Loading
Loading…
Loading…
Tender Value
₹5.0 Cr
EMD Value
₹4.0 L
Closing Date
27 Jan 2026, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Revenue
WORKS
16 conditions · 4 needing a document upload
Financial Eligibility Criteria :- The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB , along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
All rates are inclusive of GST and bidders should be registered in GST.
Technical Eligibility Criteria: (a)The tenderer must have successfully completed or substantially completed (Which should have been issued not prior to 60 days of date of invitation of present tender) any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited:(i) Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii) One similar work costing not less than the amount equal to 60% of advertised value of the tender.
Note for Item 10.1: Work experience certificate from private individual shall not be considered. However, in addition to work experience certificates issued by any Govt. Organisation, work experience certificate issued by Public listed company having average annual turnover of Rs 500 crore and above in last 3 financial years excluding the current financial year, listed on National Stock Exchange or Bombay Stock Exchange, incorporated/registered at least 5 years prior to the date of closing of tender, shall also be considered provided the work experience certificate has been issued by a person authorized by the Public listed company to issue such certificates. In case tenderer submits work experience certificate issued by public listed company, the tenderer shall also submit along with work experience certificate, the relevant copy of work order, bill of quantities, bill wise details of payment received duly certified by Chartered Accountant, TDS certificates for all payments received and copy of final/last bill paid by company in support of above work experience certificate
Similar nature of work:- " Any Track Work."
12 conditions · 8 needing a document upload
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
The tenderer shall clearly specify whether the tender is submitted on his own (Proprietary Firm) or on behalf of a Partnership Firm / Company / Joint Venture (JV) / Registered Society / Registered Trust / HUF etc. The tenderer(s) shall enclose the attested copies of the constitution of their concern, and copy of PAN Card along with their tender. Tender Documents in such cases are to be signed by such persons as may be legally competent to sign them on behalf of the firm, company, association, trust or society, as the case may be.(Para 14.1 (see Page-17 of GCC, April-2022) & Tenderer shall submit the documents in support of their constitution of the firm as per Para 14 of GCC, April-2022 (See Page-17 to 19).
As per instructions please attach proforma of ANNEXURE V-A this certificate is to be given by attorney/authorized signatory/each member of partnership firm / Joint Venture (JV)/ Hindu Undivided Family (HUF) / Limited Liability Partnership (LLP) etc.) Non submission of above certificate (s) by the bidder shall result in summarily rejection of his/their bid. It shall be mandatorily incumbent up on the tenderer to identify, state and submit the supporting documents duly self-attested / digitally signed by which they/he is qualifying the Qualifying Criteria mentioned in the Tender Document. Proforma is available in uploaded documents.
Certificate of Information regarding Employment/Partnership etc. of Retired Railway Employees with the tender as per the attached Performa. As per clause No 16 (a) and (b) of GCC Part-I April 2022 corrected up to date. (As per Para 16 of GCC, April2022 (See Page-19 to 20).
Restrictions on the Employment of Retired Engineers of Railway Services Within One Year of their Retirement: As per Para 59.9, of GCC, April-2022 (see Page-91).
Certificate of NO Relative being an employee of Western Railway as per attached Performa.
The tenderer should upload the scan copy of EPFO and ESI registration number. However EPFO and ESI registration would be mandatory and documents towards EPFO and ESI registration must be submitted before execution of the agreement.
In case of Bid Security in the form of Bank Guarantee, the same should be in favor of Sr. DFM Vadodara with the tender for due performance with the stipulation to keep the offer open till such date as specified in the tender, under condition of tender. (GCC April 2022 Part I Instructions to tenderers (ITT) para 5 Bid Security (1) (a,b,c),(2) (3)(i-viii). As per ACS 2 issued vide Rly. Board letter No.2022/CEI/ CT/GCC-2022/Policy date 13.12.2022: (ii) The original Bank Guarantee should be delivered in person to the official nominated as indicated in the tender document within 5 working days before closing date for submission of bids. As pr ACS 5 RB No. 2022/CE-I/CT/GCC-2022/Policy date 20.10.2023:- Para 5(3) II The original bank guarantee should be delivered in person to the official nominated as indicated in the tender document before closing date for submission of bid.(i.e. excluding the last date of submission of bids).
