GENERAL-Renovation and Upgradation of main block of Govt. Guest house Aluva, Electrical-Mechanical-Plumbing works-MEP works-General Electrical Work

Amount

Plumbing

14.76:Cleaning and desilting of gully trap chamber, including removal of rubbish mixed with earth etc. and disposal of same, all as per the direction of Engineer-in-charge.

14.78:Cleaning of under ground sump, Over Head R.C.C. Tank ( independent staging) including disposal of slit and rubbish, all as per direction of Engineer-in-Charge. The cleaning shall consist following operations:- (i)Tank shall be emptied of water by pumping & bottom shall be cleaned of slit and other deposits. (ii) Entire surface area of the sump shall then scrubbed thoroughly with wire brush etc. and pressure washed with water. (iii) Chlorination of RCC internal surface by liquid chlorine. (iv) The treated surface shall be dried using air jetting and all loose particles shall be removal from the surface. (v) Finally the surface shall be treated with ultraviolet radiation etc. as per direction of Engineer-in-Charge.

15.52:Dismantling of flushing cistern of all types (C.I. / PVC/ Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead

17.10.1.2:Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required: Kitchen sink with drain board510x 1040 mm bowl depth 225 mm

17.3.1:Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid

17.31:Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

17.34.1:Providing and fixing toilet paper holder:C.P. brass

17.35.1.1:Providing and fixing soil, waste and vent pipes: 100 mm diaSand cast iron S & S pipe as per IS : 1729

17.7.1:Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

17.41.1.1:Providing and fixing double equal junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete: 100x100x100x100 mmSand cast iron S& S as per IS- 1729

17.42.1.2:Providing and fixing double equal plain junction of required degree. 100x100x100x100 mmSand cast iron S & S as per IS - 3989

17.45.1.1:Providing and fixing double unequal junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete: 100x100x75x75 mmSand cast iron S & S as per IS - 1729

17.49.1.1:Providing and fixing double equal plain invert branch of required degree: 100x100x100x100 mmSand cast iron S & S as per IS-1729

17.50.2.3:Providing and fixing single equal plain invert branch of required degree: 75x75x75 mmHubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905

17.53.3.1:Providing and fixing sand cast iron S & S off sets as per IS : 1729 152 mm off setsWith 75 mm dia pipe

17.60.2.1:Providing and fixing trap of self cleansing design with screwed down or hinged grating without vent arm complete, including cost of cutting and making good the walls and floors: 100 mm inlet and 75 mm outletSand cast iron S & S as per IS - 3989

17.73.2:Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighting not less than 190 gms

18.17.1:Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :25 mm nominal bore

18.17.2:Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :32 mm nominal bore

18.17.3:Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :40 mm nominal bore

18.17.4:Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :50 mm nominal bore

18.18.2:Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete:20 mm nominal bore

18.18.3:Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete:25 mm nominal bore

18.19.1.1:Providing and fixing gun metal non-return valve of approved quality (screwed end): 25 mm nominal boreHorizontal

18.19.2.1:Providing and fixing gun metal non-return valve of approved quality (screwed end): 32 mm nominal boreHorizontal

18.21.2.2:Providing and fixing uplasticised PVC connection pipe with brass unions:20 mm nominal bore

18.22.2:Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet:150 mm diameter

18.32.1:Constructing masonry chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for stop cock, with C.I. surface box 100x100x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design:With common burnt clay F.P.S (non modular) bricks of class designation 7.5

18.48A: Providing and fixing rectangular high density polyethylene water storage loft tank with cover, conforming to ISI : 12701, colour of opaque white or as approved by Engineer-in-charge. The rate includes making necessary holes for inlet, outlet & over flow pipes. The base support i/c fittings & fixtures for tank shall be paid separately.

18.50.1:Providing and fixing C.P brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.15 mm nominal bore

18.52.1:Providing and fixing C.P brass stop cock ( concealed) of standard design and of approved make conforming to IS: 893115 mm nominal bore

18.53.1:Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 893115 mm nominal bore

18.58.2.1:Providing and fixing PTMT grating of approved quality and colour. Rectangular type with openable circular lid150 mm nominal size square 100 mm diameter of the inner hinged round grating

18.62.5:Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P / H.P.H.D plastic ball.50 mm nominal bore, 242 mm long weighing not less than 1240 gms.

18.7.6:Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge. Internal work - Exposed on wall50 mm nominal dia pipes

18.8.1:Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.15 mm nominal dia pipes

18.8.2:Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.20 mm nominal dia pipes

18.8.3:Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.25 mm nominal dia pipes

18.8.4:Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.32 mm nominal dia pipes

18.9.5:Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work40 mm nominal dia pipes

19.13.1.1:Constructing brick masonry circular manhole 1.52 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement:4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 (1 cement:3 coarse sand: 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement:2 coarse sand: 4 graded stone aggregate 20 mm nominal size)finished with a floating coat of neat cement, all complete as per standard design: 2.30 m deep with SFRC cover and frame (heavy duty HD - 20 grade designation) 560 mm internal diameter conforming to IS:12592, total weight of cover and frame to be not less than 182 kg fixed in cement concrete 1:2:4 ( 1 cement:2 coarse sand: 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately):With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

19.7.1.1:Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand) with R.C.C. top with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size,) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) finished with a floating coat of neat cement complete as per standard design: Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weigh of cover 23 kg and weight of frame 15 kg):With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

19.7.3.2:Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand) with R.C.C. top with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size,) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) finished with a floating coat of neat cement complete as per standard design: Inside size 120x 90 cm and 90 cm deep including C.I. cover with frame ( heavy duty ) 560 mm internal diameter, total weight of cover and frame to be not less than 208 kg ( weight of cover 108 kg and weight of frame 100 kg)With Sewer bricks conforming to IS: 4885

