Construction of 50 Bedded Critical Care Block Under Emergency Covid Response Package-II at Roorkee in District Haridwar Uttarakhand.

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Filling available excavated earth (excluding rock) in trenches ,plinth,sides of foundation etc . in layers not exceeding 20cm in depth ,consolidating each deposited layer by ramming and watering lead upto 50m and lift upto 1.5m .

Filling with available fly ash and earth (excluding rock) in trenches or embankment in layers (each layer should not exceed 15 cm), with intermediate layer of compacted earth (Soil density of 98%) after every four layers of compacted depth of fly ash, sides & top layer of filling shall be done with earth having total minimum compacted thickness 30 cm or as decided by Engineer -in-charge, including compacting each layer by rolling/ ramming and watering, all complete as per drawing and irection of Engineer -in - charge.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Providing and laying in position cement concrete 1:4:8 (1cement :4 coarse sand:08graded brick aggregated 40mm .nominal size.) excluding the cost of centering and shuttering - All work upto plinth level

Making plinth protection 50mm thick of cement concrete 1:3:6 (1cement :3 coarsesand : 6graded stoneaggregate 20mm nominal size) over 75mm bed by dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately).All works upto plinth level

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately).All works above plinth level upto floor V level

Centering shuttering including strutting, propping etc. and removal of form work

FOUNDATION UP TO PLINTH

COL SUPER STRUCTURE

Roof Beam

Staircase

Lintel+sunshade

Reinforcement for R.C.C work including straighting,cutting,bending ,placing in position and bending all complete Thermo-Mechanically Treated bars.

230 th Brick work with brick of class designation 75 in foundation & plinth in cement mortar 1:6

Brick work with F.P.S bricks of class 75 in super structure above structure above plinth level up to floor five level in all shapes and sizes in cement mortar 1:6 (1 cement : 6 coarse sand )

Half brick masonry with F.P.S bricks of class designation 75 in superstructure above plinth level up to floor five level in cement mortar 1:4 ( 1 cement : 4 coarse sand)

Extra for providing and placing in position 2 Nos. 6mm dia. M.S.bars at every third course of half brick masonry (with F.P.S.bricks).

Stone work in plain ashlar in super structure upto floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) including pointing with cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : One face dressed Red sand stone

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.

Providing/fixing M.S. grills of riquired pattern in frames of windows etc. with M.S. flat, square or round bars etc. all complete Fixed to steel windows by welding.

Providing & fixing of wire mesh (mosquito jalli) with labour & material comlete With 12 mm mild steel U beading.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing chromium plated brass handles with necessary screws etc. complete: 75 mm

Providing and fixing aluminium sliding door bolts, ISI marked anodised(anodic coating not less than grade AC 10 as per IS : 1868),transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16 mm

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete 100x10 mm

Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. Single rubber stopper

Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete

Providing and fixing factory made ISI marked steel glazed doors, windowsand ventilators, side /top /centre hung, with beading and all members such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment).

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with 4.0 mm thick glass panes

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade Area of slab upto 0.50 sqm

P/F 1st quality ceramic glazed wall tiles conforming to IS : 15622 of approved make in colours , shades except burgandy , bottel green , black of any sizes as approved by Engineer -in -Charge in skirting , risers of steps and dados over 12 mm thick bed of cement mortar 1:3 and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing 10 mm thick acid and/or alkali resistant tiles of approved make and colour using acid and/or alkali resisting mortar bedding, and joints filled with acid and/or alkali resisting cement as per IS : 4457, complete as per the direction of Engineer-in- Charge. In flooring on a bed of 10 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand) Acid and alkali resistant tile

Providing and fixing 10 mm thick acid and/or alkali resistant tiles of approved make and colour using acid and/or alkali resisting mortar bedding, and joints filled with acid and/or alkali resisting cement as per IS : 4457, complete as per the direction of Engineer-in- Charge. In dado/skirting on 12 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand) Acid and alkali resistant tile

Chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) Medium shade pigment using 50% white cement, 50% ordinary cement

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 800x800 mm

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

12mm thick plaster on the plain in side of mix 1:6 ( 1 cement : 6 fine sand) mortar

15mm thick plaster on the plain in side of mix 1:6 ( 1 cement : 6 fine sand) mortar

6mm thick cement plaster of ceiling of mix 1:3 ( 1 cement : 3 fine sand) mortar

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade Two or more coats on new work over an under coat of suitable sq.m shade with ordinary paint of approved brand and manufacture.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. 12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16mm thick fire retardant PVC film on the face side and 12micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit.

