 28 RD 1620 to 5670

150milimetre dia GI Pipe(H) with Flange Table - 28 RD 5670 to 7290 = 1620 Rmt.

150milimetre dia GI Pipe(M) with Flange Table - 17 RD 7290 to 10250 = 2960 Rmt.

Supply and errection of Kirloskar/Kilburn/IVC/Fouress/Gled/BHEL/Leader make Cast steel double flanged swing check type reflux valve of class ASA-300 confirming to BS 1868(API-600) (latest edition) having bye pass arrangement equal to dia of Rising main and shall be suitable for withstanding nominal seat pressure of 52 kg/cm². 150 milimetre dia.

Supply and errection of Kirloskar/Kilburn/IVC/Fouress/Gled/BHEL/Leader make Cast steel double flanged swing check type reflux valve of class ASA-300 confirming to BS 1868(API-600) (latest edition) having bye pass arrangement equal to dia of Rising main and shall be suitable for withstanding nominal seat pressure of 52 kg/cm². 100 milimetre dia.

Booster stage : Rising main 1 Supply/errection and Commisning of submersible pumping set of (KSB/Kalama/Kirloskar/Johnston/Cromption/BS) make conforming to BIS; 8034-1976 latest suitable for lifting clear water (latest with uptodate ammendments) fitted with bronze impellers/suitable alloy directly coupled to squirrell case electric induction motor of same make as (manufacurer standard) conforming to BIS; 9283-1979 (latest with uptodate ammendment ) and totally water proof for submersible duty, isolated from the pump by intermediate casing with double mechanical seal in oil chamber, grease packed lubricated bearings & provided with stainless steel thrust bearing plate to with stand vertical loads with minimum wear & tear. It should also be fitted with a device to take up expansion of water with the heating of motor including water level guard,errection clamps, cable clips & depth gauge etc. The pump shall be suitable for operation on data given below (1 Working and 1 No. Stand by):- ( i) Total Head 181.19 Metre (ii) Discharge required from each pump. 7.42 LPS (iii) No. of pump required 1.00 Nos. (iv) Location of the site of installation of machinery. The site is located at a distance of 18 Kmts from Pragpur & 100 mtr. Head Load (v) The Altitude of installation. The altitude of place is 433.5 mtrs above MSL (vi) Type of current. AC three phase supply with freqduency of 50 cycle per second. (vii) Rate Voltage 415+ 10% (viii) Type of water and its source Clear cold water (ix) Charactristics of water. Clear Water (a) Ambient Temperature dig.c 20 dig. C (b) Turbidity NTU (c) Hardness260Mg/Ltrs(as CaCO3) - (d) PH 7.5 - (e) total solid Mg /Ltrs - (f) Other - (x) Depth of T/Well - mtrs. (xi) LWL in Collcetion tank - mtrs. (xii) Dia of Bore - mtrs. (xiii) Max draw down - (xiv) Static water level - mtrs. (xv) Center line level of Pump - mtrs. (xvi) Discharge level of highest point 500 mtrs. (xvii) Static head in Metres 150.00 (xviii) Length of R/Main (Including Column Assembly) 950 Metres (xix) Dia of Rising main 100 mm dia (xx) No of working hours per day 8 Hours (xxi) Limit of pump operation. (-) 15 % (+) 10% of total head (xxii) R.P.M. of pumping set. RPM ( or to be specified by the tenderer) (xxiii) Test run 16 Hours continueously for 7 days