19.9.1.2:Constructing brick masonry circular type manhole 0.91 m internal dia at bottam and 0.56 m dia at to[ in cement mortar 1:4 (1 cement : 4 coarse sand), in side cement plaster 12 mm thick with cement mortar 1:3 ( 1 cement: 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix ( 1 cement: 3 coarse sand: 6 graded stone aggregate 40 mm nominal size ), and making necessary channel in cement concrete 1:2:4 ( 1 cement:2 coarse sand: 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design:With Sewer bricks conforming to IS:4885

22.5:Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg /sqm mixed with water proofing cement compound @ 0.126 kg/ sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

50.18.7.3.1:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer- in- Charge 25 mm dia 12 Kgf/cm2 - Internal work - Exposed on wall

50.18.8.1.1:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer- in- Charge. Concealed work, including cutting chases and making good the wall etc. 15 mm pipe 12 Kgf/ cm2

50.18.8.2.1:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work,including cutting chased and making good the wall etc. 20 mm pipe 12 Kgf/cm2

50.18.8.3.1:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 25 mm pipe 12 kgf/cm2

50.18.8.4.2:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 32 mm pipe 6Kgf/cm2

50.18.8.5.1:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. concealed work, including cutting chases and making good the wall etc. 40 mm pipe 10 kgf/ cm2

50.18.8.5.2:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 40 mm pipe 6Kgf/cm2

50.18.8.6.1:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 50 mm pipe 10 kgf/cm2

50.18.8.6.2:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 50 mm pipe 6 kgf/cm2

50.18.8.7.1:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work including cutting chases and making good the wall etc. 63 mm pipe 6 Kgf/cm2

50.18.8.8.1:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 75 mm pipe 6 Kgf/cm2

50.18.8.9.1:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chased and making good the wall etc. 110 mm pipe 6kgf/cm2

50.18.9.10.1:Providing and fixing PVC pipes includings jointing of pipes with one step pvc solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer in Charge. 150 mm dia 6 Kgf/cm2

50.4.1.1:Providing and laying in position cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size) up to floor five level excluding the cost of centering, shuttering, finishing for leveling coarse of floor and roof etc.

50.6.1.4:Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand ) etc complete

50.6.1.8:Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x15cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level with thickness 15cm in: CM 1:6 ( 1 cement : 6 coarse sand etc complete

51.19.ST4:Supplying and installing ready made PVC Septic tank including the cost of carriage, trenching, placing at the level below ground level as specified as per the direction of engineer in charge (Provision for CC/RCC/Sand/06mm aggregate for the preparation of bed shall be paid separately) 4. 35 to 50 flush capacity

ELECTRIFICATION

1.10.3:Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group C

1.11:Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

1.12:Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

1.17.2:Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.2 x 1.5 sq. mm

1.17.3:Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 X 1.5 sq.mm

1.17.12:Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 2.5 sq. mm

1.18.2:Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor,unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.2 Pair

1.19:Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

1.21.1:Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

1.21.2:Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

1.24.3:Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 amp switch

1.24.4:Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet

1.24.5:Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 amp socket outlet

1.24.6:Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.Telephone socket outlet

1.24.7:Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.TV antenna socket outlet

1.24.8:Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.Bell push

1.25:Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

1.26:Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

1.27.1:Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.1 or 2 Module (75mmX75mm)

1.31:Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

1.33:Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

1.35:Installation, testing and commissioning of wall bracket / ceiling fittings of all sizes and shapes containing up to two GLS/CFL/LED lamps per fitting, complete with all accessories including connection etc. as required.

1.39:Providing and fixing plain 16/0.20mm (0.50sqmm) twin flat flexible, FRLS PVC insulated, copper cable, in PVC sleeve of suitable size on the floor / wall, or side of the table / door etc. as required.

1.40:Providing and fixing plain 16/0.20 mm (0.50 sqmm) twin circular flexible FRLS PVC insulated, PVC sheathes copper cable direct on the wall with PVC clips etc as required.

1.44:Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.

1.47:Supplying and fixing extra down rod of 10 cm length G.I. pipe, 15 mm dia, heavy gauge including painting etc. as required. (Note: More than 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall be ignored)

1.49:Numbering of ceiling fan / exhaust fan/ fluorescent fittings as required.

1.50.1:Installation of exhaust fan in the existing opening, including making good the damage connection testing, commissioning etc. as required.Upto 450 mm sweep

1.51:Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required

1.55.3:Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group C

1.56:Supplying and fixing suitable size Gl box with modular plate and cover in front on surface or in recess, including providng and fixing 2 Nos. 3 pin 5/6 A modular socket outlets and 2 Nos. 5/6 A modular switches, connection etc. as required. (For light plugs to be used in non residential buildings).

1.57:Supplying & fixing suitable size Gl box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required. lCD

1.14.5:Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 10 sq. mm + 1 X 6 sq. mm earth wire

2.2.14:Providing and fixing following rating and breaking capacity MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel. making connections. etc. as required. 125 Amp, 36 KA

OD8383/2025-2026:Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCBIRCCB/Isolator). 2 + 8 way, Double door

OD8382/2025-2026:Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCBIRCCB/Isolator) 2+12 way, Double door

OD8381/2025-2026:Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 4 way (4+12), Double door

OD8380/2025-2026:Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (butwithout MCB's and incomer ) as required .(Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 8 way (4 + 24), Double door

2.10.1:Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, ""C"" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

2.10.3:Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, ""C"" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Double pole

2.10.4:Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, ""C"" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole

2.10.5:Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, ""C"" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole and neutral

2.11:Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

2.12.1:Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.13.1:Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.13.2:Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

2.14.2:Supplying and fixing following rating, double pole, (single phase and neutral),240 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 milli amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

2.15.1:Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 milli Amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 25 amps

2.15.2:Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 milli Amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

2.21:Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

OD2715/2025-2026:Supply and providing 12 mm dia steel 'S' type fan hooks, on the RCC roof, making good the damages of roof etc. as required

OD2717/2025-2026:Supplying and fixing following rating, triple pole, (three phase), 415 V, miniature circuit breaker (MCB) in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A to 63 A, TP MCB (C curve)

OD2719/2025-2026:Supplying and fixing 40A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40A DP MCB

OD2920/2025-2026:Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting 125A, MCCB as incomer and SP/TP MCB's are outgoings (but without MCCBs and MCBs) as required . (Vertical type MCB TPDB is normally used where 3 phase outlets are required.)