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep chase

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Supplying and fixing following way SP&N steel sheet MCB distribution board of 240 volts on surface/ recess complete with tinned copper bus bar, neutral link, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator) 12 Way Double door

Supplying and fixing following way horizontal type three pole and neutral steel sheet MCB distribution board of 415 volts on surface/ recess complete with tinned copper bus bar, neutral link, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator)

4 Way (4+12), Double door

6 Way (4+18), Double door

8 Way (4+24), Double door

Supplying & fixing following rating, double pole (single phase and neutral), 240V residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying & fixing 5 amps to 32 amps rating 240 /415 volts,10KA, C series, Miniature Circuit Breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single Pole

Double Pole

Supplying & fixing of single pole blanking plate in the existing MCB DB complete etc. as required

Supplying and fixing following way prewired TP&N MCB distribution board of steel sheet for 415 volts on surface/ recess complete with loose wire box, terminal connectors for all incoming and outgoing circuits, duly prewired with suitable size FRLS PVC insulated copper conductor up to terminal blocks, tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnections, powder painted including earthing etc. as required.(But without MCB/ RCCB/RCBO/ Isolator) 12 Way (4+36), Double door

Supplying & fixing 240 /415 volts C series, Miniature Circuit Breaker suitable for inductive loads of following rating and poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63A FOUR POLE

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc.as required. Group C

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit along with 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required

2x 1.5 sqmm+ 1x 1.5 sqmm earth wire

2x 2.5 sqmm+ 1x 2.5 sqmm earth wire

2x 4 sqmm+ 1x 4 sqmm earth wire

2x 6 sqmm+ 1x 6 sqmm earth wire

2x 10 sqmm+ 1x 6 sqmm earth wire

4x 6 sqmm+ 2x 6 sqmm earth wire

4x 10 sqmm+ 2x 6 sqmm earth wire

4x 16 sqmm+ 2x 6 sqmm earth wire

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

Supplying and fixing two module Stepped type electronic fan regulator on the existing modular plate & switch box including connections but excluding modular plate etc. as reqd.

Supplying and fixing brass batten/ angle holder including connection etc. as required.

Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top along with 20 amps "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing DP sheet steel encosure on surface/ recess along with 25/32 amps, 240 volts, "C" curve, DP, MCB complete with connections, testing and commissioning etc. as required.

Supplying and fixing TP sheet steel encosure on surface/ recess along with 16/25/32 amps, 415 volts, "C" curve, TP, MCB complete with connections, testing and commissioning etc. as required.

Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc as required.

150 mm X 150 mm X 60 mm deep

200 mm X 150 mm X 60 mm deep

200mm x 125 mm x 60 mm deep

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing of following sizes of steel conduit along with accessories in surface / recess including painting in case of surface conduit,or cutting the wall and making good the same in case of receeesed conduit as required.

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types,complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (up to 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Upto 450 mm sweep

Providing and fixing circular / hexagonal M.S sheet ceiling fan box with clamp of internal dia 140 mm,73 mm height, 3 mm thick rim, top and bottom lid of 1.5 mm M.S sheet. Lids shall be screwed into M.S box by means of 3 mm round headed screws, clamps shall be made of 12 mm dia M.S bar bent to shape as per standard drawing with over all length as 80 cm.

LIGHT FIXTURE

1 x 20 watt Surface mounting type LED light fixture complete with all accessories as required.

1 x 15 watt Recess mounting type LED light fixture complete with all accessories as required.

1 x 18 watt Recess mounting type LED light fixture complete with all accessories as required.

1 x 36 watt recess mounting type LED light fixture complete with all accessories as required.

1 x 31 watt wall mounting personal LED light fixture complete with all accessories as required.

1 x 9 watt surface mounting type LED Mirror light fixture complete with all accessories as required.

