PROVN OF BARBED WIRE WITH CONCERTINA COIL BEHIND THE ADMIN BLDG. AT NAD, UPGRADATION OF SQUAD INSTRUCTION ROOM FOR MARCOS NEAR BLDG. NO P-151 AT INS KARNA AND SPECIAL REPAIR TO BLDG. NO P-131 (AF BLOCK) IN PHASE-II RESIDENTIAL AREA UNDER GE(P) NAVY K

Amount

Taking down old tarfelt treatment from roof surfaces including plaster etc complete all as specified and as directed.

M&L for cutting crack to 'V' groove section of min 25mm Depth x 50mm wide in existing roof Parapet, Cleaning out and inserting APP membrane, grouting with cement and sand slurry of 1:3 complete all as specified and directed.

M & L rendering 10mm thick on roof padding in cement mortar 1:3 finished even and fair without using extra cement complete all as specified and as directed. Note: WPC will be measured and paid separately under relevant item as supply only

M&L for providing plain cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in roof padding & Haunching laid in slope as per requirement complete all as specified and as directed.

Supply only Integral Water Proofing Compound (ISI marked) of approved make.

M&L for normal water proofing treatment on roof slab portion consisting with the following operation : (i) Cleaning surface by wire brushes broom, removing dust and applying with bitumen primer conforming to IS 3384-1986 @ 0.20 kg per sqm (ii) laying of APP modified water proofing membrane weight not less than 4.00 Kg per Sqm reinforced with non woven polyester matt weighing not less than 160gm/Sqm having softening point not less than 150 degrees centigrade , having tensile strength of 650N/cm2 in longitudinal and transverse directions respectively of the reinforcement tearing strength of 180 N by torch on application including min 10cm side overlap and 15cm end laps. (iii) over the membrane finishing with solar reflective bituminous aluminium paint @ 0.10 Kg per Sqm

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles portions ordered to be dismantled complete all as specified and as directed by the Engineer-in-Charge.

M & L for Fly Ash block masonry (Modular size) solid blocks, exc. 10cm in width with class designation 75 (Kgf/cm2) and setting in CM 1:6 complete all as specified and as directed.

M & L for Fly Ash block masonry (Modular size) solid blocks, exc. 10cm in width with class designation 75 (Kgf/cm2) in half brick walls and setting in CM 1:4 complete all as specified and as directed.

Supply and lay TMT bar 8 mm dia for reinforcement of half brick wall complete all as specified and as directed. (Note : Reinforcement shall be provided at every fourth course of half brick wall).

M&L for repair to beam/ chajja/ drop/ facia (broken/ damaged), making good cement mortar 1:3, rendering 15 mm thick with using water proofing compound, sides and soffits in cement mortar 1:4 including necessary form work wherever damaged including re-inforcement duly welded if required, building height upto 10 mtr height with using proper scaffolding and staging.

Providing and applying acrylic cementitious , elastomeric , two component waterproof bonding agent, by mixing both the components to a lump free consistency by suitable means and applied on the prepared surface in 2 or 3 coats at an interval of 4 to 8 hours between coats , depending on the atmospheric conditions , applied at a total consumption of 3 Kg/Sqm to achieve a total dry fill thickness of 1.5 mm and coating shall be continued along the wall and allowed to cure etc. Coating shall offer the following performance properties. 1.Tensile strength-1 MPa as per ASTM D 412 2.Elongation -35 % as per ASTM D 412 3.Water penetration -No leakage at 5 bars as per DIN 1048

Taking down cement plaster of any description on brick walls including raking out joints, hacking for key, scrubbing down with water complete all as specified and as directed.

Material and labour for rendering 15mm thick in CM (1:6) on fair faces of brickwork or concrete surfaces, finished the surface even and smooth without using extra cement complete all as specified and as directed.

M&L for 15 mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar 1:4 in double layer, using WPC in outer layer of 5mm thick, complete all as specified and directed. Note : Water proofing compound will be measured and paid separately under relevant item as supply only

Material and labour for rendering 5mm thick in CM (1:4) on ceiling , finished the surface even and smooth without using extra cement complete all as specified and as directed.

Material and labour for preparation of new plastered surfaces of wall (internal walls) and applying two coats of oil bound distemper over a coat of alkali resistant primer over wall care putty of 1mm thick with roller complete all as specified and as directed.

M & L for Complete removal of existing treatment on internal plastered surfaces of wall including washing, rubbing down and stopping of old treatment by using vacuum based hand held or long handle sander machine, removing nails, removing concrete/ mortar spallings and any hanging items (weight less than 500 Grams), filling cracks/ holes wherever directed by grouting with a mixture of Putty and approved adhesive in 1:1 ratio and applying two coats of oil bound distemper over a coat of alkali resistant primer over wall care putty of 1 mm thick with roller machine complete all as specified and as directed.

M & L for preparation of new plastered surfaces of walls (external walls), applying two coats of Anti fungal based weather proof paint over a coat of alkali resistant primer over damp proof wall care putty of 1mm thick with roller complete all as specified and as directed.

