CONSTRUCTION OF MUNSIFF COURT COMPLEX AT PADUM ZANSKAR

Amount

Excavation work in excavation by mechanical means (Hydraulic excavator)/manual means in foundation trenches or drains (not exceeding 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.

ORDINARY ROCK 20%

ALL KINDS OF SOIL 80%

Filling available excavated earth (excluding rock) in trenches plinth, sides of foundation etc in layer not exceeding 20cm in depth consolidating each deposited layer by ramming and watering, lead upto 50cm and lead up to 50 m and lift upto 1.5 mtr.

STONE SOLLING (Dumping of stone including cost of stone (on horizontal)

Providing and laying position cement concrete of specified grade excluding the cost of centering and shuttering. All work upto plinth level 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) (crushed) including all carriage complete

Providing and laying position cement concrete of specified grade excluding the cost of centering and shuttering. All work upto plinth level 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) (crushed) including all carriage complete

Providing and laying position cement concrete of specified grade excluding the cost of centering and shuttering. All work upto plinth level 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) (crushed) including all carriage complete

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, column, pillars, piers, abutments, posts and struts etc. upy floor five level excluding cost of centering, shuttering, finishing and reinforcement: 1:1:2 ( 1 cement : 1 coarse sand : 2 graded stone aggregate 20mm nominal size). including all carriage complete

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more. including all carriage complete

Centering and shuttering including strutting, propping etc. and removal of form for: Foundation, footing bases of column

Centering and shuttering including strutting, propping etc. and removal of form for: Columns, pillars, piers, abutments, posts and struts

Centering and shuttering including strutting, propping etc. and removal of form for: Lintel beams, plinth beams, griders, bressument and cantiliver

Centering and shuttering including strutting, propping etc. and removal of form for: Suspended floors, roofs, landings, balconies and access platform.

Providing and laying autoclaved aerated cement blocks masonry with 100/150/225 mm thick AAC blocks in superstructure above plinth level upto floor V level in cement mortar 1:4 (1 Cement : 4 coarse sand ) and curing complete. The rate includes providing and placing in position 2 nos. 6 mm dia M.S bars at every third course of masonry work.including all carriage complete

Providing & fixing upto floor five level precast cement concrete solid blocks including hoisting and setting in position in cement mortar 1:3 (1cement:3 coarse sand), cost of required centring, shuttering and curing complete 1:3:6 (1 cement : 3 coarse sand : 6 graded crushed stone aggregate 20 mm nominal size) including all carriage complete

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or dash fastener shall be paid for seperately) Sal wood

Providing and fixing panelled and glazed shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for seperately,all complete as per direction of Engineer-in-charge.(second class teak wood 35 mm thick shutter)

Providing fixing paneling and glazing in panalled or panalled glazed shutters for door/windows 25mm to 40mm thick of 1st class kail wood.

Providing and fixing factory made uPVC AIS or FENISTA make white/ wooden colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sashshall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Casement cum fixed panel window having both end single casement panel, middle fixed panels and at top completely fixed ventilator with S.S friction hinges (350 x 19 x 1.9) made of (big series) frame 67 x 60 mm , sash 67 x 80 mm &mullion 67 x 80 mm all having wall thickness of 2.3 ± 0.2 mm and single glazing bead/double glazing bead of appropriate dimension. (Area of window above 3.00 sqm upto 5.00 sqm).

Providing and fixing factory made uPVC white/ wooden colour fixed glazed windows/ventilators comprising ofuPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerancein dimension i.e. in depth & width of profile shall be acceptable. Variation inprofile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)

Providing and fixing DGU ( with <0.25 SHGC and >0.35 VLT glazing in uPVC window, ventilator shutters and partitions etc. with proper sealing as per norms etc. complete as per the architectural drawings and the directions of engineerin- charge. ( Note : DGU with <0.25 SHGC and >0.35 VLT)

TOUGHENED DGU glass panes of 5.0 mm thickness SAINT GOBAIN / ASAHI INDIA GLASS / HNGIL make as approved by engineer in charge. Qty vide window openings @80%

Providing and fixing casement handle made of zinc alloyed (white powder coated) for UPVC casement window with necessary screws etc. complete.

Pebble dash plaster upto 10m height above ground level with a mixture of washed pebble or crushed stone 6mm to 12.5mm nominal size dashed over and including fresh plaster in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 Coarse sand) and top layer 10mm cement plaster with cement mortar 1:3 (1 cement: 3 fine sand) mixed with 10% finely grounded hydrated lime by volume of cement.