1 x 11 watt surface mounting type LED Bulk Head light fixture complete with all accessories as required.

1 x 80 watt LED Flood light fixture complete with all accessories as required.

Exhaust fan of 230mm sweep, 1400RPM, with 450 CFM free air delivery, AC 230V/415V , 50 Hz, single phase / three phase complete with all necessary accessories for completing installation as per specification.

Supply of following sizes of ceiling fan complete with double ball bearing. motor, blades, downrod, canopy, capacitor, regulator etc. suitable for operation on 230 volts 50 Hz A.C. supply complete as required. Size 1200mm.(Speed Star)

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

Fixing of lightning conductor finial (single prong) with base plate including holes etc. complete as required.

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or on surface of wall for lightning conductor complete as required.(For horizontal run)

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or on surface of wall for lightning conductor complete as required. (For vertical run)

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 Nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.

Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.

Supplying, installation, testing & commissioning of repeater panel wih 320 character/ Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required.

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required.

Supplying, installation, testing & commissioning of fault isolator complete with base as required.

Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required.

Supplying, installation, testing & commissioning of addressable fire control module complete as required.

Supplying, installation, testing & commissioning of addressable manual call point complete as required.

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required

Supplying, installation, testing & commissioning of fire fighter telephone handset complete as required.

Supplying, installation, testing & commissioning of fire fighter phone jack complete as required.

Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required.

Supplying, installation, testing & commissioning of 1.5/3/6W metal box ceiling/wall speakers complete as required.

Supplying, installation, testing & commissioning of digital audio amplifier 75 Watt, 25V rms operating at 240 Volt AC Supply complete as required.

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required. speaker cable Single pair, 2-core, 1.5 sqmm

Supply, Installation, Testing & Commissioning of CAT 6A UTP LSZH Cable, 23 AWG solid copper conductors in accordance to TIA/EIA 568 C.2 (Category 6a) & ISO/IEC 11801 2nd ed(Class Ea), UL Approved, tested @500 Mhz, with HDPE insulation of individual conductor and over all Dia of 7.2 mm for Connectivity of Hub room to End Point. Grey Color

Supply, Installation, Testing & Commissioning of CAT 6A UTP Universal (both tool & toolless) information outlet (I/O) in accordance with ANSI TIA 568 C.2, IEC 60603-7-4 2nd Edition, ISO/IEC TR 11801-9901-2014, ROHS Compliant. The I/O should have minimum 750 mating cycle and 200 insertion cycle and UL approved,for Data, Voice, & Wi-Fi at user end.

Supply, Installation, Testing & Commissioning of loaded 24 port CAT 6A UTP, Transparent shutter jack panel, 1U height, UL-94V-0, Black with cable support bar, clear label marks and earthing plug for CAT6A cable termination at rack end.

Supply, Installation, Testing & Commissioning of CAT 6A UTP, LSZH Patch Cord as per ANSI/TIA/EIA 568C.2 and UL 94-V-0, ROHS Compliant, patch cord 1 Mtr for rack side switch to jack panel connectivity.

Supply, Installation, Testing & Commissioning of CAT 6A UTP, LSZH Patch Cord as per ANSI/TIA/EIA 568C.2 and UL 94-V-0, ROHS Compliant, patch cord 2 Mtr for rack side switch to end user connectivity.

Supply, Installation, Testing & Commissioning of 1, 2 and 4 port face plate, British Style with Shutter, 2 Plate system clear finish with transparent labelling, ABS-UL94-V2, ROHS Compliant, in accorandce with standards like ANSI/TIA-568-C.2, ISO/IEC 11801:2002 AMMD.2:2010, YD/T 926.3-2009 & ISO/IEC 60603-7 white for I/O fixing at user side.

Supply, Installation, Testing & Commissioning of 42 U (600W/1000D) floor mount rack with fans , 2 cable managers , satationary shelf , 2 Nos. of hardware pkts.

Supply, Installation, Testing & Commissioning of 15U wall mount rack with fans , 2 cable managers , satationary shelf , 2 Nos. of hardware pkts.

