PROVN OF HARD STANDING FOR PARKING OF VEHS AT 7 COMPO PL, ASC RAIWALA AND 01 X TOILET WITH SOCKEGE PIT AT ARMY ENVIROMENT PARK AND TRAINING AREA (AEPTA) (196 FD REGT) AT RAIWALA MIL STN

Amount

M&L for excavation in over areas not exceeding 1.50 mtr deep getting out in any type of soil all as specified and directed.

M&L for removing excavated material (soil) and depositing at a distance n. exc 50 Mtr at a level n exc 1.5 m above the starting point all as specified and directed.

M&L for Hardcore of gauge n exe 63 mm of broken stone / boulders, deposited, spread and levelled in layers n.exe 15 cm thick, watered and rammed to a true surface all as specified and directed.

M&L for PCC 1:4:8 type D2 (using 40 mm graded stone aggregate) as in sub base of flooring/ hard standing laid to a true surface all as specified and directed.

Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-40 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc.,of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of course sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete

Preparation newly or previously untreated concrete surface of any desciption surfaces exc. 10 cm width or girth and applying two coat of synthetic enemelled paint of any tint over a coat of primer incl. all preparation complete all as specified and directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m deep for foundation ,etc and getting out in soft/disintegrated soil complete all as specified and as directed.

M & L for Plain Cement Concrete Type D2 1:4:8 (using 20 mm graded stone aggregate) in foundations, filling and mass concrete.

Brick work with sub-class `B' bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:6

Brick work with sub-class `B' bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:6

M & L for 40 mm thick Cement Concrete M-15 Nominal Mix (using 12.5 mm graded stone aggregate) as in damp proof course (DPC) to horizontal or vertical surfaces including necessary form work and mixing of water proofing compound as per manufacturer’s instructions complete all as specified and directed. NOTE: - water proofing compound will be measured and paid separately.

Supply only water proofing compound (WPC)

M&L for Hard core of gauge n exc 63mm thick of broken boulder spread leveling watering ramming to true surface complete all as specified and directed by Engr-in-Charge..

M&L for 75 mm thick P.C.C 1:4:8 type B-2 using 40mm graded stone agg as in sub base of floor complete all as specified and as directed

M&L Non skid ceramic coloured tiles 7 to 8 mm thick (Square/ractangular )area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement.over and incl 15mm thick screed bed or bedding in CM 1:6 complete all as specified and as directed cement to match complete all as specifed and as directed

M&L for 300x450x7 mm thick glazed cloloures ceramic tiles as in dado incl 10mm thick back coat in CM 1:6 etc. set and jointed in neat cement slurry and pointed in coloured cement with pigment.

M&L Rendering 15 mm thick on fair faces of brick work or concrete walls surfaces in CM 1:6 finished to even & smooth without using extra cement.

M&L Rendering 15 mm thick on fair faces of brick work or concrete walls surfaces in CM 1:4 finished to even & smooth without using extra cement.

Material & Labour for two coat of cement base paint on new plastered surface over one coat of primer including preparation of surface complete all as specified and as directed by Engr-in-Charge.

M&L for preparing newly plastered surfaces of walls and applying three coats of white wash.

M & L for providing reinforced cement concrete B0 1:2:4 Nominal Mix using 12.5mm graded stone aggregate as beams , cantilevers, bressummers , lintel over 1.5 mtr span complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

M&L RCC 1:2:4 type B1 (using 20mm graded aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves etc.

Fair finished flat Form work to soffits of suspended slabs such as roof slabs, floor slabs and similar work not exce 200 mm thick.

