SITC of IT Networking work at 6th and 11th floor, Deen Dayal Upadhyay Antyodaya Bhawan

MINISTRY OF MINORITY AFFAIRS

Sl.No. Items

DSR NDSR Remarks

Digitally signed by AMIT

Estimate for Networking Solution for MOMA

S.No. DESCRIPTION UNIT QTY DSR RATE DSR AMOUNT MARKET RATE MR AMOUNT

Supply, Installation, testing and commissioning of 10 GB - 50/125μm OM4

LC LSZH Pigtails MM 50/125mm including fiber Splicing confirming to IEC

61754-20 Type A1a.2, Multimode fibre conforms to ITU-G651, ANSI/TIA

492AAAC as requried

Supply, Installation, testing and commissioning of 10 GB - 50/125μm OM4 -

LC-LC Duplex Fiber Patch Cord - 2 mtrs. Conform to LC-IEC 61754-20 IEC

10 Type A1a.2 and Telecordia performances requirements

Supplying Installation testing and Commissioning of Small Form Factor

Supplying, installation, Testing and commissioning of following capacity 24

port Layer 2 indoor Network Switch having features and specifications etc.

as mentioned here under: At least 24 X RJ-45 Gigabit Ethernet Ports and

additional 2 X 10G Base -T with 4 X SFP Ports with non-blocking

architecture by having Switching capacity of min. 168Gbps and packet

forwarding rate of 125Mpps or higher, 16K MAC table. Console Port, USB

port, Stacking support of min. 8 units per stack. Internal dual AC Power

supply, STP, RSTP, MSTP, BPDU Filter, BPDU Restriction, Min. 9K Jumbo

Frame, LBD, IGMP Snooping V1/V2/V3, MLD Snopping V1/V2. IGMP /MLD

Groups 1K or more, IPv4/IPv6 Loopback Interface, 16 L3 IP Interface, Ipv6

39.3 ND, VRRPv3, UDP Helper, ECMP. VLAN: 802.1Ǫ, Port based, Ǫ-in-Ǫ,

Multicast VLAN, Protocol VLAN, VLAN Trunking, DHCP Snopping, Server,

server Screening. RADIUS , TACACS+ Authentication, ǪoS: 802.1P, 8

queues per port, ǪoS : WRR, Strict+WRR, WRED, 802.1p. ACL: MAC based,

IPv4C IPv6, TCP/UDP Port number, time based ACL, TFTP Client, SNMP V1,

v2c, v3, SNMP traps, RMON, DHCP server, relay, client, LLDP, LLDP-MED,

OAM, Dying Gasp, 802.3ah, sflow, RIP, OSPF v2/v3, policy based

route, SSL, SSH. 6 kV surge protection on all Gigabit Ethernet ports and on

all GE RJ-45 access ports. Certifications: UL, CE, FCC, RoHS, MTCTE,.

complete as required.

24 port PoE Layer 2 Network Switch with PoE Support of 370W or higher

39.3.1 with each copper port supporting 802.3at PoE+ min. Each 4.0 125393.0 501572.0

Supplying, installation, Testing and commissioning of following capacity 24

port Layer 3 Network Switch having features and specifications etc. as

mentioned here under: At least 20 X RJ-45 Gigabit Ethernet Ports and

additional 4 combo 10/100/1000 base-t/SFP Ports with additional 4 SFP+

ports non-blocking architecture by having Switching capacity of min.

128Gbps and packet forwarding rate of 95Mpps or higher, 16K MAC table.

Console Port, USB port, Internal AC Power supply with operating

temperature of 0 to +50 0C.

Stacking port with stacking support of minimum 8 units per stack. 48K Mac

address, 9K or more Jumbo frame, ERPS with enabling ring to converge in

less than 50 ms from node or link failure, Static routing, Static, 6to4,

ISATAP and GRE, IPv6 Neighbor Discovery (ND), BGP, ISIS, MPLS, VRRP

39.4 v2, OSPFv2/v3, PBR, Route Redistribution, RIPv1/v2/ng, IP Helper all L3 each 2.0 193791.0 387582.0

Protocols should support from day 1 for both IPv6 and IPv4, 802.1x, Port

security , Radius C TACACS+ authentication C accounting, DAD, DAI, DoS

attack prevention, SSH, Guest VLAN, IP Access List, MAC Access List.