Supply, Installation, Testing & Commissioning of Pure IP at core server Based voice solution with 04 Port Voicemail ,04 Port FXS ,04 Port FXO ,1 PRI Trunk lines (30 Ch) Circuit with CLIP Facility , 55 IP users License ,01 Nos. IP Operator Console, 100 Party Conference ,Speed Dial, Music on Hold , Internal/ External ring difference ,Call Barring, Call Pickup, TEC should be with GR Number, - Should Support Redundant server in active-Active mode.

Supply, Installation, Testing & Commissioning of Type 1 IP Phone 1 VoIP account , Full duplex speaker phone, IPV6, 2xLAN, PoE .

Supply, Installation, Testing & Commissioning of Type 2 IP Phone with 2 Voip accounts, 2 Lines , HD Voice,Graphic LCD display with backligh.

Supply, Installation, Testing & Commissioning of Core Switch 24 Port POE+ Access Switches with switching capacity of 240 Gbps, forwarding performance 190 Mpps, having 24 x 10/100/1000BASE-T PoE-plus(RJ45) with minimum PoE budget of 370W and 4 x 10G SFP+ uplink ports, should have support for 9 switch Stacking with stacking cable with bandwidth of minimum 120 Gbps. Should support min 2GB internal DRAM, 2GB internal Flash memory, 32K MAC address, 4k Multicast Routes, Should have static Routing from day 1 and upgradable to support OSPF and VRRP with 1 year support.

Supply, Installation, Testing & Commissioning of 24 Port POE+ Access Switches with switching capaticy of 128 Gbps, forwarding performance 95 Mpps, having 24 x 10/100/1000BASE-T PoE-plus(RJ45) with 2 x 10G SFP+ uplink ports. Should support for Stacking/VC with stacking cable with stacking bandwidth of maximum 40 Gbps as and when required. Should support min 2GB internal DRAM, 2GB internal Flash memory, 16K MAC address. Should have Static Routing , Neighbor discovery, system logging, Telnet, SSH, SNMP, Network Time Protocol (NTP), Domain Name System (DNS) and IPv6 features from day 1 and should support OSPF, VRRP, OSPFv3 and PIM.

Supply , Installation , Testing and commissioning of CAT 6 UTP cable 23 AWG LSZH as per ANSI/TIA 568 C.2 and ISO/ IEC 11801–2nd Edition, ROHS Compliant, solid copper conductors, tested @250 Mhz, with HDPE insulation of individual conductor and over all Dia of 5.8mm for Connectivity of Hub room to End Point.

Supply, Installation, Testing & Commissioning of CAT 6 UTP Universal (both tool & toolless) information outlet (I/O) in accordance with ANSI TIA 568 C.2, IEC 60603-7-4 2nd Edition, ISO/IEC TR 11801-9901-2014, ROHS Compliant. The I/O should have minimum 750 mating cycle and 200 insertion cycle and UL approved,for Camera at user end.

Supply, Installation, Testing & Commissioning of loaded 24 port CAT 6 UTP, Transparent shutter jack panel, 1U height, UL-94V-0, Black with cable support bar, clear label marks and earthing plug for CAT6 cable termination at rack end.

Supply, Installation, Testing & Commissioning of CAT 6 UTP, LSZH Patch Cord as per ANSI/TIA/EIA 568C.2 and UL 94-V-0, ROHS Compliant, patch cord 1 Mtr for rack side switch to jack panel connectivity.

Supply, Installation, Testing & Commissioning of CAT 6 UTP, LSZH Patch Cord as per ANSI/TIA/EIA 568C.2 and UL 94-V-0, ROHS Compliant, patch cord 2 Mtr for rack side switch to end user connectivity.

Supply, Installation, Testing & Commissioning of 1, 2 and 4 port face plate, British Style with Shutter, 2 Plate system clear finish with transparent labelling, ABS-UL94-V2, ROHS Compliant, in accorandce with standards like ANSI/TIA-568-C.2, ISO/IEC 11801:2002 AMMD.2:2010, YD/T 926.3-2009 & ISO/IEC 60603-7 white for I/O fixing at user side.