M & L for Complete removal of existing treatment on external plastered surfaces of wall including washing, rubbing down and stopping of old treatment by using vacuum based hand held or long handle sander machine, Removing Nails, removing concrete/ Mortar spallings and any hanging items (weight less than 500 Grams), Filling cracks/ holes wherever directed by applying a mixture of Putty and approved adhesive in 1:1 ratio, applying two coats of Anti fungal based weather proof paint over a coat of alkali resistant primer over damp proof wall care putty of 1mm thick with roller complete all as specified and as directed.

M & L for preparation of old surfaces and applying One coat of white wash on Ceiling

M & L for preparation of New plastered surfaces and applying Three coats of white wash on Ceiling

Taking down Chowkhats or frames not exc. 1.5 sq. m each with shutters (without taking off shutters from the frames)

Taking down Chowkhats or frames exc. 1.5 sq. m but n exc 4.0 Sqm each with shutters (without taking off shutters from the frames)

S&F 2nd class hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and as directed.

S&F angle iron/ Flat iron work as in hold fasts including fixing with screws conforming to Fe-290 Gde-165 completed all as specified and as directed.

M&L for PCC (1:3:6) type C-1 using 20 mm graded crushed stone aggregates as in hold fast block complete.

S & F for 2nd class Hard wood , factory made, 35 mm thick plain framed, panelled shutters ( Two panels),with lock rail and panel of 9 mm BWP commercial ply or 12mm veneered particles board with commercial veneering on both faces. the size of rail and stile as per IS 2009 (part-I)

Supply and fix 30mm thick flush shutters solid core construction with particle board core and plywood face panels, one face covered with decorative face veneer with lipping / frame to match complete all as specified and as directed.

M & L for 35mm thick 2nd class HW Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (with sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a);

M & L for preparing new wooden surfaces of any description not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed .

S & F for Solid PVC Door Frame of size 50mm x47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing

S&F, factory made solid panel PVC door shutter 30mm thick (style)consisting of frame made out of MS tubes for top & bottom rail, MS frame shall be covered with heat moulded plain cover PVC "C" channel having a PVC sheet strip of 20mm width stuck in side with solvent cement for styles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and jointed to gether with solvent cement, supplying & fixing in the frame at site as per specification and shown on drawing in SSR Part II 2020.

Supply and fix 100 mm size butt hinges, medium weight, stainless steel and fixed complete all as specified and as directed.

S & F of 200mm Aluminium anodised, barrel tower bolts of extruded section and fixed

S & F Aluminium handles, cast type, anodised of size 150 mm

Supply and fix 200mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and as directed..

Supply and fix 150mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and as directed..

S & F in repairs for 18 mm thick Prelaminated MDF board, exterior grade prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with screws to timber frame work as in cupboards etc

S & F Continuous (piano) hinges, mild steel, bright finish or electro galvanised for 30 mm flaps

S & F for UPVC ,(unplastisized poly-Vinyl Chloride) sliding windows (3 track) frame multi-chambered and stiffened framed, using 88mm x 52mm size sections all-round as main frames fixed the window unit to the existing masonry wall/ Marble/ Granite with anchor fasteners without damaging as required. The frames shall be reinforced with GI profiles of thickness 1.25mm the entire window, The gaps between the window frames and masonry walls shall be filled with silicon or with any other suitable filler materials complete all as specified and as directed. Make : Rajshri Plastiwood/ Sintex/Duroplast Extrusion Pvt. Ltd

S&F UPVC Sliding window shutters, Three track, (2 No x Glazed & 1 No x wire mesh), White Colour of area not exceeding 2.0 Sq.m, made with extruded profile sections with wall thickness of 2.3mm±0.2mm of size 57mm x 42mm fixed to UPVC frame, shutters shall have well defined welded corner joints without any gaps, The shutters shall have necessary handles, arrangement to Drainage of water and other associated fittings to facilitate smooth operation. The shutters shall be reinforced with GI profiles of thickness 1.25mm including fixing glass and Wire mesh complete all as specified and as directed. Make : Rajshri Plastiwood/Sintex/Duroplast Extrusion Pvt. Ltd. (i) The unit rate quoted by the contractor includes cost of fixing of grills, glass panes and wire cloths including all other connected accessories. (ii) The Glass Panes and wire mesh shall be measured and paid separately under relevant Supply only Items of this Schedule. (iii) The size of UPVC sections specified in the description of item is minimum requirement, if the same size of section is not available, next higher size shall be provided by the contractor without any extra cost to the Department.

Providing and fixing factory made uPVC white / colour casement window frame for Ventilator (Size-60 mmx 58 mm ), made of extruded profiles. Profiles of frames will be mitered cut and fusion welded at all corners , 1.2+ 0.2.mm thick galvanized steel profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, all complete and as directed. Make : Rajshri Plastiwood/ Sintex/ Duroplast Extrusion Pvt. Ltd

Supply and fix rolled mild steel Fe-410-w (grade E-250) quality-A framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars and similar work, GI frames fixed to the window to existing masonry wall/ Marble/ Granite with anchor fasteners without damaging complete all as specified and as directed.