Multicast: VLAN, PIM-SM, PIMDM, PIM- SDM, PIM-SMv6, DVMRP v3 and

MSDP, IGMP C MLD Snooping, Flow mirroring, IGMP C MLD Snooping

Ǫuerier, Per-VLAN IGMP C MLD Snooping. SNMP, Dual configurations,

Multiple images, RMON, LLDP/LLDP-MED, sFlow, DHCP/BOOTP Client,

IPv4/IPv6, Syslog server, Debug command, 802.3ah Ethernet Link OAM,

802.1ag Connectivity Fault, Y.1731 OAM, 802.1Ǫbb Priority- based Flow

Control (PFC), Dying Gasp, Cable Diagnostics , 6 kV surge protection on all

Gigabit Ethernet ports and on all GE RJ-45 access ports. Certifications: UL,

CE, FCC, RoHS, MTCTE.

Supplying, installation, Testing and commissioning of 10 Giga Bandwidth

Data Centre Network Switch of 48 port Layer 3 having features and

specifications etc. as

mentioned here under: - ToR/EOR/Core Network Switch 48x 10GbE SFP+,

6x 100GbE QSFP28, RPS, with Console Port, Management Port and 1 x USB

2.0 Type A port, The switch must provide a switching capacity of no less

than 2.16 Tbps and a forwarding rate of at least 1600 Mpps, ensuring non-

blocking performance for high-bandwidth applications. It should support hot-

39.5 swappable dual power supply modules (AC or DC) for 1+1 redundancy and each 0.0 1055981.0 0.0

load sharing, as well as hot-swappable, front-to-back airflow fan trays

with N+1 redundancy to ensure continuous availability. IEEE 802.1X

support for port-based and MAC-based authentication should be available,

along with integration for RADIUS and TACACS+ authentication services.

Guest VLANs, DoS prevention, and management access restrictions are

essential. SNMP v1/v2c/v3, syslog, sFlow, and support for autoconfiguration

via DHCP. Support for OpenFlow v1.4, Netconf/YANG, and LLDP is required

for modern network automation. Support ONIE (Open Network Install

Supplying, installation, Testing and commissioning of following capacity 48

port Layer 2 indoor Network Switch having features and specifications etc.

as mentioned here under: At least 24 X RJ-45 Gigabit Ethernet Ports and

additional 2 X 10G Base -T with 4 X SFP Ports with non-blocking

architecture by having Switching capacity of min. 168Gbps and packet

forwarding rate of 125Mpps or higher, 16K MAC table.Support of 370W or

MR higher with each copper port supporting 802.3at PoE+ min. each 4.0 253000.0 1012000.0