Supply, installation, testing and commissioning of 5 MP Dome camera , ONVIF profile S , G& T ,UL , CE , FCC Certified ,1/2.7” Progressive Scan CMOS ,2.7 mm to 13.5 mm motorized varifocal lens , Quad stream with each stream support H.265 compression simultaneously ,min illumination : Color 0.05lux @ F1.2(AGC ON) ; B/W 0 lux @ IR ON , Shutter speed : 1 / 5s ~ 1 / 100,000 s ,WDR , Compression : H.265/H.265+/H.264/H.264+ .SD card support upto 256GB , Alarm trigger - 1 input / 1 output , frame rate : Main stream should support 25 fps@5MP ,Edge analytics : Customer Flow staistics, Cross COunt, Heat Map, Human & Vehicle Detection, Pedestrian Intrusion Detection & Line cross Detection. Queue length detection, Regional population statistics, SOD-Stationaary Object Detection. , In built IR LED , IR Distance upto 45 meters , IP 66 ,IK10,POE.Audio -1 input/1 output

Supply, installation, testing and commissioning of 5 MP Bullet camera , ONVIF profile S ,G & T . UL , CE , FCC Certified ,1/2.7” Progressive Scan CMOS ,2.7 mm to 13.5 mm motorized varifocal lens , Quad stream with each stream support H.265 compression simultaneously ,min illumination : Color 0.05lux @ F1.2(AGC ON) ; B/W 0 lux @ IR ON , Shutter speed : 1 / 5s ~ 1 / 100,000 s ,WDR , Compression : H.265/H.265+/H.264/H.264+/MJPEG .SD card support up to 256Gb, Alarm trigger - 1 input / 1 output , frame rate : Main stream should support 25 fps@5MP , Edge analytics : Customer Flow staisticsCross Count, Heat Map, Human & Vehicle Detection, Pedestrian Intrusion Detection & Line cross Detection. Queue length detection, Regional population statistics, SOD-Stationaary Object Detection. , IR Distance upto 45 meters , IP 66 , POE. Audio -1 input/1 output

Supply, installation, testing and commissioning of ONVIF profile S & G ,UL certified 32 Channel NVR , 4 SATA ports , each SATA capacity of upto 8 TB , Recording Bandwidth 320 Mbps , 1 X HDMI , 1 X VGA , Alarm : 16ch in / 1ch out , 1 X RJ45 port , 1x3.0 USB for backup / upgrade, 2x 2.0 USB for mouse , Smart Phone support : iOS, Android.

Supply, Installation, Testing & Commissioning of 8TB Surviellance Hard Disk.

Supply, Installation, Testing and Commissioning of Full HD 55" LED Professional Display Panel.

Supply, Installation, Testing and Commissioning of Workstation PC: Intel(R) Core(TM) i7-3770 Processor (8M Cache, up to 3.90 GHz); RAM: 8GB (1x8GB) Non-ECC DDR3 1600MHz ; Keyboard: 12 function keys; Chassis: Tower/Workstation; DVD: 8X Slimline DVD+/-RW, Data Only; Dual Graphics Card; Network interface card: Integrated Intel(R) 82579LM Gigabit1 Ethernet LAN 10/100/1000; Hard disk: 250GB, 7200 RPM 3.5" SATA 6Gb/s Hard Drive; Operating system: Windows 7 Professional 64 Bit or latest.

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.

2 x 1.5 sq. mm (For Bed Switch/ Toilet Module to Main Nurse Call Panel)

4 x 1.5 sq. mm (For Bed Switch to Dom Light)

Supplying and fixing of following sizes of steel conduit along with accessories in surface / recess including painting in case of surface conduit,or cutting the wall and making good the same in case of receeesed conduit as required.

Supply, Installation, Testing and commissioning of Microprocessor controller Nurses station with terminal monitor with in built power supply , with charger enclosed in a powder coated cabinet . Having with Reset, alarm/ buzzer, Call acknowledge with battery back up, battery charger complete system as per technical specifications and as per required of following suitable configuration. complete as per specification .

Supply, Installation, Testing and commissioning of Bed Call Push Button with LED indication and Flexiable Cord with button , Call Reset , Call Indication, station for each Bed complete as required.

Supply, Installation, Testing and commissioning of LED Indicators Module (Dom Light) at Outside of each ward complete as required.