M & L for preparation of new steel Surfaces by removing durt,rust, oil or other contaminants from the surface of any description and applying two coats (approved shade/ Colour) of Powder coating of thickness not less than 60 microns ( Total thickness after 2 Coats is 120 Microns) complete all as specified and as directed. Notes :- 1.MS Grills or Angle posts are to be Powder coated in Workshops only. 2. Quoted rate includes Transportation. 3. Any defective item should be re- powder coated at bring to work site at contractor expenses. 4. Testing to Coating thickness to be carried out if required at contractor's own arrangements.

Supply only 5.00mm thick Sheet Glass ordinary quality in squares not exceeding 0.5 Sq.m in each pane complete all as specified and as directed.

All as per item No. 46 but frosted glass 4.00mm thick

Supply only stainless steel wire cloth of 0.36 mm nominal dia of wire and averaging of width of aperture 1.40mm, fixed with stainless steel wire staples complete all as specified and as directed.

Demolition of stone slabs of any description or thickness in floors, aprons etc

M & L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over a screed bed of 20mm thick in cement mortar 1:4

M&L for laying Green Marble 18 to 20 mm thick with polishing as in skirting/dado/ window cills/ jambs, cooking platform, vertical surface over cement rendering and jointed with grey cement, over and including screed bed of 15mm thick in CM 1:4, including pointing in white cement (1:2) using marble dust with admixture of pigment to match with the shade of marble and making nosing at right angle corner as specified and as directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified.

Demolition floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and as directed.

M & L for Ist or premium or standard quality of non skid, ceramic coloured joint free tiles of size area of each tile exceeding 0.18 sqm but not exceeding 0.38 and thickness 7-8mm, in floor, shelves etc, set and jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles over 15mm thick screed bed of CM 1:6 complete of item all as directed.

M & L for Ist or premium or standard quality of non skid, ceramic coloured joint free tiles of size area of each tile exceeding 0.18 sqm but not exceeding 0.38 and thickness 7-8mm, as in walls, shelves sides etc, set and jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles over 10mm thick rendering with CM 1:4 complete all as specified and as directed.

M & L for non skid, ceramic “coloured” joint free tiles of size area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm and thickness 7-8mm, in floor, shelves etc, set and jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles over 15mm thick screed bed of CM 1:6 complete all as specified and as directed.

M & L for glazed ceramic coloured tiles 300 x 450 x 7mm/ 250 x 450 x 7mm thick as in vertical surfaces (skirting) set & jointed in neat cement slurry & pointed with coloured cement to match over 10 mm thick rendering with CM 1:4 all as specified &directed.

S & F in repairs 25mm Gun metal Globe Gate valves with iron wheel head, screwed both ends for iron pipe

S & F in repairs PVC (SWR) pipes 110 mm dia single socketed in any length with rubber ring joints fixed to walls

S & F in repairs PVC (SWR) pipes 75 mm dia single socketed in any length with rubber ring joints fixed to walls

S & F PVC (SWR) vent cowl 110mm

S & F PVC (SWR) vent cowl 75mm

S & F PVC (SWR) bends with access door any radius 75mm.

S & F PVC (SWR) bends with access door any radius 110mm.

S & F in repairs Bib taps 15mm dia Fancy type Chromium Plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed

S & F in repairs two way bib cock, CP, Fancy type - 15mm dia complete all as specified and as directed.

S & F in repairs 15mm bore dia Concealed Stop valves, fancy type Chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed

S & F in repairs 15mm bore dia Concealed Stop valves with angular valve fancy type Chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed

Supply and fix in repair 15mm bore Pillar tap (Minimum weight 110gms) standard of PTMT any colour high pressure screwed for iron pipe complete all as specified and as directed.

S & F Health Faucet for 15mm dia with 1.5m long easy flex tube in Chrome finish and wall Hook of Stainless steel.

S & F in repairs Tubular towel rod brass chromium plated, 20mm dia, 60cm long between flanges

S&F, in repair Vitreous china Wash Hand Basin, white , flat back, size 550x400mm excluding taps ,waste, chain and plug but including brackets incl cutting and for pinning in ends of brackets.

S & F in repair Vitreous China, semi-pedestal pattern (Anglo-Indian Type), white (including fixing bolts and Seat Cover)

S&F in repair PVC Flushing cistern 10 ltr capacity with inlet ball valve float and handle and 32mm bore flush pipe including bracket complete all as specified and directed.

S & F Soap dish chromium plated, fixed to plugs with chromium plated brass screws

S & F in repairs Brass chromium plated shower rose 125mm size

S & F PVC flexible connections 15mm size with PTMT nuts of length 600mm

S & F 100 mm PVC (SWR) floor trap, plain including jointing with solvent cement

S & F 75 mm PVC (SWR) floor trap, plain including jointing with solvent cement

Provn of making hole in marble/granite slab of cooking platform for cooking gas pipe etc by means of drilling machine n.exc 25 mm dia all as directed by Engineer-in-Charge

M&L for hasp and staple Aluminium anodized ,incl bolt to hinge plate and fixed with screws 100 mm long.