OD17882/2025-2026:Supply, installation, testing and commissioning of 250 kVA, 415V, 3-phase, 50Hz DG set with AMF control panel, operating at 1500 rpm, improved fuel efficiency, having a heavy-duty engine with lowest noise level complete with necessary accessories and standard protections, suitable for installation as per latest CPCB and statutory norms.

OD2733/2025-2026: Supply and fixing TPN sheet steel enclosure on surface/ recess along with provision for fixing one number TPN/ 4Pole, 415 V “C” curve MCB etc. as required.

OD2734/2025-2026:Supply and installation 5KVA Online UPS: Supply, installation, testing and commissioning of 5KVA online UPS, single phase IN & single phase OUT, Low Distortion (less than 3%) High Efficiency (Output 94%) with power factor 0.98, have built in static and internal bypass (Manual and Automatic), multifunction LCD status and control console with audible alarm customized by severity and having Emergency Stop button, SMF battery, battery stand and UPS Fixing accessories having a backup of minimum 30 minutes

4.1.2:Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 150 mm width X 50 mm depth X 1.6 mm thickness

4.1.4:Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness

4.2.2:Supplying and installing following size of perforated pre-painted M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.150 mm width X 50 mm depth X 1.6 mm thickness

4.2.4:Supplying and installing following size of perforated pre-painted M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.300 mm width X 50 mm depth X 1.6 mm thickness

4.4.2:Supplying and installing following size of perforated painted with powder coating M.S. cable trays Cross Member with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 150 mm width X 50 mm depth X 1.6 mm thickness

4.4.4:Supplying and installing following size of perforated painted with powder coating M.S. cable trays Cross Member with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness

5.5:Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. (but without charcoal/ coke and salt ) as required.

5.8:Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

5.14:Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

5.19:Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

90.16.1.2:Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required2.65 mm copper conductor (12 SWG)

90.16.1.3:Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required3.15 mm copper conductor ( 10 SWG)

7.1.4:Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Above 185 sq. mm and upto 400 sq. mm

7.6.4:Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct as required.Above 185 sq. mm and upto 400 sq. mm

7.7.1:Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Upto 35 sq. mm (clamped with 1mm thick saddle)

7.7.2:Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

7.8.1:Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.Upto 35 sq. mm (clamped with 1mm thick saddle)

7.8.2:Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

7.9:Supplying and making cable route marker with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) of size 60 cm X 60 cm at the bottom and 50 cm X 50 cm at the top with a thickness of 10cm including inscription duly engraved as required.

OD17794/2025-2026:Supply of following size heavy duty XLPE insulated, and PVC sheathed armoured power cable, conductors of best conductivity aluminium, 1.1 KV grade, conforming to IS 7098 (part-I) etc., as required. 2C x16 Sq.mm

OD17795/2025-2026:Supply of following size heavy duty XLPE insulated, and PVC sheathed armoured power cable, conductors of best conductivity aluminium, 1.1 KV grade, conforming to IS 7098 (part-I) etc., as required. 4C x 16 Sq.mm

OD17796/2025-2026:Supply of following size heavy duty XLPE insulated, and PVC sheathed armoured power cable, conductors of best conductivity aluminium, 1.1 KV grade, conforming to IS 7098 (part-I) etc., as required. 4C x 25 Sq.mm

OD17797/2025-2026:Supply of following size heavy duty XLPE insulated, and PVC sheathed armoured power cable, conductors of best conductivity aluminium, 1.1 KV grade, conforming to IS 7098 (part-I) etc., as required. 4C x 35 Sq.mm

OD17798/2025-2026:Supply of following size heavy duty XLPE insulated, and PVC sheathed armoured power cable, conductors of best conductivity aluminium, 1.1 KV grade, conforming to IS 7098 (part-I) etc., as required. 3.5C x 240 Sq.mm

OD17799/2025-2026:Supply of following size heavy duty XLPE insulated, and PVC sheathed armored power cable, conductors of best conductivity aluminium, 1.1 KV grade, conforming to IS 7098 (part-I) etc., as required. 3.5C x 70 Sq.mm

9.1.3:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.2 X 16 sq. mm (22mm)

9.1.23:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 70 sq. mm (38mm)

9.1.29:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 240 sq. mm (62mm)

9.1.33:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 16 sq. mm (28mm)

9.1.34:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 25 sq. mm (28mm)

9.1.35:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 35 sq. mm (32mm)

OD2778/2025-2026:Supply of 30/36W 2x2 Square LED luminaire: Supply and providing recess mounted type 2' x 2' Square, 30/36 W, indirect decorative LED Luminaire with white powder coated CRCA housing, seamless front frame with white colored flat acrylic cover etc.as required.

OD2779/2025-2026:Supply of 12W Warm White LED cross laser outdoor waterproof exterior wall step up down left right light fixture waterproof lamp black or white finish etc.as required

OD2780/2025-2026:Supply of 8W Warm White LED cross laser outdoor waterproof exterior wall step up & down light fixture waterproof lamp black or white finish etc.as required.

OD2781/2025-2026:Supply of 20W LED batten/ tube light fittings: Supply and providing 20W Surface mounting type LED Lenier batten/ tube light fittings with output of 2000 lumen, made out of CRCA body with white acrylic cover etc. as required

OD2782/2025-2026:Supply of 9/12 W surface/recess LED down lighter: Supply and providing round shaped 9/12 W low glare, recess mounting type, integral LED down light fittings with white powder coated Die cast aluminium body with anodized aluminium reflector etc.as required.

