Construction of Lawyer's Hall Building at Sub-Divisional Court Manihari, Distt. Katihar.

BILL OF QUANTITY

Name of work :- Construction of Lawyer's Hall Building at Sub-Divisional Court Manihari, Distt. Katihar.

Estimated Cost : Rs Issued to Mr/Mrs/Smt:

Earnest Money: Rs Address:

Cost of B.O.Q Rs Reg. No.:

Date of Tender: M.R. No.& Date:

Time of Completion: Signature of Issuing officer:

S.No. SOR Discription Main Building Septik Tank Boring Sanitary Installation RWH Qty Unit Rate Amount

1 2.29.1 Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 mAll kinds of soil. 1088.858 - - - - 1088.858 100sqm ₹ 1,355.40 ₹ 14,758.00

2 2.8.1 Earth work in excavation in foundation trenches or drains(not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m . including getting out the excavated soil and disposal of surplusx cavated soil as directed, within a lead of 50 m. All Kinds of soil 339.269 23.38 9.375 - 2.458 374.482 CUM ₹ 360.70 ₹ 135,076.00

3 2.26 Filling available excavated earth(excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm indepth: consolidating each deposited layer by ramming and watering lead 60% of Total Earthwork 203.561 23.38 - - - 226.941 CUM ₹ 123.90 ₹ 28,118.00

4 2.27.1 Extra for every additional lift of 1.5 m or part thereof in: All Kinds of soil 95.579 9.007 - - - 104.586 CUM ₹ 49.40 ₹ 5,167.00

5 2.28 Supplying and Filling in plinth with local sand and under floors including, watering, ramming consolidating and dressing complete. 139.347 1.437 - - 0.113 140.897 CUM ₹ 287.30 ₹ 40,480.00

6 11.72 Providing designation 100 A one brick flat soling joints filled with local sand including cost of atering, taxes, royalty all complete as per building pecification and direction of E/l, 368.806 9.582 - - 1.487 379.875 SQM ₹ 283.30 ₹ 107,619.00

7 4.1.3 Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level.cum 1Cement: 2 coarse sand:4 graded stone aggregate 20 mm nominal size) 26.258 0.958 - - 0.113 27.329 CUM ₹ 3,998.10 ₹ 109,264.00

8 5.1.2 Providing and laying in position specified grade of reinforced cement concrete excluding the cost of entring,shuttering,finishing and reinforcement-All work puto plinth level 1:1:5:3 - - - - 0.267 0.267 CUM ₹ 4,688.30 ₹ 1,252.00

9 5.33.1.1 Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana /Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.. 90.676 1.265 - - 91.941 CUM ₹ 5,063.40 ₹ 465,534.00

10 6.1.14C Brick work with bricks of class designation FLYASH in foundations and plinth in : Cement mortar 1:6 (1 cement: 6 coarse sand ). 10.882 - - - 2.297 13.179 CUM ₹ 4,923.00 ₹ 64,880.00

11 6.1.12C Brick work with Fly ash bricks as per IS 12894 (2002) & 3495 in foundations and plinth in :Cement mortar 1:4(1 cement: 4 coarse sand ). - 7.221 - - - 7.221 CUM ₹ 5,116.30 ₹ 36,945.00

12 5.33.2.1 Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering finishing and reinforcement, M-20 grde reinforcd cement concrete Walls columns, pillars, posts cind struts 57.47625 - - - 57.476 CUM ₹ 5,863.20 ₹ 336,995.00

13 5.9 Centring and shuttering including strutting, propping etc. and removal of form for - -

a 5.9.1 .Foundations, footings, bases of columns etc. for mass concrete. 78.281 9.522 - - 87.803 SQM ₹ 211.60 ₹ 18,579.00

b 5.9.6 Columns,Pillars, Piers, butmentsPosts and Struts 210.52 - - - 210.520 SQM ₹ 494.40 ₹ 104,081.00

c 5.9.5 Lintels, beams, plinth bams, griders, bressumers and contilevers. 236.2 - - - 236.200 SQM ₹ 404.70 ₹ 95,590.00

d 5.9.3 Centring and shuttering including strutting,propping etc. and removal of form for. Suspended floors, roots, landings, balcnies and access platform. 126.808 - - - 126.808 SQM ₹ 437.50 ₹ 55,479.00

e 5.9.7 Centering and shuttering in Stair waist slab 18.308 - - - 18.308 SQM ₹ 439.90 ₹ 8,054.00

f 5.9.19 Centering and shuttering in Chajja , Rack 9.99 - - - 9.990 SQM ₹ 550.90 ₹ 5,503.00

g 5.9.16.1 Centering & shuttering in Edges of slab 56.162 - - - 56.162 SQM ₹ 130.20 ₹ 7,312.00

14 6.1.14C+6.3C Brick work with fly ash bricks as per IS 12894(2002) & IS 3495 in foundations and plinth in : Cement mortar 1:6 (1 cement: 6 coarse sand ) Extra tor Brick work in superstructure above plinth level upto floor V cum 45.39 - - - 45.390 CUM ₹ 5,765.20 ₹ 261,682.00