The tenderer whether sole proprietor / a company or a partnership firm / joint venture (JV) / registered society / registered trust / HUF / LLP etc if they want to act through agent or individual partner(s), should submit along with the tender, a copy of power of attorney duly stamped and authenticated by a Notary Public or by Magistrate in favour of the specific person whether he/they be partner(s) of the firm or any other person, specifically authorizing him/them to sign the tender, submit the tender and further to deal with the Tender/ Contract up to the stage of signing the agreement except in case where such specific person is authorized for above purposes through a provision made in the partnership deed / Memorandum of Understanding / Article of Association /Board resolution, failing which tender shall be summarily rejected. As par Para 15 of GCC, April-2022 (see Page-19).
Maintenance period for the work is "NIL Calendar" from the certified date of the completion.
BRC-GER Section:- Outsourcing of track maintenance activities under SSE (P.Way) MHD in the jurisdiction of Sr. DEN/North/ BRC.
DRM-BRC-165-OF-2025-26~WR
DRM-BRC-165-OF-2025-26
Open
Works - General
24 Months
Vadodara, Gujarat
₹0
₹4.0 L
27 Jan 2026
31 Dec 2025
13 Jan 2026
148 items across 8 schedules · ₹6,00,81,458.39 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | Up to 40 m long rail panel | RM | 4000.00 | 9.8 | 39,200 |
| 2 | More than 40 m long rail panel | RM | 4000.00 | 15.5 | 62,000 |
| 3 | For Through Rail Renewal work | TRM | 2000.00 | 48.05 | 96,100 |
| 4 | For Casual/Scattered Rail Renewal work | RM | 4000.00 | 38 | 1,52,000 |
| 5 | For Through Rail Renewal work | TRM | 2000.00 | 49.55 | 99,100 |
| 6 | For Casual/Scattered Rail Renewal work | RM | 4000.00 | 40.24 | 1,60,960 |
| 7 | For location of work not involving deep screening | Each | 2500.00 | 365.06 | 9,12,650 |
| 8 | For PSC wider base sleepers - For location of work not involving deep screening | Each | 1000.00 | 383.31 | 3,83,310 |
| 9 | Locations other than Ballasted Deck Bridge | Each | 2500.00 | 507.15 | 12,67,875 |
| 10 | Through Fitting Renewal (TFR) on PSC track, comprising of renewal of Grooved Rubber Pads, Liners and ERCs without damaging PSC sleepers. Scope includes removal of all fittings, cleaning of rail seat, rail flange at liner seats, and eye of Inserts with wire brushes and applying Grease Graphite Grade "O" (IS:408) to eye of insert and central leg of ERC with contractor's grease of Railway's specification, fixing all fittings in correct position and sealing liner edges with grease all complete including collection and stacking of released materials at nominated locations within SSE Jurisdiction as directed by Engineer-in-Charge. Note: All the fittings will be supplied at SSE/Stores/Depot. | Sleeper | 5000.00 | 35.3 | 1,76,500 |
| 11 | For 1.00m long fishplates | Joint | 500.00 | 129.19 | 64,595 |
| 12 | Opening and refixing of Joggled fish plates provided to weld joints/rail of any rail section under traffic to enable examination of weld/rail by departmental official nominated by Engineer In charge and lubrication of fishplates by applying departmental Grease graphite grade 'O' (IS:408) to fishing planes and bolts by departmental black oil as per procedure laid down in latest version of IRPWM, including all tools required and as directed by Engineer-in-charge. Note: 1. Grease Graphite, black oil, fish bolts, K.Oil, wire brush, required for work shall be given by department and issued at concerned SSE/PW Stores. 2.Jammed fish bolts shall be cut using chisel and hammer and replaced with new bolt. | Set | 1500.00 | 56.16 | 84,240 |