OD2783/2025-2026:Supply of 18/20 W recess LED down lighter: Supply and providing 18/20 W low glare, recess mounting type, integral LED down light fittings with white powder coated Die cast aluminium body with anodized aluminium reflector etc.as required.

OD2784/2025-2026:Supply of BLDC,1200mm Ceiling Fan: Supply of 1200 mm sweep, BLDC Electric Ceiling Fan, White Colour, with double ball bearing, shackles, 300 mm down rod, canopies, blades, suitable for operation on 220/ 240V, 50 Hz, single phase AC supply etc. as required.

OD37624/2025-2026:Supply of 305mm Exhaust Fan: Supply of 300/305 mm sweep light duty exhaust fan in metal frame suitable for operation on 220/ 240V, 50 Hz, single phase AC supply etc. as required.

OD2787/2025-2026:Supply of 7W recess LED down lighter: Supply and providing round shaped 7W, recess mounting type, integral slim LED down light fittings with white powder coated Die cast aluminium body with anodized aluminium reflector etc.as required. (Make: Philips Dura Slim, Crompton, Wipro)

OD2788/2025-2026:Supply of 22W recess slim LED down lighter: Supply and providing 22 W, recess mounting type, integral slim LED down light fittings with white powder coated Die cast aluminium body with anodized aluminium reflector etc.as required. (Make:Philips Dura Slim,Crompton,Wipro)

OD2789/2025-2026:Supply of 10W, integrated LED, Outdoor Wall Light (IP65 ), poly carbonate body, acrylic glass cover, 900 lumens, dust proof and water resistant, etc as required.

OD2790/2025-2026:Supply of LED Spherical Crystal Flush Mount Chandelier light fittings, not less than 15" width, metal base plate, inbuilt LED etc as required.

OD2791/2025-2026:Supply of 7W inbuilt LED Picture wall light, 230V, Die-casted aluminum body, not less than 250 lumen output, not less than 35 Cm in length, etc as required.

OD2792/2025-2026:Supply of 5W, integral LED Lenier batten lights, CRCA/Polycarbonate body with acrylic cover etc as required

OD2794/2025-2026:Supply of elegant gold color finish retrofit LED interior wall light fittings, having single E27 bulb holder, designer glass cover, including retrofit LED lamp of 12W etc as required.

OD2795/2025-2026:Supply of 7/12W dimmable and touch sensing smart LED bed side table lamp etc as required

OD2797/2025-2026: Supply and providing 3/5 W, LED foot lamp, 3/4 module along with 3/4 module GI box connection testing etc. as required.

OD2888/2025-2026:Supply and installation of 2 module modular ding-dong bell on 2 module cover plate and GI box complete with connections, testing and commissioning etc as required.

OD2889/2025-2026:Supplying and fixing two module external DND & MMR control unit with bell push on 2 module modular plate & switch box out side the room and two module internal DND & MMR control unit inside the room including connections etc. as required

OD2890/2025-2026:Supply installation, testing and commissioning of modular addressable bell call indicator system with register for 15 rooms including connections etc as required

OD2892/2025-2026:Supply, installation, testing and commissioning of 15A, 230V, modular, key card switch with time delay, 2 Module, include key fob etc as required

OD2893/2025-2026:Supply installation testing and commissioning of MCB DB compatible 40A three pole & neutral power contactor with 4 Nos NO contacts etc as required.

OD2894/2025-2026:Supply installation testing and commissioning of MCB DB compatible 40A single pole power contactor with 2 Nos NO switches etc as required.

OD2895/2025-2026:Supply, installation, testing and commissioning of Premium Looking White & Golden LED Backlit Name/ number Plate of size 8 inches (H) & 12 Inches (W), made out of Vinyl and Crystal Clear Acrylic Sheet of 3 mm Thickness, letters are 3mm embossed up from surface, Letter are made from 3 mm thick Golden color with mirror shine Acrylic sheet, the Copper shine and color of names shall not fade or become dull with time, nameplates shall be waterproof but also sustain sunlight, Imported warm white LED Lights Installed, durable & reliable, the material used shall be of UV, moisture and termite resistant, etc infront of the main doors of Guest rooms etc as required.

OD2911/2025-2026:Providing first aid box as approved by St. John Ambulance Brigade/ Indian Red Cross conforming to IS 2217 : 1963

OD2912/2025-2026:Providing of set of 4Nos GI bucket painted in post office red colour with prior coat of red oxide paint and written with white paint 'FIRE' and mounted on MS angle iron frame with bracket of appropriate size & capacity including filling sand etc as required

OD2913/2025-2026:Supply and fixing safety instruction chart in word duly framed with 5mm thick glass as required (approx. front area 1.20 Sq.mt.)

OD2914/2025-2026:Supply and Installation of 6kg Dry Chemical Powder type (DCP) fire extinguishers having ISI mark along with mounting supports etc. as required

OD2915/2025-2026:Supply and providing suitable size GI checkered plate over the trench including supply and providing of necessary angle iron frame work support & 'C' channel and related civil works etc. as required.

OD2916/2025-2026:Supply and providing one number of 2m x 1m x 12mm size, to withstand 3.3 KV dielectric strength, rubber mat (IS:5424 / 1969) in front of the main switch board.

OD2917/2025-2026:Supply and fixing shock treatment chart duly mounted on a wooden frame with 5mm thick glass as required (approx. front area 1.20 Sq.mt.).

OD2918/2025-2026:Preparation of necessary forms, documents drawings etc. with necessary certifications & test reports and procuring approval and energization certificate from Kerala state Electricity Board / Electrical Inspectorate including all miscellaneous expenses and all related expenses & formalities shall be met by contractor but excluding statutory charges, cash deposit etc.