Supply, Installation, Testing and Commissioning of star delta starter panel for centrifugal pump made out of 16 Gauge sheet, powder coated dust and vermin proof wall/base mounted and front opening door type with copper insulated wiring suitable to operate 2 Nos. pump(1 working and i standby) of the reating 20.00 HP through Star Delta Starter Mechanism starter should be capable enough to handle the following faults like short circuit, over current , under current, over voltage, under voltage, dry run protection and phase loss with LED ON/OFF & TRIP indicator of JSV approved make 8.1 Star, Delta and Main Power Contactors of required ratings as per type-2 co-ordination for starter = 2 set 8.2 Voltage protection device to protect panel from over voltage and under voltage = 2 Number 8.3 Single phasing and phase reversal protection device to safeguard system from single phasing and phase reversal of the supply voltage = 2 Number 8.4 Multi function meter indicating different parameters like current, voltage, KWH, PF, THD, etc. with Rs. 485 communication JSV approved make = 1 Number 8.5 Main incomer MCCB/MCB of suitble capacity of L&T/ Schneider/ABB make on the feeder for pumping set confirming to BIS2516-1985 (Letest edition) = 1 Number 8.6 Individual starter ncomer MCCB/MCB of suitble capacity of L&T/ Schneider/ABB make on the feeder of pumping set confirming to BIS2516-1985 (Letest edition) = 2 Set 8.7 Three phase indicating lamps complete with logged switches for individual motors conforming to BIS 3452 (Part I & II) latest with up to date amendments = 1 Set 8.8 LED On/Off & trip indicator and push buttons, Control and power wiring, Power capacitor, Cooling fan 230 VAC , Control terminal Bus Bar, i.e. Bolt, insulator etc. = 2 Number 8.9 Surge suppressor divice with isolating MCCB to eliminate the power surges due to lightening and system surges = 1 Number 8.10 Control Transformer to provide a stable control voltage to safeguarg the control circuit of all the components from the voltage surges and spikes = 1 Number

Supply of Kirloskar/Kilburn/IVC/Fouress/Gled/BHEL/Leader make Cast steel double flanged sluice valve of class ASA-300 confirming to BIS-1414(API-600) (to be provided on delivery side) of equal size to one dia more than the dia of delivery of pump and capable of with standing nominal seat test pressure of 52 kg/cm². NOTE :- The cast iron Sluice valve shall conform to BIS-780-1984 for 50 mm to 300 mm dia and BIS:2906-1984 for 350 mm to 1200 mm dia (latest eddition). However if seat pressure exceeds the limits prescribed in above mentioned BIS then it shall be of cast steel conforming to class ASA-150 for seat pressure up to 21 Kg./Cm2 & of class ASA-300 for seat pressure 52 Kg./Cm2 as per BS-1414 (API-600).

Supply of Kirloskar/Kilburn/IVC/Fouress/Gled/BHEL/Leader make Cast steel double flanged swing check type reflux valve having bypass arrangement of class ASA-300 confirming to BS 1868(API-600) (latest edition)to be provided on delivery side) of size one step higher than the delivery size of pump and shall be suitable for withstanding nominal seat pressure of 52 kg/cm².

Supply of Kirloskar/Kilburn/IVC/Fouress/Gled/BHEL/Leader make Cast iron double flanged swing check type reflux valve having bypass arrangement of class ASA-300 confirming to BS 1868(API-600) (latest edition)to be provided on Rising main) and shall be suitable for withstanding nominal seat pressure of 52 kg/cm². NOTE :- The reflux valve shall conform to BIS-5312-1984 (part-I) latest with upt date ammendments. However if seat pressure exceeds the limits prescribed in BIS 5312 then the reflux valves shall be of cast steel conformingt to class ASA-150 for seat pressure up to 21 Kg./Cm2 & of class ASA-300 for seat pressure 52 Kg./Cm2 as per BS-1414 (API-600).

Providing & laying PVC insulated jointless, flat water proof copper cable of Siemens/Finolex/Grandlay/Gloster make conforming to BIS:1554 (Part I) -1988 or latest with up to date ammendments of suitable size for the pump sets offered(one cable carrying all three phases) including all other electrical equipment /accessories such as thimbles, flexible pipe, solder, nuts & bolts cable glands etc. laid in pipes or trenches under floor. The type, size & make will be subject to approval of HPSEB authorities.In case of non acceptance by HPSEB authorities it shall have to be replaced by the tenderer free of cost. On supply side of 3½ core coper cable 10.00 mm^2 ( From HPSEB Meter to Switch &Starter).

On motor side 3 core flat joint less copper cable of size 6.00 mm^2 ( From Switch & Starter to Motor) pump installed in the bore.