Digitally signed by AMIT

S.No. DESCRIPTION UNIT QTY DSR RATE DSR AMOUNT MARKET RATE MR AMOUNT

Supplying and drawing following core Multi mode Fiber Optic Cable having

corrugated steel armoring, leser optimize 50/125 µm with HDPE jacket,

LSZH (Low smoke Zero Halogen), Tight-buffered or loose tube, maximum

attenuation: < 3.5 dB/km at 850 nm, < 1.5 dB/km at 1300 nm, bandwidth

> 2000 MHz-km at 850 nm, > 500 MHz-km at 1300 nm compliance and

certifications: ISO/IEC 11801 Ed. 2.2, ANSI/TIA-568- C.3, ITU-T G.651.1

RoHS compliant. Multi Mode Fiber shall be Central-loose tube filled with

Thixotropic jelly,

duly following Standards: ISO 11801, IEC 60793- 1/60794-1-2, ITU-T-REC

G.652D and Telecordia GR20-core, High quality Electro Chromium Coated

Corrugated Steel tape (ECCS ) and HDPE- Sheath, Operating ambient

Temperature should be – 5 0C to +50 0C and Storage Temperature should

be – 5 0C to +50 0C, Maximum Attenuation ± 3.5 dB/km at Operational

Wavelength 850 nm and ± 1.5 dB / km at Operational Wavelength 1300

nm . type of fiber should be 50/125 / G.652D & Refractive Index should be

1.483/1.478, The value for Mode-filed,Cladding Diameter 50 ± 2.5 µm and

125 ± 1µm correspondingly i/c splicing & marking etc complete as required.

12 Core Multi Mode Optical Fiber Cable

Supply and fixing following port Rack Mount loaded LIU with pigtail, Front-

mounted cable saddles for jumper management, suitable to manage both

splices and terminations, Pre-assembled shelves in multiple configurations,

Rubber fiber slotted bracket built-in, metal splice shelf to protect the fibers,

2 fiber spools built-in for 900μm tight buffered fiber storing, Capable of

39.21 storing up to 3 meters of 900μm tight buffered fiber per adapter,

Removable front and rear covers for better access to interior of LIU, Should

be Single / Multi mode LC Type fully loaded. Accessory kit consists of cable

ties, mounting ear screws, and spiral wrap tube etc complete as required.

Supplying, drawing, Testing and commissioning of Cat6A UTP 4 pair, 23

AWG solid copper cable in existing conduit/ on surface, U/FTP, LSZH,

NonPlenum, Horizontal (solid) Cable suitable for high speed data

networking application supporting upto 10Gbps over a 100 meter channel.

The 4 Unshielded Twisted Pairs (UTP) cable with color coded insulation for

easy indentification should have FLAMEPROPERTIES i.e. Flammability Test -

IEC 60332-1, Smoke Density - IEC 61034, LSZH standards compliance:

39.18 ANSI/TIA-568 C.2, ISO/IEC 11801, IEEE 802.3an, RoHS. Delay Skew

should be < 45NS. The outer Cable Diameter should be 7.5 + 2 mm. Cable

should have been tested and verified by UL/ ETL etc.

complete as required.

Supplying, Installation, Testing and commissioning of CAT6 Copper

Information Outlet (IO) with face plate of color as per site requirement,

should have ETL/UL verification program certificate for compliance

39.14 withANSI/TIA-568.2-D. All copper Cable and Components should be from each 300 212 63600

same OEM to maintain compatibility and interoperability etc. complete as

Supplying, Installation, Testing and commissioning of RJ45 Connector for

CAT 6/6A Cables. RJ45 modular plug supports 4 twisted pairs, 8 positions,

8 connectors. Housing: PC, UL94V-2, transparent color, Use for 24- 26

AWG stranded wires etc. complete as required.

Supplying, Installation, Testing and commissioning of following CAT6 Patch

Cord should have ETL/UL verification program certificate for compliance

39.12 with ANSI/TIA-568.2-D etc. complete as required.

Supplying and fixing of following size Wall Mount Rack having Fixed

Structure with 0.8mm CRCA Sheet, completely knocked-down condition

(CKD) Shape, Vertical Mounting Rail 1.6 mm with 'U'Marking, Minimum 2

cable entry/exit provision at Top and bottom with rubber protection, Front

39.23 5mm Toughened Glass with lock, wall mounting kit Powder coated Color-

RAL- 7035, complied with UL & RoHS, 2 x 6 sockets 16A power distribution

units, 3 numbers closed cable organizer, Hardware mounting screws packet

of 20 x 1 number, etc. complete as required.