Form work rough finished surfaces of concrete to sides and soffits of beams , lintel and similar items complete

M&L for mild steel TMT bars10mm dia, cut to length, bent to shape required including cranking bending spirally & binding with and in including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for mild steel TMT bars 6mm to 8mm dia, cut to length, bent to shape required including cranking bending spirally & binding with and in including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

S & F Soild PVC Door frame of size 50 mm x 47 mm made out of 5 mm palin colour PVC sheet reinforced with MS square tube, suppling and fixing in opening as per specification and drawing

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails. M.S frame shall bw covered with heat moulded plain colour PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and botom rail on either side & as gap insert for tip rail & bottom rails; Panelling of plain colour PVC sheet to be fitted in the MS frame weloded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement. suppling and fixing in the frame at site as per specification & drawing

M&L Second class hard wood plain, solid, straight chowkats (SAL) and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints.Complete all as specified and directed by Engineer-in-charge

S & F 30 mm thick Second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (with sash bars), edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass etc. for windows and ventilators etc

Glazing with figured glass (Frosted), pin head type, 4 mm thick and glazing with oil putty or aluminium or PVC beading in squares not exceeding 0.5 Sq.m in each pane.

S & F 100 mm long Aluminium, anodised, barrel tower bolts of extruded section

S & F 100 mm long extruded Aluminium alloy anodised Butt hinges with galvanized mild steel hinge pin type C 21.

S & F 75 mm long extruded Aluminium alloy anodised Butt hinges with galvanized mild steel hinge pin type C 21.

S & F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised.

Supply and fix 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy.

Preparation of New wood and wood based surfaces of any description not otherwise described over 10 cms width or girth and applying 2 coats of synthetic enamel paint over a coat of pink primer.

M&L cement concrete 1:3:6 type C-2 (using 20mm graded aggregate) 75 mm thick as in plinth protection surface finished even and smooth without using extra cement complete all as specified and directed.

S&F Wash basins (Padestal pattern) 550x400mm vitreous china (flat back type) any size incl cutting for and pinning in end of brackets for erecting stand but exclusive of fixing of supply and waste pipe but including waste fitting

S & F 15 mm bore Stop valves (angular stop cock), cast copper alloy, fancy type, chromium plated with long shank and cup screwed down high pressure with crutch or butterfly handle or concealed screwed both ends for iron pipe or for unions

S & F 15 mm bore chromium plated bib taps, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule

S & F 15 mm bore pillar taps, Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe.

S&F Swivel shower of PTMT any colour for fixing with 15mm pipe. (Minimum weight 40gms)

S&F Vitreous china Squatting pan , 'Orissa pattern, size 580x440 mm white, with integral foot rest excluding flushing cistern and flush pipe including connection to trap, to flushing pipe, anti-syphonage pipe, etc complete including making good to floor .

S&F PVC valveless, syphonic action type flushing cistern (Dual action ISI Marked), low level , white, with inlet ball valve, float and handle including brackets and flush pipe suitable for IWC of polyethylene of low or high density or PVC 32 mm dia for low level cistern for 10 litres capacity of approved make .Complete all as specified and directed

S&F PVC connections 15mm size with PTMT nuts of length 600mm

S&F 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed.

S & F 110 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints laid in trenches or in floors.

S & F 110 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints fixed to walls.

S & F 75 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints fixed to walls.

S & F 110 mm bore PVC (SWR) bends of any radius with access door.

S & F 110 mm bore PVC (SWR) junction single (Single `T') equal or unequal with access door.

S & F 75 mm bore PVC (SWR) Vent Cowl

S&F 15 mm GI tubing medium grade with all fixed complete to walls and ceilings or laid in floors all as specified and directed by Engr-in-Charge.

S&F Rotational moulded polyethylene water storage tank 500 liters capacity, white triple layer construction (cylindrical vertical closed top), hoisted & fixed in position including all fittings complete all as specified and as directed.

S&F 20mm dia ball valve high pressure PTMT with epoxy coated aluminium rod & high pressure plastic ball screwed for iron pipe and fixed.

S & F for Vitreous China Half stall urinal complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement,

S&F for Brass CP urinal spreader fixing with 15 mm dia pipe.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall , fixed with self tapping screws complete all as specified and directed .