15 6.1.12C+ 6.3C Half brick masonry with bricks of class designation100A in foundations and plinth in : Cement mortar 1:4 (1 cement: 4 coarse send) Extra for half Brick masonry in superstructure above pinth level upto floor V level. 4.652 - - - 4.652 CUM ₹ 5,958.50 ₹ 27,719.00

16 13.11.4 12 mmCement plaster in course sand 1:6(1 cement: 6 coarse sand) 356.05 - - - 356.050 SQM ₹ 141.50 ₹ 50,381.00

17 13.17.1 12 mm cement plaster 1:3( 1 cement: 3 coarse sand) finished with a floating coat of near cement - - - 5.33 5.330 SQM ₹ 203.60 ₹ 1,085.00

18 13.12.4 15 mm cement plaster 1:6 (inside surface) 319.343 - - 319.343 SQM ₹ 162.80 ₹ 51,989.00

19 13.24.2 6 mm cement plaster to ceiling of mix : 1:4(1 cement: 4 coarse sand) 150.981 - - 150.981 SQM ₹ 125.60 ₹ 18,963.00

20 13.18 + 13.36.3 15 mm cement plaster of mix 1:3(1 cement: 3 sand) Extra for providing and mixing water proofing material in proportion recommended by the manufacturers: - 43.515 - - 43.515 SQM ₹ 239.60 ₹ 10,426.00

21 13.18 15 mm plaster 1:3 with cement punning 77.966 - - - 77.966 SQM ₹ 229.30 ₹ 17,878.00

23 0L01 Labour required for Brick bats - 2 - - 2.000 no ₹ 355.42 ₹ 711.00

24 11.37 Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of ist quality conforming to IS : 15622 of approved make in colours such as white , Ivory , Grey , Fume Red , Brown , laid on 20 mm thick Cement motar 1:4 (1 cement: 4 coarse sand ) including pointing the joints with white cement and matching pigment etc., complete. 16.895 - - - 16.895 SQM ₹ 686.80 ₹ 11,603.00

26 11.36 Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (Thickness to be specified by the manufacture) of approved make in all colours, shades except burgundy , bottle green , black of any size as approved by Engineer-in-charge in skirting , risers of steps and dados over 12 mm thick bed of cement Motar 1:3(1 cement: 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete. 70.581 - - - 70.581 SQM ₹ 795.00 ₹ 56,112.00

27 11.26.1 Kota stone slab flooring over 20 mm (average ) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete . Base with 1:1:1 (1 lime : 1 surkhi: 1 coarse sand ) / 1:4 (1 cement: 4 coarse sand ) 20 to 25 mm thick - 140.57 - - - 140.570 SQM ₹ 1,252.70 ₹ 176,092.00

28 11.27 Kota stone slabs 20 mm thick in risers of steps skirting. Dado & pillars laid on 12 mm (average (thick cement mortar 1:3 (1 cement: 3 coarse sand ) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete. Details of cost for 10 sqm 17.559 - - - 17.559 SQM ₹ 1,334.90 ₹ 23,440.00

29 10.18 Providing and fixing M.S.fan clamp type I or II of 16 mm dia.M.S. bar bent to shape with hooked ends in R.C.C slabs during laying including painting the exposed portion of loop,all as per standard design complete. 20.00 - - - 20.000 Each ₹ 165.40 ₹ 3,308.00

30 5.22 Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. - - -

5.22.7A Thermo-Mechanically Treated bars TMTC-500-8mm dia. 5760 - - - 21.36 5781.360 KG ₹ 94.50 ₹ 546,339.00

5.22.7B Thermo-Mechanically Treated bars TMTC-500-10mm dia. 1894.5515 94 - - 1988.552 KG ₹ 92.60 ₹ 184,140.00

5.22.7C Thermo-Mechanically Treated bars TMTC-500-12mm dia. 3840 - - - 3840.000 KG ₹ 90.80 ₹ 348,672.00

5.22.7D Thermo-Mechanically Treated bars TMTC-500-16mm dia. 5760 - - - 5760.000 KG ₹ 91.70 ₹ 528,192.00

5.22.7E Thermo-Mechanically Treated bars TMTC-500-20mm dia. 1920 - - - 1920.000 KG ₹ 91.70 ₹ 176,064.00

31 10.15.1.1 Providing and fixing pressed steel door confirming IS code 4351 manufactured from commerical mild steel sheet of 1.25 mm thickness including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50 x 25 mm or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by . mechnical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-incharge Pressed Steel Door Frame Profile B 32.7 - - - 32.700 mtr ₹ 405.80 ₹ 13,270.00

32 9.20.1 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type,core of block board construction with frame of 1 st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butthinges with necessary screws. 13.23 - - - 13.230 SQM ₹ 2,845.60 ₹ 37,647.00

