CERTAIN REPAIR TO FLOORING BRICK WORK ROOF SUNKEN TREATMENT ROOF TREATMENT FLOORING ROOFING SANITARY AND PLUMBING WORKS IN OTM ACCN IN 6 MTN DOU OFFICE COMPLEX OF GE E BLY AOI STN GYM SWIMMING POOL AND P 68 OTM MD ACCN OF 883 AT ASC BN AND

Amount

Taking down cement plaster including racking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed by Engineer - in - Charge.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer - in - Charge.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons Laid, bedded and pointed in any mortar etc complete all as specified and directed by Engineer - in - Charge..

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15 cm thickness below or above ground level complete all as specified and directed by Engineer-in-Charge.

Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed by Engineer-in-Charge.

Demolition of concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed by Engineer-in-Charge.

Taking down chowkats or frames not exceeding 1.5 Sqm each with shutter (without taking off shutter from the frame) complete all as specified and directed by Engineer-in-Charge.

Taking down chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each with shutter (without taking off shutter from the frame) complete all as specified and directed by Engineer-in-Charge.

Taking down shutter of any description exc. 1 sqm but n.exc 2 sqm each and removing from site complete all as specified and directed by Engineer-in-Charge.

Dismantling of 100mm bore cast iron/ pvc drain pipe alongwith fittings and accessories jointed in cement mortar and taking out from walls, floors or from trenches, if required complete all as specified and directed.

Dismantling of 75mm bore cast iron / pvc drain pipe alongwith fittings and accessories jointed in cement mortar and taking out from walls, floors or from trenches, if required complete all as specified and directed .

Taking up or down15 mm steel tubing and connections including cleaning for refixing or removal complete all as specified and directed by Engr-in-Charge

Taking up or down 20 mm steel tubing and connections including cleaning for refixing or removal complete all as specified and directed by Engr-in-Charge

Dismantling water tanks 500 ltr & n exc 1000 ltr and removing to store of all retrieved material complete all as specified and directed by Engr-in-Charge

Dismantling asbestos cement (corrugated, semi corrugated etc) sheets in roof coverings including ridge etc complete all as specified and directed.

Dismantling timber scantlings 40 Sqcm and over in section, in any position , framed work complete all as specified and directed.

M&L for second class hard wood (SAL) in scantling, clean sawn, timber framed work complete all as specified and directed.

S & F for 6 mm thick Asbestos cement, (corrugated or semi corrugated) sheets in roofs, walls, fixed with L-type or J-type hook or cranked bolts complete all as specified and directed.

S&F for 6mm thick Asbestos cement two piece adjustable serreted ridge for corrugated , semi-corrugated etc sheets fixed with L-type or J-type hook or cranked bolts complete all as specified and directed.

M&L 15mm thick rendering in cement mortar 1:4 to brick masonry wall surfaces or on other than fair faces of brick wall surfaces finished fair & even without using extra cement for fixing tiles etc complete all as specified and directed

M & L 25 mm thick PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in floors, surfaces finished fair and even complete all as specified and directed.

M&L screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:6, for laying floor finishes/tiles complete all as specified and directed.

M&L screed bed or bedding layer of mortar, 20 mm thick, in cement mortar 1:6, for laying floor finishes/tiles complete all as specified and directed.

M&L Non- skid coloured ceramic tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile complete all as specified and directed.

M & L 9 to 10 mm thick glazed coloured ceramic tiles ( square/ rectangular) with border , area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in vertical surfaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles complete all as specified and directed.

M&L for Glazed ceramic coloured tiles in verticle surface of size 300 mm x 200 mm x 7mm thick, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and directed.

M&L for solid PVC interlocking luxury performance floor tiles fixed with suitable fixing arrangement incl preparing floor levelling complete all as spd and directed. Make :- Action tessa,Pergo,Welpsun or equivalent as appoved by GE

M&L for vitrified coloured tiles 10 mm thick (Square/rectangular) polished area of each tile not exceeding 0.37 sqm on floor set and jointed in neat cement mortar and pointed in white or coloured cement to match the shade of tiles complete all as specified and directed.

M&L for vitrified coloured tiles 10 mm thick (Square/rectangular) polished area of each tile not exceeding 0.37 sqm in vertical surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and directed.