Supply and fix in repairs Rotational moulded polyethylene water storage tanks (multi layer) 500 Ltrs capacity (Cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and as directed.

M&L for ball valve high pressure of PTMT with epoxy coated Alu Rod and high density plastic ball screwed for iron pipe and fixed 25 mm bore complete all as specified.

S&F in repair sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x160mm

Taking up or down 15mm bore, steel tubing and connection including cleaning for refixing or removal from site.

Taking up or down 20mm bore, steel tubing and connection including cleaning for refixing or removal from site.

S & F 32 mm outer dia, 3-layer PP-R P o l y p r o p y l e n e random copolymer) for concealed pipes SDR 7.4 (PN - 16) UV stabilised and a n t i m i c r o b i a l fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded p o l y p r o p y l e n e random fittings fixed complete to walls, ceilings or in floors etc.

S & F 25 mm outer dia, 3-layer PP-R Polypropylene random copolymer) for concealed pipes SDR 7.4 (PN - 16) UV stabilised and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc.

M & L for Treatment of soil under existing floors using emulsion @ one litre per hole , 300 MM apart including drilling and plugging 12 MM dia holes with cement mortar 1:2 to match the existing floors.

M & L ATT at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6 mm dia holes at a downward angle of 45 degree at 150 mm centre to centre and sealing the same .

M& L for ATT along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc in apron complete.

S&F 150 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors all as specified and directed.

M&L Concrete 1:3:6 Type C-2 bed to drain pipes including packing under & haunching against the sides of pipes after they are laid & tested in 150 mm dia pipe

Dismantling Wrought iron or Mild steel work of any description complete all as specified and as directed.

M&L stainless steel pipe conforming to grade SS-304 as in framed work such as railing, walkway etc.. and similar work including fixed in floors and wall with drilling and welding complete all as specified and as directed by the Engineer-in-Charge.

Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level)

M & L for Boulder Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc.15 cm thick, watered and rammed to a true surface

M & L for 75 mm thick Plain Cement concrete of type C2, 1:3:6 (40 mm graded aggregate) in Plinth protection/ sub base complete all as specified and as directed.

S & F stainless steel pipe 25mm dia Curtain rod for Windows, doors opening etc

S & F Fancy type Stainless steel Knobs for fixing curtain rod all as directed and specified

M&L for SS chromium plated plate rack of size 600x600mm made by 1 mm thick sheet all as approved by GE.

S & F of Black Granite stone Premium quality size exceeding 0.36 Sqm and up to 0.81 Sqm each stone on wall for foundation /Inauguration purpose at different location , with writing the letter in grooving by CNC machine in golden letters exceeding 100 Nos and up to 300 Nos, Incl stops , commas , short lines , dashes , arrows , hyphens , brackets etc. Stone to be fix over screed bed in CM 1:4 , Incl making good the surrounding wall of stone with required putty primer & weather coat painting , complete all as specified and directed.

S&F Pulley operated clothes drying system, Pull- it 7 feet long with 4 pipes Nos consisting of Stainless steel pipes each of outer dia 20mm and inner dia 18.00mm fixing on ceiling complete all as specified and directed by Engr- in-charge. Note:- (i) Pulley made up of delrin with rope guide mounted on channel pair of length 24"( distance between two pipes is adjustable). (ii) Locking system to hide rope knot. (iii) Channel to be mounted or fixed with self- tapping screws provided in kit. (iv) rope will be polyester braided, undyed of 4mm dia.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. N exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/ loose soil

All as per Srl item No. 105 here in before but for depth of foundation exe 1.5 mtr but n. exe 3.0 mtr from the starting point

M&L for plain cement concrete 1:4:8 type D2 (using 40 mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

M&L for Reinforced Cement Concrete 1:1.5:3 Type A1(Using 20mm graded granite stone aggregate) in footings, plinth beams and the like complete all as specified and directed.

M&L for Reinforced Cement Concrete1:1.5:3 Type A1(Using 20mm graded granite stone aggregate) in columns and pillars complete all as specified and directed.

M&L for Reinforced Cement Concrete 1:1.5:3 Type A1 (Using 20mm graded granite stone aggregate) in lintel beams, roof beams lintel beams and the like complete all as specified and directed.

M&L for Reinforced Cement Concrete 1:1.5:3 Type A1 (Using 20mm graded granite stone aggregate) in slabs supported on walls and the like complete all as specified and directed.

Use and waste of form work to sides of foundation/footings, plinth beams and similar work for rough finished surfaces complete all as specified and directed.

Use and waste of form work to sides of columns and pillars for fair finished surfaces complete all as specified and directed.

Use and waste of form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc.

Use and waste of form work to soffits of suspended slabs such as roof slabs, floors slabs, landings and similar work, not exceeding 200mm thick for fair finished surfaces complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm complete all as specified and directed.

Removing excavated soil exc. 250 m but n exc. 500 m and depositing where directed at a level n exc. 1.5 m above the starting point.

Filling under floor using surplus earth by spreading and levelling in layers not exc 25cms thick including watering and well ramming.