| 13 | Lubrication of ERCs and its liner contact area by removal of ERCs and Metal / GFN liners in rail panel, cleaning of rust / scale of ERC, Metal / GFN liners & SGCI insert by using wire brush, scrapper / sand emery paper etc supply and application of graphite grease, as prescribed by Railway for under side of liners & corresponding area of rail foot & SGCI insert with ERCs and re-fixing the same as per procedure prescribed in latest edition of IRPWM with contractors grease and all other tools & plants complete and as directed. Note: Each ERC in this item shall constitute 1 ERC and its Liner Contact area. | ERC | 450000.00 | 5.91 | 26,59,500 |
| 14 | Removing seized ERC from SGCI inserts of existing track by using suitable approved chemicals and re-fixing after greasing of insert eye and ERC with Contractor's grease of specified quality as per provisions of IRPWM, as directed by Engineer in-charge. Note: 1.List of Seized ERC along with location shall be prepared after inspection of SSE/P.Way and marked prior to execution of this item. 2. Due care shall be taken to avoid any damage to the sleeper 3.A penalty of 50% of the basic cost of new sleeper in nearest sleeper factory shall be levied on each, if SGCI insert is broken or sleeper gets cracked in the process. | ERC | 5000.00 | 54.22 | 2,71,100 |
| 15 | Lubrication of gauge face of rail on curves, cross overs, points & crossings, turn-in curves and at locations as required with contractor's grease graphite grade "O" IS 408 and as directed. | RM | 30000.00 | 5.45 | 1,63,500 |
| 16 | By using Contractor's Grease Graphite | Each | 50000.00 | 40.38 | 20,19,000 |
| 17 | GRSP | Each | 20000.00 | 22.26 | 4,45,200 |
| 18 | ERCs | Each | 40000.00 | 7.43 | 2,97,200 |
| 19 | Metal/GFN Liners | Each | 40000.00 | 4.95 | 1,98,000 |
| 20 | Renewal of seized Plate/Rail screws on PSC Sleepers by using gas or any approved methods, duly drilling holes in broken screw and removing existing screw pieces from the holes along with existing dowels and fixing new contractor's dowels (procured from RDSO approved sources) and grouting around dowel with Epoxy materials of approved specification and refixing new Railway's rail/Plate screws duly greasing the s c r e w w i t h specified grease with all contractor's materials, consumables, tools & plants, labour with all lead, lift. Note: 1.Seized screws shall be identified and marked by JE/P.Way and verified at minimum SSE/P.Way In charge) level. 2. Due care shall be taken to avoid any damage to the sleeper 3.A penalty of 50% of the basic cost of new sleeper in nearest sleeper factory shall be levied on each, if sleeper gets damaged in the process. | Each | 1500.00 | 434.73 | 6,52,095 |
| 21 | Rail section of 52Kg and above | Each | 2000.00 | 108.38 | 2,16,760 |
| 22 | Renewal of existing SEJ with improved SEJ with PSC sleepers under traffic block c o n d i t i o n s as per approved drawing including fixing of special size bearing plate, rubber pad and other sleeper / rail fittings, greasing to the fittings, leading rails, sleepers & fittings to site, leading and stacking of released materials within a lead of 250m, cutting of Rails, drilling of holes, fixing of related fittings, providing temporary connection with fishplates till welding of SEJ is done and sleepers shall be given initial packing to make track fit for 20KMPH speed. Note: (1) Rail cutting and hole drilling shall be paid separately. (2) One set comprise complete SEJ on both rails at SEJ. | Set | 20.00 | 9,223.09 | 1,84,461.8 |
| 23 | 1 in 8½ Turnout (Under Traffic Block) | Set | 2.00 | 36,162.9 | 72,325.8 |
| 24 | 1 in 12 Turnout (Under Traffic Block) | Set | 5.00 | 41,060.82 | 2,05,304.1 |
| 25 | 1 in 8½ Turnout | Set | 2.00 | 44,365.57 | 88,731.14 |
| 26 | 1 in 12 Turnout | Set | 5.00 | 49,571.49 | 2,47,857.45 |
| 27 | 1 in 8½ Turnouts | Set | 2.00 | 19,568.13 | 39,136.26 |