33 9.147F.1 roviding and fixing factory made uPVC white colour sliding glazed door comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension uPVC extruded glazing beads, uPVC extruded interlock and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) cresent lock (if required), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, al complete as per approved drawing & direction of Engineer-inCharge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable 5.355 - - - 5.355 SQM ₹ 6,404.80 ₹ 34,298.00

34 9.48.2 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings/ wooden frames with rawl plugs screws etc 697.125 - - - 697.125 KG ₹ 161.10 ₹ 112,307.00

35 10.36 Providing and fixing stainless steel (Grade 304) rail ing by welding etc complete as per manufacturer’s specification and direction of Engineer-in-charge.. 12.9 - - - 12.900 Kg ₹ 546.80 ₹ 7,054.00

36 9.66.2 Providing and fixing ISI marked oxidised M.S. handles conforming to IS :4992 with necessary screws etc. complete: 100 mm 16 - - - 16.000 Each ₹ 25.50 ₹ 408.00

38 9.63.2 Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete: 8 - - - 8.000 Each ₹ 56.40 ₹ 451.00

40 10.12.1 Providing and fixing steel glazed doors, windows and ventilatrs of standard rolled steel sections, joints mitered and welded with 15x3 mm lugs 10 cm long with steel lugs embedded in cement concrete blocks 15x10x10 cm of 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with woodenplugs and screws or raw) plugs and screws or with fixing dips or with bolts and nuts as required, including providing and fixing of glass panes with glazing dips and special metal-sash putty pf approved make complete including applying a priming coat of approved steel primer; excluding the cost of metal beading and other fitting except necessary hinges or pivots as required. 34.721 - - - 34.721 SQM ₹ 3,038.90 ₹ 105,514.00

41 (i) 10.13B Extra for providing and fixing steel beading of approved shape and section with screws instread of glaxing clips and met. Sash putty in steel doors, windows, Ventilators and comosite units. Steel windows 32.291 - - - 32.291 SQM ₹ 396.70 ₹ 12,810.00

(ii) 10.13C Steel ventilators 2.43 - - - 2.430 SQM ₹ 405.30 ₹ 985.00

42 13.79.1+ 13.78.1 Finishing walls with water proofing cement paint of approved brand and manufacture and of required shade to give an even shade Applying one coat of cement primer of approved brand and manufacture on wall surface: 366.04 - - - 366.040 SQM ₹ 119.80 ₹ 43,852.00

43 13.80A.2 Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete 470.324 - - - 470.324 SQM ₹ 105.40 ₹ 49,572.00

44 13.77.2 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade .New work (two or more coats ) over and including priming coat with cement primer 460.334 - - - 460.334 SQM ₹ 102.30 ₹ 47,092.00

45 13.81.3 + 13.82.1 Painting with ready mixed paint of approved brand and manufacture in all shades to give an even shade: New steel work (two or more coats) With ready mixed zinc chromate yellow primer of approvedbrand and manufacture on steel alvanized iron/steelworks 46.475 - - - 46.475 SQM ₹ 118.10 ₹ 5,489.00

46 Carriage of Material- - - -

47 Extra Cost of Material - - -

48 12.78 Providing and fixing on wall face unplastidsed- PVC(working pressure 4 kgf per sqm) rain water pipes conforming to IS :4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

49 12.79 Providing and fixing on wall face unplasticised -PVC molded fittings /accessories for unplasticised-PVC rain water pipes conforming to (S:4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion. - - -

D 12.79.4.1 75 mm Single tee without door - - - 3 - 3 No ₹ 124.20 ₹ 373.00

E 12.79.4.2 110mm Single tee without doorShoe 16 - - 3 - 19 No ₹ 190.70 ₹ 3,623.00

50 12.80 Providing and fixing unplasticised -PVC pipe clip of approved design to unplasticised PVC rain water pipe by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing on cement mortar(1:4) 1 cement: 4corsa sand and making good the wall etc complete - - -

51 12.81 Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. 10 - - - - 10 Each ₹ 47.90 ₹ 479.00

52 17.1.1 Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mm sand cast Iron P or S trap, 10 litre low fixtures complete, including cutting and making good the walls andlevel white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and floors wherever required : White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests - - - 2 - 2 EACH ₹ 4,470.90 ₹ 8,942.00

53 17.3.1 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : - - - 1 - 1 EACH ₹ 5,504.30 ₹ 5,504.00

54 17.4.1 Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : One urinal basin with 5 litre white P.V.C. automatic flushing cistern - - - 1 - 1 EACH ₹ 3,723.20 ₹ 3,723.00

55 17.7.1 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps - - - 3 - 3 EACH ₹ 2,764.40 ₹ 8,293.00

56 17.28.1.1 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Semi rigid pipe 32 mm dia - - - 3 - 3 No ₹ 91.00 ₹ 273.00

57 17.34.1 Providing and fixing toilet paper holder :C.P. brass - - - 3 - 3 No ₹ 550.70 ₹ 1,652.00

58 17.71 Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. - - - 3 - 3 No ₹ 146.30 ₹ 439.00