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall and gutter, fixed with self tapping screws complete all as specified and directed .

S & F Rolled Mild Steel sections confirming to Fe 410 - W as in main and cross beams, hip and jack rafters; purlins where connected to common rafters fixed with angle cleats or other connecting plates

Preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer.

Returning, filling in, including spreading, levelling , watering, and well ramming in layers n.exc 25 cm thick complete all as specified and as directed

Removing excavated material (Soil) to a distance n. exc 50m and depositing where directed at a level n. exc. 1.5m above the starting point complete all as specified and as directed.

M&L Concrete bed to drain pipe 110mm dia incl. packing under and haunching against the sides of pipe PCC 1:4:8 type D2

Material & Labour for Point Wiring for one light Point/fan point controlled by one switch with 1100 volts grade single core conforming to (IS:694 /1990) PVC insulated unsheathed 1.5 sqmm multi stranded copper conductor cable (FRLSH) with contineous earth wire of 1.5 Sqmm stranded copper conductor cable (FRLSH) PVC insulated unsheathed , drawn in and including concealed PVC conduit,medium grade(ISImarked) ,duly concealed on wall/ceiling or above false ceiling with fittings not less than 20 mm dia medium grade (Color coding of wires shall be Phase, neutral and earth wire all as specified ) sunk Metal flush box with and incl decorative polycarbonate frame for housing Modular Switches, sockets , fan regulators etc including white cover plate complete all as specified and directed. Note:- i) Cost of cutting chases of suitable girth where required on brick /concrete surface and making good disturbed surface shall be deemed to be included in quoted rates. ii) If the contractor fail to make good the disturbed surface of wall/ceiling etc and do not match with the existing surface of wall/floor to the entire satisfaction of Engr-in-Charge a recovery @ of Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute the decision of accepting officer will be final and binding.

All as per above item No.2 but One 3 pin/5 pin 5/6 Amps socket outlet on same board with other switches, with cables 1.5 Sqmm size, complete all as specified and directed.

All as per above item No 2 but for One 3pin/5pin 5/6 Amps socket out let on independent board with other switches, with cables 1.5 sq mm size, complete all as specified and directed .

All as per above item No.1 above but with 2.5 Sqmm PVC insulated FRLSH cable for 15 Amps power point with contineous earth wire of 2.5 Sqmm complete all as specified and directed .

S & F switch Modular single pole, one way 6 Amps , 1 module, 230 volts, 50 hz all as specified and directed by Engr-in-Charge.

Supply and fixing switch modular , one-way 16Amps, 1 module 240 Volts AC all as specified and directed by Engr-in-Charge.

Supply and fix Modular Socket outlet, 6A - 3 pin, 2 module ISI marked, 230 volts, 50 hz all as specified and directed by Engr-in-Charge.

Supply and fixing modular socket, 6A/16A -2/3 pin combined 2 module 230 volts, 50 hz all as specified and directed by Engr-in-Charge.Make:

Supply and fixing ceiling rose surface bakelite 65/25 mm dia having three terminals all as specified

Supply and fixing in repair Fancy angle holder Metal ring insulated body with back plate, suitable for batten fittings all as specified and directed.

Supply and fix surface mounted LED luminiare, 20 watt with all accessories having polymer extruded channel with diffuser for glare free light, high lumen output, driver PF >0.90 having over voltage protection upto 400 volts surge protection, level 7-10 KV thermal short circuit protection THD<10%, made up of long life LED chips (SMD) in modular with Ra>70 and lumen efficiency >100 lumen per watt, internally pre-wired through flexible wire connecting with ceiling rose all as directed.