| 28 | 1 in 12 Turnouts | Set | 10.00 | 22,541.03 | 2,25,410.3 |
| 29 | 1 in 8½ Turnouts | Set | 2.00 | 66,633.26 | 1,33,266.52 |
| 30 | 1 in 12 Turnouts | Set | 10.00 | 76,893.24 | 7,68,932.4 |
| 31 | 1 in 8½ Turnouts | Set | 2.00 | 55,046.77 | 1,10,093.54 |
| 32 | 1 in 12 Turnouts | Set | 10.00 | 63,463.61 | 6,34,636.1 |
| 33 | 1 in 8½ Turnouts | Set | 2.00 | 19,575.8 | 39,151.6 |
| 34 | 1 in 12 Turnouts | Set | 10.00 | 25,797.81 | 2,57,978.1 |
| 35 | 1 in 8½ Points & Crossing | Set | 5.00 | 14,360.08 | 71,800.4 |
| 36 | 1 in 12 Points & Crossing | Set | 10.00 | 19,545.93 | 1,95,459.3 |
| 37 | Sleepers up to 2.85 m length | Each | 300.00 | 651.53 | 1,95,459 |
| 38 | Sleepers of length more than 2.85 m and up to 4.20 m | Each | 400.00 | 898.16 | 3,59,264 |
| 39 | Sleepers of more than 4.20 m length | Each | 300.00 | 1,416.3 | 4,24,890 |
| 40 | 1 in 8½ Turnout | Set | 2.00 | 4,076.13 | 8,152.26 |
| 41 | 1 in 12 Turnout | Set | 20.00 | 4,464.56 | 89,291.2 |
| 42 | 1 in 8½ Switch Assembly | Set | 2.00 | 14,415.9 | 28,831.8 |
| 43 | 1 in 12 Switch Assembly | Set | 5.00 | 16,058.35 | 80,291.75 |
| 44 | For 1 in 12 Turnouts | Set | 10.00 | 32,825.5 | 3,28,255 |
| 45 | For 1 in 8.5 Turnouts | Set | 5.00 | 26,260.4 | 1,31,302 |
| 46 | For 1 in 12 Turnouts | Set | 30.00 | 7,206.37 | 2,16,191.1 |
| 47 | For 1 in 8.5 Turnouts | Set | 4.00 | 5,765.1 | 23,060.4 |
| 48 | Renewal of corroded slide chairs duly removing the old slide chairs by heating using contractors gas and equipments or by any approved methods and inserting Railways new slide chairs and plate screws including crossing of tracks, leading all required materials to site, stacking all released materials, with all contractor's tools, consumables, labour, lead, lift and incidental charges etc complete as directed by the Engineer in charge. Note: 1. All the fittings will be supplied at nearest SSE/Stores. 2. In case of damage of PSC sleeper, penalty at the rate of 25% of the current cost of sleeper shall be levied. | Each | 500.00 | 389.32 | 1,94,660 |
| 49 | Turnout sleepers of length up to 2.85 m | Each | 500.00 | 147.2 | 73,600 |
| 50 | Sleepers of length more than 2.85 m and up to 4.20 m | Each | 700.00 | 176.64 | 1,23,648 |
| 51 | Sleepers of length more than 4.20 m | Each | 300.00 | 191.36 | 57,408 |
| 52 | Depth of 300 mm below bottom of sleeper - For Plain Track : | TRM | 500.00 | 623.04 | 3,11,520 |
| 53 | Depth of 300 mm below bottom of sleeper for Turnouts | TRM | 200.00 | 996.86 | 1,99,372 |
| 54 | Extra to item nos. from 081011 to 081018 and from 081021 to 081028 for disposal of muck at a distance beyond 50m for every additional lead of 50 metres or part thereof up to 500 metres for 1 TRM in station yard / cutting. | Each | 700.00 | 5.94 | 4,158 |
| 55 | Boxing and profiling of ballast as per procedure prescribed in latest edition of IRPWM including cess dressing on both sides of track. The work will include removing excess ballast from track and putting the same in crib and shoulder by leading to a maximum of 50m including crossing of track, deweeding on ballast section etc and as directed by Engineer-In charge. | TRM | 125000.00 | 28.14 | 35,17,500 |
| 56 | Under Traffic Block Conditions: | cum | 8000.00 | 56.2 | 4,49,600 |
| 57 | Unloading of sand / quarry dust during block from Railway's wagons other than Hopper wagons by opening the doors of boxes and pulling & pushing down sand with rake irons / phowrahs taking out jammed sand and distributing unloaded sand uniformly over the track. | cum | 100.00 | 119.87 | 11,987 |