Supply & errection of floor power shunt capacitor conforming to BIS 2834-1986 latest with upto date ammendments of GEC/Siemen/ Havells L&T make to raise the prevailing power factor at site to 0.95 for direct connection to induction motor individually of requirement KVAR according to BHP of motor offered including cable Siemens/Gloster/ICC make from busbar chamber to capacitor & also including Standard/ L&T/Kilburn/Indo asian make ICTP switches conforming to BIS 4064- 4064-1978 or latest with HRC fuses.

Supply of standarad make 100 mm dia circular/square dial pressure gauge of suitable range Fiebeg/Bourden/ Precision make with all accessories such as stop cock, copper tubing etc. conforming to BIS 3624-1987 latest with up to date ammendments.

P/Laying Column assembly of G.I./MSERW pipe considering site requirements and having appropriate size in accordance with the delivery size of pumping set . The pipe shall conform to relevant BIS codes & capable of with standing the feild test pressure equal to 1.5 times the operating pressure including all type of fittings such as bends, tapers/ reducers, flanges, rubber gaskets 3mmthick, nuts & bolts and any other fitting required at site and work shall be to the entire satisfaction of Engineer-in-Charge. Column assembly = 80mm dia G.I.flanged pipe (medium grade) NOTE:- Actual laying to be done as per final drawings to be approved by the Engineer in charge

Errection of all equipments including the cost of tees, bends tapers & any other fittings required as per site conditions & as per directions of Engineer-in-Charge.

Booster stage : Rising main 2 Supply/errection and Commisning of submersible pumping set of (KSB/Kalama/Kirloskar/Johnston/Cromption/BS) make conforming to BIS; 8034-1976 latest suitable for lifting clear water (latest with uptodate ammendments) fitted with bronze impellers/suitable alloy directly coupled to squirrell case electric induction motor of same make as (manufacurer standard) conforming to BIS; 9283-1979 (latest with uptodate ammendments) and totally water proof for submersible duty, isolated from the pump by intermediate casing with double mechanical seal in oil chamber, grease packed lubricated bearings & provided with stainless steel thrust bearing plate to with stand vertical loads with minimum wear & tear. It should also be fitted with a device to take up expansion of water with the heating of motor including water level guard,errection clamps, cable clips & depth gauge etc. The pump shall be suitable for operation on data given below:- (i ) Total Head 198.00 Metre (ii) Discharge required from each pump. 7.42 LPS (iii) No. of pump required 1.00 Nos. (iv) Location of the site of installation of machinery. The site is located at a distance of 18 Kmts from Pragpur & 100 mtr. Head Load (v) The Altitude of installation. The altitude of place is 433.5 mtrs above MSL (vi) Type of current. AC three phase supply with freqduency of 50 cycle per second. (vii) Rate Voltage 415+ 10% (viii) Type of water and its source Clear cold water (ix) Charactristics of water. Clear Water (a) Ambient Temperature dig.c 20 dig. C (b) Turbidity NTU (c) Hardness260Mg/Ltrs(as CaCO3) (d) PH 7.5 - (e) total solid Mg /Ltrs - (f) Other - (x) Depth of T/Well - mtrs. (xi) LWL in Collcetion tank - mtrs. (xii)Dia of Bore - mtrs. (xiii) Max draw down - (xiv) Static water level - mtrs. (xv) Center line level of Pump - mtrs. (xvi) Discharge level of highest point 500 mtrs. (xvii) Static head in Metres 170.00 (xviii) Length of R/Main (Including Column Assembly) 780 Metres (xix) Dia of Rising main 100 mm dia (xx) No of working hours per day 8 Hours (xxi) Limit of pump operation. (-) 15 % (+) 10% of total head (xxii) R.P.M. of pumping set. RPM ( or to be specified by the tenderer) (xxiii) Test run 16 Hours continueously for 7 days

