CAD work to Flow Irrigation Scheme Rai,Di,Kuhal in Tehsil Palampur Distt. Kangra HP SH,Construction of Kisan Bhawan

Amount

Excavation in foundation trenches etc.( for pipes and pits)up to all depths in all kind of soil such , as pick work, jumper work saturated soil including bailing or pumping out water, blasting soft/hard rock or chiselling soft /hard rock where blasting is prohibited in all leads & lifts including triming & dressing of sides levelling of beds to correct grade including shorting struttering planking timbering and dewatering where ever required stacking usable/unusable material / soil separately and after laying jointing and testing of pipes returning the usable soil in trenches in 15cm layers including consolidating of such deposited layer by ramming & watering & then disposing of all surplus excavated earth as directed with in all leads & lifts including restoration of unmetalled surfaces to its original condition & including cost of a diversion for traffic night signals,fixing caution boards crossing over trenches for access to houses fencing etc. as per direction of Engineer-in-Charge with in all leads and lifts.

Providing & Laying cement concrete 1:4:8 ( 1 cement :4 approved sand :8 approved graded stone aggregate 40mm nominal size ) & curing complete excluding the cost of form work in foundation and plinth as per direction of Engineer-in-Charge with in all leads and lifts.

Providing and laying cement concrete work 1:1/1/2:3 (1 cement: 1/1/2 sand: 3 graded stone aggregate 20 mm nominal size) and curing complete excluding cost of from work and reinforcement for reinforced concrete work in.

Foundation footing bases of columns etc.and like the mass concrete as per direction of Engineer-in-Charge with in all leads and lifts.

Colunms pillars posts and struts upto floor two level. as per direction of Engineer-in-Charge with in all leads and lifts.

Lintels, beams girders bressumers and cantilevers upto floor two level.as per direction of Engineer-in-Charge with in all leads and lifts.

Providing & Laying cement concrete 1:2:4 ( 1 cement :2 approved sand :4 approved graded stone aggregate20mm nominal size ) & curing complete excluding the cost of form work and reinforcement for reinforced concrete work in

Suspended floor roofs,landing and shelves and their support balconies,beams,girders,bressumers and cantilever upto floor two level as per direction of Engineer-in-Charge with in all leads and lifts.

Stair cases (Except spiral stair cases) excluding landing but including preparing of the surface and finishing of nosing upto floor two level. as per direction of Engineer-in-Charge with in all leads and lifts.

Providing, Laying mild or tor steel reinforcement for RCC. Work including bending binding and placing in position complete upto floor two level Tor steel in all leads and lifts.

Providing form work with steel plates 3.15milimetres thick welded with angle iron in frame 30x30x5 mm, so as to give a fair finish including centring, shuttering ,strutting and propping etc. with wooden battens & ballies, height of propping & centring below supporting floor to ceiling not exceeding 4.00 metres & removal of the same for in situ - reinforced concrete & plain concrete work in :-

Vertical surfaces such as walls(any thickness) partitions and the like including attached pilasters, buttresses, plinth and string courses and the like complete in all respect as per direction and to the entire satisfaction of the Engineer-in-charge.

Flat surfaces such as soffits & suspended floors,roofs and the like complete in all respect as per direction and to the entire satisfaction of the Engineer-in-charge.

Columns, pillars, post and struts Square, rectangular or polygonal in plan complete in all respect as per direction and to the entire satisfaction of the Engineer-in-charge.

Sides and soffits of beam, beam haunching, cantilever, bressumers and lintels not exceeding 1 mtr. In depth in all heights from floor complete in all respect as per direction and to the entire satisfaction of the Engineer-in-charge.

Edges of slab and breaks in floors and walls under 20 cm wide. complete in all respect as per direction and to the entire satisfaction of the Engineer-in-charge.

Stair cases with sloping or stepped soffits excluding landings. complete in all respect as per direction and to the entire satisfaction of the Engineer-in-charge.

Foundation footing bases of columns etc and mass concrete complete in all respect as per direction and to the entire satisfaction of the Engineer-in-charge.

Random Rubble Masonry / polygonal rubble masonry (uncoursed / brought to courses) with hard stone of approved quality in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 sand : 12 graded stone aggregate 20 mm nominal size) at plinth level in cement mortor 1:6 ( 1 cement : 6 sand) as per direction of Engineer-in-Charge with in all leads and lifts.