ELV works

OD4085/2025-2026:Supply, installation, testing and commissioning of 24 PORT cloud-managed layer 2+ Ethernet Switch, consisting of 24 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10 BASE-T, IEEE802.3u Type 100 BASETX, IEEE 802.3ab Type1000 BASE-T), Duplex: 10 BASE-T/100 BASE-TX: half or full; 1000 BASE-T: full only; 4 SFP+ 1/10 GbE ports, 128 Gbps switching capability and delivers advanced functionalities including customizable like VLANs, link aggregation, SpanningTree Protocols, and Enhanced security features such as IEEE 802.1X access control, Automatic denial-of-service (DOS) monitors and protects the network againstmalicious attacks. power 200 - 240 VAC (50/60 Hz). Make: HP-ARUBA/ CISCO/Equivalent

OD4086/2025-2026:Supply, installation, testing and commissioning of 24 PORT POE cloud-managed layer 2+ Ethernet Switch, consisting of 24 RJ-45 autosensing 10/100/1000 Class 4 PoE ports(IEEE 802.3 Type 10 BASE-T, IEEE 802.3u Type 100 BASE-TX, IEEE 802.3ab Type 1000 BASE-T), Duplex: 10 BASE-T/100 BASE-TX: half or full; 1000 BASE-T: full only; 4 SFP+ 1/10 GbE ports, PoE capability: 195 W Class 4, 128 Gbps switching capability and delivers advanced functionalities including customizable like VLANs, link aggregation, SpanningTree Protocols, and Enhanced security features such as IEEE 802.1X access control, Automatic denial-of-service (DOS) monitors and protects the network againstmalicious attacks. power 200 - 240 VAC (50/60 Hz). Make: HP-ARUBA/ CISCO/Equivalent

OD3776/2025-2026:Supply, Installation, Testing & Commissioning of 12 Port OS2 LIU Fully Loaded- with below specifications, Flange Mount Quad LC Couplers with 6 Coloured Pigtails for core identification, Type: Fixed Type 1U Maximum Supporting 48 LC Ports, Material: Cold Rolled Steel (CRS), Cover: 16 Gauge, Fiber Termination: Direct Termination, RoHS Compliant, Should include Splice Trays , Glands and Blank Inserts to cover unused prots as required. Make: COMMSCOPE/ MOLEX/ LEGRAND.

OD3777/2025-2026:Supply, Installation, Testing & Commissioning of Fibre optic patch cords of 1 Meter below specifications as minimum, Type: OS2 Bend Insensitive Fiber, Durability: 500 insertions, Operating Temperature: -40°C to +85°C, Connector Type: Duplex LC to LC, Sheath: LSZH. Make: COMMSCOPE/ MOLEX/ LEGRAND.

OD3778/2025-2026:Supply, Installation, Testing & Commissioning of Cat6 Information Outlets Contact Plating: 50μ” Gold/50μ” Nickel Minimum, RJ-11 compatible, Plastic Housing: Polycarbonate, UL94V-0 rated or equivalent, Durablity : Minimum 20 Reterminations, Dust covers to protects from dust and contaminants, ETL 4 Channel Connector Tested, Contact Resistance: <20MΩ, Insulation Resistance: >100MΩ Min, RoHS Compliant. Make: COMMSCOPE/ MOLEX/ LEGRAND.

OD3779/2025-2026:Supply, Installation, Testing & Commissioning CAT6 Patch Cord of Length : 1 Meter Conductor Size: 24 AWG stranded bare copper wire, Sheath: LSZH, Operating Temperature range : -20°C to +70°, MIN operating life: 750 insertion cycles, ETL 4 Channel Connector Tested, RJ45 plug and boot material: Clear polycarbonate, Contact material: 0.35mm thick copper alloy, Contact plating: 1.27um gold, Max voltage: 150 VAC, Max current: 1.5A @ 25°C. Make: COMMSCOPE/ MOLEX/ LEGRAND.

OD3780/2025-2026:Supply, Installation, Testing & Commissioning of 1U 24 Port CAT6 Patch Panel Fully Loaded, Contact Plating: 1.27 micrometres Au/Ni, Individually removable patch panel ports, RJ-11& RJ-12 compatible, Plastic Housing: Polycarbonate, UL94V-0 rated or equivalent, Operating Life: Minimum 750 insertion cycles, Durablity : Minimum 200 Reterminations, Dust covers to protects from dust and contaminants, ETL 4 Channel Connector Tested, Contact Resistance: <20MΩ, Insulation Resistance: >100MΩ Min, Material: Black Powdercoat CRS (cold rolled steel) Thickness Min: 1.52mm (.060”), Front and rear port labeling as well as panel identification label, RoHS Compliant. Make: COMMSCOPE/ MOLEX/ LEGRAND.

OD3781/2025-2026:Supply, Laying, Testing & Commissioning of CAT6 U/UTP 23 AWG LSZH cable with specifications as minimum in concealed system/cable trays using knockouts for connecting conduits, cables and ties etc as required. Conductor Size: 23 AWG, Sheath Type : LSZH 332.1, Characteristic Impedance: 100±15Ω, Conductor Resistance: ≤9.38Ω/100m, Mutual Capacitance: <5.6nF/100m, Resistance Unbalance: 5% Max, ETL 4 Channel Connector Tested Freequency Verified upto 650 Mhz (Min), Delay Skew: <45nS, Operating Temperature range : -20°C to +70°, NVP:67%. Make: COMMSCOPE/ MOLEX/ LEGRAND.

OD3782/2025-2026:Supply and Installation of 6 Core OFC HDPE Gell Filled tube Armoured Fiber Cable on wall surface as required (clamped with 1mm thick saddle)with specifications as follows: Outdoor OS2 Fiber with Fibre Identification: Colour Coded, Water Blocking: Thixotropic Gel (Tube) Petroleum Jelly (Interstices), Core Wrapping: Polyester tape / Water swellable tape, Armoring: Corrugated Steel Tape Armor(ECCS Tape) Thickness > 0.125mm, Peripheral Strength Member: Two steel wires min 0.9 mm diameter, Ripcord: Polyester based yarns below armored tape for easy ripping, Outer Sheath: UV Stabilized Polyethylene (HDPE) , Anti-Rodent , Anti-Termite, Tensile Strength Min: 1500N, Crush Resistance Min: 3000N/10CM, Operating Temperature range : -40°C to +70°; Make: COMMSCOPE/ MOLEX/ LEGRAND.

