S. R. to Store Building inside Navsari District Jail, Dist. Navsari. (Incl. Elect. ) (S. R. Jail Priority - 2025-26) (Eighth Attempt)

No. In Figure In Words

1 Removing and scraping of old deteriorated plaster of any 130.00 Sqmt. 19.86 Rupees Nineteen And Paise Eighty

thickness fromm wall / R.C.C member including stacking of Six Only

serviceable material and disposal of unserviceable from site

of work with all lead and lift

2 Provinding 20 mm thick SAND FACED cement PLASTER on 100.00 Sqmt. 335.79 Rupees Three Hundred Thirty Five

walls above ground level consisting 12 mm thick backing And Paise Seventy Nine Only

coat of C.M. 1: 3 ( 1 cement : 3 sand ) and 8mm thick

finishing coat of C.M. 1:1 ( 1 cement : 1 sand ) etc. Complete

for any height. 20mm Double Coat Sand Face Plaster (

gutaka only) For Up to (G+3)

3 Pointing on Brick masonry with cement mortar 1:3 (1-cement 20.00 Sqmt. 96.54 Rupees Ninety Six And Paise Fifty

: 3-coarse sand) (A) Flush pointing Four Only

4 Cutting out cracks roof terrace to V-Section cleaning out and 50.00 Rmt 77.34 Rupees Seventy Seven And Paise

filling solidly with a hot mixture of bitumen and clean dry sand Thirty Four Only

(1:1 by weight)

5 Provinding 15 mm thick cement PLASTER in single coat on 31.00 Sqmt. 223.27 Rupees Two Hundred Twenty Three

brick or concrete wall for interior plastering and finished even And Paise Twenty Seven Only

and smooth in C.M. 1:4 ( 1 cement : 4 sand ) including

finishing with floating coat of neat cement slurry at ALL Floor

Item Estimated Rate (in Rupees)

Description Of Item Qty. Unit Amount (Rs.)

No. In Figure In Words

6 Removing dry or oil bound distemper by a washing and 1470.00 Sqmt. 11.47 Rupees Eleven And Paise Forty

scraping and sand papering the wall surface smooth Seven Only

including necessary repairs to scratches complete.

7 Finishing Wall surface with plastic emulsion paint on Wall 899.00 Sqmt. 178.14 Rupees One Hundred Seventy Eight

surface (two coats) to give an required shap even shade after And Paise Fourteen Only

throughly brushing the surface to remove all dirt and remains

of loose poweder material etc. complete. Rate are inclusive

of applying two coats of lapy (putty) and one coat of primer

on new Wall surface to give and even shade including

throughly brushing the surface free from mortar dropping and

other foreign matter and sand papered smooth. fine putty

shall be approved brand by GSPHCL only & Primer shall be

approved brand by GSPHCL only and plastic Emulsion Paint

Shall be Approved brand by GSPHCL only paint only.

8 Finishing walls with Weather Proof Exterior Emulsion Paint 340.00 Sqmt. 150.52 Rupees One Hundred Fifty And Paise

on Wall Surfaces (Two Coats) over and above Applying one Fifty Two Only

coat of Primer to give an Required shape and even shade

after thoroughly brushing the surface to remove all dirt, and

remains of loose powdered materials and finishing smooth

etc. complete. (Primer Shall be of Weather Coat Exterior

Primer of Berger Paint India Ltd or Asian Paint Trucare

Exterior Primer of Asian Paint or Exterior Sealer E 900 of

Dulux Paint Only and Exterior Emulsion Paint shall be

Weather Coat Smooth of Berger Paint India Ltd. or Apex

Weather Proof Emulsion of Asian Paint or Dulux Weather

Shield Projects of Dulux Paint Only.)

9 Providing and laying polished Kota stone slab flooring over 144.00 Sqmt 1000.91 Rupees One Thousand And Paise

20mm (Average) thick base of cement mortar 1:6 (1-cement Ninety One Only

: 6-coarse sand) or L.M. 1.1.5 (1-Lime putty :1.5 - coarse

sand) laid over and jointed with grey cement slurry mixed

with pigment to match the shade of

slab including rubbing and polishing etc. complete. (A) 25mm

Item Estimated Rate (in Rupees)

Description Of Item Qty. Unit Amount (Rs.)