M & L for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius with built in CM 1:6

M&L for 10 mm thick rendering on Internal plaster of brick work or concrete surfaces in cement mortar 1:6 complete all as specified and directed

M & L for Plain Cement concrete 25mm thick type B-1, 1:2:4 (20mm graded aggregate) in sub base

M & L for non skid, ceramic “coloured” joint free tiles of size 400 x 400 x 6-7mm thick, in floor, shelves etc, set and jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles over 15mm thick screed bed of CM 1:6 complete of item all as directed.

M&L for 5 mm thick rendering on Celling plaster of concrete surfaces in cement mortar 1:3 complete all as specified and directed

M&L for preparation of new plastered wall surfaces and applying two coats of Cement base paint on external surfaces of walls etc complete all as specified and directed.

M&L Preparation of new plastered wall surfaces and applying two coats of plastic emulsion paint over priming paint including applying 3mm thick wall care putty .

S&F TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

All as per Srl item no. 126 here-in-before but for 5mm to 10mm dia as in stirrups, spacers and binders

S & F Solid PVC Door Frame of size 100mm x 60mm made out of 5mm WOOD GRAIN printed PVC sheet used instead of plain colour PVC sheet and edges will be painted to match with printed sheet, reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing

S & F of 150mm Aluminium anodised, barrel tower bolts of extruded section and fixed

S & F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

S&F brass chromium plated, Tubular towel rail , 20mm dia, D Type, 60 cm long between flanges.

S & F grating doom 125 mm dia with waste hole of PTMT (Min weight 40 gms)

S&F vitreous China wash down water closet pan (pedestal pattern), white including fixing bolts, low level flushing cistern 10 ltr capacity and flush pipe and seat cover etc. complete all as specified and as directed by the Engineer-in-Charge.

S & F PVC valve less, syphonic action type, flushing cistern of Capacity 10 Ltr low level, white, with inlet, ball valve, float and handle including brackets and flush pipe

S & F Vitreous China urinals, Half Stall type, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe)

S & F 15mm bore dia angle valves fancy type Chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed

S & F two way bib cock, CP, Fancy type - 15mm dia complete all as specified and as directed. Make : Jaquar Catalogue No : FON-40041 or equivalent as approved by GE

S & F Bib taps 15mm dia Fancy type Chromium Plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed

S&F Concealed stop cock, fancy type, chromium plated with long shank and cup, 15mm dia

S&F Shower rose 125mm with or without swivel joints , including fixing to steel pipes 15mm dia.

S & F 25mm Outer dia PP-R Ball valves (brass insert) as per requirement of the site

S & F 20mm Outer dia 3-layer pipes SDR 7.4 & SDR 11 UV stabilised and antimicrobial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc.

M & L for 75mm thick Cement concrete type C- 1, 1:3:6 (20mm graded aggregate) in Plinth Protection and finished even and smooth without using extra cement

S & F PVC (SWR) pipes 110 mm dia single socketed in any length with rubber ring joints laid in trenches or in floors.

S & F PVC (SWR) pipes 40 mm dia fixed to walls

S & F PVC (SWR) pipes 75 mm dia single socketed in any length with rubber ring joints laid in trenches or in floors.

S&F 110mm dia PVC (SWR) bends any radius

S&F 75 mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement

S&F PVC (SWR) gully trap 110 mm, setting and jointing with solvent cement including grating

S&F Powder coated Anodised aluminium frame for ventilators, with one or more rebates, including jointing cleat for fixing etc complete all as specified

S&F Sheet glass 4mm thick, pinheaded in louvers complete all as specified and as directed.

M & L for providing Precast RCC 1:2:4, Type B-1 using 20mm graded stone aggregate as in Shelves ,landings, cover slabs [for manholes etc], chullah hoods, chajjas, water troughs, mangers, and similar articles with plain faces set in cement mortar 1:6 complete all as specified and as directed.

S&F wash hand basin of size 550x400 vitreous China (flat back or angle back type) including half pedestal and cutting for and pinning in ends of brackets or erecting stand including supply and fixing of waste coupling, waste pipe etc. complete all as specified and as directed by the Engineer-in-Charge.

S&F 50mm dia. PVC waste pipes for WHB/sink fixed to walls including fittings and connecting to multiple floor trap complete all as specified and as directed by the Engineer-in-Charge.

S & F 500 litres Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified and directed

S & F Anodised aluminium snap grid frame work for false ceiling of size 605 x 605mm all as specified

M&L 4mm thick non-asbestos fibre cement plain building boards fixed to timber/GI/aluminium framework with screws in false ceiling complete all as specified and directed by the Engineer-in-Charge.

S & F for hangers 6 mm dia G.I Upto (1200 mm length) adjusting level fixed to RCC roof by means of ceiling cleats made out of G.I Flat 40 x 3 mm size 600 mm long and expansion hold fasteners 12.5 mm dia . 40mm long complete all as specified

S&F Venetian blinds (Designer pattern) of washable fabric material, with aluminium channels, operating arrangements etc complete all as specified and as directed.