M&L for vitrified glazed ceramic coloured / double charged / ultra charged tiles 10 mm thick square/ rectangular) polished area of each tile exceeding 0.36 sqm but not exceeding 0.42 sqm in floors etc. set and jointed in neat cement slurry and pointed in matching colour 5 mm thick epoxy filling in between tiling complete all as spd

M&L for vitrified glazed ceramic coloured / double charged / ultra charged tiles 10 mm thick square/ rectangular) polished area of each tile exceeding 0.36 sqm but not exceeding 0.42 sqm as in vertical surfaces such as skirting or dado set & jointed in pointed in matching colour 5 mm thick epoxy filling in between tiling complete all as specified and directed.

M&L Machine cut kota stone slab flooring 20-22 mm thick and size exc 0.16 sqm jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing the surface complete all as specified and directed

M&L Machine cut kota stone slab 20-22 mm thick as in riser and steps, skirting in full length in single piece of stair width laid over cement screed and jointed with rubbing and treating the surface incl full round bull nosing edging complete complete all as specified and directed.

M&L 20-22 mm thick Granite of any colour (table rubbed and polished) as in windows cill , in steps, jambs, pillars, window cills,cooking platforms and like in cement mortar (1:4) including form work , pointing in white cment (1:2) using marble dust with admixture of pigment to match with shade of granite with full round bull nosing edging complete all as spd as directed

M & L for 15-16 mm thick italian marble/ composite marble on floor surface jointed with grey cement slurry mixed with pigment to match the shade of the surface complete all as specified and directed

M& L for preparation of newly plastered wall surfaces and appltying three coats of texture (Domasc/Rustic) finished painting with the following process the surfaces should be completely dry and free from loose particles including preparing the surface with emry paper 180 nos and wipring clean and applying one coat of primer and allow drying for 6 to 8 hours then smoothen the surface by filling dints with thin coat of acrylie wall putty after drying for 4 to 6 hours and preparing the surface with emry paper and clean and applying another coat of primer and allow drying for 6 to 8 hours and then emulsion 1 Ltr with 500 ml water and applying with brush follwed by rolling with sponge roller or filter roller, applying three coat with brush and roller with and interval of 3 to 4 hours between successive coat all as per manufactures instruction complete all as specified and directed

M& L for preparation of newly plasted wall surfaces and applying three coats of texture (Super fine) finished painting with the following process the surfaces should be completely dry and free from loose particles including preparing the surface with emry paper 180 nos and wipring clean and applying one coat of primer and allow drying for 6 to 8 hours then smoothen the surface by filling dints with thin coat of acrylie wall putty after drying for 4 to 6 hours and preparing the surface with emry paper and clean and applying another coat of primer and allow drying for 6 to 8 hours and then emulsion 1 Ltr with 500 ml water and applying with brush follwed by rolling with sponge roller or filter roller, applying three coat with brush and roller with and interval of 3 to 4 hours between successive coat all as per manufactures instruction complete all as specified and directed

M & L for 75mm thick PCC 1:3:6 , type C-2 (using 40 mm graded crushed stone aggregate) as in plinth protection laid in slope in 1:30 in alternative bays not exceeding 3 mtr in length. Exposed surfaces finished even and smooth without using extra cement including raking out joints between panel to panel and panel to wall and plugging the same with bitumen mastic using bitumen and sand mixture in 1:3 complete all as specified and directed .

M& L 100 mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base floor / pavings complete all as specified and directed

M&L Sand filling under floors or in foundation including watering and consolidation complete all as specified and directed

M&L for Machine pressed cement concrete factory made coloured interlocking paver block any shape and size confirming to IS 15658 -2006 of 80mm thickness, M-40 Grade, machine pressed of pattern and colour as approved by GE complete all as specified and directed.(Make : M/s Mayur tiles , M/s Jain tiles industries or equivalent as approved by GE)

M&L for PCC (1:2:4) type B1 using 20mm graded crushed stone aggregate) for machine pressesd precast cement concrete kerb stone of size 300 mm x150 mm x 450mm, including weathering, slightly rounded or chemferred angles and throating , as directed edges complete including excavavtion for kerb stone as directed.

M&L for brick work with fly ash bricks, straight or curved on plan exc. 6 m mean radius, built in CM (1:6) complete all as spd as directed

M&L rendering 15 mm thick in CM 1:6 on brick masonary wall surfaces or on other than fair faces of brick masonry and finished even and smooth witout using extra cement complete all as specified and directed.