OD3783/2025-2026:Supply and installation of 1.25Gd SFP Module Single mode 1310 nm1000 Base LX/LC connector. Make: Netgear/Cisco/Ruckus

1.21.1:Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

1.21.2:Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

1.21.3:Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.32 mm

1.27.1:Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.1 or 2 Module (75mmX75mm)

1.28.1:Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.1 or 2 Module

90.12.10.2:Supply & laying of DWC pipe in ordinary soil 0.75m below ground level including excavation50/38 mm or nearest size

90.12.9.2:Supplying, laying and jointing of the following sizes of double wall corrugated (DWC) pipes made out of HDPE conforming to IS 14930 Part II for mechanical protection to underground power cables with all required accessories in ground in the existing trench50/38 mm or nearest size

90.6.9.7:Supplying & Drawing unarmored PVC insulated and & PVC sheathed copper conductor Telephone Pair Cable conforming to ITD specification for indoor application through the existing conduit20 pair

OD3800/2025-2026:Supply, Installation, Testing & Commissioning of Firewall with upto 90 concurrent users and harware with minimum specifications, 22 x GE RJ45 ports (including 2 x WAN ports, 1 x DMZ port, 1 x Mgmt port, 2 x HA ports, 16 x switch ports with 4 SFP port shared media), 4 SFP ports, 2x 10G SFP+ FortiLinks, dual power supplies redundancy and with 3 Year Unified Threat Protection (UTP) (IPS, Advanced Malware Protection, Application Control, URL, DNS & Video Filtering, Antispam Service, and Premium features) FortiGate-100F.Make: Fortinet/ Cisco/ Paloalto

OD3801/2025-2026:Supply and installation of Weatherproof IP65 3x3 PVC co box for fixing CCTV

OD3808/2025-2026:Supply, Installation, Testing & Commissioning of 10TB 3.5" SATA 6Gb/s 256MB Cache 7200RPM Surveillance Hard Disk Drive with health management, helping to monitor and maintain the drive's performance and reliability over time, with 5 year warranty. Make: WD/ Seagate Equivalent

OD3883/2025-2026:Supply and providing telephone junction box 100 Pair with hinged doors fabricated out of No. 16 SWG CR sheet steel with two coat of corrosion resistant primer and painted with finish quality synthetic enamel paint. Junction box should have enough space for providing the following connectors and termination. (Make:KRONE/Equivalent)

OD3885/2025-2026:Supply, Installation, Testing and Commissioning of Wall Hanging Phone. (Make:BEETEL/Panasonic/Equivalent)

OD3889/2025-2026:Supply, Installation, Testing and Commissioning of Wifi Access Point Indoor Access Point is built with premium hardware and software quality and superior 802.11ac performance (up to 1 Gbps) 2 x 2 (Transmit x Receive) with 2 streams of data for 2.4 GHz and 5 GHz of reliable data delivery 802.11ac beamforming to improve range, minimizes interference while maximizing data rates Internal antennas for maximum RF performance. Wi-Fi 5 2x2 Access Point 1 GbE Port - Ceiling Mount, PoE Injector Included. OEM technical support/warranty along with required accessories. (Make:HP-ARUBA/ NETGEAR/Equivalent)

OD3893/2025-2026:Supply, Installation, Testing & Commissioning of Internet Management Solution – 100 concurrent users with hardware 3-year service package (includes onetime implementation cost plus 3- year online support & Training)

OD3910/2025-2026:Supply, Installation, Testing & Commissioning of 42" UHD 24X7 Android OS Monitor with 2 GB DDR4 Memory, 16 GB storage and Quad core CPU, WiFi 5 (802.11 a/b/g/n/ac) and Video inputs: xHDMI2.0, 1xDP1.2a, 1xUSB-A 3.0, 1xUSB-A 2.0, 1xUSB-A 2.0 (Internal), 1xUSB-C 3.0 and speakers with wall mount accesories. Make: Panasonic/ LG/ Sony

OD3911/2025-2026:Supply & Installation of Wireless Key Board and Mouse Bundle with non- rechargeable batteries.Make:- HP/Logitech/Equivalent

90.6.9.2:Supplying & Drawing unarmored PVC insulated and & PVC sheathed copper conductor Telephone Pair Cable conforming to ITD specification for indoor application through the existing conduit2 pair

OD3928/2025-2026:Supply, Installation, Testing and Commissioning of CAT5 RJ-11 Socket with single/Dual face plate and 3*3 metal/ pvc back box and rEquivalentuired accessories. (Make:MOLEX/ HONEYWELL/Equivalent)

OD3929/2025-2026:Sitc of 20Pair Krone Box with Krone Module

OD8379/2025-2026:Supply of EPABX system with 32 analog extension, 4 trunk, console port, PRI provision, Lightnening protector-4 nos expandable upto 48 ports

OD8378/2025-2026:Supply and installation of 24 Key operator console

OD8377/2025-2026:Supply of Analog with display, speaker console and CLI

OD21846/2025-2026:Supply, Installation, testing and commissioning of Single mode 1000Base-Lx To 1000Base-T PoE Media Converter with Singlemode SFP ports For Bi-Directional Transmission

OD21863/2025-2026:Supply, Installation, Testing and Commissioning of 19", 22'U 600x600 MM Depth Floor Mount Server Rack with Front Glass Door with lock and keys, Rear Perforated Doors with lock and keys, Side Openable Panels, Castors, Vertical PDU 6X16Amps - 2 No, Fan Housing Unit with 90cfm 4 Fans - 1 Set, Mounting Hardware Screws and all other accessories. (Make:NETRACK/VALRACK/Equivalent)