Surface excavation n.exc.30cm deep and avg 15cm deep and getting out in soft/ loose soil

Removing excavated soil to a distance n.exc. 50m and depositing where directed at a level n.exc.1.5m above the starting point

M&L for PCC 1:2:4 type B2 (using 40 mm graded stone aggregate) as in foundation filling and mass concrete.

M&L for Precast Stone Block masonary using PCC 1:3:6 type C1 (using 20mm graded stone aggregate) exc. 10cm in width and set in CM 1:6

M&L for Precast RCC 1:1.5:3 type A1 (using 20 mm graded stone aggregate) set in CM 1:4 as in Lintels, cover slabs etc.

M&L for PCC 1:2:4 type B2 (using 40mm graded stone aggregate) as in wall.

M&L for 12 mm thick plastering in CM 1: 4 and finishing the surface even and smooth without using extra cement.

M&L TMT bars 6 to 8mm dia cut to length, bent to shape required including cracking bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia complete all as specified and as directed.

M&L for PCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in benching and coping.

Dismantling of Stone/ Brick masonry, built in cement mortar including all quoins, arches, pillars, etc portions ordered to be dismantled carefully without damaging main structure complete all as specified and as directed. Note :- If any Main structure damaged during the Dismantling, the same will be make good by the contractor without any extra cost to Department.

Demolition of Cement Concrete of any description and in any position, as in Compound walls (Straight or curved) for fixing of iron grills / Gratings/ Posts, portions ordered to be dismantled carefully without damaging main structure complete all as specified and as directed. Note :- If any Main structure damaged during the Dismantling, the same will be make good by the contractor without any extra cost to Department.

M & L for Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in CM 1:4 but except stone complete all as specified and as and as directed. Note : Old stone obtained from Item No 169 here in before shall be reused

M&L for Raised pointing to random or polygonal rubble, uncoursed or brought upto courses built in CM 1:4 complete all as specified and as directed.

M&L for Plain Cement Concrete 1:2:4 type B1 (Using 20mm stone aggregate as in Coping and fixing iron angle post/ grill including weathering, slightly rounded or chamfered angles and including necessary form work complete all as specified and as directed.

S&F 610mm dia. concertina coil, galvanised, precoated with black anti-corrosive paint, weighing approx. 8 Kg per coil of 6-8m stretch and fixing to any type of standard rails, straining bolts etc. including securing or tying at crossings with necessary clips/pins etc complete all as specified and as directed by the Engineer-in-Charge.

S&F galvanised. 2 strand, steel barbed wire 2.24 mm dia. barbed with 2mm dia. barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. complete all as specified and as directed by the Engineer-in-Charge. Note: Each line wire will be measured.

S&F mild steel work in Supporting Angle posts, including embedding in concrete and screwing etc. in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; angle and flat iron fillets (for Concertina coil) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed.

Supply and fix Framed work such as grills, gratings, etc.. with ends of bars shouldered and / or riveted, or forged into spikes ; framed guard bars and similar work conforming to Fe-290, Gde-E-165 as ornamental and intricate design complete all as specified and as directed.

M & L for Preparation of New plastered surfaces of wall and applying Two coat of Cement base paint over a coat of alkali resistant primer including matching the surface / colour with existing treatment complete all as specified and as directed.

Taking down carefully existing aluminium /copper conductor point wiring (light / fan / socket or power point) complete, with all fittings such as switches, socket, regulator, ceiling rose, utility light fittings and lamp holders etc and removing materials from site and making good the disturbed surfaces of walls roof and floor etc as per existing specification complete all as specified and as directed.

Taking down carefully by unscrewing from boards / outlet boxes, fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, brackets, ceiling fittings, bulk head fittings, tube light fittings and fan regulators etc. for reuse at site complete all as specified and as directed. (Note : To be measured only when found serviceable in all respects complete for reuse)

M&L for point wiring for one light point controlled by 1 one way switch with 1.5 Sqmm (nominal cross-sectional area) FRLS PVC insulated and unsheathed 1100 V grade multi stranded copper conductor single core cable drawn through and including new PVC casing capping with all fittings and accessories including one run of FRLS PVC insulated and unsheathed single core multi stranded copper conductor cable of size 1.5 Sqmm as earth continuity conductor to common earth and earth dolly including new pressed steel sunken boxes readily available (having thickness not less than 1.22 mm for boxes upto a size of 200 mm x 300 mm and beyond that the wall thickness shall not be less than 1.63 mm) concealed type with 3 mm thick bakelite sheet cover for mounting switches, sockets, fan regulator etc including testing complete all as specified and as directed.

All as per Item no 181 here-in-before but for one light point controlled by two 2 way switch all as specified and as directed.

All as per Item no 181 here-in-before but for one fan /E Fan point controlled by 1 one way switch and regulator all as specified and as directed.

All as per Item no 181 above but for one 3 pin switch socket outlet, 5 Amp on independent board all as specified and as directed.