Steel work welded in built up sections, trusses and framed work including cutting hoisting Fixing in position and applying a priming coat of red lead paint :-

In trusses and trussed purlings in buildings as per direction of Engineer-in-Charge with in all leads and lifts.

Providing & Fixing 0.60 mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coatig including Fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia metre with prepainted limpet and rubber washers complete with all accessories as required as per the direction of Engineer-in-charge.

Providing ridges or hips 60 cm over all in plain with galvanised iron prepainted steel Sheet fixed J or L hooks bolts and nuts 8mm dia G.I Limpet and bitumen washers complete 0.60 mm thick sheet as per direction of Engineer-in-Charge with in all leads and lifts.

Providing and Fixing 15 cm wide 45 cm over all semicircular with iron plain G.I. sheet gutter with iron brackets 40x3mm size bolts and nuts and washers etc. including making necessary connection with rain water pipe complete as per design. 0.80 mm thick sheet. as per direction of Engineer-in-Charge with in all leads and lifts.

Provdiing and laying 20 cm thick composit stone masonry with stone masonry with stone facing of chisel dressed stone one line dressed in cement mortar 1:6 (1 cement :snnd) and concrete backing with cement concrete 1:3:6 (1cement :3and :6 graded stone aggregate 20 mm norinal size) on inner face of walls including cenrting shuttering and propping complte upto floor two level as per direction of Engineer-in-Charge with in all leads and lifts.

Brick work using common burunt clay building bricks in super structure above plinth level upto floor two level in cement mortor 1:6 (1 cement : 6 sand) (Ist class brick) as per direction of Engineer-in-Charge with in all leads and lifts.

Half bricks masonry in common burnt clay building bricks in cement mortar 1:4 (1cement : 4 sand) (Ist class brick) as per direction of Engineer-in-Charge with in all leads and lifts.

Providing wood work in frames of doors, windows, clerestory windows and other frames wrought, framed and fixed in position. (2nd class Indian Teak Wood) as per direction of Engineer-in-Charge with in all leads and lifts.

6mm cement plaster to ceiling in CM 1:3 ( 1 Cement : 3 Sand) as per direction of Engineer-in-Charge with in all leads and lifts.

15 mm cement plaster in single coat on rough side of brick/concrete stone walls for interior plastering up to floor two levels including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80 mm in girth and finished even and smooth in cement mortar 1:5 (1 cement: 5 sand) as per direction of Engineer-in-Charge with in all leads and lifts.

20 mm thick cement plaster in single coat on rough side of brick/stone/concrete walls for interior plastering up to floor two level including arrisses, internal rounded angles, chamfers and or rounded angles not exceeding 80 mm in girth and finished even and smooth with in all leads and lifts in C.M 1:3 ( 1 cement : 3 sand ) as per direction of Engineer-in-Charge with in all leads and lifts.

Stone soling under flooras per direction of Engineer-in-Charge with in all leads and lifts.

Providing and laying cement concrete 1:6:12 (1 cement : 6 sand : 12 graded stone aggregate 40 mm nominal size) and curing complete excluding the cost of form work in foundation and plinth as per direction of Engineer-in-Charge with in all leads and lifts.

Providing and laying granite stone in flooring 20mm (average) thickness base of cement mortor 1:3 (1cement : 3sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone including rubbing and polishing complete. 20 mm thick as per direction of Engineer-in-Charge with in all leads and lifts.

Providing and laying Duro stone vetrified tiles 300x300x10mm in grey/coloured or of approved shade in flooring, treads of steps and landing laid on a bed of 12 mm thick cement mortor 1:3 (1 cement : 3 sand) laid over and jointed with neat cement slurry flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete as per direction of Engineer-in-Charge with in all leads and lifts.

Providing and laying vetrified double charge tiles 600x1200x10mm in grey/coloured or of approved shade in flooring, treads of steps and landing laid on a bed of 12 mm thick cement mortor 1:3 (1 cement : 3 sand) laid over and jointed with neat cement slurry flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete as per direction of Engineer-in-Charge with in all leads and lifts.

Providing and Fixing antiskid water proof stain and impact resistent heavy duty vetrified tiles Nitco or equivelent (300 X 300 X 10 mm) manufactured of approved shade and colour treads of steps laid on a bed of 12 mm thick cement mortor 1:3 (1cement : 3 sand) finished with flush pointing in white cement mixed with pigment ofrequired shade to match the shade of tiles complete as per direction of Engineer-in-Charge with in all leads and lifts.

