PROVN OF GUARD ROOM AT MAIN GATE ALONGWITH TOILET AND BATHROOM FOR GUARD (1 AND 6) AT 811 ENGR REGT ONGC(TA) UNDER GE (A) VADODARA.

Amount

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in Soft/loose Soil

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil.

Excavation in trenches, n exc. 1.5 m wide and exc 1.5 m and not exc. 3m in depth in depth for foundation etc or not exceeding 10 sqm on plan and getting out in of soft soil complete all as specified and directed.

M & L for anti termite treatment work by treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured)complete all as specified & directed

M & L for anti termite treatment work by treating the top surface of filled earth under floors at the rate of 5 litres of emulsion per square metre of surface

M & L for anti termite treatment work bytreating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall

M & L anti termite treatment work by treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified & directed

M&L Sand filling under floors or in foundations including watering and consolidation well ramming in layers not exc 25 cm for floor,interlocking paver block or sand cushioning for cable protection etc. and all as specified and as directed.

M & L Cement concrete 1:4:8 type D2 using 40 mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm and all as specified and as directed.

Removing excavated material exc 250m but not exc 500m and depositing where directed at a level n exc. 1.5 m above the starting point and all as specified and as directed.

M & L TMT Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

All as per item No 12 herein before but 6mm to 8mm dia.

All as per item No 12 herein before but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders

M & L for RCC- M-25 (design Mix) Using 20mm graded stone aggregate for foundations, including rafts, footings, foundation beams; plinth beams; basesfor columns, etc.; basement slabs, under-reamed piles and mass concrete and all as specified and as directed.

M & L for RCC- M-25 (design Mix) Using 20mm graded stone aggregate as in Columns, pillars, piers, posts and struts and mass concrete and all as specified and as directed.

M & L for RCC- M-25 (design Mix) Using 20mm graded stone aggregate as in Chajja and mass concrete and all as specified and as directed.

M & L for RCC- M-25 (design Mix) Using 20mm Graded Aggregate as in roof beam, beams, cantilevers, bressummers, lintels over 1.5m span and all as specified and as directed.

M & L for RCC- M-25 (design Mix) using 20mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and all as specified and as directed.

Use and waste of formwork for rough finished flat surfaces of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work;

Use and waste of formwork for rough finished flat surfaces of pillars, posts, struts, piers, columns and stanchions

Use and waste of formwork to sides and soffits of rough finished floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc.

Use and waste of form work for rough finished surfaces of concrete measured flat for Chajja

Use and waste of form Work for rough finished flat surfaces to soffits and suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping)

M&L brickwork with sub class ‘B’ bricks straight or curved on plan exc 6 m mean radius built in CM 1:6

M & L brickwork with sub class ‘B’ bricks, straight or curved on plan to anyradius in half brick thick walls built in CM 1:4

M & L rendering 10 mm thick on fair faces of brick work or concrete surfaces of wall in cement mortar 1:6 for finished even and smooth (without using extra cement)

M & L rendering in two layer on fair faces of brick work or concrete sur-faces of wall 5 mm thick in CM 1:4 mixed with WPC as per manufacturers instructiion for finished even and smooth without using extra cement over 10 mm thick rendering in cement mortar 1:6 (WPC will be measured and paid separately as supply only).

M & L rendering 5 mm thick on fair faces of brick work or concrete sur-faces of ceiling in cement mortar 1:3 for finished even and smooth (without using extra cement)

Supply only water proofing compound (liquid type) all as specified and directed.

M & L for preparing new plastered surfaces of wall and applying two coats of oil bound distemper over and including a coat of 2mm average thickness wall care putty and one coat of primer all as specified and as directed.

M& L for applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.

M&L for preparing new plaster surface and apply three coat of white wash on wall complete all as specified.

M & L for preparing new plastered surfaces of ceiling and applying three coats of white wash.

M & L cement concrete type B1, 1:2:4 (20 mm graded stone aggregate) as in coping, bed plate for hold fast or as in roof kerbs or mud stops, rounded or chamfered on edges etc.

M&L for 40mm thick factory made flush shutters, solid core construction, with block board core and plywood face panels, comercial type with 1.0mm thick (veneered on both side) complete all as specified and as directed.