GYPBOARD CEILING :- Providing and fixing false ceiling at all height

including providing and fixing of frame work made of special sections,

power pressed from M.S. sheets and galvanized with zinc coating of 120

gms/sqm (both side inclusive) as per IS : 277 and consisting of angle

cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and

37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with

dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange

of cleat fixed to the angle hangers of 25x10x0.50 mm of required length

with nuts & bolts of required size and other end of angle hanger fixed with

12.45 intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 SQM 750.00 1,355.80 10,16,850.00

mm centre to centre, to which the ceiling section 0.5 mm thick bottom

wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5

mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular

to G.I. intermediate channel with connecting clips made out of 2.64 mm dia

x 230 mm long G.I. wire at every junction, including fixing perimeter

channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm

Wiring for circuit/ submain wiring alongwith earth wire with the

1.14 following sizes of FR PVC insulated copper conductor, single core

cable in surface/ recessed medium class PVC conduit

Wiring for light point/ fan point/exhaust fan point/call bell point with 1.5 sq.

mm FRLS PVC insulated copper conductor single core cable in

surface/recessed medium class PVC conduit, with modular switch, modular

plate, suitable GI box and earthing the point with 1.5 sq. mm. FRLS PVC

insulated copper conductor single core cable etc as required.

Digitally signed by AMIT

S.No. DESCRIPTION UNIT QTY DSR RATE DSR AMOUNT MARKET RATE MR AMOUNT

Supplying and fixing following modular switch/ socket on the existing

1.24 modular plate & switch box including connections but excluding modular

plate etc. as required.

Finishing with Deluxe Multi surface paint system for interiors and exteriors

13.48 using Primer as per manufacturers specifications:

Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including

Supplying and installaton following size of perforated painted with powder

coating M.S. cable trays with perforation not more than 17.5%, in

convenient sections, joined with connectors, suspended from the ceiling

with two numbers MS/GI Suspenders i/c base of suitable size MS/GI angle,

bolts & nuts, painting suspenders, fastener etc as required.

Supplying and fixing of following sizes of medium class PVC conduit along

1.21 with accessories in surface/recess including cutting the wall and making

good the same in case of recessed conduit as required.

Chipping of unsound/weak concrete material from slabs, beams, columns

etc. with manual Chisel and/ or by standard power driven percussion type

or of approved make including tapering of all edges, making square

26.28 shoulders of cavities including cleaning the exposed concrete surface and

reinforcement with wire brushes etc. and disposal of debris for all lead and

lifts all complete as per direction of Engineer-In-Charge

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5

sq.meters and under, including cutting the patch in proper shape, raking

14.1 out joints and preparing and plastering the surface of the walls complete,

including disposal of rubbish to the dumping ground, all complete as per

direction of Engineer-in-Charge.

With cement mortar 1:4 (1cement: 4 coarse sand)

Supply, Installation, Testing and Commissiong of 10 KVA with battery bank

True Online Double Conversion UPS 3Phase Input- 3Phase Output in

Parallel Redundant N+1 Configuration IGBT Based Rectifier and IGBT Based

Batteries:12 V, SMF with minimum VAH capacity suitable for 30

minutes backup with each ups Along with Accessories Rack, Interlinks, SFU,

Parallel Kit, DC Cable Upto 5 Meters complete in all respect as per the

directions of the engineer in charge.

UPS should have availability of Input /Output isolator, Inbuilt manual

bypass along with phase sequence corrector. UPS Efficiency shall not be

less than 94% from 25% to 100% Load ,

isolation etc Power factor should be more than 0.9

Designing, fabricating, transporting, unloading, storing, fixing in position,

testing and commissioning the followingsheet steel cubicle typepanels

fabricated from1.6mmthick CRCA sheet, dust and vermin proof, indoor type

TPN Panels with hinged lockable doors fabricated from 2mm thick CRCA

sheet, suitable for 415V,3 phase 4wire 50 Hz ACsupply

with rear access for cable alley and with segregated bus-barchamber with

tinned aluminium busbar and including supplying and fixing following

switch gears,meters and accessories, interconnections, bonding to

earth,powder coated painting and marking as specified.

Three(3)nos, 32 Amps. 4pole MCB, i.efour pole Moulded Case Circui t

Breaker of fault breaking capacity.

Digitally signed by AMIT