UPHC GRANT

Supply and fixing Aluminium Powder coated/Anodised Doors - Double Shutter as per approved drawing with aluminium powder coated/anodised sections of Jindal sections and outer frame top horizontals & both verticals of 2408 of size 101.6 x 44.75 x 3.18 mm, Shutter frame top, bottom and verticals of 4504 of size 44.45 mm x 47.62 mm x 3.18 and Middle lock rail of 4621 of size 49.91 x 44.45 x 3 mm with 8.0mm thick Toughened plain glass fixed including supply and fixing Heavy duty mortise lock 6/7levers (IS:2209) with PC or CP handles complete set, floor springs/ hydraulic door closure assembly and all labour charges for fixing the fixtures with required no.of screws, bolts and nuts and including labour charges for fixing the frame in position, fixing shutter to frame etc. completed for finished item of work. Door Size - 1.5m x 2.4m.

Supply of (7 to 9)W LED. Lamp with input voltage 90 to 300V, Color temperature 3000k - 6500k, Beam angle 170 - 220 degrees, B22 base(MAT-03287) Makes: Phillips /Crompton / Bajaj / Havells / Halonix/GM/HPLSyska / Green Lites / Fortune Arrt / GoldMedal / Luker/Leo/Orbit /Rhino / GLO LED/Million/Victoria/Benlo/Goldwyn.

Supply of 48" (1200mm) Sweep 5 star rated BLDC (Brush less Direct Current) Ceiling Fan with double ball bearings, input voltage 230V AC converted to 24 V DC, power input not more than 30W, air delivery not less than 220 cubic meter/min and a minimum service value of 7.0, with remote and without Regulator (MAT-05508) Makes: Phillips /Crompton / Bajaj / Havells / Halonix/GM/HPLSyska / Green Lites / Fortune Arrt / GoldMedal / Luker/Leo/Orbit /Rhino / GLO LED/Million/Victoria/Benlo/Goldwyn.

Manufacturing and Supply and delivery of Unplasticised PVCs pipes for potable water supplies conforming ti IS:4985/2000(third revision) with bell ends (socket) as per specification in light Grey/Natural Lvory Grey/Any other Color (except White) inclusive of transporation to the sub -divisional stores anywhere in AP including Excise duty and Sales Tax etc. 110 MM DIA 6 KG/CM2

Supply and delivery of UPVC fittings conforming to IS:4984-1995 including transportation to Any Where in A.P. Excluding excise duty,sales tax and specials etc complete

110 mm dia - Double Tee - UPVC/SWR Pipe fittings

110 mm dia - Coupler - UPVC/SWR Pipe fittings

110 mm dia - Single Tee - UPVC/SWR Pipe fittings

110 mm dia - Door cap - UPVC/SWR Pipe fittings

Painting with Synthetic Enamel paints - Two Coats - For New Iron Work

VRCC M- 20 Nominal mix (Cement:fine aggregate: coarse aggregate) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work, but excluding centering, shuttering etc., complete and as direct

1. Add GST @ 18%

2.Seignorage Charges

Note : The contractor should engage Technical personel during execution of work failing which necessary amount will be deducted from the contractor bill. The labour cess @1% shall be deducted from the contractor's bill without adding to the workdone as per the Government orders. The 3rd party QC charges shall be deducted from contractor bill from out of over head charges loaded in data.

Cutting road surface including stacking of excavated materials for pipe line trench work. a) Cutting open C.C. road surface.

Cutting road surface including stacking of excavated materials for pipe line trench work. b) Cutting open BT road surface.

Excavation for pipe in soil with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross-sections, and transporting to the embankment location with all lifts and lead upto 1000 m as per Technical Specification Clause 302.3 MORD / 301 MORTH. (RBR-EECD-5-iii)

Earthwork in excavation for Pipeline as per drawing and technical specification clause 305.1 including setting out construction of shoring and bracing. Removed of stumps and other deleterios material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material as per technical specification 305 MORD/304 MORTH (ordinary soil using manual means)

Manufacturing and Supply and delivery of Unplasticised PVCs pipes for potable water supplies conforming to IS:4985/2000(third revision) with bell ends (socket) as per specification in light Grey/Natural Lvory Grey/Any other Color (except White) inclusive of transporation to the sub -divisional stores anywhere in AP excluding Excise duty and including Sales Tax etc. 200 mm Dia PVC pipes 10kg/cm2

Lowering, Laying, Jointing and testing to hydralic test pressure including cost of water with minumum water lead of 50m for UPVC pressure pipes in ready made trenches true to alignment and gradient including all sundries but excluding cost & conveyance of pipes from source of supply and jointing materials as per BIS No.7634- Part III - 1975 . 200 mm Dia PVC pipes 10kg/cm2

Collection and supply of filling sand including cost and conveyance at site of work and labour charges for spreading , watering and ramming etc.., complete ( clause 305-89 MORD and 304 MORTH)(RBR-F NDN-2)

Supply and delivery of 110 mm x 90mm Tee - UPVC/SWR Pipe fittings

Supply and delivery of 110 mm dia PVC End caps

Supply and delivery of 110 mm dia PVC bends

Manufacture, Supply and delivery of DI D/F Gate Valves (Soft Seated) Resilient seated softsealing gate valves (Sluice valves) with bodybonnet of ductile cast iron of grade GGG40/ SG 400/12 or equivalent grade as per I.S.3896-part2- 1985 and subsequent revisions, wedge fully rubber lined with EPDM food grade quality and seals of NBR and the valves should be of vacuum tight and 100% leak proof with face to face dimensions as per BS5163-89/IS14846- 2000/DIN 3202 F 4. All the valves should be with Electrostatic powder coating both inside and outside pocket less body passage. Drilled as per IS:1538.

1. Add VAT @ 5%

2. Labour Cess @ 1%

Note : The contractor should engage Technical personel during execution of work failing which necessary amount will be deducted from the contractor bill.