No. In Figure In Words

10 Painting two coats (excluding priming coat) on perviously 359.00 Sqmt 76.85 Rupees Seventy Six And Paise

painted steel and other metal surfaces with Synthetic Eighty Five Only

Enamal paint.

11 Painting two coats (excluding priming coat) on perviously 53.00 Sqmt 83.95 Rupees Eighty Three And Paise

painted Wood and woode based surfaces with enamal paint. Ninety Five Only

12 Provinding and fixing chicken wire mesh Jali 0.18 mm and 20.00 Sqmt 64.06 Rupees Sixty Four And Paise Six

0.18m wide with necessary screws and nails to joint between Only

R.C.C. column and brick work etc. complete as per Engineer-

in-charge.

13 Providing , Fabricating and fixing M.S. GRILL/GATE of 322.00 Kg 74.99 Rupees Seventy Four And Paise

approved pattern fabricated from M.S. flat,square bars, round Ninety Nine Only

bars,c-channel, box pipe as per detail Drawings. Rate is

inclusive of welding with grinding smooth surface, two coats

of Oil paint and one coat of yellow Zinc primer coat of

approved brand only. Oil paint shall be Luxol Enamel paint of

Berger Paint india limited. or asian paint apcolite premium

gloss Enamel of asian paint or Dulux premium gloss enamel

of dulux paint only.

14 Providing & fixing 3mm acrylic sheet of size 60 x 15 cm with 5.00 Nos. 100.00 Rupees One Hundred Only

necessary screws ,plugs etc for any Number, Writing

Letter/Matter in 10cm size of radium adhesive patty or

directed by engineer in charge.

15 providing and corrogulated JSW pre coated sheet roofing 269.00 Sqmt. 984.37 Rupees Nine Hundred Eighty Four

fixed withh galvanised iron J or L hooks, bolts and Nuts 8 And Paise Thirty Seven Only

mm dia with bitumin and G.I. Limpet washer or G.I. limpet

washer with white lead complete excluding the cost of

Purlines , rafters and trusses(0.60mm thick)

Item Estimated Rate (in Rupees)

Description Of Item Qty. Unit Amount (Rs.)

No. In Figure In Words

16 Providing and fixing rolling shutters of approved make made 16.00 Sqmt. 4501.00 Rupees Four Thousand Five

of 80mm wide M.S. laths inter-locked together through their Hundred One Only

entire length and jointed together at the ends by end locks

mounted on specially designed pipe arragements for inside

and outside locking with spring etc. complete. (B) Shutters

having width 3.5M and above

(Electrical Item)

17A Providing & Erecting Point wiring with 1.1 KV grade ISI 47.00 Point 372.00 Rupees Three Hundred Seventy Two

marked 2 X 1.5 sq. mm copper PVC insulted FRLS wire with Only

1.5 sq. mm (green) copper PVC insulated FRLS wire for

earth continuity in FIA approved ISI mark medium class white

colour 20/25 mm dia. embossed rigid PVC pipe with PVC

fitting fixed with adhesive solution erected on Brick Wall

along th continuous G.I. fish wire to draw wires and finishing

the surface to match the wall / ceiling complete with

approved make 5/6 Amp. ISI make modular type switch and

accessories mounted in 20 G. G.I. company fabricated

metallic box covered with appropriate front plate modules

erected flushed with wall / ceiling with necessary modular

lamp holder / modular ceiling rose / HD Connector as

directed for Open wiring Light point. Cat.-II..Length of point

wiring must not increase than 10 mtr. For that necessary

switch boards and their locations must be finalised before

execution by agency otherwise payment will not be done for

extra long point. (For future extention, if required, agency has

to erect one higher size metal box and modular plate as per

instruction of EIC. Cost of blank plate shall be paid as per

tender item) [Wire must be having box packing (e) in existing

pipe erected flushed on wall/ceiling complete cat.III

17B For Fan Point.(with 6A Modular type switch and Two Module 10.00 Point 517.00 Rupees Five Hundred Seventeen

hum free 5/6 step EME step type Electronic fan regulator Only

both having ISI Make ) Cat-III

Item Estimated Rate (in Rupees)

Description Of Item Qty. Unit Amount (Rs.)