OD21864/2025-2026:Supply, Installation, Testing and Commissioning of 19", 15U 600x600 MM Depth Floor Mount Server Rack with Front Glass Door with lock and keys, Vertical PDU 6X 5pin16Amps - 2 No, Fan Housing Unit with 90cfm Fans - 2nos, Mounting Hardware Screws and all other accessories. (Make:NETRACK/VALRACK/Equivalent)

OD21865/2025-2026:Supply, Installation, Testing & Commissioning of HDMI Cable with Ethernet, 5 Mtr(16.4ft), 48 GBPS Transmission Ultra High Speed,4K, 3D,Male-to-Male,Compatible with all HDMI-Enabled Devices Make: Honeywell/Belkin/belden

OD21867/2025-2026:Supply and installation of DIN Rail Slotted Aluminum RoHS compliant 19" Inches Long 35mm Wide 7.5mm High with Hardware kit.

OD21869/2025-2026:Supply and installation of Waterproof 5x5 pole mount CCTV Camera PVC Junction box, IP66 with glands for cable entry

OD21886/2025-2026:Supply and installation of Pole Mount Camera clamp Bracket with 2 Nos. 100 MM SS Loops, for Outdoor use and compatible with 5X5 junction box.

OD21955/2025-2026:Supply, Installation, testing and commissioning of PoE System 10KV Ethernet Surge Protector, Industrial Din Rail Gigabit Lightning Arrestor, PoE++ 120Wmax RJ45 Surge Protector, 1000Mbps Zinc Alloy -40 deg celisius to 85deg celisius, GDT Gas Discharge Tube for camera and rack with all accessories to complete the work.

OD37232/2025-2026:Supply, installation, testing and commissioning of 108 cm (43 inches) 4K Ultra HD Smart LED Google TV with 4K Colour Engine, HDR 10, Dolby Digital, Home Theatre, Built-in Wifi support, BT Remote with Google Assistant, 2 Nos-HDMI 2.1, Operating system- Android TV, 16GB ROM (Internal Memory) with wall mount accesories, 5 year warranty. Make: Sony/Panasonic/Equivalent

OD37234/2025-2026:Supply, installation, testing and commissioning of 5MP IP IR Fixed Bullet Camera with with IR Distance Up To 30 meters, 3.6 mm lens, 1/2.7" Progressive CMOS sensor with Minimum Illumination: Colour 0.003 lux@ F1.6(AGC ON); B/W 0 lux@ IR ON, H.265+/H.265/H.264 Video Compression, IP67, IK10 Rated and metal body with Smart functions like Face Detection (FD), Human & Vehicle Detection (PD & VD), Perimeter Intrusion Detection (PID), ONVIF profile, 5 zone Backlight Compensation, True WDR and 3D DNR, and with flexible connectivity options, operation capability in extreme temperatures and a compact design for discreet outdoor installation. Also having CE, FCC, ROHS, BIS, ISO 9001, and Essential Requirement (ER) by STQC certification. Make: Panasonic/ Honeywell/Equivalent

OD37235/2025-2026:Supply, installation, testing and commissioning of 5MP IP IR Vandal Dome Camera with Minimum Illumination: Colour 0.003 lux@ F1.6(AGC ON); B/W 0 lux@ IR ON IR Distance Up To 30 meters, 2.8 mm lens, 1/2.7" Progressive CMOS sensor with H.265+/H.265/H.264 Video Compression, IP67, IK10 Rated and metal body with Smart functions like Face Detection (FD), Human & Vehicle Detection (PD & VD), Perimeter Intrusion Detection (PID), ONVIF profile, 5 zone Backlight Compensation, True WDR and 3D DNR, and having CE, FCC, ROHS, BIS, ISO 9001, and Essential Requirement (ER) by STQC certification. Make: Panasonic/ Honeywell/Equivalent

OD37236/2025-2026:Supply, installation, testing and commissioning of 5MP IP IR Motorized Varifocal Bullet Camera with 2.8mm to 12mm motorized lens with 1/2.7" Progressive CMOS sensor. Minimum Illumination: Colour 0.004 lux@ F1.6(AGC ON); B/W 0 lux@ IR ON and IR Distance Up To 50 meters, H.265+/H.265/H.264 Video Compression, IP67 Rated and a metal body, with Smart functions like Face Detection (FD), Human & Vehicle Detection (PD & VD), Perimeter Intrusion Detection (PID), ONVIF profile, 5 zone Backlight Compensation,True WDR and 3D DNR, and having CE, FCC, ROHS, BIS, ISO 9001, and Essential Requirement (ER) by STQC certification. Make: Panasonic/ Honeywell/Equivalent

OD37237/2025-2026:Supply, installation, testing and commissioning of 64 channel 8 SATA high-performance NVR with multiple interface options and remote access and monitoring support. This NVR should offer live view, storage, and playback support for cameras with resolutions up to 12MP. Incoming -640Mbps Outgoing -640Mbps, Compression: H+265,H.265,H.264, Multiple AI Support, HDD Support: 8HDD up to 18TB Each, Ethernet Port: 2 RJ45, Video Output Port: 4-HDMI, Alarm: 16in / 4 out, Audio: 1in / 1out, RAID0, RAID1, RAID5, RAID6, RAID10, NAS, FTP, and Cloud storage support. Make: Panasonic/ Honeywell/Equivalent

OD37819/2025-2026:Supply Installation, Testing & Commissioning of 32HP modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and heating, having all hermetically sealed inverter type Scroll Compressor(s), minimum two compressors for above 14 HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R 410 A Refrigerant, vibration isolators, with suitable foundation etc. complete as required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5 . (Make-Voltas, Samsung, LG, Mitsubishi Heavy or equivalent )

