03/KMDA/EM/SE/MCI/NIT/2020_21 DT 10_

Amount

Supply, delivery at site and installation of horizontal shaft split case centrifugal pump motor complete set capable to discharge clear water of 2000 m³/hr against a tentative head of 40 MWC ,having SS(CF8M) impeller, CI casing and other standard accessories directly coupled with horizontal foot mounted (B1), TEFC, 1000 RPM (synchronous), 6 Pole, 3 Phase, 11 KV , ± 10% AC. Insulation class F , IP 55 ,Squirrel Cage Induction motor of suitable rating , entire assembly being mounted on pump vendors own manufactured common base frame (MS/CI) complete with all other accessories as required as per technical specification and direction of EIC and as per CPHEEO standard.Motor shall have a margin of at least 15% margin over the pump input at duty point or 10% margin over the maximum pump input in the worst case of the pump operation in the total range (from shut-off to run out), whichever is higher . Pumps shall be installed on suitable RCC foundation adhering to all the technical requirements of the pump manufacturer. ( 1no. working+1no. standby) Make : Pump :WPIL / Mather & Platt / KBL . Motor :CGL/Marathon/Siemens (Finally actual TDH to be determined by the tenderer at the time of detailed engineering after consultation with the concerned division dealing with the pipe laying )

Supply, delivery at site and installation of 7.5 KW vacuum pump motor complete set capable to evacuate air from suction mains, entire assembly being mounted on pump vendors own manufactured common base frame (MS/CI) complete with all other accessories including PVC tank of 1000 litresas per technical specification and direction of EIC.(capacity to be determined during detailed engineering.) Make : KBL /Equivalent

Supply, delivery at site and installation of 7.5 KW capacity dewatering pump motor complete set capable to discharge spill water from pump floor sump, entire assembly being mounted on pump vendors own manufactured common base frame (MS/CI) complete with all other accessories as required as per technical specification and direction of EIC.(capacity to be determined during detailed engineering.) Make : WPIL/KSB/KBL/Aqua/ equivalent.

Supply, delivery at site, installation of 4-Panel HT Switch Board of 350 MVA, 11 KV 18.4 KA , 800 Amps complete in all respect with all other accessories as per technical specification and direction of EIC. (1no. incomer, 2nos. transformer feeder, 1no. motor feeder) Make : Schneider/ Siemens / ABB (For KMDA HT Room )

Supply, delivery at site, installation of 4-Panel HT MCC of 350 MVA, 11 KV 18.4 KA , 800 Amps complete in all respect with all other accessories as per technical specification and direction of EIC. (1no. incomer, 2nos. motor feeder, 1no. capacitor feeder) Make : Schneider/ Siemens / ABB (For Pump house )

Supply, delivery at site, installation of LT. P.D.B. complete in all respect with all other accessories as per technical specification and direction of EIC. ( 2 nos. incomer ACB , 1 no. bus coupler , , Lighting feeders, Valve actuator feeders , EOT crane feeder, drinking water pump feeder and other auxiliary loads as required as per technical specification and direction of EIC ). Make : Sellwin Electricals Pvt. Ltd. / PCE Project Pvt. ltd / ABB .

Supply, delivery at site, installation of central control desk complete in all respect with all other accessories as per technical specification and direction of EIC. Make : Sellwin Electricals Pvt. Ltd. / PCE Project Pvt. ltd / ABB

Supply, delivery at site, installation of 110Volt DC Battery Charger with maintenance free battery complete in all respect with all other accessories as per technical specification and direction of EIC.(capacity to be determined during detailed engineering) . Make : Electro Service /Dekem/ Caldyne

Supply, delivery at site , fitting and fixing of electro-magnetic flow meter of following sizes , comprising of flow sensor and transmitter, signal conditioner if required, flow indicator, flow totaliser(controller unit ) and all other accessories complete as per specification and direction of EIC.

Supply, delivery at site fitting and fixing of following MS pipe including fabrication of all necessary accessories special viz dismantling joints, Puddle plates(20mm), Bell Mouth, bends, tees, enlarger/reducer, R.C.C. pedestal for common manifold , etc including cutting walls, pipes, making flanged & welded joints as required, fitting fixing complete in all respect including cost of all fitings, sundry and jointing materials as required for laying of pipe with anti-corrosive treatment of all pipe surface complete as per technical specification and direction of EIC.