S & F 35mm thick 2nd class hard wood glazed and skelton shutters, open rebated and prepared to receive glass, gauze etc squares with sash bar of framing plain, chamfered or rounded, fitted with cut ,mitered and moulded beads for securing glass etc, sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a); supplied and fitted to chowkats.

S & F for mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening conforming to Fe.290.Gde-E-165 and fixing complete

M & L mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework (caging) of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and directed

M & L for preparing new steel surface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer.

M & L for preparing new wooden surface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer.

S&F Second Class hard wood plain, solid, straight as in chowkat and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed .

S&F continuous piano hinges brass bright finish or electro galvanished width of flabs when open in 30 mm

S&F 18mm thick HDHMR BOARD exterior grade including any coloured prelaminated sheet of required thickness over HDHMR board, anti fungal, moisture resistance, anti borer as per IS 14587 for frame and shutter for kitchen cabinets/cupboards etc all as per specified and directed by Engr-in-charge. Note: sample as approved by GE. Make: Action Tessa/Greenply/Century.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made all as specified and directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary SS screws shall be paid separately).

S & F 200mm long aluminium anodised barrel tower bolt of extruded section and fixed with screws.

S & F 150 mm size extruded aluminium alloy handles, fabricated type anodised fixed with screws.

S & F 300 mm aluminium alloy anodised sliding door bolts, with hasp and staple (bolt type) not less than 12mm dia with and and fixing clips of sheet cast or extruded section and fixing bolt and sliding bolt of extruded section or cast aluminium and fixed to wooden door shutters

S & F floor door stopper of aluminium alloy body and tongue, overall length of cover plate 140mm anodised with hard drawn steel spring, fixed in floors complete all as specified and directed.

M & L for 100mm butt hinges of stainless steel grade 202, 14 gauge thickness, medium weight of approved make fixed with pressed steel door frame/Angle iron door frame with screw complete all as specified and directed.

S&F steel helical door spring 300mm ordinary rat tail rod pattern springs including roller plate complete all as specified and directed.

M&L for 75mm butt hinges of stainless steel grade 202, 14 gauge thickness, medium weight of approved make fixed with pressed steel door frame/Angle iron frame/PVC door frame with screw complete all as specified and directed.

S&F Hasp and staple 150 mm long Aluminium anodised including bolt to hinge plate and fixed with screws completeall as specified and as directed

S& F Brass Hat and coat hooks, solid body, 175mm to 250 mmcomplete all as specified

S&F 25mm dia stainless steel tubular curtain rod not less than 0.90 mm thick and fency type socket fixing with brackets, stop, rollee etc co 1 mm thick mplete all as specified and directed. Note: design of socket shall be approved by GE/AGE at the time of execution)

S & F Mild steel bands, straps, supports or stays for rainwater, ventilating pipes, including bolt, if required hooks (stay), heavy for large gates, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps hold fasts, wall ties, hooks for hanging fans, plain angles cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe 310-O or Fe 410-O

S & F of Powder coated aluminium frame (Minimum coating 50 micron) for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S & F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of sliding, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge .

S&F 4.00mm thick figured glass, pin head type and glazing with rubber beading or with glazing clips n exc 0.5 sqm each pan, all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples.

M & L hardcore of broken stone guage exc 63mm but n exc. 100 mm, deposited, spread and levelled In layers n exc. 15 Cm Thick, Watered And Rolled/rammed To A True Surface

M & L cement concrete 75mm thick 1:4:8 type D2 (using 40mm graded stone aggregate) as in sub base to floor.

M & L cement concrete 25mm thick 1:2:4 type B1 (20mm graded stone aggregate) as In sub base to floor

M & L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including screed bed or bedding layer of mortar 15 mm thick for laying floor finishes with CM 1:6

M & L for Machine cut Kota stone slab 12 to 15mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade including rendering for vertical surface of wall or concrete surfaces including 10mm thick in CM 1:4 cement plaster to receive Kota stone.

M&L Granite (of any type and colour) work (table rubbed and polished) 18 to 20mm thick in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match complete all as specified and directed.

M&L for rounding to edges of stone slabs such granite or marble as steps,cooking platform and other similar situations complete all as specified.