Supply, Installation, Testing and commissioning of Toilet Call Push Button with LED indication and flexiable cord with button , Call Reset , Call Indication, station for each Bed complete as required.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap

Providing and fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink without drain board 610x510 mm bowl depth 200 mm

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 MM

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5° 110 mm bend

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete 110 mm

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.

Providing and fixing 600 x 455 mm. bevelled edge mirror of Saint Gobin or Modi float glass complete with 6 mm. thick hard board ground fix to wooden cleats with CP brass screws and washers etc. complete.

Providing and fixing terminal guard : Sand cast iron S&S as per IS - 3989

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : Sand cast iron S&S as per IS - 3989

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge Internal work - Exposed on wall

15mm dia nominal bore

25 mm dia. nominal bore

50 mm dia. nominal bore

Providing and fixing ball valve (brass) of approved quality complete High or low pressure with plastic floats 25 mm dia. nominal bore

Providing and fixing gun metal non- return valve of approved quality (screwed end) : 25 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions : 15mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing & Fixing C.P. brass bib cock parryware make

Providing & Fixing C.P. brass Long boddy bib cock

Providing and fixing PTMT pillar cock of approved quality and colour

Providing & Fixing C.P. brass stop(conceald)

Providing & Fixing C.P. brass angle valve

Providing & fixing c.p. soap dish parryware make

Providing & fixing Over Head Shower parryware make

Provding & Fixing C.P Towel rail parryware make

Provisiding & Fixing C.P Paper Holder parryware Make

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.

65 mm dia nominal bore

40 mm dia nominal bore

40 mm dia nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 80 mm nominal bore

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 coarse sand (Zone III) : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:Inside dimensions 455x610 mm and 45 cm deep for single pipe line : for sanitary building

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 100 mm dia. R.C.C. pipe

Earth work in excavation by mechanical means ( hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sq.m on plan ) including disposal of excavated earth, lead upto 50 m and lift upto 1.50 m, disposed earth to be levelled and neatly dressed. All kinds of soil.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

40 mm. thick cement concrete flooring 1 :2 : 4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm. nominal size ) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete.

Providing & fixing of R.C.C manhole covering tank (600 x 600)

Providing & fixing of foot rest in tank

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200mm

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level.

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -incharge.

Centering shuttering including struttings, propping etc. and removal of form work

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix :1:4 (1 cement: 4 fine sand)

Providing & fixing of R.C.C manhole covering Septic tank

E.T.P. (caoacity (m3/day)- Range 400-6000)

Water filter plant (capacity 2 kl/hr

Sundigital Drop Arm Barrier (boom barrier),as perMHA QR for drop arm barrier (boom barrier),

STP Electro -Mechnical supply and required designed MS Structure work.

STP Installation & commission charges

Drilling of 100 mm dia Mini Tubewell 100 meters deep by Rig machine as per unit estimate.

Supply of submersible pumping plant capable of delivering 200 lpm discharge at 150 m head, with electric motor to be operated on 415+\-10% volts, 3 phase, 50 c\s AC supply with 5m submersible cable.

Supply of stand by submersible pumping plant capable of delivering 200 lpm discharge at 150 m head, with electric motor to be operated on 415+\-10% volts, 3 phase, 50 c\s AC supply with 5m submersible cable

Supply,installation testing and commisioning (SITC) on turkey bassis for fully automatically pump automation control pannel of different capacities having intelligent unit having "" FIELD PROGRAMMABLE LOGIC CONTROLERS BASED ,SCADA OPERATED PUMPS motor start , run , control protect against fault automatically operated control and data Acquistion system system at pumping water supply schemes.50 hp of simplex make.

Power wiring and earthing material as per standards. Power wiring 1x3x10 sq.mm.

Supply of main piping and valves of 100 mm size having following items. 100 mm dia x 4.8mm thick column pipe in 3m length with inter-locking arrangement 100 M. 100 mm dia CI D\F sluice valve with hand wheel 2 Nos. 100 mm dia CI D\F reflex valve 1 No 100x100x100 mm dia Tee 1 No 100 mm dia CI D\F bend 2 Nos. 100 mm dia MS D\F pipe of 1.5M length 2 Nos Ventury 1 No MS DI clamp 2 pair TW Cap 1 No Guages 1 set Necessary nut, bolts and packings.