Supply, Installation, Testing and Commissioning of star delta starter panel for centrifugal pump made out of 16 Gauge sheet, powder coated dust and vermin proof wall/base mounted and front opening door type with copper insulated wiring suitable to operate 2 Nos. pump(1 working and i standby) of the reating 20.00 HP through Star Delta Starter Mechanism starter should be capable enough to handle the following faults like short circuit, over current , under current, over voltage, under voltage, dry run protection and phase loss with LED ON/OFF & TRIP indicator make Aarmation Electric Private Limited/MAS/ELLES/Adlec/L&T indicators 18.1 Star, Delta and Main Power Contactors of required ratings as per type-2 co-ordination for starter = 2 Set 18.2 Voltage protection device to protect panel from over voltage and under voltage = 2 Number 18.3 Single phasing and phase reversal protection device to safeguard system from single phasing and phase reversal of the supply voltage = 2 Number 18.4 Multi function meter indicating different parameters like current, voltage, KWH, PF, THD, etc. with Rs. 485 communication make Aarmaation/ L&T /Schneider/Siemens = 1 Number 18.5 Main incomer MCCB/MCB of suitble capacity of L&T/ Schneider/ABB make on the feeder for pumping set confirming to BIS2516-1985 (Letest edition) = 1 Number 18.6 Individual starter ncomer MCCB/MCB of suitble capacity of L&T/ Schneider/ABB make on the feeder of pumping set confirming to BIS2516-1985 (Letest edition) = 2 Set 18.7 Three phase indicating lamps complete with logged switches for individual motors conforming to BIS 3452 (Part I & II) latest with up to date amendments = 1 Set 18.8 LED On/Off & trip indicator and push buttons, Control and power wiring, Power capacitor, Cooling fan 230 VAC , Control terminal Bus Bar, i.e. Bolt, insulator etc. = 2 Number 18.9 Surge suppressor divice with isolating MCCB to eliminate the power surges due to lightening and system surges = 1 Number 18.10 Control Transformer to provide a stable control voltage to safeguarg the control circuit of all the components from the voltage surges and spikes = 1 Number

Supply of Kirloskar/Kilburn/IVC/Fouress/Gled/BHEL/Leader make Cast steel double flanged sluice valve of class ASA-300 confirming to BIS-1414(API-600) (to be provided on delivery side) of equal size to one dia more than the dia of delivery of pump and capable of with standing nominal seat test pressure of 52 kg/cm². NOTE :- The cast iron Sluice valve shall conform to BIS-780-1984 for 50 mm to 300 mm dia and BIS:2906-1984 for 350 mm to 1200 mm dia (latest eddition). However if seat pressure exceeds the limits prescribed in above mentioned BIS then it shall be of cast steel conforming to class ASA-150 for seat pressure up to 21 Kg./Cm2 & of class ASA-300 for seat pressure 52 Kg./Cm2 as per BS-1414 (API-600).

Supply of Kirloskar/Kilburn/IVC/Fouress/Gled/BHEL/Leader make Cast steel double flanged swing check type reflux valve having bypass arrangement of class ASA-300 confirming to BS 1868(API-600) (latest edition)to be provided on delivery side) of size one step higher than the delivery size of pump and shall be suitable for withstanding nominal seat pressure of 52 kg/cm².

Supply of Kirloskar/Kilburn/IVC/Fouress/Gled/BHEL/Leader make Cast iron double flanged swing check type reflux valve having bypass arrangement of class ASA-300 confirming to BS 1868(API-600) (latest edition)to be provided on Rising main) and shall be suitable for withstanding nominal seat pressure of 52 kg/cm². NOTE :- The reflux valve shall conform to BIS-5312-1984 (part-I) latest with upt date ammendments. However if seat pressure exceeds the limits prescribed in BIS 5312 then the reflux valves shall be of cast steel conformingt to class ASA-150 for seat pressure up to 21 Kg./Cm2 & of class ASA-300 for seat pressure 52 Kg./Cm2 as per BS-1414 (API-600).