M& L for rendering 15mm thick in cement mortar (1:4),finished even and smooth using extra cement to on brick masonary wall surfaces or on other than fair faces of brick masonary finished even and smooth without using extra cement with using water proofing liquid @ 150 ml per bag of cement complete all as specified and directed.(Note : Water proofing liquid shall be measured and paid separately as "SUPPLY ONLY")

M&L rendering 5 mm thick in CM 1:3 as on concerete surface on ceilings finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M & L for applying cement slurry over existing roof surface @ 3 Kg/Sqm including mix with water proofing liquid @ 0.15 ltr per 50 kg cement bags as per manufactures instructions complete all as specified and directed.

M&L screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:4, laid over RCC roof slabs for laying water proofing treatment mixed with using water proofing liquid @ 150 ml per bag of cement complete all as specified and directed by Engineer-in-Charge.(Note : Water proofing liquid shall be measured and paid separately)

supply Integral water proofing Liquid of Dr fixit/sika/Fosroc complete all as specified and directed

M&L PCC 1:5:10 type E-2( using 40 mm graded crushed stone aggregate) as in sunken, sub base of floor fillings with broken brick aggregate complete all as specified and directed

S&F 32mm dia GI pipe, medium grade as in spout pipe in sunken floor complete all as specified and directed.

S & F in repair 2nd class hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints,complete all as specified and directed

S&F for 40 mm thick factory made flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed .

S&F 35mm thick factory made glazed and skeleton door shutters open rebated of second class hard wood rail and styles(Hollock), prepared to receive glass/gauge etc without sash bars, edges of framing plain cham-fered or rounded, mitred and rebated sash bars, any numbers The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed by Engineer-in-Charge. (Note :- S & F wire mess shall be measured and paid separately)

S & F 150 mm long floor door stopper of aluminium alloy body and tongue, brass body and tongue with hard drawn steel spring fixed in floor complete all as specified and directed

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm thick single side prelam PVC sheet used instead of Plain colour PVC sheet , suppling & fixing in opening as per specification & drawing complete all as specified and directed

S&F 30 mm thick factory made both side Prelam PVC sheet used instead of Plain colour PVC sheet. Stile and rails feathered at edges consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded palin colour PVC `C' channel heaving a Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S & FSolid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F 30 mm thick Factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded palin colour PVC `C' channel heaving a PVC sheert strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bbottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F mild steel window grills box type framed work as in window guard bars, grills or forged into spikes, framed balusters, walkway railing and similar work including welding complete FE-290 grade E-165 all as specified and directed.

S&F for steel windows/ventilators conforming to IS-1038 with side hung shutters including box type hinges with 2 Nos MS 100mm size tower bolt over MS flat iron for each openable leaf & Z section handle and steel peg stay complete without glazing bars, dovetailed or welded including one shop coat of Red Oxide Zinc chromate primer complete all as specified and directed by Engineer-in-Charge. (Note :- Wire cloth shall be measured and paid for separately).

S&F for steel windows conforming to IS-1038 with side hung shutters including box type hinges with 2 Nos MS 100mm size tower bolt over MS flat iron for each openable leaf & Z section handle and steel peg stay complete with glazing bars, dovetailed or welded including one shop coat of Red Oxide Zinc chromate primer complete all as specified and directed by Engineer-in-Charge. (Note :- Glass shall be measured and paid for separately).

S&F for steel ventilators fixed type, with glazing bars complete welded including one shop coat of Red Oxide Zinc chromate primer complete all as specified and directed by Engineer-in-Charge. (Note :- Glass shall be measured and paid for separately).

M&L for 3mm thick sheet glass ordinary quality and glazing with oil putty in squares not exc. 0.5 Sqm in each pane complete all specified and as directed.

Hacking out old, broken glass (any thickness,) size quality or description) from metal frames incl.punching or drilling out old glazing pins/spring clips and fixing new ones including M&L for 3mm thick sheet glass ordinary quality and glazing with oil putty in squares not exc. 0.5 Sqm in each pane complete all specified and as directed.

S&F stainless steel wire cloth, 0.56 mm nominal dia of wire and average with of aperture 1.18 mm and fixed with stainless steel wire staples complete all as specified and directed by Engineer-in-Charge.