OD28657/2025-2026:Supply, Installation, Testing and Commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted high static ductable type Indoor unit equipped with washable synthetic media prefilter, fan section with low noise fan/dynamically balanced blower, multispeed motor, electronic expansion valve, corded remote control, outer cabinet, vibration Isolators, drain pan, drain pump, other necessary supports etc., suitable for operation on single phase AC supply 230 V ± 10%, 50 Hz complete as required. The system shall be capable to adjust air flow as per room requirement automatically. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make will be same as of Outdoor) : 8.5 TR hide away unit - high static with corded remote

OD28656/2025-2026:Supply, installation, testing and commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted ductable type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration isolators, drain pan, other necessary supports etc., suitable for operation on single phase AC supply 230 V ± 10%, 50 Hz complete as required. The unit shall have automatic force shut down provision in case of fire on receiveing signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make will be same as of Outdoor) : 5.5TR hide away unit - high static with corded remote

OD28731/2025-2026:Supply, installation, testing and commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted ductable type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration isolators, drain pan, other necessary supports etc., suitable for operation on single phase AC supply 230 V ± 10%, 50 Hz complete as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make will be same as of Outdoor) Mid static ductable units- 4.0 TR Hide Away Unit

OD28737/2025-2026:Supply, Installation, Testing and Commissioning of following minimum capacity and external static pressure VRF/VRV wall/ceiling mounted mid static ductable type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, electronic expansion valve, corded remote control, outer cabinet, vibration Isolators, drain pan, drain pump, other necessary supports etc., suitable for operation on single phase AC supply 230 V ± 10%, 50 Hz complete as required. The Indoor units must shut down upon receiving a singal from the BMS System/Fire Signals. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make will be same as of Outdoor) Mid static ductable units- 3.2 TR Hide Away Unit

OD28736/2025-2026:Supply, installation, testing and commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted ductable type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration isolators, drain pan, other necessary supports etc., suitable for operation on single phase AC supply 230 V ± 10%, 50 Hz complete as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make will be same as of Outdoor) Mid static ductable units- 2TR Hide Away Unit

OD28735/2025-2026:Supply, installation, testing and commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted ductable type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration isolators, drain pan, other necessary supports etc., suitable for operation on single phase AC supply 230 V ± 10%, 50 Hz complete as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make will be same as of Outdoor) Mid static ductable units- 1.6 TR Hide Away Unit

OD28734/2025-2026:Supply, installation, testing and commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted ductable type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration isolators, drain pan, other necessary supports etc., suitable for operation on single phase AC supply 230 V ± 10%, 50 Hz complete as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make will be same as of Outdoor) Mid static ductable units- 1.3 TR Hide Away Unit

OD28743/2025-2026:Supply, installation, testing and commissioning of following minimum capacity 2TR- VRV/VRF High wall type Indoor unit equipped with washable synthetic media pre- filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, outer cabinet, cord less remote control, drain pan, necessary accessories etc., suitable for operation on 230 V ± 10%, 50 Hz, single phase AC supply, complete as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make will be same as of Outdoor) - 2TR High Wall Unit

OD28742/2025-2026:Supply, Installation, Testing and Commissioning of following minimum capacity 1.6 TR High wall type Indoor unit equipped with and comfort washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, electronic expansion valve, outer cabinet, cord less remote control, drain pan, necessary accessories etc., suitable for operation on 230 V ± 10%, 50 Hz, single phase AC supply, complete as required. The system shall be capable to adjust air flow as per room requirement automatically. (Make will be same as of Outdoor) - 1.6 TR High Wall Unit

OD28741/2025-2026:Supply, Installation, Testing and Commissioning of 2.56 TR Air Cooled Floor standing Tower type split Air conditioners complete with Indoor unit(IDU), surface / concealed copper Refrigerant piping with insulation (closed cell elastomeric nitrile rubber tubular pipe section) upto 3 Mtr (IDU to ODU), copper power cable upto 3 Mtr (IDU to ODU), i/c drain pipe of suitable length and size. R-32/R-410/R-407C Green Refrigerant, wireless Remote control, suitable for working between 180-260V with low & high voltage cutoff and 50 hz ,1 phase AC supply complete as required. The system shall be capable to adjust air flow as per room requirement automatically. - 2.56 TR Floor Standing Concealed Unit

OD17540/2025-2026:Supply, filling and Pressure Testing of Refrigerant R410 A- Double Stage Vacuumizing and Gas Charging as per OEM standards . (Make - Freon/Du Pont or equivalent )

OD17636/2025-2026:Supply and installation of Acoustic Insulation using 10 mm thick open-cell nitrile rubber on the internal surface of the ducts, with adhesive as per the manufacturer's recommendations, and a density of 140-180 kg/m³.(Make - K-Flex/A-Flex)

OD28755/2025-2026:Supply and installation of Thermal Insulation using 13 mm thick nitrile rubber adhered to the external surface of the ducts with adhesive as per the manufacturers' recommendations, and a density of 45-55kg/m3.

OD29378/2025-2026:Supply and installation of factory made flexible canvas connections for each unit.

90.12.40.35:Supply & laying of one No. PVC insulated and PVC sheathed armoured copper power cable of 1.1 KV grade of the following sizes in the existing masonry open duct as required.4 core 25 sq mm

16.12.2.1:Supply, Installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular / round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports, etc as per approved drawings and specifications of following sheet thickness complete as required.Site fabricated GSS sheet metal rectangular ducting as per IS 655-2006 for 0.63 mm thick

16.15:Supplying & fixing of powder coated extruded aluminium Supply Air Grills with aluminium volume control dampers as per specifications.

OD37824/2025-2026:Providing high-tech steel wall supports for secure mounting, designed to sustain the static and dynamic weight of ductable IDUs. The rate is inclusive of all labor and materials

PP Electricals (BID ID -2453909)

Bidder Name

MOHAMMED MUSTHAFA K.

PP Electricals