All as per Item no 181 here-in-before but for one switch socket outlet, 5 Amp on same board with other switches all as specified and as directed

All as per Item no 181 here-in-before but for one16 Amp 3 & 5 pin switch socket outlet, independent with 4.0 Sqmm single core multi-stranded copper conductor cable (FRLS) along with 4.0 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire all as specified and as directed.

All as per Item no 181 here-in-before but for one bell point controlled by one bell push on the same board with other switches or independent all as specified and as directed.

Material and labour for sub main wiring with two single core PVC insulated un-sheathed cable with multi-stranded copper conductor of 6.0 sq mm size and drawing into and including concealed PVC conduit of 25 mm dia with earthing cable of PVC insulated un-sheathed stranded copper conductor of size 6.0 sqmm, single core, as earth continuity wire all as specified and as directed. (NOTE: 3 runs of 6.0 Sqmm cable and one run of PVC concealed conduit 25mm dia will be measured as one unit i.e. RM)

Supply and fixing socket out let combination 2 in 1 3 pin 5 and 15 amp flush type universal all as specified and as directed.

Supply and fixing switch piano flush button single pole one way 5 amps all as specified and as directed.

Fixing only switch flush button single pole one way 5 amp all as specified and as directed. (Material obtained from item No 180 here in before shall be used)

S&F switch flush type, single pole Two way 5 Amps 230 volts all as specified and as directed.

Supply and fixing switch socket outlet 2 in 1 3 pin 5 amp flush type with incl switch all as specified and as directed.

Fixing only switch socket outlet 5 amp flush type all as specified and as directed. (Material obtained from item No 180 here in before shall be used)

Supply and fixing ceiling rose surface bakelite three terminals all as specified and as directed.

Fixing only ceiling rose surface bakelite three terminals all as specified and as directed. (Material obtained from item No 180 here in before shall be used)

Supply and fixing fan regulator electronic deluxe rotary step type all as specified and as directed.

Fixing only fan regulator any type all as specified and as directed. (Material obtained from item No 180 here in before shall be used)

S&F bell ding dong 5 Amps, flush type, 230 Volts, 50 Hz complete all as specified and as directed by the Engineer-in-Charge.

S&F bell push flush type 5 Amps, 230 Volts, 50 Hz complete all as specified and as directed by the Engineer-in-Charge.

S&F sheet metal enclosure for MCB DBs, phosphatised, Powder coated , triple pole and neutral (TPN) 240 Volt , double door, suitable for 4 way with din rail earth and neutral bar all as specified and as directed.

S&F sheet metal enclosure for MCB DBs, phosphatised, Powder coated , single pole and neutral (SPN) 240 Volt , double door, suitable for 8 way with din rail earth and neutral bar all as specified and as directed.

S&F MCB, FP, rupturing capacity 10 kA, ‘C’ curve, 63 Amp, 415 volts ISI marked complete all as specified and as directed.

Supply and fixing MCB Single Pole (SP) C curve 10kA breaking capacity of 6 to 32 amps, 240 Volts in proper position all as specified and as directed.

S&F MCB, DP, rupturing capacity 10 kA, ‘C’ curve, 40 Amp, ISI marked complete all as specified and as directed.

Supply and fixing indoor luminaries decorative batten for wall/ceiling mounting box type energy efficient saving LED BATTEN LIGHT 10 W,230 V,50 HZ, slim integrated design easy install incl twin twisted copper conductor flexible wire from ceiling rose to connector all as specified and as directed.

Supply and fixing indoor luminaries decorative batten for wall/ceiling mounting box type Extruded aluminium housing ,PC Diffuser, energy efficient saving LED BATTEN LIGHT 20W,230 V,50 HZ, slim integrated design easy install incl twin twisted copper conductor flexible wire from ceiling rose to connector all as specified and as directed.

S&F 10 W LED decorative CITY 3 wall/surface mounting polycarbonate body suitable for retrofit LED Lamp Base B-22 incl lamp ,all as specified and as directed.

S&F LED mirror light fittings 07 W, 230 V, 50 HZ suitable for indoor and outdoor applications complete all as specified and as directed.

Supply and fixing LED bulk head fittings 10 W,230 V,50 HZ suitable for indoor and outdoor applications complete all as specified and as directed.

Supply and fixing on wall security LED light luminaries fitting 1X25 W and including cable for connection from ceiling rose with 1.5 Sqmm PVC insulated stranded copper conductor (FRLS) cable including 25 mm GI bracket medium grade 1.5 m long bent to shape including bolt, nut,washer,clamp etc all as specified and as directed by the Engineer-in-charge.

Taking down carefully ceiling fan any sweep and any make after disconnecting the electrical connection, dismantling the blades and removing fan incl blades for safe custody for reuse and re-assembling the fan complete and refixing the fan in same position including all electrical connection all as specified and as directed.

Material and labour for taking out and removing burnt copper winding, cleaning the armature, rewinding the fan armature for 1200mm sweep fan with new super enamelled copper wire of existing gauge including supply and fixing necessary insulating materials etc and varnishing with approved grade of insulation varnish and heating up and testing all as specified and as directed.

Supply only ball bearings, bearing No.6201/6202 suitable for ceiling fan/exhaust fan of any sweep any make/model complete all as specified and as directed by the Engineer-in-Charge.