No. In Figure In Words

17C For separate Point (with 6 Amp. Switch & 5 pin socket both 15.00 Point 385.00 Rupees Three Hundred Eighty Five

having ISI Make) Cat-III Only

17D For Looped on switch board (with 6 Amp. Switch & 3/5 pin 15.00 Point 255.00 Rupees Two Hundred Fifty Five Only

socket) (Cat-III)

18A Providing and erecting Medium Class FIA approved and ISI 204.00 Mtr. 24.00 Rupees Twenty Four Only

mark white colour (embossed) RIGID PVC PIPES of

following size complete erected with necessary PVC fittings &

Junction boxes fixed with adhesive solution. concealed in

wall / slab along with continuous fish wire to draw mains, laid

in approved manner. Zari for PVC Pipe & Boxes shall be

plastering by cement mortar & finishing the surface to match

the wall / ceiling. (a) 20 mm dia.

18B 25 mm dia. 50.00 Mtr. 33.00 Rupees Thirty Three Only

19A Providing & Erecting Mains with FRLS PVC Insulated wire 188.00 Mtr. 46.00 Rupees Forty Six Only

ISI marked 1.1 KV grade with FIA approved ISI mark

medium class 20/25/32 mm dia. embossed rigid PVC pipe

with PVC fitting fixed with adhesive solution to be erected

on/in brick wall / slab along with continuous G. I. fish wire to

draw mains laid in approved manner with plastering by

cement mortar & finishing the surface to match the wall /

ceiling complete with FRLS PVC insulated wire for earth

continuity. (Approved ISI make only) (Conductor resistance

should be as per IS:8130/1984) (E) in existing pipe and

accessories [a] 2 x 1.5 sq.mm. FRLS copper multi stranded

conductor mains with 1.5 sq.mm. FRLS copper multi

stranded conductor for earthing as per standard colour code.

(for point wiring and Lighting SB mains) [Wire must be having

box packing.

Item Estimated Rate (in Rupees)

Description Of Item Qty. Unit Amount (Rs.)

No. In Figure In Words

19B For 2 x 2.5 sq.mm. FRLS copper multi stranded conductor 50.00 Mtr. 62.00 Rupees Sixty Two Only

mains with 1.5 sq.mm. FRLS copper multi stranded

conductor for earthing as per standard colour code. (E) in

existing pipe and accessories (for MCBDB mains) [Wire must

be having box packing] (Conductor resistance should be as

per IS:8130/1984

19C For 2 x 6.0 sq.mm. FRLS copper multi stranded conductor 80.00 Mtr. 120.00 Rupees One Hundred Twenty Only

mains with 2.5 sq.mm. FRLS copper multi stranded

conductor for earthing as per standard colour code. (E) in

existing pipe and accessories (for MCBDB mains) [Wire must

be having box packing] (Conductor resistance should be as

per IS:8130/1984

20 Providing & erecting PVC Corrugated Flexible Conduit with 25.00 Mtr. 21.00 Rupees Twenty One Only

required nos. of coupling, PVC bushes, Check-nuts etc.

complete of following sizes.

21 Providing & Erecting Plug Point wiring with 1.1 KV grade ISI 5.00 Point 526.00 Rupees Five Hundred Twenty Six

marked approved make 2 x 2.5 sq.mm copper PVC insulated Only

FRLS wire with 1.5 sq.mm (green) copper PVC insulated

FRLS wire for earth continuity in FIA approved ISI mark (e)

in existing pipe erected flushed on wall/ceiling complete and

accessories erected flushed on wall/ceiling complete with

white colour 20/25 mm dia. embossed rigid PVC pipe with

PVC fitting fixed with adhesive solution erected flushed on

wall/ceiling complete the surface to match the wall / ceiling

complete with approved make 5/6 Amp. ISI make modular

type switch and accessories mounted in 20 G. G.I. company

fabricated metallic box covered with appropriate front plate

modules erected flushed with wall / ceiling with necessary

modular lamp holder / modular ceiling rose / HD Connector

as directed for Open wiring.. (a) 16 Amp indicator switch &

No. 6/16 A universal socket white colour suitable for 3 pin top

duly both having ISI mark. (Necessary Sheet Must Be

Erected On All Box To Prevent Mortor Going In To The Box)

(Conductor resistance should be as per IS:8130/1984

Item Estimated Rate (in Rupees)

Description Of Item Qty. Unit Amount (Rs.)