Supply of 25 mm thick rubber resistance insulated sheet of size 2m x 1m.

Installation and commissioning of pumping plant and accessories

Supply of electronically controlled, electrically actuated, diaphragm operated, chemical metering pump, wall mounting suitable for delivering up to 10 litres of chemical solution/ sodium hypochlorite solution per hour under maximum delivery pressure up to 10 Kg/cm2 and suction lift not less than 1.5metre with accessories.

Provision for 200 liters plastic tank for storage of sodium hypochloride including supply, cartage & installation at tubewell site including all material, labour, T&P etc complete.

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns,pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

Centering shuttering including strutting, propping etc. and removal of form work

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:Profile B Fixing with adjustable

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strikeplate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineerin-charge:(profile c) Fixing with adjustable lugs with split end tail to each jamb

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade New work (two or more coats) over and including priming coat with cement primer.

52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement.18 mm thick

Providing and fixing PTMT door catcher of length 72 mm and dia. of 42 mm with suitable washers weighing not less than 33 gms.

Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Providing and fixing soil, waste and vent pipes : Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989 100MM

Providing and fixing M.S. stays and clamps for sand cast iron/ centrifugally cast (spun) iron pipes of diameter : 100 mm dia

Supplying and fixing Single Headed Internal Hydrant Valve oblique pattern with instantaneous Stainless Steel coupling of 63 mm dia with cast iron wheel ISi marked, conforming to IS : 5290 (LTB2 ), with 80 mm dia flanged inlet with ABS cap and chain complete with all accessoriesWATER TEST 21 Kgf/CM, 900 LPM DIS etc., as required. Make Atasi / Andex

Supply, Installation, Testing and Commissioning 100°/o synthetic flax canvas Non-percolating FIRE hose (Type A), LS.I 636 marked 163mm dia x 1Sm long with stainless steel male & female couplings (IS 903 marked 63 m.m. dia x 15 m long with stainless steel male and female couplings (IS 903 marked) bound and rivited to hose pipes with G.I. rivits and copper wire as required.

Supply ,installation testing and commissioning of 63 mm dis. Stanless steel Branch nozzale 18:903 material LTB-2 tested at 21 kgflcm2 hydraulic test na swater test at 14 Kgf/CM2

Supplying and Fixing First Aid Hose Reel, wall mounting swinging type complete with drum & bracket of MS construction! spray painted in Post office Red, confirming to IS 884/1995 with upto date amendments, complete with the following as required: 30 Meter long 20 mm dia water hose Thermoplastic (Textile reinforced) Type - 2 as per IS : 12585 25 mm dia gun metal ball valve & abs nozzle. Drum and brackets for fixing the equipments on wall. Connection from riser with stop valve (gun metal) & M.S. Pipe .

Supplying, installation, testing and commissioning of weather proof M.S cabinet size 900 mm x 600mm x 300mm deep fabricated from 1.6mm thick M.S. sheets and M.S angle 40mm x 40mm x 6mm complete with glass, locking arrangements to accommodate the following: - with key stand The cabinet shall be painted with one coat of primer and 2 coats of synthetic enamel paint of approved red shade.

Providing and fixing single stainless steel wight app 22-25 Kg suction collecting head as per IS : 904-1983, hose coupling (draw out connection) with female outlet as per 903 cpmplete with 150 m.m.dia G.I. suction pipe with puddle flange with strainer complete as per drawings.

Supply and installation testing of cat Iron body Non Return valve with nuts, bolts.\Washer, etc compte in all respects 100 mm Make Kartar / Castel

Supplying, laying.fixing, testing and commissioning of following sizes (NB) of ISI marked heavy ·s·c1ass M.S. pipes including cutting, threading, welding ,etc. and providing all fittings e.g. elbows, reducers, ctamps, hangers. flanges, gaskets, nuts. bolts and washers etc. including painting of pipes and fittings with red paint over a coat of raedy mixed primer of following sizes Make Jindal / Surya

100m.m. dia

25m.m. dia

Supplying, Installation; Testing and Commissioning of Butterfly valves of PN 1.6 rating of following sizes with nitrile Bronze I G.M. seat duly ISi marked and stainless steel stem with lever/gear operation and cast iron body in powder coated finish for fire fighting application complete in all respects confirming to IS: 13095 as required. Make kartar/ castel 100 MM dia

Providing, Installation, Testing and Commissioning of Gun Metal Bal Valves with brass body chrome plated of following sizes as required. 25 mm dia

Providing, Installation, Testing and Commissioning of Air release valve with brass bod chrome plated of following sizes as required.