59 17.72 Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour,weighing not less than 88 gms. - - - 3 - 3 No ₹ 204.70 ₹ 614.00

60 17.16A Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. - - - 1 - 1 No ₹ 299.40 ₹ 299.00

61 17.31 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. - - - 3 - 3 Each ₹ 1,068.50 ₹ 3,206.00

62 8.2.2.2 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups,including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. - - - 0.9 - 0.9 sqm ₹ 4,401.20 ₹ 3,961.00

63 18.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. -

A 18.8.1 15 mm nominal outer dia Pipes - - - 15 - 15 M ₹ 278.20 ₹ 4,173.00

B 18.8.2 20 mm nominal outer dia Pipes - - - 21 - 21 m ₹ 350.80 ₹ 7,367.00

64 18.9 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge - - - -

A 18.9.3 25 mm nominal outer dia Pipes - - - 20 - 20 m ₹ 294.70 ₹ 5,894.00

B 18.9.5 40 mm nominal outer dia Pipes - - 15 - 15 m ₹ 477.60 ₹ 7,164.00

65 18.19 Providing and fixing gun metal non- return valve of approved quality (screwed end) : - -

66 18.18.3 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 25 mm nominal bore - - - 1 - 1 no 399.20 ₹ 399.00

67 18.17 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : - - -

68 18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. - - - 1000 - 1000 ltr 9.70 ₹ 9,700.00

69 18.49 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : - - - 3 - 3 No ₹ 434.20 ₹ 1,303.00

70 18.52.1 Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.15 mm nominal bore - - - 4 - 2 No ₹ 594.80 ₹ 1,190.00

71 18.53.1 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore 15 mm nominal bore - - - 4 - 4 No ₹ 500.40 ₹ 2,002.00

72 18.74.2 Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 15 mm nominal bore with 45 cm length - - - 3 - 3 No ₹ 108.00 ₹ 324.00

73 18.75.3 Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour. 25mm nominal bore, weighing not less than 62 gms - - - 1 - 1 No ₹ 100.60 ₹ 101.00

74 18.9.5 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. 32mm - - 27 - - 27 M ₹ 477.60 ₹ 12,895.00

75 19.6.2 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe - - - 9 - 9 m ₹ 410.70 ₹ 3,696.00

76 19.7.1.1 Constructing brick masonry manhole in cement mortar 1:4 ( 1cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : - - - 2 - 2 Each ₹ 7,914.70 ₹ 15,829.00

77 24.1.1.1 Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre depth below ground level. All types of soil 300 mm dia - - 60 - 15 75.00 metre ₹ 486.80 ₹ 36,510.00

78 24.3.2 Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths,as per direction of Engineer -in-charge.150 mm nominal size dia - - 54 - - 54 metre ₹ 660.10 ₹ 35,645.00

79 24.4.2 Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.150 mm nominal size dia - - 6 - 15 21.00 metre ₹ 673.50 ₹ 14,144.00

80 24.5 Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. - - - - 0.31 0.31 CUM ₹ 1,188.90 ₹ 369.00

81 24.6 Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. ) - - - - 0.88 0.88 CUM ₹ 1,195.60 ₹ 1,052.00

82 24.7 Supplying, filling, spreading & leveling gravels of size range 1.5 mm to 2 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. ) - - - - 0.19 0.19 CUM ₹ 1,195.60 ₹ 227.00

83 24.8 Gravel packing in tubewell construction in accordance with IS: 4097,including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge. - - 3.182 - - 3.182 metre ₹ 1,343.20 ₹ 4,274.00

84 24.10.2 Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 mild steel screwed and socketed/ plain ended casing pipes of required dia,conforming to IS: 4270, of reputed & approved make, including painted with outside surface with two coats of anticorrosive paint of approved brand and manufacture, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer-incharge. - - 1 - - 1 M ₹ 1,408.10 ₹ 1,408.00

85 24.12 Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully develo ped, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge. - - 8 - - 8 hour ₹ 916.80 ₹ 7,334.00

86 24.13.2 Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of:150 mm dia - - 1 - - 1.00 each ₹ 210.70 ₹ 211.00

87 24.14.2 Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.150 mm clamp - - 1 - - 1.00 each ₹ 1,531.40 ₹ 1,531.00

88 24.15.2 Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I).150 mm dia - - 1 - - 1.00 each ₹ 281.80 ₹ 282.00

Correction factor @ 0.982 on all SOR Item A ₹ 5,688,190.81

Total Amount (A+B) ₹ 5,993,077.84

89 Approved by S.E S/F/F 2 H.P Crompton Submersible Pump of ISI marka electric wire switch, starter etc. 1.00 each ₹ 23,659.00 ₹ 23,659.00

90 Approved by S.E Supplying, Fitting and Fixing Fire CO2 type Fire Extinguisher Capacity of 4.50 Kg of approved brand and manufactures including all cost of Labour, materials, and taxes all complete job. 7.000 Nos ₹ 12,489.12 ₹ 87,424.00

Total Amount 6104160.84

Say, Total ₹6,104,161

Executive Engineer

Building Division

BILL OF QUANTITY

Name of work :- Construction of Lawyer's Hall Building at Sub-Divisional Court Manihari, Distt. Katihar.