S&F in repair stainless steel wire cloth, 0.56 mm nominal dia of wire and average with of aperture 1.18 mm and fixed with stainless steel wire staples in m s window / wooden shutter complete all as specified and directed

S&F aluminium alloy powder coated aluminium door frame fixed with side hung shutters and glazing fixed with and including 5.50 mm thick tinted glass fixed with rubber gasket with aluminium heading, clips frame made with aluminium box sec as appended below complete all as specified and directed (a) Frame 100x44x1.48mm thick with rawl plug (b) Middle and lock rail : 150x44x1.48mm thick (c) Bottom rail : 150x44x1.48mm thick (d) Top rail/style : 85x44x1.48mm thick (e) Aluminium beading : 0.7mm thick (f) Aluminium handle D type 150mm long, aluminium tower bolt 9.9mm dia shoot 200mm long brass mortise lock 100mm 4 leaver aluminium stopper, cleat double action floor spring hydraulically regulated made of n.less than 1.25mm thick aluminium alloy sheet foundation box main body with stainless steel cover governing pivot made of brass other part of steel heavy duty ( Make Sandhu ISI marked or its equivalent approved make) (g) Making good of wall surface to match with existing surface complete.

S&F aluminium alloy powder coated aluminium door frame fixed with side hung shutters and glazing fixed with and including 5 mm thick aluminium composite panel LDPE core PET coating ( both side decorative type ) fixed with rubber gasket with aluminium heading, clips frame made with aluminium box sec as appended below complete all as specified and directed (a) Frame 100x44x1.48mm thick with rawl plug (b) Middle and lock rail : 150x44x1.48mm thick (c) Bottom rail : 150x44x1.48mm thick (d) Top rail/style : 85x44x1.48mm thick (e) Aluminium beading : 0.7mm thick (f) Aluminium handle D type 150mm long, aluminium tower bolt 9.9mm dia shoot 200mm long brass mortise lock 100mm 4 leaver , with S S hinges complete (g) Making good of wall surface to match with existing surface complete.

S&F Powder coated aluminium sliding windows frame with movable shutter ( sliding on minimum two PVC roller of best quality, for each shutter on three tracks with stainless steel mosquito proofing and glazing shutter and incl 5.50 mm thick glass & stainless steel wire messs fixed with neoprene rubber gasket with aluminium beading, clips,frame made with aluminium section as appended below- (i) Window frame :68.4x38mm X 1.15 mm thick for three tracks. (ii) Top/bottom rail and style / rail of shutter : 15x37.5x1.15 mm thick and over. (iii) Aluminium beading - 0.7mm thick (iv) stainless steel wire cloth 0.45mm nominal dia of wire and average width of aperature 1.40mm and fixed in aluminium window or alongwith F/Y section fixed with aluminium wire staples complete. (v) Aluminium fittings such aluminium suitable handle with auto interlocking closing (vi) Making good of wall surfaces to match with existing surfaces complete all as specified and directed.

S&F Powder coated aluminium sliding windows and frame with movable shutter ( sliding on minimum two PVC roller of best quality on two tracks Aluminium composite panel shutter fixed with neoprene rubber gasket with aluminium beading, clips,frame made with aluminium section as appended below- (i) Window frame :45.2x35mm X 1.15 mm thick for two tracks. (ii) Top/bottom rail and style / rail of shutter : 15x37.5x1.15 mm thick and over. (iii) Aluminium beading - 0.7mm thick (iv) Aluminium fittings such as aluminium suitable fittings for auto interlocking closing (v) Making good of wall surfaces to match with existing surfaces complete all as specified and directed.

S&F Powder coated aluminium ventilators box type with louvers & wire mess neoprene rubber gasket with aluminium beading, clips,frame made with aluminium section as appended below- (i) Window frame :63x35mm X 1.48 mm thick for two tracks. (ii) Top/bottom rail and style / rail of shutter: 19x38x1.48mm thick and over. (iii) Aluminium beading - 0.7mm thick (iv) Aluminium neccessary fittings complete as required basis. (v) Making good of wall surfaces to match with existing surfaces complete all as specified and directed.