No. In Figure In Words

22 Providing following type of Modular Type Accessories 21.00 Each 25.00 Rupees Twenty Five Only

mounted with PVC / metallic/Wooden box, single mounting

base frame covered with textured / metallic/white front plate

modules erected with necessary connections as per site

situation directed by Engineer In charge. (7) Blank Plate

Single Cat.-III

23 Supplying and Erecting LED indoor fitting of 35.00 Nos. 370.00 Rupees Three Hundred Seventy Only

approximately 4feet long with LED of wattage 0.2W to

0.5W assemble on single MCPCB with housing use as

a heat sink shall be made from Aluminum extrusion

having enough strength (sample must be approved by

EIC) with polycarbonate diffuser with following specification:

(A) Company mark/name on the fitting. (B) Rated input

voltage and frequency: 220V to 240 VAC ; 50Hz.

(C) Rated input wattage: max. 24w (D) Rated input current :

0.2 Amp (E) Power Factor : Min. 0.90 (F) ATHD : Max. 15%

(G) Rated Luminous flux: Min. 2420 lm (H) CCT: 6500K

(I) CRI: Min. 80Ra (J) Driver Efficiency: Min. 80% (K) LED

life span: Min. 50000 Hrs @ L70 (L) Over Voltage protection:

Withstand up to 440V/AC for 4 Hrs. (M)Surge protection :

Min. 2KV (N) IP rating: IP 20 (O) IK rating : IK

(P) Short circuit , Open circuit & Reverse Polarity Protection

must be provided (Q) Fixing clamp design & strength

should be sufficient to hold the fitting erected on wall or

ceiling. (R) 3 core copper wire of appropriate size with

earthing connector (Note:-The manufacturer/ authorized

Channel partner of the manufacturer has to

submit 4 yrs free replacement Guarantee for complete

Fixture) [Approval will be given strictly subject to item

specification]

Item Estimated Rate (in Rupees)

Description Of Item Qty. Unit Amount (Rs.)

No. In Figure In Words

24 Providing, erecting, testing Ceiling Fan confirming to IS: 10.00 Each 1929.00 Rupees One Thousand Nine

374/1979 AMDT No. 1 to 6 Class-I, 50 Hz. Specification of Hundred Twenty Nine Only

Ceiling Fan must be as per below. (1) Sweep: 1200 mm, (2)

Operating Voltage: 180 to 230 V, (3) Power Factor: > 0.9, (4)

Power Consumption: maximum 53W, (5) RPM: minimum

330, (6) Service value:min 4.3 m3/min. (7) Class of

insulation: 'B', (8) No. of heavy duty premium quality Ball

bearing: Two, (9) Total Body: Top & Bottom should be

alluminium, (10) Blade: Aluminium approx 1.1 mm thick, (11)

Colour: White high grade powder coating, (12) Canopy: Two

Nos. Heavy duty, (13) Condenser: Min. 1.5 MFD (15%

Tolerence) as per IS:1709-1984, (14) Down road: up to

mtr as per site requirment, (15) Required fixing accessories,

(16) 3 core 0.50 sq.mm ISI wire as per site requirment, (17)

No vibration and noise due to mechanical parts. (18) Safety

wire provided by manufacturer with ceiling fan. (Agency has

to erect safey wire with ceiling fan and checked with EIC)

(OEM has to approved model as per tender specification and

tested at ERDA)

25 Supplying and erecting approved make oscillating type 5.00 Each 2329.00 Rupees Two Thousand Three

medium duty bracket fan with Aluminium Blades A.C. 23OV. Hundred Twenty Nine Only

50cy/s wall mounted with height adjustment and rotary tilting

device complete with guard, mounting accessories kit, pull

cord for speed and oscillation flexible Core plug top complete

erected with lead wires as directed.(a) 400mm

26 Providing Fan clamp of 30 x 5 mm flat of required length & 8.00 Each 98.00 Rupees Ninety Eight Only

10 mm M.S. Bolt & Nuts erected with necessary hook of

mm M.S. Round Bar.