| 58 | In-situ reconditioning of MCI insert of points & crossings sleeper by reclaiming the worn- out portion to the desired height, grinding of the finished profile for regaining the toe load lost. The reconditioning to be done by using TERRA C I-94 - Electrodes of make L & T, Advani Oerlicon, Diffusion, SHARP - 650, or equivalent approved by RDSO for reconditioning of Cast iron alloys. removing and refixing the required fittings for reconditioning in traffic condition. The cost includes all labour, lead lift, transportation of men and material, cost of consumables, hiring of machinery required etc, complete and as directed by the Engineer-in -charge. | Each | 6000.00 | 359.55 | 21,57,300 |
| 59 | For PSC sleeper Track with Sleeper Density of 1540 Sleepers/Km or more | TRM | 500.00 | 111.67 | 55,835 |
| 60 | For PSC Sleeper | TRM | 500.00 | 95.71 | 47,855 |
| 61 | Packing of isolated loose PSC sleepers on plain track below the bottom of the sleepers and surrounding through out its length duly opening two galas on either side of the renewed sleepers and packing the sleeper to bring the track to normal speed including gauging, aligning, squaring of sleepers and sectioning of ballast to the required profile with all contractor's labour, tools and plant etc. including all lead and lift and crossing of tracks where ever necessary complete and as directed by the Engineer-in-charge. | Sleeper | 5000.00 | 86.43 | 4,32,150 |
| 62 | For PSC sleeper Track with Sleeper Density of 1540 sleepers/Km or more | TRM | 5000.00 | 190.47 | 9,52,350 |
| 63 | With Contractor's Hydraulic Rail tensor | TRM | 1000.00 | 52.13 | 52,130 |
| 64 | Without Rail tensor | TRM | 50000.00 | 47.35 | 23,67,500 |
| 65 | With Clamps | Set | 500.00 | 166.97 | 83,485 |
| 66 | With Contractor's hard wood block. | Each | 200.00 | 1,309.31 | 2,61,862 |
| 67 | Drilling holes of 16mm to 22mm dia. on all types of PSC sleepers and fixing the dowels with adhesive of RDSO approved quality for fixing check rails & guard rails, as directed by Engineer in-charge. | Each | 200.00 | 402.37 | 80,474 |
| 68 | Cleaning of side drains along the track including disposing of muck beyond Railway boundary as per instructions of Engineer in- charge to keep drains clean and clear in cuttings etc. | RM | 15000.00 | 34.63 | 5,19,450 |
| 69 | Removing weeds & bushes in ballast section and cess up to 3.95m from centre line of track in mid section & station yard, as specified by Engineer in-charge including disposal of branches, bushes outside cess/yard. | TRM | 200000.00 | 15.94 | 31,88,000 |
| 70 | Kilometre & Gradient post | Each | 10.00 | 110.67 | 1,106.7 |
| 71 | LWR / SEJ Board | Each | 10.00 | 202.74 | 2,027.4 |
| 72 | Curve Board | Each | 10.00 | 202.74 | 2,027.4 |
| 73 | Curve details, SE, Versine, Station Nos. etc. per station. | Each | 10.00 | 63.61 | 636.1 |
| 74 | Bridge Board | Each | 5.00 | 202.74 | 1,013.7 |
| 75 | Bridge Tablet | Each | 5.00 | 55.72 | 278.6 |
| 76 | Bridge Height Gauge | Each | 10.00 | 3,547.3 | 35,473 |
| 77 | Miscellaneous General Boards, Jurisdiction Boards, Structures etc. | Sqm | 10.00 | 166.66 | 1,666.6 |
| 78 | For day time block working | TRM | 150000.00 | 20.3 | 30,45,000 |
| 79 | Removing and refixing of guard Rails over slab bridges during machine packing with all contractor's men and materials duly removing fittings, leading guard rails to bridge approaches, lifting, dragging, positioning and crossing of track etc, and as directed by Engineer In charge. | TRM | 2200.00 | 112.28 | 2,47,016 |
| 80 | 1 in 8½ Turnouts (Under Traffic Block Conditions) | Set | 10.00 | 9,996.74 | 99,967.4 |
| 81 | 1 in 12 Turnouts (Under Traffic Block Conditions) | Set | 80.00 | 11,639.19 | 9,31,135.2 |
| 82 | Derailing Switch (Under Traffic Block Conditions) | Set | 5.00 | 3,655.41 | 18,277.05 |
| 83 | 60 Kg - 110/90 UTS - Outside Track | Each | 300.00 | 242.54 | 72,762 |
| 84 | 60 Kg - 110/90 UTS - On Running Line | Each | 700.00 | 310.82 | 2,17,574 |