CEMENT PLASTER (IN COARSE SAND) 12mm Cement plaster of mix 1 : 4 ( 1 cement : 4 coarse sand) (PPC or cement with >25% flyash is recommended.)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade. New work (two or more coats) over and including water thinnable priming coat with cement primer

Applying priming coat: With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood) (Note: It Should have Low or No VOC as per Green Building guidelines)

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. (Note: It Should have Low or No VOC as per Green Building guidelines)

New work (Two or more coats applied @ 1.43 litre/10 sqm. Over & including priming coat of exterior primer applied @ 0.90 litre/10 sqm. (Note: It Should have Low or No VOC as per Green Building guidelines)

Preparing newly primed wooden surface for painting by way of filling of putty sand papering rubbing complete.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade: Two or more coats on new work. (Note: It Should have Low or No VOC as per Green Building guidelines)

Providing & Fixing finished brass hanging type floor door stopper with necessary screws etc complete.

Providing and laying vitrified floor tiles in different sizes (thickness tobe specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete i.e Size of tile 600x600 mm ( Kajaria/Somany/Cera or Any approved Brand as per Engineer In charge)

Kota stone slab 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm ( average) thick cement mortar 1:3 (1 cement:3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing, polishing and curing complete.

Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.

P/F 1st quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacturer) of approved make in colours, shades except burgundy bottle green, black of any size as approved by engineer-in-charge in Skirting, risers of steps, and dados, over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 course sand) and jointing with grey cement slurry @3.3kg/sqm including pointing the joint with white cement and matching pigments etc., complete.

THERMAL INSULATION

Providing wood work in frames of walls,false ceiling, partitions etc. sawn and fixed in position :Second class kail wood

Providing and fixing 12 mm thick tongued and grooved Pine wood (Soft Wood ) 4-5 inch in width panelling or wall panels in walls and celing includining all necessary fixtures including cornice with necessary screws, priming coat on exposed surface etc., complete. Brand - Rait Wood

Preparing newly prepared panneled surface for polishing by way of filling of putty , sealer and sand papering rubbing and applying hard polish,glossy polish in sequance over the prepared surface complete job

Providing and fixing thermal insulation with specified wool and density conforming to IS: 8183, 50 mm thick, wrapped in 200G Virgin Polythene bags fixed to walls with screws, rawl plugs and washers and held in position by criss-crossing GI wire etc. complete as per directions of Engineer-in-charge. With resin bonded rock wool with density 48 kg/cum

Providing and fixing 50 mm thick extruded polystyrene rigid insulation board of required size underdeck on ceiling surface, complying with ISO 4898:2008 & ASTM C 578-08b - type VI, having thermal conductivity of 0.0289 W/m K as per ASTM C 578 (measured as per IS 3346), compressive strength of> 350 kPa listed as per ASTM D 1621, density of 34-36 kg/cum as per ASTM D 1622, water absorptions < 1% by volume as per ASTM D 2842, oxygen index of 24.1 to 28.1 listed as per ASTM D 2863, cell size 0.4 mm of dia(max) as per ASTM D 3576. Fire retardant property as per DIN 4102, Part 1 of class B2 and as per ASTM E84 class A, fixed with suitable water based adhesive and fastener, complete in all respect as per the direction of Engineer-in-Charge. AREA With Type SE-Self Extinguishing type 50 mm thick

Providing and Fixing Wooden planking, tongued and grooved in flooring including fixing with iron screws complete. 25mm thick Second class teak wood

Providing corrugated G.S sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen nd G.I limpet washers or with G.I lmpet washer filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlappong of sheets complete (upto any pitch in horizontal/vertical or curved surface) excluding the cost of purlins, rafters and trusses and including cutting to size and shape whereever required. (0.63mm thick with zinc coating.)

Providing of fabricated steel roofing truss, purlins, rafters, posts, plates ISA.65x65x6mm ,ISA.50x50x6mm, 40x40x6mm, ISMC 75mm ,65mm,50mm,Plates 8mm,10mm thick, including cutting hoisting fixing in position and applying a priming two or more coat of approved steel priming/painting all work complete job. including launching of trusses. (Steel truss @ 3.5kg/sft)

Design Supply and installation/Fixing staircase railling of stainless steel (Grade 304) railing(Top Handrail Dia > 50mm , two number intermediate Horizontal tubes Dia >25mm and Rectangular Two Pair Balusters Dia >38mm @1000mm C/C) made of Hollow tubes channels, plates etc. including welding ,grinding, buffing, polishing and making curvature (wherever required) including fixing the railing with necessary accessories , newal post , balusters and stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, necessary screws/fixtures complete job as approved by engineer incharge (Note : No additional payment shall be made to master pillar/Newal Post )