Supply testing and commissioning G.matel Foot valve 100 mm

Supply testing and commissioning of electric Driven Jockey Pump suitable for auto/manual operation and consistion of horizontal centrifugal & suction back pullout type capable ot delivery 7.5 H.P 70 mtr. Head model 32/30 make kirloskar/ mather and platt

Supply and installation of A.B.C POWDER TYPE MONO AMMONIUM PHOSPHATE RATEING WITH GOOD BODY SIZE 1.6 MM MILD STEEL BODY EXTINGUISHER MEDIA ASPER IS 14609/IS4308 PROPELLENT NITROGEN/ SERVICE PRESSURE 15 KGF/CM2, HYDRAULIC TEST PRESSURE IS 35 KGF/CM2 AND ISi MARKED AS PER IS 15683 WITH ALL ASSOSORIES OR ALL CATIFICATE OF GOV. STANDERD MAKE ATASI'/ ANDEX

2 KG (FIRE RATING 1A & 88)

4 KG (FIRE RATING 2A &218)

SUPPLY AND INDSTALLATION OF CLEAN AGENT ACTUALLY WORKS ON FLAMMABLE LIQUIDS.GASES AND ELECTRICAL STARTED FIRE AS IS CODE 15683 ,FILLING RATIO 0.667 TEST PUESSURE 250 . KGF/CM2, OPERATING TEMPERATURE -20C* TO -55*C DISCHARGES 95 o/o FIRE RATING 21 B MAKE ATAS I'/ ANDEX I OEM 4.5 KG TYPE (FIRE RATING 21 8)

SUPPLY AND INSTALLATION OF WATER CORSON DI-OXIDE 50 LTR . WHEEL MOUNTEDAN D STAND FIRE EXTINGHUSERW C02 ACTUALLU WORKS ON PAPER, WOOD, PAPER, PLASTIC, ETC AS PER IS 904 CATIAGE TYPE MAKE ATASI'/ ANDEX

SUPPLY AND INSTALLATION OF FOAM TYPE(AFFF 50 LTR. WHEEL MOUNTEDAND STAND FIRE EXTINGHUSER S ACTULY WORKS ON PAPER, WOOD, PAPER, PLASTIC,PTROL DIESEL PAINTS RUBBER WAX LAC AND ALL VOLATILE LIQUIDS ETC AS PER IS 904 CATTAGE TYPE MAKE ATASI'/ ANDEX

AIR RELEASED TANK WlTH SlREN .

S/F Kirlosker Deisel Engine With Pump & auto start Compleat with all ascessories , fixed in all .

Providing & Fixing decorative high pressure laminated Panel , including cost of adhesive of approved quality. ACP Sheet 10 year warranty colour fade and bubbles makeALDEKO MS Pipe 1”x2”, approx weight-8-9 kg/pipe.(make-apollo) Ms Pipe 1 coat primer and 1 coat paint include in this rates. Silicon weither proof 789 Hpl repit.

Providing & Fixing decorative structure glazing work , including cost of adhesive of approved quality. 5mm reflacted tougthend glass aluminium section 2’’x2’’-16 gauge Silicon weither proof 789

Providing and laying Epoxy flooring

S.S. wall panelling including fixing on walls all complete.

Providing & fixing of sticker pasted acrylic name plates for room including all labour, complete in all respect as per directed by engineer in charge.

Providing & fixing of emergency evacution marking system backside including all labour, complete in all respect as per directed by engineer in charge.

Sanjay Agarwal Pvt Ltd (BID ID -355161)

M/S P.N VYAS & SONS (BID ID -355145)