Supply and fix LED building security light 1 x 20 W housing made out of pressure die-cast aluminium alloy with toughned glass, IP 66 protection working on 240 volts, 50 Hz, consisting of reflecting lamps wired with appropriate driver PF> 0.98 having overvoltage protection upto 440 volt, surge protection level > 10 KV, thermal short circuit prtection THD< 10% made up of long life LED chip (SMD) in modular with Ra< 70, and LED lumen efficiency > 140 lumen per watt, beam angle along the drive way, 120 degree, beam angle across the drive way, 80 degree luminaire efficiency> 120 luminous /watt power LED should be of more than 01 watt CCT should be between 5700° K- 6500 K including bracket including neccesay modification if any and making necessary electric connection with 1.5 sqmm , 3 core, PVC insulated copper onductor cable 1100 Volt grade complete all as specified and as directed by Eng-in-Charge

S & F Fresh air fan AC single phase 230/240 Volt of size 300 mm sweep, metallic body powder coated painted finish, power consumption-50 W, Air displacement- 1290/Cum/Hr, RPM-900 complete with louvers including making whole and grouting of nut bolts etc and making good the disturbed surfaces of wall complete all as specified and directed.

Supply and fixing sheet metal enclosure double door type for MCBs DB SPN(Single pole and neutral) 240V AC 8 way with 200 Amps rated bus bar all as specified and directed .

Supply and fixing MCB SPN 6 to 32 Amp 240 V AC 10 KA 'C' Curve repturing capacity all as specified.

Supply and fixing MCB SP 6 to 32 Amp 'C' series 10 KA repturing capacity complete all as specified.

Material & labour for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground. ( earth pit not less than 2.25 mtr depth below ground level at any type of strata ) with top edge of the earth plate not less than 1.5mtr below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15cm all around the plate. connected by 4 mm GI wire as earth lead by means of brass nuts and bolt,thimbles check nuts, washers including concrete chamber of PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish, internal surface of concrete chamber shall be given internal dia 300mm x300mm, 15mm thick plaster in CM 1:4 funnel with wire mesh, RCC pit cover of 320x320x80mm size (1:2:4) Type B1 using 20mm graded stone aggregate rainforced with XPM all as shown in electrical plate No 3 of MES SSR Part-1(2009) and specified including and provision of GI wire upto 7.5 mtrs long with 15 mm dia light grade Gi pipe protection and watering pipe of GI 20 mm bore, medium grade, including all exavation and earth work and connecting the earthing wire to panel, including testing on completion complete all as specified and directed by Engr-in-charge. Note:- (i) RCC pit cover shall be precast of RCC(1:2:4) type B1, 80mm thick reinforced with XPM weighing not less than 4kg/sqm in lieu of CI cover. (ii) Cost of additional GI wire more than 7.5 mtrs will be measured and paid seperately under relevant items.

Supply and laying , fixing or passing through pipe, laid in trenches or fixed to pole/wall or fixed to LT panel board, insulated, armoured heavy duty electric cable with aluminium conductor, XLPE , 1100 volts grade, cross-sectional area of size 16 Sqmm sqmm 2 core with all as specified and directed. by Engr-in-charge

Excavation in trenches, not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth for poles, laying of electric cable and GI tubing (where provided for protection of cables) and getting out trimming the sides, forming bottom surface to required level in any type of soil complete all as specified and as directed.

Returning, filling in , including spreading, leveling, watering and well ramming in layers not exceeding 25 centimetre thick in any type of soil complete all as specified and as directed.

Removing excavated material not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and as directed.

M&L for sand for cushioning including spreading, levelling and hand punning to underground cable in trench all as specified and directed.

Material and labour for laying un-reinforced precast concrete cable cover class LV,type-3 , flat size 450mm *180mm *40 mm.

Supply only GI tubing light grade 50mm bore, light grade as in sleeving etc laid in trenches/pole post/under culvert/under load etc for cable protection complete all as specified and directed.

nautiyalandcompany

RAMAN CONSTRUCTION CO.

TARUN ENGINEERING WORKS

Sunil Enterprises

M/S VIJAY TRADERS