Providing & laying PVC insulated jointless, flat water proof copper cable of Siemens/Finolex/Grandlay/Gloster make conforming to BIS:1554 (Part I) -1988 or latest with up to date ammendments of suitable size for the pump sets offered(one cable carrying all three phases) including all other electrical equipment /accessories such as thimbles, flexible pipe, solder, nuts & bolts cable glands etc. laid in pipes or trenches under floor. The type, size & make will be subject to approval of HPSEB authorities.In case of non acceptance by HPSEB authorities it shall have to be replaced by the tenderer free of cost. On supply side of 3½ core coper cable 10.00 mm^2 ( From HPSEB Meter to Switch &Starter).

On motor side 3 core flat joint less copper cable of size 6.00 mm^2 ( From Switch & Starter to Motor) pump installed in the bore.

Supply & errection of floor power shunt capacitor conforming to BIS 2834-1986 latest with upto date ammendments of GEC/Siemen/ Havells L&T make to raise the prevailing power factor at site to 0.95 for direct connection to induction motor individually of requirement KVAR according to BHP of motor offered including cable Siemens/Gloster/ ICC make from busbar chamber to capacitor & also including Standard/ L&T/Kilburn/Indo asian make ICTP switches conforming to BIS 4064- 4064-1978 or latest with HRC fuses.

Supply of standarad make 100 mm dia circular/square dial pressure gauge of suitable range Fiebeg/Bourden/ Precision make with all accessories such as stop cock, copper tubing etc. conforming to BIS 3624-1987 latest with up to date ammendments.

P/Laying Column assembly of G.I./MSERW pipe considering site requirements and having appropriate size in accordance with the delivery size of pumping set . The pipe shall conform to relevant BIS codes & capable of with standing the feild test pressure equal to 1.5 times the operating pressure including all type of fittings such as bends, tapers/ reducers, flanges, rubber gaskets 3mmthick, nuts & bolts and any other fitting required at site and work shall be to the entire satisfaction of Engineer-in-Charge. Column assembly = 80mm dia G.I.flanged pipe (medium grade) NOTE:- Actual laying to be done as per final drawings to be approved by the Engineer in charge

Errection of all equipments including the cost of tees, bends tapers & any other fittings required as per site conditions & as per directions of Engineer-in-Charge.

Ist. Stage Supply/errection and Commisning of horizontal spindle,horizontal/radial split casing and suction (backpull out arrangement) single/ double / multistage centrifugal pumps or combination of pumps in series /parallel of KSB / Mather & Platt/ Jyoti /Kirloskar /BE /Maxflow/ Beaconweir Sabar make conforming to BIS: 1520-1980 (latestwith upto date ammendments) read with BIS: 9137-1978 (latest edition) suitable for lifting clear water of under mentioned charactristics with impellers of bronze/suitable alloy, priming funnels,casing ring & shaft sleeves of bronze/ suitable alloy, shaft of sutable steel grade with cast iron casing coupled directly through a flexible coupling on a common C.I. / Cast steel base plate (base plate to be from the principle manufacturer of pumping set) to slippering/squirrel cage screen protected drip proof electric induction motor of Kirlokar/ NGEF/ Crompton /Siemen/Jyoti/BHEL/GEC/ABB conforming to BIS: 325-1978 read read with BIS: 900-1968 (latest with upto date ammendments) It should include the cost of bearings, nuts & bolts,painting etc. and shall be suitable for operation as per data given below. (i) Total Head 415.32 Metre (ii) Discharge required from each pump. 14.84 LPS (iii) No. of pump required 2.00 Nos pumping Set (iv) Location of the site of installation of machinery The site is located at a distance of 10 Kmts from Dehra (v) The altitude of installation. The altitude of place is 500.00 mtrs above MSL (Iv) Type of current. AC three phase supply with freqduency of 50 cycle per second. (V) Rate Voltage 415V + 10% (Vi) Type of water and its source Clear Cold Water Shaft level 495.45 Metre Level of discharge point 810.95 Metre Static Head 315.50 Metre (vii) Charactristics of water. - (a)Ambient Temperature dig.c - (b)Turbidity NTU - (c)Hardness260Mg/Ltrs(as CaCO3) - (d) PH 7.5 - (e)total solid Mg /Ltrs - (f)Other - Depth of well assembly - (xvi) No. of working hours per day 8 Hours. (xvii) Length of Rising main 10250 Metre (xviii) Dia of Rising main 150 mm dia GI/MSERW pipe (xix) Limit of pump operation. In the completem Range of (-)75% . (xx) R.P.M. of pumping set. 2900 RPM (or to be specified by the tenderer). (xxi) Test run. 16 Hours contineously for 7 days.