Estimated Cost : Rs Issued to Mr/Mrs/Smt:

Earnest Money: Rs Address:

Cost of B.O.Q Rs Reg. No.:

Date of Tender: M.R. No.& Date:

Time of Completion: Signature of Issuing officer:

S.No. SOR Discription Main Building Septik Tank Boring Sanitary Installation RWH Qty Unit Rate Amount

1 2.29.1 Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 mAll kinds of soil. 1088.858 - - - - 1088.858 100sqm ₹ 1,355.40 ₹ 14,758.00

2 2.8.1 Earth work in excavation in foundation trenches or drains(not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m . including getting out the excavated soil and disposal of surplusx cavated soil as directed, within a lead of 50 m. All Kinds of soil 339.269 23.38 9.375 - 2.458 374.482 CUM ₹ 360.70 ₹ 135,076.00

3 2.26 Filling available excavated earth(excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm indepth: consolidating each deposited layer by ramming and watering lead 60% of Total Earthwork 203.561 23.38 - - - 226.941 CUM ₹ 123.90 ₹ 28,118.00

4 2.27.1 Extra for every additional lift of 1.5 m or part thereof in: All Kinds of soil 95.579 9.007 - - - 104.586 CUM ₹ 49.40 ₹ 5,167.00

5 2.28 Supplying and Filling in plinth with local sand and under floors including, watering, ramming consolidating and dressing complete. 139.347 1.437 - - 0.113 140.897 CUM ₹ 287.30 ₹ 40,480.00

6 11.72 Providing designation 100 A one brick flat soling joints filled with local sand including cost of atering, taxes, royalty all complete as per building pecification and direction of E/l, 368.806 9.582 - - 1.487 379.875 SQM ₹ 283.30 ₹ 107,619.00

7 4.1.3 Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level.cum 1Cement: 2 coarse sand:4 graded stone aggregate 20 mm nominal size) 26.258 0.958 - - 0.113 27.329 CUM ₹ 3,998.10 ₹ 109,264.00

8 5.1.2 Providing and laying in position specified grade of reinforced cement concrete excluding the cost of entring,shuttering,finishing and reinforcement-All work puto plinth level 1:1:5:3 - - - - 0.267 0.267 CUM ₹ 4,688.30 ₹ 1,252.00

9 5.33.1.1 Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana /Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.. 90.676 1.265 - - 91.941 CUM ₹ 5,063.40 ₹ 465,534.00

10 6.1.14C Brick work with bricks of class designation FLYASH in foundations and plinth in : Cement mortar 1:6 (1 cement: 6 coarse sand ). 10.882 - - - 2.297 13.179 CUM ₹ 4,923.00 ₹ 64,880.00

11 6.1.12C Brick work with Fly ash bricks as per IS 12894 (2002) & 3495 in foundations and plinth in :Cement mortar 1:4(1 cement: 4 coarse sand ). - 7.221 - - - 7.221 CUM ₹ 5,116.30 ₹ 36,945.00

12 5.33.2.1 Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering finishing and reinforcement, M-20 grde reinforcd cement concrete Walls columns, pillars, posts cind struts 57.47625 - - - 57.476 CUM ₹ 5,863.20 ₹ 336,995.00

13 5.9 Centring and shuttering including strutting, propping etc. and removal of form for - -

a 5.9.1 .Foundations, footings, bases of columns etc. for mass concrete. 78.281 9.522 - - 87.803 SQM ₹ 211.60 ₹ 18,579.00

b 5.9.6 Columns,Pillars, Piers, butmentsPosts and Struts 210.52 - - - 210.520 SQM ₹ 494.40 ₹ 104,081.00

c 5.9.5 Lintels, beams, plinth bams, griders, bressumers and contilevers. 236.2 - - - 236.200 SQM ₹ 404.70 ₹ 95,590.00

d 5.9.3 Centring and shuttering including strutting,propping etc. and removal of form for. Suspended floors, roots, landings, balcnies and access platform. 126.808 - - - 126.808 SQM ₹ 437.50 ₹ 55,479.00

e 5.9.7 Centering and shuttering in Stair waist slab 18.308 - - - 18.308 SQM ₹ 439.90 ₹ 8,054.00

f 5.9.19 Centering and shuttering in Chajja , Rack 9.99 - - - 9.990 SQM ₹ 550.90 ₹ 5,503.00

g 5.9.16.1 Centering & shuttering in Edges of slab 56.162 - - - 56.162 SQM ₹ 130.20 ₹ 7,312.00

14 6.1.14C+6.3C Brick work with fly ash bricks as per IS 12894(2002) & IS 3495 in foundations and plinth in : Cement mortar 1:6 (1 cement: 6 coarse sand ) Extra tor Brick work in superstructure above plinth level upto floor V cum 45.39 - - - 45.390 CUM ₹ 5,765.20 ₹ 261,682.00

15 6.1.12C+ 6.3C Half brick masonry with bricks of class designation100A in foundations and plinth in : Cement mortar 1:4 (1 cement: 4 coarse send) Extra for half Brick masonry in superstructure above pinth level upto floor V level. 4.652 - - - 4.652 CUM ₹ 5,958.50 ₹ 27,719.00

16 13.11.4 12 mmCement plaster in course sand 1:6(1 cement: 6 coarse sand) 356.05 - - - 356.050 SQM ₹ 141.50 ₹ 50,381.00

17 13.17.1 12 mm cement plaster 1:3( 1 cement: 3 coarse sand) finished with a floating coat of near cement - - - 5.33 5.330 SQM ₹ 203.60 ₹ 1,085.00

18 13.12.4 15 mm cement plaster 1:6 (inside surface) 319.343 - - 319.343 SQM ₹ 162.80 ₹ 51,989.00

19 13.24.2 6 mm cement plaster to ceiling of mix : 1:4(1 cement: 4 coarse sand) 150.981 - - 150.981 SQM ₹ 125.60 ₹ 18,963.00

20 13.18 + 13.36.3 15 mm cement plaster of mix 1:3(1 cement: 3 sand) Extra for providing and mixing water proofing material in proportion recommended by the manufacturers: - 43.515 - - 43.515 SQM ₹ 239.60 ₹ 10,426.00

21 13.18 15 mm plaster 1:3 with cement punning 77.966 - - - 77.966 SQM ₹ 229.30 ₹ 17,878.00

23 0L01 Labour required for Brick bats - 2 - - 2.000 no ₹ 355.42 ₹ 711.00

24 11.37 Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of ist quality conforming to IS : 15622 of approved make in colours such as white , Ivory , Grey , Fume Red , Brown , laid on 20 mm thick Cement motar 1:4 (1 cement: 4 coarse sand ) including pointing the joints with white cement and matching pigment etc., complete. 16.895 - - - 16.895 SQM ₹ 686.80 ₹ 11,603.00

26 11.36 Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (Thickness to be specified by the manufacture) of approved make in all colours, shades except burgundy , bottle green , black of any size as approved by Engineer-in-charge in skirting , risers of steps and dados over 12 mm thick bed of cement Motar 1:3(1 cement: 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete. 70.581 - - - 70.581 SQM ₹ 795.00 ₹ 56,112.00

27 11.26.1 Kota stone slab flooring over 20 mm (average ) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete . Base with 1:1:1 (1 lime : 1 surkhi: 1 coarse sand ) / 1:4 (1 cement: 4 coarse sand ) 20 to 25 mm thick - 140.57 - - - 140.570 SQM ₹ 1,252.70 ₹ 176,092.00

28 11.27 Kota stone slabs 20 mm thick in risers of steps skirting. Dado & pillars laid on 12 mm (average (thick cement mortar 1:3 (1 cement: 3 coarse sand ) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete. Details of cost for 10 sqm 17.559 - - - 17.559 SQM ₹ 1,334.90 ₹ 23,440.00

29 10.18 Providing and fixing M.S.fan clamp type I or II of 16 mm dia.M.S. bar bent to shape with hooked ends in R.C.C slabs during laying including painting the exposed portion of loop,all as per standard design complete. 20.00 - - - 20.000 Each ₹ 165.40 ₹ 3,308.00

30 5.22 Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. - - -

5.22.7A Thermo-Mechanically Treated bars TMTC-500-8mm dia. 5760 - - - 21.36 5781.360 KG ₹ 94.50 ₹ 546,339.00

5.22.7B Thermo-Mechanically Treated bars TMTC-500-10mm dia. 1894.5515 94 - - 1988.552 KG ₹ 92.60 ₹ 184,140.00

5.22.7C Thermo-Mechanically Treated bars TMTC-500-12mm dia. 3840 - - - 3840.000 KG ₹ 90.80 ₹ 348,672.00

5.22.7D Thermo-Mechanically Treated bars TMTC-500-16mm dia. 5760 - - - 5760.000 KG ₹ 91.70 ₹ 528,192.00

5.22.7E Thermo-Mechanically Treated bars TMTC-500-20mm dia. 1920 - - - 1920.000 KG ₹ 91.70 ₹ 176,064.00

31 10.15.1.1 Providing and fixing pressed steel door confirming IS code 4351 manufactured from commerical mild steel sheet of 1.25 mm thickness including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50 x 25 mm or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by . mechnical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-incharge Pressed Steel Door Frame Profile B 32.7 - - - 32.700 mtr ₹ 405.80 ₹ 13,270.00

32 9.20.1 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type,core of block board construction with frame of 1 st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butthinges with necessary screws. 13.23 - - - 13.230 SQM ₹ 2,845.60 ₹ 37,647.00

33 9.147F.1 roviding and fixing factory made uPVC white colour sliding glazed door comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension uPVC extruded glazing beads, uPVC extruded interlock and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) cresent lock (if required), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, al complete as per approved drawing & direction of Engineer-inCharge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable 5.355 - - - 5.355 SQM ₹ 6,404.80 ₹ 34,298.00

34 9.48.2 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings/ wooden frames with rawl plugs screws etc 697.125 - - - 697.125 KG ₹ 161.10 ₹ 112,307.00

35 10.36 Providing and fixing stainless steel (Grade 304) rail ing by welding etc complete as per manufacturer’s specification and direction of Engineer-in-charge.. 12.9 - - - 12.900 Kg ₹ 546.80 ₹ 7,054.00

36 9.66.2 Providing and fixing ISI marked oxidised M.S. handles conforming to IS :4992 with necessary screws etc. complete: 100 mm 16 - - - 16.000 Each ₹ 25.50 ₹ 408.00

38 9.63.2 Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete: 8 - - - 8.000 Each ₹ 56.40 ₹ 451.00

40 10.12.1 Providing and fixing steel glazed doors, windows and ventilatrs of standard rolled steel sections, joints mitered and welded with 15x3 mm lugs 10 cm long with steel lugs embedded in cement concrete blocks 15x10x10 cm of 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with woodenplugs and screws or raw) plugs and screws or with fixing dips or with bolts and nuts as required, including providing and fixing of glass panes with glazing dips and special metal-sash putty pf approved make complete including applying a priming coat of approved steel primer; excluding the cost of metal beading and other fitting except necessary hinges or pivots as required. 34.721 - - - 34.721 SQM ₹ 3,038.90 ₹ 105,514.00

41 (i) 10.13B Extra for providing and fixing steel beading of approved shape and section with screws instread of glaxing clips and met. Sash putty in steel doors, windows, Ventilators and comosite units. Steel windows 32.291 - - - 32.291 SQM ₹ 396.70 ₹ 12,810.00

(ii) 10.13C Steel ventilators 2.43 - - - 2.430 SQM ₹ 405.30 ₹ 985.00

42 13.79.1+ 13.78.1 Finishing walls with water proofing cement paint of approved brand and manufacture and of required shade to give an even shade Applying one coat of cement primer of approved brand and manufacture on wall surface: 366.04 - - - 366.040 SQM ₹ 119.80 ₹ 43,852.00

43 13.80A.2 Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete 470.324 - - - 470.324 SQM ₹ 105.40 ₹ 49,572.00

44 13.77.2 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade .New work (two or more coats ) over and including priming coat with cement primer 460.334 - - - 460.334 SQM ₹ 102.30 ₹ 47,092.00

45 13.81.3 + 13.82.1 Painting with ready mixed paint of approved brand and manufacture in all shades to give an even shade: New steel work (two or more coats) With ready mixed zinc chromate yellow primer of approvedbrand and manufacture on steel alvanized iron/steelworks 46.475 - - - 46.475 SQM ₹ 118.10 ₹ 5,489.00

46 Carriage of Material- - - -

47 Extra Cost of Material - - -

48 12.78 Providing and fixing on wall face unplastidsed- PVC(working pressure 4 kgf per sqm) rain water pipes conforming to IS :4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

49 12.79 Providing and fixing on wall face unplasticised -PVC molded fittings /accessories for unplasticised-PVC rain water pipes conforming to (S:4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion. - - -

D 12.79.4.1 75 mm Single tee without door - - - 3 - 3 No ₹ 124.20 ₹ 373.00

E 12.79.4.2 110mm Single tee without doorShoe 16 - - 3 - 19 No ₹ 190.70 ₹ 3,623.00

50 12.80 Providing and fixing unplasticised -PVC pipe clip of approved design to unplasticised PVC rain water pipe by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing on cement mortar(1:4) 1 cement: 4corsa sand and making good the wall etc complete - - -

51 12.81 Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. 10 - - - - 10 Each ₹ 47.90 ₹ 479.00

52 17.1.1 Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mm sand cast Iron P or S trap, 10 litre low fixtures complete, including cutting and making good the walls andlevel white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and floors wherever required : White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests - - - 2 - 2 EACH ₹ 4,470.90 ₹ 8,942.00

53 17.3.1 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : - - - 1 - 1 EACH ₹ 5,504.30 ₹ 5,504.00

54 17.4.1 Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : One urinal basin with 5 litre white P.V.C. automatic flushing cistern - - - 1 - 1 EACH ₹ 3,723.20 ₹ 3,723.00

55 17.7.1 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps - - - 3 - 3 EACH ₹ 2,764.40 ₹ 8,293.00

56 17.28.1.1 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Semi rigid pipe 32 mm dia - - - 3 - 3 No ₹ 91.00 ₹ 273.00

57 17.34.1 Providing and fixing toilet paper holder :C.P. brass - - - 3 - 3 No ₹ 550.70 ₹ 1,652.00

58 17.71 Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. - - - 3 - 3 No ₹ 146.30 ₹ 439.00

59 17.72 Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour,weighing not less than 88 gms. - - - 3 - 3 No ₹ 204.70 ₹ 614.00