S & F for aluminium powder coated frame hollow sections members of size 63.50 mm x38mmx 1.48 mm thick,4 mm thick aluminium composite panel LDPE core with PET coating fixed with into the wall for kithen cabinet/ cupboard shelf incl hanging self for clothes with aluminium clip/strips, pvc beadings fixed with adhesive on edging , design as per site requirements basis, complete all neccessary fitting all as specified and directed

S & F partition wall of powder coated aluminium hollow sections members of size 63.50 mm x38mmx 1.48 mm thick with distance of vertical hollow section, 1.2mtr to 1.8 mtr height of wall having top rails ,bottom rails and middle rail of size 63.50 mm x38mm x 1.48 mm and upto middle rail wall panels shall be covered by 5 mm thick aluminium composite panel LDPE core PET coating ( both side decorative type )with aluminium clip height of middle rail shall be 1 meter from floor and remaining portion above middle rail shall be provided with 5 mm thick glass incl eaching approved designed with aluminium stiprs/beadings with rubber gasket as per existing or as provided compelte all as specified and directed

M & L powder coated aluminum window/ doors grills fixing along with frame of following specification, grills with opening 69.4mm X 78.2mm grills thickness shall be of 6.4mm X 5.8mm having weight not less than 2.306 Kg/per sqm shape as ordered with frame channel of 34 X 11mm X1.7mm thick fixed with screw inside of the window all as directed by Engr-in-Charge and all as specified and as directed.

M/L for repairing to existing aluminium doors of any size by straightening of frame / shutter, replacing the detoriated member with new, replacing the broken / non funcional hinges with new, replacing decayed rubber gasket with new, replacing the broken glass pane of any size with new 5.00mm thick tinted glass, replacing unserviceable handle, tower bolt, lock, floor spring, foundation box with governing pivot, top pivot, peg stay etc with new and including taking down and at same place after making the door / window smooth functional complete all as specified and directed.

M&L for E-board false ceiling consisting of powder coated GI wall angle, main T and cross T of 25mmX 25 mm X 1.40 mm thick grid frame work, joist, angle/ Tee as directed and mild steel wire hook not less than 6 mm dia with arrangement for adjusting height of ceiling and including provn of 4 mm thick E- Classic board in pannelof size 600X600mm with necessary off cut including dismantling of existing false ceiling and taking down and refixing of Electric fitting carefully complete all as specified and directed.

S&F in repair PVC hollow interlocking wall paneling of 5mm thick prelam PVC sheet. The panel & strips shall be of 600 kg / cbm density manufactured by an ISO-9000 certified company. The strips should two PVC strips. The PVC strip shall be fixed to the wall using 65mm long M.S screws through the groove in the strip by using PVC fasteners. The distance between two screws shall not be more than 200mm. The exact size of the panel and correspondingly of the grid may vary depending on the size of the wall. Optionally a strips of 5mm thick PVC sheet of width 75mm feathered at the edges shall be stuck at the places where two panels are joined, using solvent cement.

S&F in repair Venetian blind colouredstrip 75 mm top 5 mm thick powder coated aluminium rod rod ends at brackets are moulded type etc complete all as directed.

S&F 12 mm thick toughned glass door with powder coated aluminium frame including neccessary locking ,handle etc with double action floor spring in each shutter complete as requirement of site with suitable height and any type of eaching designed on tougned glass , off cuts complete with finishing wall in CM 1:4 , designed approved by Engr-in Charge complete all as specified and as directed.

S&F 12 mm thick toughned glass partion wall with or without powder coated aluminium frame with any type of eaching designed on tougned glass , off cuts complete as requirement of site with arrangement for suitable height with off cuts all as complete all specified and as directed.

M & L double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as spd and as directed

S& F in repair door closer hydraulically regulated Aluminium (extruded section body), designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed complete all as specified and as directed

S & F 300 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and as directed.

S & F 150 mm thick Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and as directed.

S&F 150mm size aluminium handles, cast type anodised completed all as specified and directed.

S&F 100 mm size butt hinges (medium weight) cold rolled mild steel complete all as specified and directed by Engineer-in-Charge.