| 85 | Outside Track | Each | 100.00 | 61.48 | 6,148 |
| 86 | On Running Line | Each | 200.00 | 78.7 | 15,740 |
| 87 | Sleeper Spacing, Re-spacing / Squaring of sleeper by Hydraulic Sleeper Spacer with contractor's tools & plants, equipment, consumable with all lead & lift etc. complete, as directed by Engineer in- charge. Hydraulic Sleeper Spacer shall be as per RDSO's Specification No. TM/SM/17, dated 31.03.1992. | Each | 7000.00 | 75.84 | 5,30,880 |
| 88 | Measuring of Toe Load of ERC during service in field by Electronic Toe Load Measuring Device with contractor's tools & plants, equipment, consumable with all lead & lift etc. complete, as directed by Engineer in-charge. Electronic Toe Load Measuring Device will be as per RDSO's Specification No.TM/SM/ETLMD/218 dated 13.9.2012. | Each | 1000.00 | 4.69 | 4,690 |
| 89 | In wagons during period of traffic block where handling by mechanical means is not possible | MT | 100.00 | 305.76 | 30,576 |
| 90 | I n Wagon where mechanical handling is possible and traffic block is not required or in Truck/trailer. | MT | 100.00 | 216.82 | 21,682 |
| 91 | For lead up to 500 metre. | MT | 400.00 | 410.32 | 1,64,128 |
| 92 | For lead beyond 500 metre and up to 1 Km. | MT | 200.00 | 529.6 | 1,05,920 |
| 93 | From wagons during period of traffic block where handling by mechanical means is not possible | MT | 100.00 | 189.12 | 18,912 |
| 94 | For lead up to 500 metres | MT | 100.00 | 319.49 | 31,949 |
| 95 | For lead beyond 500 metre and up to 1 Km | MT | 100.00 | 474.19 | 47,419 |
| 96 | Rails, switches, crossings, SEJ, Glued Joints, Check Rails etc. | MT | 150.00 | 478.8 | 71,820 |
| 97 | All type of PSC sleepers | MT | 150.00 | 516.47 | 77,470.5 |
| 98 | P.Way fittings of all types and other similar loose items | MT | 100.00 | 414.33 | 41,433 |
| 99 | Level crossings with asphalted road surface | Sqm | 3000.00 | 607.68 | 18,23,040 |
| 100 | Level crossings with concrete blocks road surface | Sqm | 320.00 | 551.86 | 1,76,595.2 |
| 101 | Fabrication including cutting, bending/machining and fixing of check rails of all rail sections over PSC Sleepers as per Railway's approved drawings & specifications for level crossings / trolley paths/inspection lines in yards duly cutting rail flanges, wherever required to correct alignment and level, drilling of holes with machine in check rails and fixing to Running rail and sleepers with all Railway's fittings, e.g. rail screws / grip expansion bolts, brackets, packing pieces, bolts, washers etc including grinding of brackets if required, fixing of Railway's wooden blocks at flare ends duly cutting and plaining, crossing of tracks and as directed by the engineer in- charge Note: 1. Drilling of holes in PSC Sleeper and fixing of dowels shall be paid under relevant item. 2. Required P.Way materials will be supplied at SSE/P.Way stores. | TRM | 500.00 | 1,218.23 | 6,09,115 |
| 102 | Fixing check rails to running rails on level crossings with MS brackets, MS packing plates, bolts & nuts, spring washers etc. including lubrication as per approved drawing & specifications, as directed. Rails, MS brackets, packing plates, bolts & nuts, spring washers will be supplied by Railways. Note: One set consists two check Rails. | Set | 100.00 | 5,368.47 | 5,36,847 |
| 103 | Renewal of existing running rail and guard rails of all sections on bridge portion over Steel Channel sleepers/PSC sleepers under traffic block including leading of new rails, fittings, refixing all the fastenings as per approved drawings including cutting of rails, drilling of holes to running and guard rails as required as per drawing and leading back the released rails and fittings and stacking at nominated place clear of infringements with all leads & lifts tools and consumables complete and as directed. | TRM | 500.00 | 784.29 | 3,92,145 |