600 mm., 12 mm thick (For individual suction piping)

500 mm., 12 mm thick (For individual delivery piping)

500 mm , 12mm thick DF Metallic dismantling joint with split flange, long stud, bolts, nuts etc.

600 mm , 12mm thick (For common manifold piping)

600 mm , 12mm thick (For flowmeter piping)

600 mm , 12mm thick (For connection to the existing 1200mm delivery line at suitable point. )

Supply, delivery at site, fitting and fixing of DIDF sluice valve (PN-1.0) of following size in proper position and alignment by providing temporaray support as required including cost of all sundry materials such as gaskets, nuts, bolts etc. all complete as required to complete the job in all respect as per technical specification and direction of EIC.

600 mm, dia (for individual pump suction side)

Supply, delivery at site, lowering, fitting and fixing of DIDF non return valve (PN-1.0 ) of following size in proper position and alignment by providing temporary support as required including cost of all sundry materials such as gaskets, nuts, bolts etc. all complete as required to complete the job in all respect as per technical specification and direction of EIC.

500 mm, dia (for individual pump delivery side)

Supply, delivery at site, lowering, fitting and fixing of DIDF butterfly valve (PN-1.0) alongwith suitable rated motorised actuator of following size in proper position and alignment by providing temporaray support as required including cost of all sundry materials such as gaskets, nuts, bolts etc all complete as required to complete the job in all respect as per technical specification and direction of EIC.

500 mm dia with head stock (for individual pump delivery line)

600 mm dia (for common header )

Supply, delivery at site, fitting and fixing of single orifice type air release valve with isolation valve of adequate size for manifold pipe line complete with all other standard accessories including cost of all sundry materials and fitting fixing charges as required as per technical specification and direction of EIC.

Supply, delivery at site, fitting and fixing of gun metal gate/globe / check valve for dewatering & drinking water lines including submersible pump ,starter panel , etc complete with all accessories including cost of all sundry materials and fitting fixing charges as required as per technical specification and direction of EIC.

50mm dia Gate / Globe Valve

32mm dia Gate / Globe Valve

50mm dia Check Valve

Supply, delivery at site, fitting and fixing of dust & damp proof following field instruments complete with all valves, cocks and other fixtures including cost of all sundry materials as required as per technical specification and direction of EIC.

0-10 kgf/cm² (6" dial compound gauge for individual suction line,accuracy ± 1%)

0-10 kgf/cm² (6" dial bourdon type for individual delivery line,accuracy ± 1%)

0-10 kgf/cm² (8" dial bourdon type for common delivery manifold,accuracy ± 1%)

Pressure transmitter including cabling (For individual delivery line )

Pressure transmitter including cabling (For common delivery manifold )

Supply, delivery at site fitting and fixing of the ultra sonic water level sensor with indicator including transmitter / transducer / stilling pipe and all other accessories including all cabling connections all complete as per specification and direction of EIC.

Supply, delivery at site fitting and fixing of float type mechanical level indicator and staff including all other accessories as per specification and direction of EIC.

Supply ,delivery at site and laying of 11 KV grade XLPE insulated, PVC outer sheathed, armoured, aluminium conductor cable of following size either through cable duct or through cable trays or through protection pipes as per technical specification and direction of EIC.

3 core x 300 mm² ( WBSEDCL room to KMDA HT room to transformers, to HT MCC to capacitor & motors) .

Supply, delivery at site and laying of all power cables , control cables , signal cables , HT terminations kit, Glands , Sockets, cable trays , supports, either through cable duct or through cable trays or burried underground through brick protection or through protection pipes as per technical specification , site requirement and direction of EIC.

Supply, delivery, fitting and fixing sheet steel fabricated double door type 4+ 4 way TPN MCB distribution board with 1 no 63A 4 pole isolator and 12 nos 6 — 32 Amps. SPMCB on wall as per requirement and direction of the EIC.

Supply, delivery at site, installation of control panel,sheet steel fabricated complete in all respect with all accessories for control of exhaust fans and other emergency loads as per technical specification and direction of EIC.