Item Estimated Rate (in Rupees)

Description Of Item Qty. Unit Amount (Rs.)

No. In Figure In Words

27 supplying & erecting 19/20 mm.nominal bore"B" class G.I. 10.00 Mtr. 107.00 Rupees One Hundred Seven Only

pipe/M.S. pipe down rod erected duly painted for fan

complete with necessary 24/0.2 flat 3 core flexible core with

earthing.The down rod thickness, hole, locking arrangement,

construction, powder coating, colour shed should be same as

original down rod brought with ceiling fan.For that agency has

to give original down rod sample to fabricator and one

sample down rod should be approved with EIC.After approval

given by ELC agency can use the down rod as per approved

sample.If without approval down rod will be erect on

site,agency has to replace them with own cost. (Execute if

fall ceiling occurs)

28 Supplying & erecting single phase approved make industrial 5.00 Each 2034.00 Rupees Two Thousand Thirty Four

exhaust fan suitable for medium duty ring mounted low noise Only

operation suitable for medium duty having following dia size

and maximum speed in RPM [A] 305 mm dia 900 RPM

Item Estimated Rate (in Rupees)

Description Of Item Qty. Unit Amount (Rs.)

No. In Figure In Words

29 Providing & Erecting 2.0 mtr. long Earthing system by making 1.00 Each 7025.00 Rupees Seven Thousand Twenty

minimum bore of 225 mm dia. in soft soil. Suitable for doing Five Only

pipe-in-pipe technology earthing. Earthing electric rod must

be made from Corrosion free hot dip galvanizing pipes

having following specification.

(A) Earthing Electrode: outer Pipe: - 88 mm minimum O.D.,

'B ' Class ISI mark of Reputed Brand, Inner pipe: - 42 mm

minimum O.D., Pipe B Class ISI mark reputed Brand.

Terminal Size: 70 mm X 100 mm length, Terminal should be

made from inner pipe for that pipe must be pressed and gave

rectangular shape so its work as a terminal. The hot deep

galvanising must be done after above process. Galvanised

thickness must be minimum 75 micron anywhere. SS Nut

bolt:- 2 nos. with washer suitable for 14 mm dia. hole must be

provided at terminal. Total minimum Weight (approx.) of

earth electrode with inside conductive material be 26 kg.(B)

Inner chemical (CCM Compound):- Resistivity:- 0.2 ohm/

meter testing as per IEC 62561-2017, Voltage drop:- < 1 volt

at no load & dry form, Sulphur content:- <2% (C) Back fill

Compound:- Earthing compound should be capable to retain

moisture for long time. Back Filling Compound weight is

Kg. (D) Chamber and cover:- Earthing chamber should be

size of 400 mm X 400 mm X 400 mm depth and Cover

should be heavy duty cast iron with required size of 300 mm

X 300 mm X 4 mm thick.

Item Estimated Rate (in Rupees)

Description Of Item Qty. Unit Amount (Rs.)

No. In Figure In Words

Necessary test report must be submitted.

1. Short circuit test by ERDA/ CPRI for 25KA

2. Resistivity test of conducting material from NABL

accredited lab.

3. Hot dip galvanised / zinc coating micro test from reputed

laboratory.

4. General test report from OEM regarding specification of

[Make and model approved by EIC Strictly subject to item

specification only] [OEM has to submit all detail & sample for

approved before supplying]

[Water must be poured in bore before starting earthing.

Earthing value must be measured with earth tester. Agency

has to bring the earth resistance to at least 02 ohms &

voltage between neutral & Earthing upto 02 volt. Agency has

to maintain earthing & its value for one year. Earthing must

be done in the presence of A.E. (GSPHCL)]

Item Estimated Rate (in Rupees)

Description Of Item Qty. Unit Amount (Rs.)

No. In Figure In Words

30 Providing and erecting approved make single phase Double Door metal 1.00 Each 5536.00 Rupees Five Thousand Five Hundred

clad D.B. as per relevant indian standards ammended upto date.