M&L for non skid coloured ceramic tile 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38sqm , as in floors etc set over and including screed bed or bedding layer of mortar 15 mm thick for laying floor finishes with CM 1:4 including necessary adhesive (Tile pattern and decoration may be as suggested by Engineer-in-charge)

M & L for Glazed ceramic coloured walls tiles in vertical surfaces 300x450x 6mm to 7 mm thick set over and including 10 mm thick rendering on vertical surface of wall or concrete surfaces in CM 1:3 to receive wall tiles including necessary adhesive (Tile pattern and decoration may be as suggested by Engineer-in-charge).

M & L for 75 mm thick PCC 1:3:6 mix type C2 using 40mm graded stone aggregate as in paving finishing cone surface (plinth protection) even and smooth without using extra cement.

M&L for 50 mm avg thick PCC padding in cement concrete type B0 (1:2:4) using 12.5 mm graded stone aggr mixed with WPC as per manufacturer instructions finished surface even and fair for laying of WPT all as specified and directed. (WPC will be measured and paid separately as supply only).

M&L for water Proofing treatment to roof slabs by applying one coat of bituminious/polymerized primer confirming to IS-3384 @ 0.40 Ltrs/Sqm, 3 mm thick APP modified polymeric membrane of weight of 3 kg/sqm with non-woven polyester reinforcement shall be laid over a coat of bitumen S-35 grade (30/40) applied @1.20Kg /Sqm (minimum) with minimum 75 mm side overlaps and minimum 100 mm end overlaps, joints & overlaps shall be sealed with torch application and applying one coat of aluminium paint @ 0.11 Kg/Sqm over APP membrane complete all as specified and directed by Engr-In-Charge (Note: the primer and the membrane to be used shall be of the same manufacturer and to be applied by authorized applicator of OEM).

M & L 10mm thick rendering on roof in CM 1:3 mixed with WPC as per manufacturer's instructions finished even and smooth without using extra cement over PCC surface for laying APP membrane on roof (WPC will be measured and paid separately as supply only).

S&F 1000 ltrs rotational moulded polythene water storage water tanks three layered construction ( cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I duly ISI Marked, 20mm dia GI light grade over flow pipe approx length 1.5m long, 20mm dia GI medium grade pipe for wash out approx length 2.00 m duly plugged at one end shall be provided complete all as specified.

S & F 20 mm outer dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed

S & F 25 mm outer dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed

Cutting chases in brick walls for concealed water tubing etc and making good to facing in CM(1:3) cutting chases n exc 10 cm girth complete all as specified and as directed

S& F 20 mm bore dia stop valves, cast copper alloy, fancy type, chromium plated with long shank and cup (concealed type) screwed both ends for iron pipe or for unions and fixed complete all as specified

S & F stop valves/angle valve 15mm bore fancy type chromium plated screwed both ends for iron pipe or for unions and fixed

S & F 25mm dia bore gun-metal, globe or gate valves with iron wheel head screwed both ends for iron pipe and fixed

S&F 32 mm bore low density polyethylene pipe (LDPE) of pressure rating 6 Kgf/cm2 as in waste pipe

S & F Ball brass valves, for 25 mm bore of pipe high pressure, with polythene float and fly- nut complete, screwed for iron pipe or brass ferrule and fixed

S&F vitreous China squatting pan ' orrissa pattern ' size 580 x 440mm white with intergal foot rest etc complete with concrete all as specified and directed by Engg-in-Charge.

S&L for Vitreous china half stall type urinal, bowl complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugss with and including 60mm long brass screws, pointing around urinal back in cement; including S&F C.P push button stop cock & C.P spreaders connected with PVC connection to urinal. (Exclusive of fixing supply pipe to flushing button, trap and waste pipe complete all as specified and directed.

S&F Vitreous China Urinal partitions slabs terminating about 40cm above floor line, fixed plugss with and including 60mm long brass screws, pointing around complete all as specified

S & F 110mm PVC (SWR) WC connector with lip ring all as specified and as directed.

S&F PVC flushing cistren low level, 10 ltr capacity with syphonic action type ball valve. Incl inlet ball valve, PVC band (flush pipe) 32mm complete all as specified.

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S&F vitreous china under counter basin oval type ivory coloured size (550mm X 400mm) including CP waste coupling ,PVC waste pipe 32 mm dia bore and fixed in 18 mm thick polished granite all as specified and as directed. Note: (Granite top shall be measured and paid for separately under respective item of this schedule).