Design Supply and installation/Fixing stainless steel SS-304 Grade wall mounted handrail 40-45mm in dia including wall brackets at a spacing of 1.2m-1.5 with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size, along staircase wall , corridors with suitable arrangement as per drawings and approval of Engineer-in-charge

Providing and fixing white vitreous china pedestal type water closet (European type W.C . .pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern including flush pipe with manually controlled device (handle lever) conforming to IS:7231, with all fittings and fixtures, complete including cutting and making good the walls and floors wherever requied:

W.C. pan with lSI marked white solid plastic seat and lid. JAGUAR/CERA Make

Providing and fixing water closet squatting pan ( Indian type W.C. pan) with 100 mm sand cast Iron P or Strap, 10 litre low level P.V. C. flushing cistern including flush pipe (of approved make) "manually controled device (handle lever) conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. (Note : It should have flush rate of with Flush rate of 4/2 Litre per Flush or less ) (Dual flush 4/2L WC cistern with bottom inlet for compact back to wall Rimless toilet)

Orissa pattern white vitreous china W.C. pan of size 580x440 mm with integral type foot rests. JAGUAR/CERA Make

White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps JAGUAR / CERA/HINDWARE Make

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the wallsand floors wherever required : Single half stall urinal with 5 litre P.V.C. automatic flushing cistern

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-Charge and finished smooth. 16mm thick Granite Stone of approved shade

Providing and fixing Stainless steel SS-304 Grade L Shaped 90° Wall Mounted Grab bars Near EWC (European Water Closet) of approved brand for Disable-friendly Bathroom/Toilets as per standard and specification.

Providing and fixing Stainless steel SS-304 Grade Foldable Grab bar For Disable-friendly Bathroom/toilets Make: Jaquar/ Equivalent per standard and specification.

Providing and fixing Salem Stainless Steel A lSI 304 (18/ 8) kitchen sink as per I.S. 13983 with C.l. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required: Kitchen sink with drain board 510x1040mm bowl depth 250mm

P/F of mirrors of superior glass (of approved quality) and of required size and shape. With 6mm thick hard board backing. Rectangular 1500 x 450

15 mm C.P. brass ABS Health Faucet Jet Spray with Hose and Holder of approved quality conforming to IS standards ( KOHLER/JAGUAR/CERA)

Providing and fixing soil waste & vent pipe (Prince or any other appoved brand as per Engineer In Charge

PVC Pipe. 110mm dia (10 feet unit Length)

PVC Pipe. 75mm dia (10 feet unit Length)

PVC Bend 110mm dia

PVC Bend 75mm dia

PVC Tee 110mm dia

PVC Tee 75mm dia

PVC Collar 110mm dia

PVC Collar 75mm dia

PVC trap 110mm dia

PVC trap 75mm dia

PVC Socket 110mm dia

PVC Socket 75mm dia

PVC door junction 110mm dia

PVC door junction 75mm dia

Providing and fixing 3 layer Thermex Pipe PP-R (Poly propylene Random copolymer)pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-incharge.Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including all fittings and cutting chases and making good the wall etc.

PN-16 pipe , 25mm OD(SDR-7.4)

PN-16 pipe , 32mm OD(SDR-7.4)

P/F CP brass toilet paper holder including cost of wodden,PVC,play etc.

Providing and fixing Wall mount Liquid Soap Dispenser of approved brand

Providing and fixing accessories of standard and quality make of approved manufacturer including all necessary fixtures required.

AL-Drops for room door

T Bold for Doors

T Bold for Windows

Handles for door

Handels for window

Providing and Fixing Handles with lock system of main doors LAPO Premium Rose Mortise Door Lock Handle Set/ Mortise Lock with Brass Lock Body and 70mm Brass Cylinder Set with 3 Brass Computer Keys / Zinc Alloy Weather Proof (Matt Finish) or Godrej Locking Solutions and Systems Gloria Antique Brass Door Handle with Lock Set 2C for Home and Office Entrance Door (200 mm, Gold) or any other approved brand as per engineer incharge

15 mm C.P. brass tap with elbow operation lever of approved brand and manufacture

15 mm C.P. brass 2 in 1 tap of approved quality conforming to IS standards

15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931

15 mm nominal bore C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms

C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-incharge.