Thirty Six Only

Supplying and fixing following way single phase MCB distrubution board of

company fabricated IK 09 certificate with sheet box with powder coated

inside and outside after apply seven tank chemical process of MS sheet

cover complete with suitable integral single piece construction tinned

copper busbar and link with all necessary interconnection and with

necessary size MS frame for mounting MCBDB. Manufacturer must be

provided (1) IP 43 and as per IS:8623-1 & 3, IEC 61439-1 & 3 having D

type PU gasket. (2) Seven tank Powder coating Certificate (3) Tinned

Copper/Brass make neutral & Earthing link with isolation & Protecting

Cover for 240 Volts on surface / recess complete with loose wire box,

terminal connectors for all incoming and outging circuits, with suitable size

FRLS PVC insulated copper conductor up to terminal blocks and internal

connection, tinned coppper bus bar, 1 no. tinned copper neutral link, tinned

copper earth bar, din bar, detachable gland plate, interconnections,

powder painted including earthing etc. Single phase incoming and

horizontal single phase outgoing. For 16 Way MCBDB: Including 40 Amp.

30 mA double pole ELCB (ELCB confirming to IS:12640/1988 having

sensitivity of 30 mA and breaking capacity of 10 KA), MCB 40 Amp. double

pole switch (C curve confirms to IS:8828 having breaking capacity of

KA) and S.P. MCB of rating 6 to 32 Amp. with NL suitable to operate on

requirement instructed by EIC .) (The DBs should be used of same

company of MCB / ELCB to be used) (MCBDB must be erected in line &

level with spirit level and finish the external edge with box cutting plaster)

(Same colour MCB(SP/DP) should be used as same as MCBDB)

[Including Necessary numbering / marking on box done with red colour

radium sticker as per site requirement and instructions given by EIC on

site. Font / number size given by EIC on site as per requirement]

31 Providing & erecting 415 V MCB Four pole switch for motor & 5.00 Each 1104.00 Rupees One Thousand One Hundred

Inductive Load (C curve) having 10 KA breaking capacity & Four Only

confirms to IS : 8828 with M.S box having following capacity:

32 Providing and erecting 240 volt MCB double pole switch for 5.00 Each 599.00 Rupees Five Hundred Ninety Nine

Moter & inductive load(C Curve) having 10 KA Breaking Only

capacity and confirms to IS : 8828 with same company Metal

box with earthing terminal having following capacity. with

necessary quarter Numbering with oil paint by Painter. (a)

40 Amp Capacity.

Item Estimated Rate (in Rupees)

Description Of Item Qty. Unit Amount (Rs.)

No. In Figure In Words

33 Providing and erecting Approved make RCCBs conforming 1.00 Each 2213.00 Rupees Two Thousand Two Hundred

to IS: 12640 and having sensitivity of 30 mA and Short Circuit Thirteen Only

withstand capacity of 10 KA and suitable for operation on

single phase 240 V,50Hz. having characteristic of quick

action & tripping with all advance feature & do not incorporate

any electronic component. for following Max. rating erected

as directed (ii) 40Amps. DP

34 Providing & erecting Miniature circuit breaker single pole 6 2.00 Each 111.00 Rupees One Hundred Eleven Only

Amp. to 25 Amp. suitable to operate on 240 V A.C. system

and having breaking capacity 10 KA to be erected in existing

box. confirming to IS 8828/1996 with ISI Mark.

35 Supplying & fixing box for housing RCCB + MCB combination 1.00 Each 442.00 Rupees Four Hundred Forty Two Only

made of 18 SWG sheet steel duly powder coated with

gasket, dust & vermin proof bakelite shield two earthing

terminals for following type of RCCB, RCCB + MCB [b] For

36 Providing & Erecting Flexible PVC insulated multistrand 30.00 Mtr. 77.00 Rupees Seventy Seven Only

multicore 1.1 kv grade ISI marked copper wires of following

size to be erected as directed. 3 core 2.5 sq.mm. PVC

insulated round copper wire ISI mark.

Signature of Contractor Executive Engineer

GSPHCL Surat