S&F 15mm size fancy type chromium plated brass Single lever Basin mixer with popup waste system & 450 mm long braided houses complete all as specified and as directed

S&F 15mm dia bore brass CP fancy type wall mixer with connector for hand shower arrangement with connecting legs wall flanges and wall bracket for hand shower complete all as specified and as direcred.

S&F brass Chromium plated over head shower 200x200 mm square shape single flow (ABS body chromium plated with grey face plate with rubit cleaning system complete all as specified and as direcred..

S & F Sinks made of stainless steel 1mm thick or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified.

S & F PVC connections 15mm size with PTMT nuts of length 450mm

S & F PVC connections 15mm size with PTMT nuts of length 600mm

S & F for 15mm bore brass chromium plated fancy type bib tap long body, screwed down, high pressure for iron pipe or for brass ferrule

S & F for 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors all as specified and as directed.

S & F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall all as specified and as directed.

S & F 110mm bore PVC (SWR) bends any radius all as specified and as directed.

S & F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall all as specified and as directed.

S & F 75mm bore PVC (SWR) bends any radius all as specified and as directed.

S & F 75mm bore PVC (SWR) bends any radius with oval access doors all as specified and as directed.

S & F 75mm PVC (SWR) floor trap, plain including jointing with solvent all as specified and as directed.

S & F stack clamps made out of 50mm by 5 mm mild steel flat iron and 16mm dia round iron stays incliding bolts and nuts and securing ends of stays to walls and roofs for 110mm bore pipe all as specified and as directed

S & F stack clamps made out of 50 mm by 5mm mild steel flat iron and 16mm dia round iron stays incliding bolts and nuts and securing ends of stays to walls and roofs for 75mm bore pipe all as specified and as directed

S & F 110mm PVC (SWR) vent cowl all as specified and as directed

S & F 75mm PVC (SWR) vent cowl all as specified and as directed

S & F 110mm PVC (SWR) junction single, (Single T type) equal or unequal all as specified and as directed.

S & F 75mm PVC (SWR) junction single, (Single type T) equal or unequal all as specified and as directed.

S&F mild steel CP soap dish fixed to wall with brass chromium plated screws complete all as specified and directed.

S&F glass shelf with chromium plated guard 600mm long fixed with screws complete all as specified and directed.

S & F 20mm dia brass chromium plated tubular towel rail fixed with screws 450mm long complete.

S& F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and as directed.

S&F grating 150mmx150mm made out of stainless steel fixed with gully/floor trap complete all as specified and directed.

M&L for Cement concrete type C-2 (1:3:6) (40 mm graded stone aggregate) as in foundations, filling and mass concrete or in surface channel and drain.

M&L Brickwork with sub class ‘B’ bricks straight or curved on plan exc 6 m mean radius built in CM 1:4

M&L rendering 15mm thick on fair faces of brick work or concrete surfaces with CM (1:4) finished even and smooth neeru finish Using extra cement

M & L for prepolished chequered cement concrete tiles machine pressed 30cm x 30cm x 25mm thick, over cement screed base 15 mm thick in cement morter 1:4, set, jointed and pointed in neat cement slurry in floors etc complete as directed.

M&L for Providing precast cement concrete type B1, 1:2:4 (using 20 mm Aggregate) as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including chamfers, weatherings, throat- ing etc. and setting in mortar complete with joints to matchcomplete all as specified and directed. (reinforcement shall be measured and paid separately)

M&L for factory made rubber moulded interlocking paver block any shape and confirming to IS 15658-2006 of 60mm thick, M-35 Grade laid in floor complete all as specified.

Cutting in to existing manholes for connecting new drains for 150/200mm dia pipe and making good to pipe and rendering and cut out existing benching for and forming branchchannel (1/2 round or 3/4 section ) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required for150/200mm internal dia of pipe.

M&L for Concrete bed to drain pipes 200 mm bore including packing under and haunching against the sides of pipes after they are laid and tested in cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate complete.

M&L for UPVC (SWR) 200mm dia pipes for sewage line jointed with existing SGSW/RCC/AC pipe line complete all as specified and directed.