15 mm nominal bore of standard back type C.P. brass close hole basin mixer pillar tap of approved quality and make, weighing not less than 1.970 kg.

High water pressure S.S geyser connection pipe (2 feet long) of approved quality and make,

Supply installation testing and commissioning of Geyser 50ltr Capacity horizontally mounted of approved brand (Havells/Bajaj/Crompton or any othet approved brand as per engineer in charge including all fixtures , bolts all complete

Supply, Installation, testing and commissioning of 500 liter ETC (Evacuated Tube Collector) based solar water heaters (Cost includes Cold Water Tank, Hot Water Tank, support structures, heat exchanger, electrical backup and installation and commissioning at site. Additional piping will be charged as per actual.

Providing and installation of PUF (Puf Insulated Tanks) water tank capacity 1000 ltrs of approved brand (SYNTEX OR ANY OTHER APPROVED BRAND) as per direction engineer incharge

Supply and installation of High Quality self regulating heat tracer for Specialized Heating Solutions for Winterisation of water pipeline including all accessories complete including Supply and installation of Circuit Control Panel with RCBO MCB ,THERMOSTAT (0-120) DEG C, power connector-two way-6 sq.mm, w.p. splice connector,w.p. tee connector,end seal,mounting kit-w.p. jb,g.i. pipe strap 4",al. adhesive tape roll ( 50 mm w x 20 m l),f.g. adhesive tape roll (DANFOSS Make OR CHROMALOX any other approved brand as per the direction of Engineer-In-Charge)

Supplying and fixing High Quality 32mm Thick Nitrile Insulation Tube for water pipeline of approved brand 2 Inch Size (Armaflex Class-o Armacell) including alumunium duct clading of approved quality and finish as per the direction of engineer in charge

Suppy and installation of 6 - 8 Inch Dia alumunium suction Duct Pipe (Alumunium Sheet Guage Thickness = 0.46MM TO 0.71MM ) For HVAC Ducting for kitchen baths including stainless steel Clamps and all necessary fixtures all complete

Supply and installation of Reflective Bubble Aluminum Foil Insulation / Aluminium Silver Bubble Sheet 210 GSM (7 mm) Thick Light Weight Reflective Insulation , Max Withstanding Temperature -40 degree To +110 Degree Waterproof insulation all complete

Supply and installation of electrical Underfloor heating mats for floor heating systems non-corrosive, flexible heating elements including cables, pre formed cable mats including smart thermostat and digital electrical control panel all complete (STIEBEL ELTRON / DANFOSS Or any other approved brand

Provision for providing and fixing ornamental Shingstak (Ladakhi wood carving over exterior Windows and main entrance door) (Design as per the direction of Engineer-In-charge.) including polishing all complete

SITC Stainless Steel Water Purifier & Dispenser 20ltr Filtered Warm & Cold water (455 x 450 x 1370 mm) of approved brand (CONVEY/KENT/BLUESTAR OR equivalent)

Supplying & fixing of retro reflective sign board of size 1800 mm x 1200 mm. The board made of High intensity prismatic grade type IV retro reflective sheeting of 3M /Avery Denison or equivalent make approved by I.R.C. / M.O.S.T. with message and graphics to be overlay film of same make duly plotter cut, letters written (both side) in white colour, to be pasted on 3mm thick ACP sheet of make Alstone / Alstrong / Eurobond / Alucobond or equivalent. Frame made of 38mm dia pipe & 2nos. 63mm diavertical posts, 3 Mtr. high, all made of 304 series (Jindal or equivalent) stainless steel. Pipe fixed on ground including necessary excavation and sign board fixed with in ground in 600 mm depth with all excavation & cement aggregate concrete 1 : 2 : 4 {1 cement : 2 coarse sand : 4 graded stone 20 mm nominal size) as per direction of Unit Incharge.

Supplying & fixing of retro reflective sign board of size 1200 mm x 900 mm. The board made of High intensity prismatic grade type IV retro reflective sheeting of 3M /Avery Denison or equivalent make approved by I.R.C. / M.O.S.T. with message and graphics to be overlay film of same make duly plotter cut, letters written (single side) in white colour, to be pasted on 3mm thick ACP sheet of make Alstone / Alstrong / Eurobond / Alucobond or equivalent. Frame made of 40mm dia pipe & 2nos. 63mm diavertical posts, 2.10 Mtr. high, all made of 304 series (Jindal or equivalent) stainless steel. The pipe shall be standing on hard concrete surface with the help of SS holdfast/ Hilti or equallent flush anchor (Fasteners) of as per required size and numbers and thickness and nut bolts on 02 Nos.5 mm thick 200mm x 200 mm size SS plate welded with 63mm dia SS pipe as per direction of Unit Incharge.