Supply, Installation, Testing and Commissioning of star delta starter panel for centrifugal pump made out of 16 Gauge sheet, powder coated dust and vermin proof wall/base mounted and front opening door type with copper insulated wiring suitable to operate 2 Nos. pump(1 working and i standby) of the reating 20.00 HP through Star Delta Starter Mechanism starter should be capable enough to handle the following faults like short circuit, over current , under current, over voltage, under voltage, dry run protection and phase loss with LED ON/OFF & TRIP indicator make Aarmation Electric Private Limited/MAS/ELLES/Adlec/L&T indicators 28.1 Star, Delta and Main Power Contactors of required ratings as per type-2 co-ordination for starter = 2 Set 28.2 Voltage protection device to protect panel from over voltage and under voltage = 2 Number 28.3 Single phasing and phase reversal protection device to safeguard system from single phasing and phase reversal of the supply voltage = 2 Number 28.4 Multi function meter indicating different parameters like current, voltage, KWH, PF, THD, etc. with Rs. 485 communication make Aarmaation/ L&T /Schneider/Siemens = 1 Number 28.5 Main incomer MCCB/MCB of suitble capacity of L&T/ Schneider/ABB make on the feeder for pumping set confirming to BIS2516-1985 (Letest edition) = 1 Number 28.6 Individual starter ncomer MCCB/MCB of suitble capacity of L&T/ Schneider/ABB make on the feeder of pumping set confirming to BIS2516-1985 (Letest edition) = 2 Set 28.7 Three phase indicating lamps complete with logged switches for individual motors conforming to BIS 3452 (Part I & II) latest with up to date amendments = 1 Set 28.8 LED On/Off & trip indicator and push buttons, Control and power wiring, Power capacitor, Cooling fan 230 VAC , Control terminal Bus Bar, i.e. Bolt, insulator etc. = 2 Number 28.9 Surge suppressor divice with isolating MCCB to eliminate the power surges due to lightening and system surges = 1 Number 28.10 Control Transformer to provide a stable control voltage to safeguarg the control circuit of all the components from the voltage surges and spikes = 1 Number

Supply of Kirloskar/Kilburn/IVC/Fouress/Gled/BHEL/Leader make Cast steel double flanged sluice valve of class ASA-300 confirming to BIS-1414(API-600) (to be provided on delivery side) of equal size to one dia more than the dia of delivery of pump and capable of with standing nominal seat test pressure of 52 kg/cm². NOTE :- The cast iron Sluice valve shall conform to BIS-780-1984 for 50 mm to 300 mm dia and BIS:2906-1984 for 350 mm to 1200 mm dia (latest eddition). However if seat pressure exceeds the limits prescribed in above mentioned BIS then it shall be of cast steel conforming to class ASA-150 for seat pressure up to 21 Kg./Cm2 & of class ASA-300 for seat pressure 52 Kg./Cm2 as per BS-1414 (API-600).

Supply of Kirloskar/Kilburn/IVC/Fouress/Gled/BHEL/Leader make Cast steel double flanged swing check type reflux valve having bypass arrangement of class ASA-300 confirming to BS 1868(API-600) (latest edition)to be provided on delivery side) of size one step higher than the delivery size of pump and shall be suitable for withstanding nominal seat pressure of 52 kg/cm².