| 104 | Involving Rubber Pad | Each | 100.00 | 62.55 | 6,255 |
| 105 | Not involving Rubber Pad | Each | 300.00 | 34.64 | 10,392 |
| 106 | Manufacture of flared portion of Guard Rail by cutting and bending to required shape & RDSO's approved drawings. Note: (1) Rails shall be supplied by Railways. (2) One set consists of two rails i.e. both left and right. | Set | 8.00 | 4,798.73 | 38,389.84 |
| 107 | Providing and fixing of flared portion of guard rails of any rail section over PSC sleepers including fixing of with all fittings, including leading of rails and fittings, squaring and adjusting spacing of sleepers as required, providing nose blocks duly cutting wooden blocks supplied by railways and fixing it with bolts of 16mm dia as directed complete and finished as per RDSO's approved drawing. Note: 1.One set consists of LH & RH side rails of one end. 2.Required P.Way fittings will be supplied at SSE stores depot. | Set | 8.00 | 3,922.16 | 31,377.28 |
| 108 | Drilling holes 25mm to 40mm dia. with drill twist in the foot of guard rails for fixing guard rails on bridge as directed. | Each | 100.00 | 71.71 | 7,171 |
| 109 | Drilling of 25mm to 40mm dia. holes in PSC sleepers with suitable rotary hammer / drilling machine at indicated location for fixing of guard rails on bridges & its approaches as per approved drawing and fixing of contractor's HDPE dowels and adhesive of approved quality to Drawing no. RDSO/T-3002, procured from RDSO's approved sources with contractor's materials and consumable. | Each | 100.00 | 409.94 | 40,994 |
| 110 | Dismantling of existing flared portion of guard rails of any rail section over PSC sleepers duly removing rails & fastenings and leading and stacking released materials at nominated place within free lead, clear of infringements, complete and as directed. Note: One set consists of LH & RH side rails of one end. | Set | 10.00 | 2,186.52 | 21,865.2 |
| 111 | Clearing waterway of major & minor bridges by removing weeds / shrubs / bushes, removing silt deposit, filling scours, if any up to 10 metre from centre of bridge on either side including disposing waste and silt away from waterway. Note: Rate is for a single line and per metre of bridge span. | Metre | 1000.00 | 228.69 | 2,28,690 |
| 112 | Overhauling of track on ballasted deck slab bridge i.e. screening of crib ballast and shoulder ballast in between sleeper ends and ballast retaining walls on both sides of the track without disturbing core under the sleeper under traffic following all safety precautions and other instructions prescribed by Engineer in-charge. Muck should be disposed of away from bridge up to a maximum distance of 350 m and lift up to 10m. | TRM | 1100.00 | 336.44 | 3,70,084 |
| 113 | Tightening of steel channel sleeper fittings i.e. hook bolts, running rails bolts, guard rail bolts on girder bridges with contractor labour tools, plants etc., including oiling, greasing of fittings complete and as directed by engineer in charge. Note: Before execution of work specific approval of ADEN to be obtained by duly indicating the locations with specific reasons along with date of last tightening done. | Sleeper | 400.00 | 46.4 | 18,560 |
| 114 | Single Strip / Double Strip Level Crossing Road Warning Board of size 900 mm equilateral triangular shape and 900x300 board with back support frame welded to vertical post of MS T section of size 80mmx80mmx8mmx3650mm | Set | 40.00 | 8,054.09 | 3,22,163.6 |
| 115 | Caution Indicator Board of size 1400mmx400mm with back support frame fixed to vertical post of MS angle of size 50mmx50mmx6mm of 3650 mm long | Each | 20.00 | 6,908.11 | 1,38,162.2 |
