Repir to 16 Mtr.Highmast Poles at Madhuben Dam,Dist. Valsad.

Name Of Repir to 16 Mtr.Highmast Poles at Madhuben Dam,Dist. Valsad.

Item SOR Rate with

Qty. Unit words Amount

No. Rate 1% L.S.

30 Mtr 1 Replacing old & u/s by Supplying and erecting 77.00 77.77 #NAME?

Flexible PVC insulated multi strand multi core

1.1 kv grade ISI marked copper wires of

following size to be erected as directed. (h)

Sq.mm 3 core round PVC sheathed

30 Nos 2 Replacing old & u/s by Supplying and erecting 10711.00 10818.11 #NAME?

LED street light / Flood light fittings with High

power White LEDs wattage of 3 Watt and above

assembled on single MCPCB, efficiency more than

130 lm/w and corrosion free High pressure die cast

aluminum housing with smooth finish powder

coated and heat sink extruded aluminium with

diffuser and Polycarbonate optics/ lenses, with

toughened glass with company mark/name

engraved or embossed 160 to 270 V,Power Factor

more than 0.95, THD < 10 %, CCT 3000 K to

5700K,Uniformity ratio >0.45, Luminaire

efficacy> 100 lumens/watt . LED driver efficiency

> 85 %.( fittings required LM-79 & LM-80

certificates)(NOTE: Below description have shown

ranges of Wattage capacity of LED fittings.The

Engineer incharge may select any wattage capacity

between the ranges shown.) (B) Flood Light (IP-

65), Surge protection -4KV integral and ,Light

must have 440VAC line supply with over-voltage

protection. (vii) 250 watts Cat-lll

1 Nos 3 providing and erecting Approved make Four pole 6112.00 6173.12 #NAME?

moulded case circuit breaker having breaking

capacity ICU of 25 KA. at 415 V,having normal

current rating up to 25 A to 100A. with Fixed

thermal & magnetic release suitable to work on

A.C. supply 50 c/s. with all internal connections,

spreader tinned copper & complete erected in

existing 16 G.M.S. housing.ICS=100% of ICU

30 Nos 4 providing and erecting Miniature circuit breaker 268.00 270.68 #NAME?

single pole 0.5A to 2A system and having

breaking capacity 10 KA to be erected in existing

box. confirming to IS 8828/1996 with ISI Mark

8 Kg 5 Providing and erecting HOT deep Galvanised 77.00 77.77 #NAME?

iron strip wire 8 to 16 SWG.

3 Nos 6 Providing and erecting Pipe type earthing with 40 815.00 823.15 #NAME?

mm dia 2.5 mtr long 'B' grade G.I. pipe with

necessary coupling buch buried in specially

prepared earth pit & G.I. earth wire of 8 SWG

erected & connected as directed (For panel)

Item SOR Rate with

Qty. Unit words Amount

No. Rate 1% L.S.

3 Nos 7 For using salt and charcoal / coke as required for 170.00 171.70 #NAME?

pipe type earthing.

3 Nos 8 Supplying & erecting earth pit of minimum bore 4546.00 4591.46 #NAME?

dia.150mm size approved make Earthing Electrode

consisting Pipe-in-Pipe Technology as per IS 3043-

1987 made of corrosion free hot dipped G.I.Pipes

having Outer pipe dia of 50mm having 80-200

Micron galvanising, Inner pipe dia of 25 mm having

200-250 Micron galvanising, connection terminal dia

of 12mm with constant ohmic value surrounded by

highly conductive compound with high charge

dissipation suitable for following type of applications

with chamber and heavy duty cover.(approved make

OEM has to submit test certificate) & having back

filling compound of (B) Inner chemical (CCM

Compound)- Resistivity:- 0.2 / meter testing as per

IEC 62561-2017, Voltage drop:- < 1 volt at no load &

dry form, Sulphar content:- <2%(C) Back fill

Compound :- Earthing compound should be capable

to retain moisture for long time Necessary test report

must be submitted. (a) For Electrical Installation up to

440V in normal soil Length of pipe - 1 Mtr Back

filling compound - 1 Nos Bag of 15 Kg.

815 Mtr 9 Replacing old & u/s by Providing and erecting 152.00 153.52 #NAME?

XLPE (IS:7098)(I)-88 ISI armoured cable

multistrand Aluminium conductor for 1.1 KV. to

be laid on wall with necessary clamps or in

existing trench / pipe of following size of cables

(A) 4 core 16 Sq. mm

775 Mtr 10 Making trench in Hard Murrum / Tar Road of 74.00 74.74 #NAME?

suitable width of 90 cm or required depth for

laying any size of cable or locating the fault all

over the run and back filling the same and

making the surface as normal ground.

Item SOR Rate with

Qty. Unit words Amount

No. Rate 1% L.S.

775 Mtr 11 Providing & laying approved make Double 62.00 62.62 #NAME?

walled corrugated pipes (DWC) of

polyethylene(conforming to IS 14930 II )with

necessary connecting accessories of same

material at required depth in existing trench for

laying of cable. below ground / road surface for

enclosing cable (A)50 mm outer dia

6 Nos 12 Providing and, fixing heavy duty flange type 47.00 47.47 #NAME?

brass cable gland with rubber ring for PVC

insulated armoured cable complete with out going

tails, insulating tape etc for following size of

cables. (D) 2 to 4 core 16 Sq. mm

24 Nos 13 Solder less crimping type Aluminium lugs 15.00 15.15 #NAME?

conforming to IS suitable for cable of following

size evenly crimped with high pressure tool &

connected to switchgear terminals with

brass/cadmium plated nut bolts in an approved

manner. (C) 16/25 Sq.mm.

I/We am /are willing to carry out the work at…………% above/below percent (should be written in figures and

words) at the estimated rates mentioned above amount of my/your tender works out as under.

*Estimated Amount *Estimated Amount

put to Tender Rs. 590772.23 put to Tender Rs.

Deduction …………….. % below………………… Add ………… % above Rs. …………….

Less Dismental 0.00 Less Dismental

The rates are inclusive ofall taxes, transport charges,storage Charges except GST and applicable

GST Will be paid.(Add GST Extra)

The materials covered under contractor should be got approved from the Deputy Executive

Engineer. In chargeof the work

The materials and work shall have to be used and carried out as specification in technical

All Works Shall be Carried Out as per Public Works Department hand book and Other

Specification Of The division or as directed

Rate are Inclusive Of 1% Labourcess in Tender amount so 1% of total amount of bill will be

Rate are Inclusive Of 1% Labourcess in Tender amount so 1% of total amount of bill will be

deducted from the bill

Note-6TheMaterial to be used in this work should be approved strictly from engineer-in –charge /Deputy

Ex. Engineer as applicable.

Note-7The Agency will have to agree to carry out the work as per brand demand of concern deptt.

Note-8An amount of Rs.0.00 (Rs.Nill only ) towards estimated credit value of dismantled materials shall

be recovered from the 1st R.A. Bill of this work.

Signature of Bidder Deputy Executive Engineer

Electrical (R&B) Sub-Division