Distribution wiring with 1.1KV grade 2 X 1.5 mm² PVC insulated unsheathed single core stranded copper wire in 20mm G.I. conduit to light, fan, call bell point with 10A DP toggle switch fixed on 3mm thick bakelite cover in double door sheet metal switch board with magetic locking arrangement as per direction of the EIC.

Distribution wiring with 1.1KV grade 2 X 2.5 mm² PVC insulated unsheathed single core stranded copper wire in 20mm G.I. conduit to 250 V 15 A 6 pin composite plug socket fixed on 3mm thick bakelite cover in double door sheet metal switch board with magetic locking arrangement including 1 X 1 mm² PVC insulated unsheathed single core stranded copper wire as earth continuity wire.

Wiring with 1.1KV grade 3 X 1.5 mm² PVC insulated unsheathed single core stranded copper wire in 20mm G.I. conduit including 1 X 1 mm² PVC insulated unsheathed single core stranded copper wire as earth continuity wire from starter control panel to exhaust fan point.

Supply and fixing of Industrial type LED Tube Light fitting of make Philips , model (EnduraLED) BN308LC LED40S-6500 L120 PSU WH, completely wired up with necessary accessories , as required to maintain lux level as per IEC & as per specification & direction of EIC.

Supply and fixing of highbay luminaries of make Philips , model- Durabay Prime BY225P LED100S CW WB PSU FG GR V1 , LED fitting completely wired up with necessary accessories , including S&F of M.S. clamp on ceiling as required as per to maintain lux level as per IEC & specification & direction of EIC.

Supply and fixing of 300mm Sweep, 230 V, 1Ph, 50 Hz, 4 pole exhaust fan including S & F of M.S. cowl and making suitable hole in the wall including mending good damages complete as per specification & direction of EIC.

Supply and fixing of 600mm Sweep, 415 V, 3Ph, 50 Hz, 6 pole exhaust fan including S & F of M.S. cowl and making suitable hole in the wall including mending good damages complete as per specification & direction of EIC.

Supply and fixing of 450mm Sweep, 230 V, 1Ph, 50 Hz, 4 pole pedestal type air circulator as per specification & direction of EIC.

Fabrication and installation of structural steel works such as, cable duct cover by chequered plates, pipe & valve supports, valve operating platform, walkway ,cable supports, trays, hangers as required as per specification & direction of EIC.

Supply, delivery, fitting,fixing of fire extinguishers complete in all respect i.e. with first charge of refill, mounting bracket etc. as per technical specification and direction of EIC.

Portable type fire extinguisher (2 Kg Capacity)

5Kg. Capacity (ABC Type)

Supply and fixing on wall or on stand of 9 Ltrs capacity M.S. bucket, 50% of the bucket capacity to be filled with sand as per direction of EIC.

Earthing the whole installation as per IE Rules & Acts, specifications, complete in all respect including supply,installation of all required earthing materials,flats,earth electrodes and all other sundries,fitting,fixtures including making proper earth stations as per technical specification and direction of EIC.

Supply and providing 11KV grade rubber mat as per direction of EIC.

Supply ,installation & commissioning, of 5 MT double girder capacity EOT crane complete in all respect including testing as per technical specification and direction of EIC.

Painting the whole installation as per technical specifcation and direction of EIC.

Carrying out high pressure test of the HT installation by approved agency and obtaining necessary clearance fron Directorate of Electricity as per direction of EIC.

Supply, delivery at site , earth excavation , steel shuttering, de-watering , welding & laying of MS delivery pipe , common manifold, flowmeter , BFV and main delivery pipe including fabrication of all necessary accessories special ,enlarger, ,R.C.C. / fabricated pedestal , thrust blocks , etc including cutting pipes, making flanged & welded joints as required, for joining the common delivery manifolds with the existing prelaid rising main pipes complete as per technical specification and direction of EIC. Note : Any mechanical or electrical or civil , parts/spare/equipment not included in the BOQ but required to complete the project is to be supplied by the agency at free of cost .

Operation and maintenance of the entire CWPS with daily consumables for a period of one year along with supply of trained staffs as required to run the pumping station .

Mate Consultants Pvt. Ltd.

MACHINE SUPPLIERS SYNDICATE PVT LTD