Supply only fan condenser up to 2.5 mfd suitable for ceiling fan complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for painting of ceiling fans complete of any sweep/make with one coat of first quality synthetic enamel paint of approved tint by spray including preparation of old painted surface and removing all dust, oil mark etc and filling cavities with filler materials, and writing serial / MES number as specified (with paint of black colour with each letters/figures in Block of height n.exc 2 cm ) complete all as specified and as directed.

Supply and fixing Ceiling fan of 1200 mm sweep 5 STAR rating with clamp and hook at proper position with taking down old ceiling fan and kept in MES store yard with necessary accessories etc. all as specified and as directed. (Havells model no : ES 40 or equivalent as approved by GE)

M&L for exhaust fan metal body of size 300 mm sweep, single phase,230 volts AC with louver shutter /grill and connection complete with cutting of a hole on wall of suitable size all as specified and as directed.

M&L for exhaust fan PVC body of size 250 mm sweep, single phase, 230volts AC with louver shutter /grill and connection complete with cutting of a hole on wall of suitable size all as specified and as directed.

Material and labour for sand cushioning for protection of underground cable consolidated and compacted with clean dry sand all as specified and as directed (Note : Compacted thickness shall only be measured and paid)

Material and labour for XLPE insulated GI wire/strip armoured electric power cable (Heavy duty) ISI marked with stranded aluminium conductor 1100 volts grade, cross sectional area 25 Sqmm 3.5 core laid in trench /poles/on wall complete all as specified and as directed.

Supply and lay bricks common burnt clay building bricks sub-class B of size 230x113x75 in cable trenches complete all as directed

Drilling of hole horizontally 80/40 mm dia below the road for providing casing pipe of cable protection by using mechanical /hand drill all as specified and as directed.

S&F single pole and neutral enclosure with two pin earth plug with 01 Nos of MCB SP 20 Amps 'C' series complete all as specified and as directed.

M&L for galvanized iron tubing 50 mm bore light grade with all fittings for protection of FRLS cable, laid in trenches/wall/floor including necessary clamps, bolt/nut complete all as specified and as directed. Note: Earth work excavation will be measured and paid separately.

Earthing complete with 3.0 m CI pipe 80 mm dia with flanged ends, centrifugally cast, class A, in any length, joints with suitable stainless steel nuts and bolts and sufficient slot up to 2.5 mtrs length buried directly and preferably vertically in ground with top flanged ended 2.5 mtrs below ground level welded/ connected with GI strip 32×6mm size on the top edge of the flange to bottom edge of the flanged for earthing including filling the pit with charcoal common salt surrounding the earth pipe including drilling 400 mm dia bore in any strata of soil to lower the CI pipe complete including necessary excavation and earth work PCC (1:3:6) type C-1 with 50 mm thick pre cast RCC (1:2:4) type B-1 cover slab and necessary testing on completion. .

Material and labour for sub main wiring with two single core PVC insulated un-sheathed cable with multi-stranded copper conductor of 4.0 sq mm size and drawing into and including concealed PVC conduit of 25 mm dia with earthing cable of PVC insulated un-sheathed stranded copper conductor of size 4.0 sqmm, single core, as earth continuity wire all as specified and as directed. (NOTE: 3 runs of 4.0 Sqmm cable and one run of PVC concealed conduit 25mm dia will be measured as one unit i.e. RM)

S&F sheet metal enclosure for MCB DBs, phosphatised, Powder coated , single pole and neutral (SPN) 240 Volt , double door, suitable for 4 way with din rail earth and neutral bar all as specified and as directed.

Supply and fixing mounting luminaries LED downlighter pendant lamp of 36 watt slim integrated design easy install including twin twisted copper conductor flexible wire from ceiling rose to connector complete all as specified and as directed.

Material and labour for XLPE insulated GI wire/strip armoured electric power cable (Heavy duty) ISI marked with stranded aluminium conductor 1100 volts grade, cross sectional area 16 Sqmm 4 core laid in trench /poles/on wall complete all as specified and as directed.

M&L for earthing complete with galvanized steel earth plate electrode 600x 600 x 6.3 mm buried directly in ground (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.5m below ground level, connected to galvanized earth lead wire 4mm dia (upto 7.5 m in length from earth plate) by means of galvanized iron or steel bolts, nuts, check nuts and washers, and connected to equipments as directed, including funnel with GI med grade watering pipe 20mm bore, wire mesh charcoal or coke and common salt in alternate layers, of 15cm compacted thickness all around the earth electrode, with concrete pit in PCC 1:3:6 type C-1, 50mm thick pre cast RCC 1:2:4 type B1 cover slab reinforced with 8mm dia reinforced bar 15cm C/C and earth lead handle protection including necessary excavation earth work in soft/loose soil and disposal of spoil to a distance n.exc. 50m and necessary testing complete all as shown on electrical plate No. 3 of MES SSR Part-I and as directed

P SRINIVASA RAO

SSV CONSTRUCTIONS

SRI VENKATA SAI MANIKANTA CONSTRUCTIONS