60 17.16A Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. - - - 1 - 1 No ₹ 299.40 ₹ 299.00

61 17.31 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. - - - 3 - 3 Each ₹ 1,068.50 ₹ 3,206.00

62 8.2.2.2 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups,including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. - - - 0.9 - 0.9 sqm ₹ 4,401.20 ₹ 3,961.00

63 18.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. -

A 18.8.1 15 mm nominal outer dia Pipes - - - 15 - 15 M ₹ 278.20 ₹ 4,173.00

B 18.8.2 20 mm nominal outer dia Pipes - - - 21 - 21 m ₹ 350.80 ₹ 7,367.00

64 18.9 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge - - - -

A 18.9.3 25 mm nominal outer dia Pipes - - - 20 - 20 m ₹ 294.70 ₹ 5,894.00

B 18.9.5 40 mm nominal outer dia Pipes - - 15 - 15 m ₹ 477.60 ₹ 7,164.00

65 18.19 Providing and fixing gun metal non- return valve of approved quality (screwed end) : - -

66 18.18.3 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 25 mm nominal bore - - - 1 - 1 no 399.20 ₹ 399.00

67 18.17 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : - - -

68 18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. - - - 1000 - 1000 ltr 9.70 ₹ 9,700.00

69 18.49 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : - - - 3 - 3 No ₹ 434.20 ₹ 1,303.00

70 18.52.1 Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.15 mm nominal bore - - - 4 - 2 No ₹ 594.80 ₹ 1,190.00

71 18.53.1 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore 15 mm nominal bore - - - 4 - 4 No ₹ 500.40 ₹ 2,002.00

72 18.74.2 Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 15 mm nominal bore with 45 cm length - - - 3 - 3 No ₹ 108.00 ₹ 324.00

73 18.75.3 Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour. 25mm nominal bore, weighing not less than 62 gms - - - 1 - 1 No ₹ 100.60 ₹ 101.00

74 18.9.5 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. 32mm - - 27 - - 27 M ₹ 477.60 ₹ 12,895.00

75 19.6.2 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe - - - 9 - 9 m ₹ 410.70 ₹ 3,696.00

76 19.7.1.1 Constructing brick masonry manhole in cement mortar 1:4 ( 1cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : - - - 2 - 2 Each ₹ 7,914.70 ₹ 15,829.00

77 24.1.1.1 Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre depth below ground level. All types of soil 300 mm dia - - 60 - 15 75.00 metre ₹ 486.80 ₹ 36,510.00

78 24.3.2 Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths,as per direction of Engineer -in-charge.150 mm nominal size dia - - 54 - - 54 metre ₹ 660.10 ₹ 35,645.00

79 24.4.2 Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.150 mm nominal size dia - - 6 - 15 21.00 metre ₹ 673.50 ₹ 14,144.00

80 24.5 Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. - - - - 0.31 0.31 CUM ₹ 1,188.90 ₹ 369.00

81 24.6 Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. ) - - - - 0.88 0.88 CUM ₹ 1,195.60 ₹ 1,052.00

82 24.7 Supplying, filling, spreading & leveling gravels of size range 1.5 mm to 2 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. ) - - - - 0.19 0.19 CUM ₹ 1,195.60 ₹ 227.00

83 24.8 Gravel packing in tubewell construction in accordance with IS: 4097,including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge. - - 3.182 - - 3.182 metre ₹ 1,343.20 ₹ 4,274.00

84 24.10.2 Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 mild steel screwed and socketed/ plain ended casing pipes of required dia,conforming to IS: 4270, of reputed & approved make, including painted with outside surface with two coats of anticorrosive paint of approved brand and manufacture, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer-incharge. - - 1 - - 1 M ₹ 1,408.10 ₹ 1,408.00

85 24.12 Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully develo ped, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge. - - 8 - - 8 hour ₹ 916.80 ₹ 7,334.00

86 24.13.2 Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of:150 mm dia - - 1 - - 1.00 each ₹ 210.70 ₹ 211.00

87 24.14.2 Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.150 mm clamp - - 1 - - 1.00 each ₹ 1,531.40 ₹ 1,531.00

88 24.15.2 Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I).150 mm dia - - 1 - - 1.00 each ₹ 281.80 ₹ 282.00

Correction factor @ 0.982 on all SOR Item A ₹ 5,688,190.81

Total Amount (A+B) ₹ 5,993,077.84

89 Approved by S.E S/F/F 2 H.P Crompton Submersible Pump of ISI marka electric wire switch, starter etc. 1.00 each ₹ 23,659.00 ₹ 23,659.00

90 Approved by S.E Supplying, Fitting and Fixing Fire CO2 type Fire Extinguisher Capacity of 4.50 Kg of approved brand and manufactures including all cost of Labour, materials, and taxes all complete job. 7.000 Nos ₹ 12,489.12 ₹ 87,424.00

Total Amount 6104160.84

Say, Total ₹6,104,161

Executive Engineer

Building Division