S&F in repair 375mm, ordinary rat tail rod patttern springs includding roller and roller platewith fixed to wooden/pressed steel frame chowkats with flat iron 40x3mm size 75 cm long with necessary bolts, etc. complete

S&F 300 mm long mild steel sliding door bolts plate type stone enamelled black with bright bolt not less than 16 mm dia with and including a minimum of 6 bolts and nuts, 04 Nos on bolt plate and 02 Nos on staple plate and fix complete all as specified and directed

M&L for cleaning of RCC or PVC water tank at any height (on accessible / inaccessible of roofs) by removing all scale, dirt, mud etc. from tanks capacity exc 500 ltrs but not exc 1000 ltrs unpluging flushing out and cleaning proporly internally and externally with detergent powder complete, and again cleaning with fresh water including plugging back from mouths of circulating pipes etc. complete all as specified and directed

S&F 1000 litres, rotational moulded polyethylene of white colour in tripple layer water storage tank (cylindrical vertical with closed top with suitable size of M S Tasla with suitable locking system ), hoisted and fixed in position complete all as specified and directed

S&F 500 litres, rotational moulded polyethylene white colour in tripple layer water storage tank (cylindrical vertical with closed top with suitable size of M S Tasla with suitable locking system ), hoisted and fixed in position complete all as specified and directed .

S&F 20mm bore ball brass valve high pressure with polythene float and fly nut complete, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engineer-in-Charge.

S&F 15 mm dia steel water tubing galvanized medium grade concealed in all type wall with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed by Engineer-in-Charge

S&F 20 mm dia steel water tubing, galvanized, medium gradeconcealed in all type wall with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed

S&F in repairs, vitreous China wash hand basin, white, flat back size 550 x 400mm including 15mm dia pillar tap , 450 mm long HDPE PVC connection, 750 mm long 32mm bore HDPE waste down pipe including Stainless steel brackets all s directed. Make (cera or equivalent as approved by GE.)

S&F in repairs vitreous chinaware coloured wash hand basin with pedestal of size 55X45X82cm complete including fancy CP pillar tap, CP Waste coupling ,waste pipe ,complete fixing arrangement and cutting for and pinning in walls & making good complete all as specifed and directed by Eng in charge.Make :- cera /parryware or equivalent complete all as specified and directed by Engineer-in-Charge

S&F in Vitreous China table top wash basin of suitable size including SS bottle trap, HDPE waste pipe including fixing on counter with SS waste coupling complete all as specified. Model : Cat No 91072 Orchid of Hindware or equivalent model of Parryware, Cera or Jaquar as approved by GE.

S&F in repair fancy type brass chromium plated toilet paper holder, complete all as specified.Make Jaguar or equivalent as approved by GE.

S & F in repair fancy type 150mm size square brass CP shower rose all as specified.Make Jaguar / hindware/ cera or equivalent as approved by GE.

S&F in repairs 15 mm dia bib tap fancy type chromium plated with flange quarter turn complete all as specified as directed. Make Jaguar / hindware/ cera or equivalent as approved by GE.

S&F in repairs 15 mm dia bib tap cast copper alloy with butterfly handle , screwed down for iron pipe or for brass ferrule and fixed complete all as specified as directed. Make Cera or equivalent as approved by GE.

S&F in repair fancy type 15mm dia brass chromium plated mixer for mixing hot and cold water screwed down for iron pipe and fixed to WHB including taking out existing mixer from old WHB, complete all as specified. Make Make Jaguar / hindware/ cera or equivalent as approved by GE.

S&F in repair fancy type chromium plated brass two way bib cock suitable for 15mm bore pipe complete all as specified and directed. 2 Way Bib Cock with Wall Flange. Make Jaguar / hindware/ cera or equivalent as approved by GE.

S&F stainless steel of AE - SI 316 grade tubular towel ring including apair of CP brass bracket complete all as specified.Make Jaguar / hindware/ cera or equivalent as approved by GE.

S&F in repairs 15mm bore PVC connections, with PTMT nuts of length 450mm complete all as specified and directed.

S&F in repair fancy type brass chromium plated soap dish of 160x160x90 mm , complete all as specified.Make Jaguar or equivalent as approved by GE.

S&F in repair fancy type chromium plated brass angle valve type suitable for 15mm bore pipe complete all as specified.Make Jaguar or equivalent as approved by GE.

S&Fin repair fancy type stainless steel towel rack size 600mm X 300mm including apair of brass bracket complete all as specified &directed by Engr in charge. Make Jaguar or equivalent as approved by GE.