Supply & Fixing signages for exit of size 375mm x 200mm x 8mm in acrylic sheet LED light with battery backup

Supply & Fixing Display notice pin up board or white writing board of required size, aluminum beeding of 12 mm and fixed with required numbers of rawls plugs stainless steel srew as per direction of Unit Incharge.

Supply and fixing of Amuminium Silver powder coated signage of required size complete with message. Matter will be digital print written single sides, matter covered with transparent polycarbonate sheet 0.5mm. and duly fixed with required nos of rawls plugs stainless steel srew/ double side tape of 3M make/ screw required nos of holes, wherever required complete as per direction of Unit Incharge

Providing & fixing of emergency sign boards single side of required size made of Phot luminescent film having glow power of 4 hours with message and graphics to be screen printing / vinyl cut film of 3M / Avery Denison / LG / Oracle or equivalent make to be pasted on 3mm thick Sun Board sheet all complete and duly fixed with required numbers of rawls plugs stainless steel srew/ double side tape of 3M make required nos of holes, wherever required complete as per direction of Unit Incharge

Providing & fixing of emergency sign boards single side of required size made of Phot luminescent film having glow power of 4 hours with message and graphics to be screen printing / vinyl cut film of 3M / Avery Denison / LG / Oracle or equivalent make to be pasted on 3mm thick Sun Board sheet all complete and duly fixed with required numbers of rawls plugs stainless steel srew/ double side tape of 3M make required nos of holes, wherever required complete as per direction of Unit Incharge

12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard manufactured from natural gypsum as per IS 2095 part-I and laminated with white 0.16mm thick fire retardant PVC film on the face side and 12micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit.

SEPTIC TANK

Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres: as directed by Engineer-in-charge. Note :Stockpile the top layer of soil of 200 mm and cover it for reuse in landscape (If soild is fertile or capable to make it fertile), soil test to be performed from ICAR Lab as per green Building Guidelines

ORDINARY ROCK=80%

ALL KIND OF SOIL=20%

Disposal of Mulba/Excavated Earth Beyond 50m (Lead upto 6Km) Outside Campus Area (CARRIAGE OF MATERIALS By Mechanical Transport including loading, unloading and stacking)

Providing and laying position cement concrete of specified grade excluding the cost of centering and shuttering. All work upto plinth level 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) (crushed) Mud Mate (Use Of Portland Pozzolana Cement Is advised as Per Green Building Guidelines OR 25% replacement of Ordinary Portland cement with fly ash by weight of cement used in structural concrete.)

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 ( 1 cement : 6 course sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with cement mortar 1:6 ( 1 cement : 6 course sand) and curing complete (Quarry Stone)

Dry random rubble masonary with hard stone in foundation & plinth using quarry stone with bond stone

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) (Use Of Portland Pozzolana Cement Is advised as Per Green Building Guidelines OR 25% replacement of Ordinary Portland cement with fly ash by weight of cement used in structural concrete.)

Providing & fixing upto floor five level precast cement concrete solid blocks including hoisting and setting in position in cement mortar 1:3 (1cement:3 coarse sand), cost of required centring, shuttering and curing complete 1:2:4 (1 cement : 2 coarse sand : 4 graded crushed stone aggregate 20 mm nominal size) (Use Of Portland Pozzolana Cement Is advised as Per Green Building Guidelines OR 25% replacement of Ordinary Portland cement with fly ash by weight of cement used in structural concrete.)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering and shuttering including strutting, propping etc. and removal of form for:

Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete.50 mm thick with 20mm nominal size stone aggregate. (Use Of Portland Pozzolana Cement Is advised as Per Green Building Guidelines OR 25% replacement of Ordinary Portland cement with fly ash by weight of cement used in structural concrete.)

SEPTIC TANK 50 mm thick with 20mm nominal size stone aggregate.

Supplying and fixing C.I. cover without frame for manholes: 560 mm diameter C.I. cover ( heavy duty) the weight of the cover to be not less than 108 kg

CEMENT PLASTER (IN COARSE SAND) 12mm Cement plaster of mix 1 : 4 ( 1 cement : 4 coarse sand) (PPC or cement with >25% flyash is recommended as per green building guildelines)

Carriage differncen materail from source to site of work including loading un loading and stacking complete job

stone for an averge 43Km MT

sand/Bajree for an averge 05 Km MT

cement /Steel 2Km by MT