Supply of Kirloskar/Kilburn/IVC/Fouress/Gled/BHEL/Leader make Cast iron double flanged swing check type reflux valve having bypass arrangement of class ASA-300 confirming to BS 1868(API-600) (latest edition)to be provided on Rising main) and shall be suitable for withstanding nominal seat pressure of 52 kg/cm². NOTE :- The reflux valve shall conform to BIS-5312-1984 (part-I) latest with upt date ammendments. However if seat pressure exceeds the limits prescribed in BIS 5312 then the reflux valves shall be of cast steel conformingt to class ASA-150 for seat pressure up to 21 Kg./Cm2 & of class ASA-300 for seat pressure 52 Kg./Cm2 as per BS-1414 (API-600).

Supply of Kirloskar/Kilburn/IVC/Fouress /Gled/BHEL/Leader make cast iron double flanged sluice valve class PN-I confirming to BIS 780-1984 (latest addition) to be provided on Suction side of size one dia higher then the suctrion size of pump capable of withstanding nominal seat pressure of 10.20 kg/cm².

Providing & laying PVC insulated jointless, flat water proof copper cable of Siemens/Finolex/Grandlay/Gloster make conforming to BIS:1554 (Part I) -1988 or latest with up to date ammendments of suitable size for the pump sets offered (one cable carrying all three phases) including all other electrical equipment /accessories such as thimbles,flexible pipe, solder, nuts & bolts cable glands etc. laid in pipes or trenches under floor. The type,size & make will be subject to approval of HPSEB authorities.In case of non acceptance by HPSEB authorities it shall have to be replaced by the tenderer free of cost. On supply side of 3½ core coper cable mm^2 (From HPSEB Meter to Switch & Starter)(Size to be specified by the tenderer)

On motor side 3 core flat joint less copper cable of size __ mm^2 ( From Switch & Starter to Motor) pump installed in the bore. (Size to be specified by the tenderer)

Supply & errection of floor/wall mounted power shunt capacitor conforming to BIS 2834-1986 latest with upto date ammendments of GEC/Siemen/Havells L&T make to raise the prevailing power factor at site to 0.95 for direct connection to induction motor individually of requirement KVAR according to BHP of motor offered including cable Siemens/Gloster/ ICC make from busbar chamber to capacitor & also including Standard/ L&T/Kilburn/Indo asian make ICTP switches conforming to BIS 4064- 4064-1978 or latest with HRC fuses. (range to be specified by the tenderer.)

Supply of standarad make 80mm dia circular/square dial pressure gauge of suitable range Fiebeg/ Bourden/ Precision make with all accessories such as stop cock,copper tubing etc. conforming to BIS 3624-1987 latest with up to date ammendments.

P/L GI/MSERW pipe considering site requirements and having appropriate size in accordance with the delivery size of pumping set . The pipe shall conform to relevant BIS codes & capable of with standing the feild test pressure equal to 1.5 times the operating pressure including all type of fittings such as bends, tapers/reducers, flanges, rubber gaskets 3mm thick, nuts & bolts and any other fitting required at site and work shall be to the entire satisfaction of Engineer-in-Charge. The pipe material shall conform to relevant BIS Code and capable of with standing FTP equal to 1.5 times the operating pressure the complete arrangement shall compromise of Suction Pipe = to be specified by the Tenderer

Delivery pipe = to be specified by the Tenderer

Common header = to be specified by the Tenderer NOTE:- Actual laying to be done as per final drawings to be approved by the Engineer in charge.

Providing and lying double loop earthing with coper plate 600x600 x3 thick electrode and copper strip of 25x3 complete including providing of material such as charcoal, common salt, GI pipes, thimbles, nuts & bolts, digging of pits, Copper /GI wire/ Strips of required capacity conforming to BIS 8034-1978 latest with upto date ammendments for above motor & other electriacl equipments including all civil works. (for both machineries). Note. The strip size shall be 20x3 upto 18.5 KW . 25x3 for 18.5 to 37 KW to 55 KW and 32x5 beyond 55 KW.

Errection of all equipments i/c cost of tees,bends tapers & any other fittings required as per site conditions & as per directions of Engineer-in-Charge.

sanjeev kumar

Ashwani Kumar Govt Contractor

Vijay kumar kushwaha

Shadil Thakur

sadeep kumar

SANGRAM NAIK