| 116 | Speed Indicator Board of equilateral triangular shape having each side of 1000mm with back support frame fixed to vertical post of MS angle of size 50mmx50mmx6mm of 3650 mm long | Each | 20.00 | 5,917.1 | 1,18,342 |
| 117 | Termination Indicator Board of Circular shape having diameter of 1000mm with back support frame welded to vertical post of MS angle of size 50mmx50mmx6mm of 3950 mm long | Each | 20.00 | 8,361.59 | 1,67,231.8 |
| 118 | Manufacturing, supplying and fixing Curve Indicator / Point Indicator / SEJ Boards to be provided at various locations on formation, made out of MS sheet 2mm thick of size 450mm x 300mm duly fixed with MS frame of 25mm x 25mm x 3mm angle welded to 50mm x 50mm x 3mm MS angle, 1000mm long post split and bent 100mm at bottom end with all lead & lift as per specification and including painting of details with enamel paint, as directed by Engineer in- charge (Earthwork & concreting will be paid separately) | Each | 50.00 | 1,171.89 | 58,594.5 |
| 119 | Supply of Used Lubricating Oil of approved quality | Litre | 2500.00 | 28.71 | 71,775 |
| 120 | For erection | Each | 50.00 | 272.4 | 13,620 |
| 121 | For removal | Each | 50.00 | 223.3 | 11,165 |
| 122 | Supply and fixing in position pre-cast cement concrete Fouling Mark as per approved drawing at station yard, duly painting the top surface and slopes with white enamel paint in two coats and inscribed letters with black of Fouling Mark, complete in all respects with all labour, materials including cement, tools and plants etc. | Each | 20.00 | 525.14 | 10,502.8 |
| 123 | Providing and fixing Trolley Refuge of size 3.0m x3.0m on cess, placing with released unserviceable PSC sleepers and keeping them at all four sides of refuge and also placing as matting inside the refuge by keeping them in upside down position with a minimum of 14 sleepers including levelling with earth, excavation, all lead and lift, crossing of tracks, leading the sleepers with in a free lead and lift, handling etc., with all contractor's men material complete and as directed by the Engineer-in-charge. Note: Earth-work will to be paid separately under relevant item. | Each | 30.00 | 4,788.41 | 1,43,652.3 |
| 124 | Supplying and spraying in specified proportion Weedicide Chemical, capable to kill entire weed on track / cess / embankment with all labour, material, tools & plants etc. complete job in all respect. Scientific name of the chemical is Isopropylamine Salt of Glyphosate, in which active ingredient is Glyphosate (41%), colour is light amber to brownish, very low in toxicity and has favourable environmental characteristics. It will be ensured that no weed growth occurs up to six months period, otherwise re-spraying shall be done by the contractor free of cost. | Sqm | 150000.00 | 0.96 | 1,44,000 |
| 125 | JCB Backhoe Loaders 3DX Plus or similar with minimum 1.10 cum bucket capacity | Hour | 1500.00 | 846.09 | 12,69,135 |
| 126 | Hydra or similar tyre mounted Pick-n-Carry crane of 12T capacity for misc. works of handling of material | Hour | 1200.00 | 2,118.4 | 25,42,080 |
| 127 | Tractor with Trolley for local transportation or other misc. works. | Hour | 1600.00 | 599.84 | 9,59,744 |
| Schedule total | ₹4,68,48,679.69 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
DRMBRC165of2025-26C.pdf
ATTACHMENT
Annexure-F.pdf
ATTACHMENT
JPOSTDepartment.pdf
ATTACHMENT
PCECircular88forQualityofWorks.pdf
ATTACHMENT
IRSGCCApril-2022.pdf
ATTACHMENT
AdvancecorrectionslipNo01to10GCCApril2022.pdf
ATTACHMENT
ImplementationofContractore-MB.pdf
ATTACHMENT
Annexure-VIB.pdf
ATTACHMENT
165SpecialCondition.pdf
ATTACHMENT
DainikkaaryanishpaadananumatipatraLetter.pdf
ATTACHMENT
02LETTERFORWORKSITESAFETYWITHAGENCIESLIKERVNLDFCCIL.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .