CERTAIN REPAIR TO ROOF LEAKAGE SEEPAGE TO WALLS SUNKEN FLOORS CEILING TOILETS AND MISC B AND R REPAIRS TO OTM ACCN AT PALAMPUR MIL STN

Amount

Dismantling of old rusted plain or corrugated steel sheeting, any gauge, thickness,including Nainital or similar pattern roof covering etc. complete all as specified and as directed.

S&F 0.63mm Galvanised,corrugated mild steel sheeting with two corrugations side lap,fixed with L-type or J-type or cranked hook bolts and washers in roofs,walls etc. with grade of zinc coating 275 complete all as specified and directed.

All as per Srl item No. 02 above but except sheeting.

S&F 0.80 mm in thickness plain, galvanised, mild steel sheeting, in ridges, hips valley gutters,drip and straight flashings ( length and girth as fixed) with grade of zinc coating 275 complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified, compete all as specified and directed. (Colour as approved by GE)

M&L pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, facia and fixed with self tapping screws as specified. (Colour as approved by GE)

Dismantling wrought iron or mild steel work of any description not other wise provided for complete all as specified and directed.

S&F mild steel roof trusses (framed), trussed, purlins, crane gantries. rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, Fe 410-W (Grade E-250) complete all as specified and directed.

S&F rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guidese for sliding doors; fixed with angle cleats or other connecting plates and similar work confirming to grade Fe 410-W (Gde-E-250 quality A) complete all as specified and directed.

Dismantling of wall & ceiling boards (fiber, pulp, insulation etc) or insulation boards /slabs /blankets any thickness, including cover fillets complete all as specified and directed.

Providing and fixing tiled false ceiling of size 595x595mm in true horizontal level suspended on interlocking gypric metal grid of hot dipped galvanized steel section (galvanized @ 120 gms/sqm, both side inclusive) consisting of 3600mm long main "T" runner size 24x38mm and 0.30mm thick, 1200mm long cross "T" of size 24x25mm and 0.30mm thick, 600mm secondary cross "T" of size 24x25mm and 0.30mm thick and PPGI wall angle of size 24x24mm and 0.4mm thick, bottom exposed capping of width 24mm of all T-sections shall be of 0.25mm thick PPGI, wall angle is fixed along the perimeters of the ceiling to walls, partitions or columns etc with rawl plugs and wooden screws at 300mm centers Main "T" runners are then suspended from ceiling using GI slotted cleats of size 27x37x25x1.6m fixed to ceiling with 8mm dia and 45mm long dashfasterners, 4mm GI adjustable rods with galvanised butterfly level clips of size 85x30x0.8mm spaced at max 1200mm center to center along main T and not more than 150mm from spliced joints. The last hanger at the end of each main runner should not be greater than 600mm from the adjacent = wall, then 1200mm long cross "T" is interlocked between the main "T" at 600mm center to center to form a grid of 1200x600mm and then secondary cross "T" of length 600mm is then interlocked at middle of the 1200x600mm grid to form grids of 600x600mm. Cross tees at the ends having length more than 600mm are to be supported independently. Finally whitecoloured Gyproc 9mm thick Dew Drop/Granular tiles of size 595x595 having foil on back side & PVC paper on front side wrapped around edges to be placed in grid complete all as specified and directed.

Dismantling timber scantlings 40 sqcm and over in section in any position framed or unframed work etc, complete all as specified and directed.

M&L Second class hard wood timber in scantlings, clean sawn, fixed complete as specified and directed.

M&L Second class hard wood timber scantlings wrought fixed for unframed work for verandah post complete all as specified and directed.

M&L Second class hard wood timber scantlings wrought fixed for framed work complete all as specified and directed.

M&L preparing surfaces of wood and wood based materials, new or old of any description and girth, not otherwise described and treated with two coats of creosote tec. complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) n.exc. 1.50 sqm each complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.50 sqm but n.exc. 4 sqm each complete all as specified and directed.

Taking down shutters of any description exc 1sqm but n. exc 2 sqm each complete all as specified and directed.

Fabricate and fix in position anodised aluminium powder coated (minimum thickness of powder coating 50 micron of approved colour) door shutter with frame, partly glazed with 5mm thick tinted glass and partly panelled with 12mm thick prelaminated particle board with both side decorative laminated including rubber bead joining cleat for fixing in position, aluminium door handle 150mm size, aluminium barrel tower bolt 200mm size including hydraulic door closer complete all as specified and directed. Note:- (a) Frame (top & side) section shall be of size 101.60x44.75x2.4mm (section No. 14021) (b) Vertical members of shutter section shall be of size 85x44.45x2mm (section No. 19560) (c) Top members of shutter section shall be size 83.50x44.45x2.00mm (section No. 19581) (d) Lock rail (middle member) of shutter section shall be of size 150x44.45x3mm (section No. 19596) (e) Bottom members of shutter section shall be of size 150x44.45x3mm (section No. 19584) (f) Glazing clip for securing glass of shutters shall be of 0.80mm thick (section No. 19370) (g) Section No given above are of make Jindal, contractor may use similar sectoin of other make mention in Appx 'C'

S&F Powder coated Anodised aluminium window and ventilator shutters (minmium thickness of powder coating 50 micron), weight of aluminium section not less than 0.914 kg/m for style and rail, weight of glazing clip not less than 0.124 Kg/m including necessary joining cleats, glazing clips, rubber neoprane packing,anodised aluminium snap beading,screws,anodised aluminium fittings such as peg stays one number,hinges type B-21, 100 mm long two numbers,suitable handle one number on each shutter complete all as specified and directed.

S&F powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (fixed portions) with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beadaing for glazing/paneling, C.P brass/stainless steel screws, complete all as specified and directed.

M&L 2nd class hard wood, plain solid,straight chowkats and frames wrought framed rebated on the solid rounded or chamfered put to gether with glue pinned at joints as specified and directed.

S&F 35mm thick factory made 2nd class hard wood rail and style plain framed, panelled shutter with lock rail and panel of 9mm B.W.P commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and style as per IS:1003 (part 1) kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F 35mm thick, 2nd class hard wood, factory made, glazed & skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. Sizes of members of shutters as specified in SSR Part I, Section 8, Clause 8.24 (a) complete all as specified and directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgen polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 Kg/Cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of class A category with property of being termite /borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed.

M&L preparation of new wooden surfaces of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed.

S&F, solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube, supplying and fixing in opening as per specifications & directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat molded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement complete all as specified & directed.

S&F 18/19mm thick prelaminated particle board/ MDF board exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete as directed by Engineer-in-charge.

S&F mild steel continuous piano hinges, bright finish or electro galvanised, width of flap when open 30mm, complete all as specified and directed.

S&F 100 mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.

S&F 200 mm size (length of bolt) aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F 150 mm size (length of bolt) aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F 100 mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 125 mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 100mm size, hasp and staple safety type brass with mild steel hinge pin including bolt to hinge plate and fixed with screws all as directed.

S&F 250 mm size (length of bolt) aluminium alloy, anodised, sliding door bolt with hasp and staple ,(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F rolled mild steel bands,straps,supports or stays for rainwater,ventilating pipes,including bolts,if required; hooks(stays),heavy,for large gates,hook and pintle hinges;large hasps and staples;chains;hand made sliding bolts;clamps;hold fasts;wall ties;hooks for hanging fans;plain angle cleats for securing purlines to wooder trusses conform to Fe-290 Gde E-165 complete all as specified & directed.

M&L plain cement concrete 1:2:4 type B0 (using 12.50 mm graded crushed stone aggregate) cast in situ in lintels up to 1.5 m clear span, cills steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones(fixing hold fasts), bed plates, water through and the like including weathering, slightly rounded or chamfered angles and throating including use of form work (straight or curved) complete all as specified & directed.

S&F steel window 1.25mm thick box type (Primer coated) ERW hollow P section of size 60mm x 25m double rebated comprises guaged, glazed skelton shutter ERW sec 50mm x 20mm of 1mm thick with two openable leaf consisting two Nos sash bar of T-Section 20mm x 3mm complete wleded to frame with one vertical mullion of ERW box type T-section of size 30mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC M-15, type B-0 (04 Nos of each window, steel duly painted with one shop coat of zinc chromate primer on prepared surfaces) and finishing the surfaces to match with existing including following fitting welded to frame shutter:- (i) Hold fast, 150mm long of 12mm x 3mm made to shape- 04 Nos per window. (ii) Handle of Z section 20mm x 25mm, 100mm long- 1 No per leaf. (iii) MS tower bolt 150mm long- 2 Nos per leaf (iv) Z section 20mm x 25mm, 100 long stopper- 1 No per leaf. (v) Cleat 65mm long of hollow square 15mm x 20mm x 63mm welded to hinge- 1 No per leaf. (vi) Mild steel pintle hinge of size 75mm x 12mm- 2 Nos per leaf. (vii) Flat iron fillets of size 20x3mm for fixing wire gauge. (viii) Fabrication & fixing arrangement as per Drg No. CEPZ/TD 26/13.

S&F chimney bars (straight or camber); bearing bars; tongues or water bars for window frames; window guard bars, plain, let in and fixed independently in wooden frames, L or T section supports for shelves etc. and similar articles conforming to Fe-290 Gde E-165 complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised wire staples, complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised wire staples, fixed in repair, complete all as specified and directed.

M&L for plain fillets, square rectangular or triangular in section, wrought, bull nosed, splayed, chamfered or rounded on one edge or face, secured with nails or brad, 2nd class soft wood (kail) sec area exc 3 sqcm but not exc 6 sqcm as in cover fillets, complete all as specified and directed.

S&F well seasoned 2nd class hard wood small fitting such as cleats, brackets of any type,latch and hinge blocks,shaped door and windew stops and the like including all necessary labours articles n.exc 200 Cu.cm each complete all as specified and as directed

S&F 140mm long floor door stopper of aluminium alloy body and tongue,anodised, with hard drawn steel spring complete all as specified and directed.

S&F MS prepainted sheet type door spring heavy duty, 200mm long incl roller and roller plate complete all as specified and directed.

Hacking out old broken glasses (any thickness, size, quality or description) from wooden frames or steel frames, glazed with putty or fixed with wooden beads, complete all as specified.

S&F 3mm thick transparent fibre glass ordinary quality as in glazing not exc 0.50 Sqm in each pane fixed in wood or steel frames with oil putty or woof beads or self tapping screw complete all as specified and directed.

S&F 4.80mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc. 0.5 sq.m in each pane complete all as specified and as directed.

S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc. 0.5 sq.m in each pane complete all as specified and as directed.

S&F 3mm thick figured glass, pin head type and glazing with oil putty in squares n.exc. 0.50 sq.m in each pane, complete all as specified and directed.

Preparation of new steel surfaces of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide or zinc chrome primer, complete all as specified and directed.

Demolition of brickwork or stone/boulder masonry built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facing, dressed stone work precast concrete articles complete all as specified and directed.

M&L walling of random rubble, un-courses, with best quality locally available harder stones such as granite, trap, basalt stone etc, well bonded bedded & solidly hearted built in cement mortar 1:6, complete all as specified and directed.

All as per item No. 56 above but except stone. Note: Old stone obtained against dismantling/demolition shall be used.

M&L Brick work with sub class 'B' bricks, straight or curved on plan, to any radius, in half brick thick wall, using old size brick, built in cement mortar 1:4, complete all as specified and directed.

M&L plain cement concerete 1:2:4 type B-1, using 20mm graded crushed stone aggregate as in roof kerbs, mud stops, rounded or chamfered on edges, complete all as specified and directed.

M&L formwork to edges of concrete flats, breaks in floors, openings in concrete walls, floors and roofs and sides of RCC/PCC bans in walls, horizontal or sloping and similar work all exceeding 20cm wide (where RCC/PCC band in walls, spanning and opening, the formwork soffit only shall be paid for under item 7010)

Taking down cement plaster of any description on brick or stone or cement concrete block walls etc including raking out joints, hacking for key, scrubbing down with water etc, and removal of rubbish off the premises and leave the work clear of any plastering complete all as specified and directed.

M&L rendering 15mm thick plaster in cement mortar(1:4) on fair faces of brick work or concete surfaces, finished even and smooth without suing extra cement complete all as specified and directed.

M&L rendering 5mm thick plaster in cement mortar(1:3) on fair faces of RCC concrete surfaces and including applying cement slurry on bottom of slab, chajjas, facias etc complete all as specified and directed.

M&L 15mm thick rendering on fair faces of brick/concrete surface of wall in CM 1:4 to be finished even and smooth without using extra cement under roof treatment mixed with water proofing compound as per manufacturer's instructions complete all as specififed and directed. Note: WPC compound shall be measured and paid seperately.

M&L rendering 15mm thick plaster in cement mortar(1:6) on stone masonry wall surfaces or surfaces other than fair faces of brick work or one side of lathing, finished even and smooth without suing extra cement complete all as specified and directed.

M&L preparation of newly plastered surface of walls and applying two coats of oil bound distemper over 2mm wall putty to achieve smooth surface complete all as specified and directed.

M&L preparation of newly plastered surface of ceiling and applying three coats of white wash complete all as specified and directed.

M&L preparation of newly plastered surface of walls and applying two coats of cement base paint over a cost of primer complete all as specified and directed.

Supply only approved integral water proofing compound.

Demolition of cement concrete unreinforced in ground floors, kota stone, granite flooring, tiles flooring and paving's not exceeding 15cm thickness (below or above ground level) and removal unserviceable materials, debris and rubbish to a distance not exceeding 100m complete all as specified & directed.

Dismantling of stone slabs,paver blocks and tiles of any description or thickness in floors,path apron etc laid dry or laid dry and pointed surface complete all as specified and directed.

M&L 14 to 16mm thick green marble slab for kitchen platform/shelf and vertical faces duly machine cut in skirting/dado laid over cement screed and jointed with grey cmeent slurry including cutting and polishing of type including 15mm thick screed bed layerr in CM 1:6 complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L Non-skid, coloured ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exc 0.06 sqm but not exc 0.11 sqm as in floors etc laid over and including 15mm thick screed bed or bedding layer in cement mortar 1:6, set and jointed in neat cement slurry and pointed with white or coloured cement to match the colour of tiles complete all as specified and directed.

M&L Non-skid, coloured ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exc 0.18 sqm but not exc 0.38 sqm as in floors etc laid over and including 15mm thick screed bed or bedding layer in cement mortar 1:6, set and jointed in neat cement slurry and pointed with white or coloured cement to match the colour of tiles complete all as specified and directed.

M&L Glazed ceramic coloured tiles in vertical surface 350mm x 250mm x 7mm/450mm x 350mm x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match as in skirting/dado etc. laid over and including 10mm thick backing coat in cement mortar 1:4, set and jointed in neat cement slurry and pointed with coloured to match the tiles complete all as specified and directed.

M&L PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in mass concrete complete all as specified and directed.

M&L machine cut kota stone slab flooring 14 to 16mm thick laid over cement screed base and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (mirror face) complete over and including 20 mm thick screed in CM (1:4) complete all as specified and directed.

M&L machine cut kota stone slab 14 to 16mm thick in riser of steps,skirting,dado and pillar laid over cement screed base and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (mirror face) complete over and including 10 mm thick backing coat in CM (1:4) complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for, complete all as specified and directed.

M&L RCC 1:2:4 type B1 (using 20mm thick crushed stone aggregate) as in slab supported to walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

S&F mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Taking up or down 15mm bore steel water tubing and connections including cleaning for re-fixing, complete all as specified and directed.

S&F steel water tubing, 15mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specifed

Refixing old GI tubing 15mm bore medium grade galvanised tubes and connections in new or old position (walls, ceiling, floor etc) complete all as specified and directed.

Taking up or down 20mm bore steel water tubing and connections including cleaning for re-fixing, complete all as specified and directed.

S&F steel water tubing, 20mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specifed

Refixing old GI tubing 20mm bore medium grade galvanised tubes and connections in new or old position (walls, ceiling, floor etc) complete all as specified and directed.

M&L cutting chases, pinning in making good to facings hwere required and pointing in CM 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc. and cutting chases for ceoncealed water tubing or concealed conduit wiring etc. and making good, cutting not exc 10cm girth complete all as specified and directed.

S&F in repairs sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, inlcuding bedding in cement mortar on to dward wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F in repairs vitreous china, wash basin flat back, with pedestal white of size 550mm x 400mm including brass Chromium Plated waste coupling 32mm size with long screwed shank and fly nuts, flange end bedded in red lead cement,PVC medium grade 32mm size waste pipe, PVC connection 15mm size, 450mm long with PTMT nuts at both ends (fixed in repair), complete all as specified and directed.

S&F in repairs vitreous china, wash basin white oval type of size 550mm x 400mm including brass Chromium Plated waste coupling 32mm size with long screwed shank and fly nuts, flange end bedded in red lead cement,PVC medium grade 32mm size waste pipe, PVC connection 15mm size, 450mm long with PTMT nuts at both ends (fixed in repair), complete all as specified and directed.

Supply only pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for 15 mm bore iron pipe complete all as specified & directed.

S&F in repairs stop valve/angle valve, cast copper alloy, fancy type,chromium plated, screwed down, high pressure, with crutch or butter fly handle, screwed both ends for 15 mm bore iron pipe or for union complete all as specified & directed.

S&F in repairs stop cock, fancy type, chromium plated, with long shank and cup (concealed type) cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, screwed both ends for 15 mm bore iron pipe or for union complete all as specified & directed.

S&F in repairs, fancy type, chromium plated, bib tap, cast copper alloy with crutch or butterfly handle, screwed down, screwed for 15 mm bore iron pipe or for brass ferrule complete all as specified & directed.

S&F in repair vitreous china coloured wash down water closet pan (Padestal Pattern), including connection to flush pipe, 'P' or 'S' trap, with fixing bolts PVC seat cover with chromium plated mild steel hinges device (excluding flushing cistern and flush pipe), complete all as specified and directed.

Supply only plastic water closet seat, black or white closed pattern with flat bottom, cover and mild steel chromium plated hinging device complete all as specified and directed.

S&F in repairs vitreous china premium/1st quality wash down water closet hung EWC white/ivory/gel gasket etc. including fixing of pastic water closet seat cover, block/white closed pattern with flat botom and cover and mild steel chromium plated hinging device, flushing cistern (excluding flushing cistern & flush pipe) complete all as specified and directed.

S&F vitreous china squatting pan water closet, orissa pattern, size 580mm x 440mm white with integral foot rests (excluding flushing cistern and flush pipe) including PVC (SWR) 'S' trap,setting trap and pan in lime concrete and jointing to flush pipe (fixed in repair) and making good disturbed surfaces of floor and match with existing follor, complete all as specified and directed.

Supply only 10 litres capacity PVC valve less symphonic action type flushing cistern (ISI Marked) low level with inlet ball valve, float and handle including brackets & 32 mm size PVC flush pipe, complete all as specified and directed.

S&F in repairs 10 litres capacity PVC valve less symphonic action type flushing cistern (ISI Marked) low level with inlet ball valve, float and handle including brackets & 32 mm size PVC flush pipe, complete all as specified and directed.

S&F in repairs vitreous china bowl urinal flat back, size 465x355x265mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and directed.

S&F in repairs PVC coated mild steel conduit pipe 25mm dia (Drapery rod) with PVC coated MS clamps to hold drapary rod and decorative attachment at one or both ends of drapary rod, fixed to opening of door/windows, each opening n exc 1.50 mtr, contained with a pair of clamps and ap pair of side ornamental attachments complete all as specified & directed.

Disconnecting existing tanks of capacity exc. 250 but n. exc. 500 ltrs setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position including cleaning and removing all scale and dirt,etc,from tanks and from moulds of circulating pipe,etc complete all as specified and directed.

Disconnecting existing tanks of capacity exc. 500 but n. exc. 1000 ltrs setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position including cleaning and removing all scale and dirt,etc,from tanks and from moulds of circulating pipe,etc complete all as specified and directed.

S&F rotational moulded polyethylene water storage tank 500 litres capacity, ISI marked (cylindrical vertical with closed top), double wall layer construction, hoisted and fixed in position complete all as specified in SSR Part-I, making connections including 20mm bore ball valve brass with polyethylene float and fly nut and dismantling existing water tank of any capacity and removing from site complete all as specified and directed.

S&F rotational moulded polyethylene water storage tank 1000 litres capacity, ISI marked (cylindrical vertical with closed top), double wall layer construction, hoisted and fixed in position complete all as specified in SSR Part-I, making connections including 20mm bore ball valve brass with polyethylene float and fly nut and dismantling existing water tank of any capacity and removing from site complete all as specified and directed.

Demolition or breaking up AC/PVC/CI rain water/SWR pipe set in CM 100-110mm dia complete all as specified and directed.

S&F in repairs 75mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed.

S&F in repairs 110mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joints, fixed to walls with stack clamps,complete all as specified and directed.

S&F in repairs 110mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed.

S&F in repairs 75mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joints, fixed to walls with stack clamps,complete all as specified and directed.

S&F 110mm bore, PVC (SWR) junction, (single T) equal or unequal complete all as specified.

S&F 75mm bore, PVC (SWR) junction, (single T) equal or unequal complete all as specified.

M&L 75 mm size cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B-1 complete including taking down old unserviceable floor trap complete all as specified & directed.

S&F 75mm bore PVC (SWR) bends complete all as specified and directed.

S&F in repairs brass chromium plated tubular towel rail, 20mm dia, D type 60cm long , fixed to wall with CP brass screw and PVC rawl plugs, complete all as specified and directed.

S&F Brass chromium plated mixer for mixing hot and cold water, screwed down for iron pipe for 15mm dia bore pipe, fixed in repair, complete all as specified and directed.

S&F in repairs 32mm waste coupling of PTMT (half or full threaded) (minimum weight 32mm-45mm/40mm-60 gms) complete all as specified and directed.

S&F in repairs 40mm waste coupling of PTMT (half or full threaded) (minimum weight 32mm-45mm/40mm-60 gms) complete all as specified and directed.

S&F in repairs plastic water closet seat, black or white closed pattern with flat bottom, cover and mild steel chromium plated hinging device complete all as specified and directed.

S&F in repairs health faucet (ABD body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

S&F in repairs flexible waste pipe for sink, wash basin complete all as specified and directed.

S&F in repairs PVC connection 15mm size, 450 mm long with PTMT nuts complete all as specified and directed.

Finishing walls with textured exterior paint of required shade: new work (two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20 kg/10 Sqm complete all as specified and directed.

M&L preparing old decorated surfaces of walls by brooming down or steel wire brushing, scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots down and stopping etc. and applying one coat of oil bound distemper incl cleaning of floor/joinery, surfaces, glass pans etc. complete all as specified and directed.

M&L preparing old decorated surfaces of walls by brooming down or steel wire brushing, scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots down and stopping etc. and applying one coat of cement base paint incl cleaning the glass panes complete all as specified and directed.

Prepartion of old wooden surfaces of any description not other wise described over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

M/S THAKUR ENTERPRISES

Kulbir Singh Govt. Contractor