S&F chromium plated brass tubular towel rail 20 mm dia, D type for wash hand basin centre holed fixed to iron pipe complete all as specified and directed. Make Jaguar or equivalent as approved by GE.

S & F in repair fancy type sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with CP bracket gaurd and railling 60 cm long complete all as specified. Make Jaguar or equivalent

S&F in repair fancy type glass corner 300mm radius of 10mm thick toughned glass with CP railing fixed with screws fancy type complete all as specified .Make: Cardin or equivalent as approved by GE.

S&F in repairs of 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified

S&F in repair 15 mm dia fancy type stop cock , chromium plated with long shank and cup (conncelaed type) for iron pipe or for unions and fixed complete all as specified

S & F in repairs Rimless Single piece-WC with UF soft close seat cover, Hinges, Fixing Accessories, Accessories Set and Cistern fittings,Size: 360x675x750 mm, S Trap-300 mm make Jaguar or equivalent including making good to floor complete all as specified and directed.

S&F in repair vitreous china squatting pan of orrissa pattern long pan size 580 x 440 mm white with "P"or "S" trap size 100 mm dia front or back inlet and integral foot rest any pattern (excluding flushing cistern and flush pipe) including provn of lime concrete bedding complete all as specified. Make Hindware / parryware or equivalent as approved by GE.)

S&F in repair vitreous China coloured European type WC with "P" or "S" trap white including connection to drain or out going pipe and to flushing pipe, antisyphonage pipe etcplastic water seat white/black pattern flat bottom and cover and mild stel chroumium plated. complete all as specified.(Make:- Hindware / parryware or equivalent as approved by GE.)

S&F in repairs, PVC low level flushing cistern 10 litres capacity, valve less, symphonic action type with float, handle including 32mm dia PVC flush pipe of polyethylene of low or high density & bracket etc complete all as specified and directed .(Make:- Hindware / parryware or equivalent as approved by GE.)

S & F Brass CP health faucet with 8mm Dia 1.2 Meter Long Flexible Tube and Wall Hook screwecd for iron pipe fancy type long body all as specified and directed. (Make:- Jaguar or equivalent as approved by GE)

S & F Brass CP Hand Shower with 8mm Dia 1.2 Meter Long Flexible Tube and Wall Hook screwecd for iron pipe fancy type long body all as specified and directed. (Make:- Jaguar / hindware/ cera or equivalent as approved by GE)

S&F in repair swimming pool over flow grating made from high grade fabricated plastic / ABS with a design which allows easy seepage of water into with anti slip surface used to cover the overflow channel around the swimming pool of any required size complete all as specified and directed.

S&F in repairs, vitreous China bowl urinal flat back of size 430 x 370 x 340 with grating and union for discharge pipe excluding flushing cistern flush pipe and waste pipe complete all as specified and directed.

S&F in repairs, wall mounted urinal size 370x315x620 with all fixing accessories complete all as specified and directed.Make:- Jaquar model :- URS WHT 132530 or hindware/ cera as approved by GE.

S&F in repair PVC (SWR) multifloor trap with grating including jointing with solvent cement floor trap 75 mm dia outlet plain with grating including jointing to waste pipe fixed in cement concrete 1:2:4, type B-1 complete all as specified and directed.

S&F in repair PVC (SWR) 75 mm bore pipes single socketed in any length with rubber ring joints fixed to wall and floor with necessary fitting complete all as specified and directed by Engr-in-charge.

S&F in repair PVC (SWR) 110 mm bore pipes single socketed in any length with rubber ring joints fixed to wall and floor with necessary fitting complete all as specified and directed.

S&F PVC (SWR) 110mm bore bends any radius complete all as specified and directed.

S&F PVC (SWR) 75mm bore bends any radius complete all as specified and directed.

S&F PVC (SWR) 75 mm bore junction single (Single 'T') equal or unequal with access door complete all as specified and directed.

S&F PVC (SWR) 110 mm bore junction single (Single 'T') equal or unequal with access door complete all as specified and directed.

S & F in repair PTMT alloy toilet cabinet with mirror of overall size 350 x 450mm and fixed to wall complete all as specified and directed. (Cat Part No. 551 of Make Prayag or equivalent as approvd by GE.