M&L for concealed point wiring with 1.5 Sqmm PVC-FRLS insulated, sheathed, copper conductor, stranded 1100 volt grade cable in & incl PVC conduit 20mm dia, including modular metal flush boxes & modular white cover plate with frame as per site requirement all fittings such as tees, bends, elbows, etc. of External diameter 20mm all as per site requirements PVC insulated & sheathed 1100 volt grade copper conductor PVC FRLS, stranded 1.5 sqmm. cable as continuous earth lead complete all as specified and directed by Engr-in-charge for the followings:-

For one light, fan point controlled by one switch

For one 5 Amp independent socket point controlled by one switch

For one 3 pin ,5 Amp socket point with other switch on the same board

All as per item No 127 here in before but power point wiring using with 2.5 sqmm PVC-FRLS insulated ,sheathed, copper conductor stranded 1100 volt grade cable and 2.5 sqmm PVC insulated ,sheathed, copper conductor stranded 1100 volt grade cable as continuous earth lead complete all as specified and directed by engir in charge.

S&F Modular switch, one way, 6 Amp 230, 1 module.

S&F socket Modular 6 Amp-2/3 pin combined 2 module

S&F switch Modular, single pole, one way,16 Amp ,1 module 230 Volt

S&F socket modular 6/16 Amp, 2/3 pin combined ,2 module 230 Volt .

S&F ceiling rose, surface backlit,three terminal.

S&F Modular lamp holder insulated with back plate suitable for Angle/Batten fitting

S&F modular step regulator 120W, 2 module for fan.

S&F testing and commissioning of MCB SP 6 Amp to 36 Amp 240 Volt 10 KA capacity having C-curve characteristics connected with suitable lugs. Make Legrand/ L&T/Havells

S&F sheet metal enclosure for DB double door, IP-43 when MCBs to be used SPN, 8 way, 240 V with 200 Amps rated bus bar .Note :- Cutting and chasing in stone masonary and making good to disturbed surfaces will be including in item rate .

S&F testing and commissioning of MCB SPN 240 volt 16 Amp to 40 Amp 10 KA capacity having C-curve characteristics connected with suitable lugs .

Supply and fixing LED lights fitting 1x 20W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

S & F of LED street light coolwhite fitting 25 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection including bracket made out of GI pipe light grade 32mm bore not less than 1.20m long bent to shape required fixed to pole with suitable size 2 Nos clamps made out of 25X3mm flat iron with nut, bolts and washers complete all as specified and directed by Engr-in-Charge. (highly efficient LED street light made of pressure die cast aluminium housing with high power LEDs, Lens & toughened glass, IP66 and model no HLSLD-09H-25-CWL-R or equivalent model as per specified in list of makes)

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers including making hole in stone /brick wall grouting &making good in all aspects all as specified and directed. Make - Havells Ventil Air-DS/Bajaj MAXX AIR/Crompton or equivalent model as per specified in list of makes.

Supply and fix ceiling fans, white five star rating complete with three blade, down rod, accessories 230V, 1200mm sweep, with Squirrel cage induction motor.

M&L for provn of Earthing complete with galvanised steel earth plate electrode, 600x600x6mm buried directly in ground (Earth pit not less than 2.25M deep below the GL) with top edge not less than 1.5 metres below ground level connected with galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts & washers of GI or steel all as shown in electric plate no 3 connected to earthing test point all as specified or indicated including testing on completion.Note :- (i) The rate quoted shall also deemed to include the cost of GI wire and protection pipe upto 7.5 Mtr beyond the earth plates electrode and also the cost of the Test point. (ii) Joining of GI earth wire with pipe of the test point shall be done by using suitable cable lugs.

M&L for GI pipe bracket of size 40 mm dia medium grade of length not less than 1.5 Mtr long and bent to a shape incl fixing wall with 02 Nos MS flate clamp of suitable size incl nut bolt and washers complete all as specified and as directed.

M&L for the GI tubing of size 40 mm bore, medium grade, ISI marked with all GI fittings (medium grade) incl laid in trenches , floor etc complete all as specified and directed .

S&F the Gun metal Gate valve iron wheel head both end screwed of size 40 mm bore for iron pipe approved all as specified and directed.

Supply and laying in trenches or passing through pipe, 1100 volts grade heavy duty cable with XLPE insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 25 sq. mm 4 Core nominal cross section in service connections .

M&L brick protection cover to electric cable with sub class 'B' bricks laid dry and flat abutting each other with gap between adjascent not exceeding 10mm.

Gayatri Associates (BID ID -3384800)