S & F in repair sinks made of stainless steel 1.0-1.2 mm thick kitchen with plugs, washers and wastes; including bedding in cement mortar onbowl type overall size 23" L x 18"W undermount kitchen Sink with basket Strainer complete all as specified and as directed .

S&F in repair 20 mm dia stainless steel 1.0 mm thick fancy type SS curtain rods with decorative design matching brackets as approved and knobs (lattu) or end bracket as required & other all neccesary fittings fitted with SS screws etc on each end complete all as specified and as directed.

M&L for providing & injecting chemical for post construction ATT along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc in a portion with cement mortar 1:2 to match the existing apron complete all as specified and directed.

M & L for Post Construction anti termiteTreatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same as specified and directed.

M & L for Post Construction anti termiteTreatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floor soil complete as specified and directed.

S & F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete as specified and directed

S&F Pre-coated galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws as specified complete as specified and directed

S&F 0.80 mm plain galvanised Mild steel sheeting in ridge, hips, valley gutter,drip and straight flashing class8 with zink coating @ 120 gms /sqm fixed with L- type or J- type or cranked hooks bolts complete all as specified and directed.

M & L for cutting chases of hanging chajjas, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of sunshades, shelves, lintels, Chajja ( up to IInd floor) etc making good, cutting out exc 10cm and not exc 40cm girth in RCC chajjas in brick walls complete all as specified and as directed.

Dismantling of concrete by chiseling from RCC members like column , beam, parapet facia, chajja, ceiling,etc exposingthe reinforcement without disturbing the reinforcement free from rust by sand blasting/using chemical , apply a coat of rustolin to remove rust and acralic polymer on old rusted reinforcement proving at places addl reinforcement welding with existing reinforcement as directed wherever required binding RCC 50 mmx50 mm (10 mm gauge welded mesh ) & tack , securing with clips / blinding wire, welding & provision guniting pressure 2.2 to 2.5 kg /sqm with admixer 1 cement 3.5 of sand of thickness 25 to 40 mm including stripping floating with wooden strippers for proper dimension control neccssary form work & scaffolding up to three storey and including height of head room complete surface of guniting to be finished fair with 10 mm thick plaster in cement mortar 1:4 with water proofing compound @3% by weight of cement and recron 3 S as per manufacturer instruction cleaning & removing of waste meterial etc as dirply two coat of Dr fixit /pidilite new coat ezee at interval of 8 hours cure for the surfaces complete all as specified and as directed

S&F for 0.71mm thick Aluminium plain sheeting Alloy 31000 H4, STUCCO Embossed finish with fixed with coach screw and Aluminium washer in roof and wall etc. with end laps stitched with 25x6mm G.I. bolts at 20cm apart incl dismantled also all as spd as directed

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doo0rs etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and fastening and fixing FE 290 Gde E-165 complete all as spd as directed

S & F 1.25 mm thick Mild steel, plain black sheet in steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up, mitred angles etc as required complete including cutting out of existing sheet if required all as spd as directed

M&L preparation new or previously untreated steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide zinc chrome primer complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new or previously untreated wooden or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over and including one coat of pink primer complete all as specified and directed by Engineer-in-Charge.

M&L for complete removal of existing treatment on walls etc including cleaning of any mortar drops, fungus, efflorescent salts etc and preparation of old plastered surfaces and applying two coats of oil bound distemper over 1mm thick cement based in double layer wall care putty complete all as specified and directed.

M&L for preparing newly plastered walls surfaces and applying two coats of oil bound distemper over 1mm thick wall care putty complete all as specified and directed.

M&L for complete removal of existing treatment on ceiling, etc including cleaning of any mortar drops, fungus efflorescent salts etc and preparation of old plastered surfaces and applying two coats of oil bound distemper over and including one coat of 1mm thick double coat wall care putty complete all as specified and directed.

M&L for preparing newly plastered walls surfaces and applying two coats of cement base paint over a coat over 1mm thick cement based wall care putty complete all as specified and directed.

M&L for preparing newly plastered surfaces and applying three coats of white wash on ceiling complete all as specified and directed.

M&L for complete removal of existing treatment on ceiling, etc including cleaning of any mortar drops, fungus efflorescent salts etc and preparation of old plastered surfaces and applying two coats of white wash complete all as specified and directed.

UTTRAKHAND BUILDERS

M/S R S Constructions

j u enterprises

TRISHOOL ASSOCIATE