Coloured glazed tiles 6 mm thick (300x450 mm) in skirting risers of steps and dedo12 mm thick cement mortar 1:3 (1 cement : 3 sand) and jointed with cement slurry in all leads and lifts.

Providing and Fixing panneled glazed or panelled and glazed shutters for doors, windows and clerestory windows,including black enamelled iron butt hinges with necessary screws. 40 mm thick. (2nd class indian Deodarwood) as per direction of Engineer-in-Charge with in all leads and lifts.

Providing and Fixing wire gauge shutters using galvenised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm for doors, windows & clearstory windows i/c bright finished black iron enamelled hinges with necessary screws 40 mm thick (2nd class indianDeodar wood) as per direction of Engineer-in-Charge with in all leads and lifts.

Providing & Fixing M.S. grills of required pattern in wooden frame of window etc.with M.S. flats, square or round barswith round headedbolts and nuts by screws (ornamental grills) as per direction of Engineer-in-Charge with in all leads and lifts.

Providing 40x3 mm iron hold fast 40 cm long including fixing to frame with 10 cm da bolts nuts and wooden pluges and embencing in C.C. block 30x10x15 cm 1:3:6 ( 1 cement:3 sand: 6 graded stone aggregate 20 mm nominal size). as per direction of Engineer-in-Charge with in all leads and lifts.

Providing and fixing bright finished Steel sliding door bolts with bolts and nuts screws etc. completeas per direction of Engineer-in-Charge with in all leads and lifts.

Providing and fixing bright finished steel tower bolts ( barel type) with screws etc. Complete as per direction of Engineer-in-Charge with in all leads and lifts.

Providing and fixing bright finished steel handles with necessary screws etc. Complete as per direction of Engineer-in-Charge with in all leads and lifts.

Providing and Fixing bright finishaed hard drawn Hooks and Eyes 250 mm as per direction of Engineer-in-Charge with in all leads and lifts.

Providing and Fixing of Block Board (Bhutan/Green Make) (Medium Density Fiber Board) Pre Laminated wooden Cup Board of size 19 mm. anti termite and dampness proof including all materials and fittings etc. in all leads and lifts as per the entire satisfaction of the Engineer - in - Charge.

Providing plinth protection 50 mm thick in cement concrete 1:3:6 (1cement:3sand:6 graded stone aggregate 20 mm nominal size as per direction of Engineer-in-Charge with in all leads and lifts.

Proving under layer for plinth protection of 75 mm thick (unconsolidated) bed dry brick/stoneAggregated 40 mm nominal size will rammed with rammed and consolidated and grouted with fine sand including preparation of ground as per direction of Engineer-in-Charge with in all leads and lifts.

Constructing course rubble hammer dessed "U" shape open surface drain with side wall 15x22 cm in cement mortor 1:6 (1cement : 6 sand) and inside plastering with cement plaster 1:3 (1cement : 3 sand) including earth work and laayng 10 cm cement concrete in 1:5:10 (1 cement :5 sand : 10 graded stone aggregate 40 mm nonminal size) and 7.5 cm cement concrete 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 20 mm nominal size) and finished with a floating coat of neat cement complete as per standard design as per direction of Engineer-in-Charge with in all leads and lifts.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete as per direction of Engineer-in-Charge with in all leads and lifts.

Applying one coat of Acrylic primer (Spectrum or equivalent of Superior quality) on new concrete / masonry / plastred surfaces after and including preparing the surface by thoroughly brushing the surface free from mortar droppings and other foreign matters, sand papering the surface smooth complete as per direction of Engineer-in-Charge with in all leads and lifts.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equivalent on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc. including sand paper smooth completeas per direction of Engineer-in-Charge with in all leads and lifts.

Wall painting (two coats) with acrylic emulsion paint of approved brand and manufacture for interior grade on undecorated concrete / stone / plastered wall surfaces to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty a required for metling the surface as per direction of Engineer-in-Charge with in all leads and lifts.

Applying one coat for wood preservetive on previously treated wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter,sand papering and knotting as per direction of Engineer-in-Charge with in all leads and lifts.

Applying priming coat over new wood and wood based surfaces after and inciuding preparing the suface be thoroughly cleaning oil grease dirt and othr foreign sand papering and knotting Readymixed paint brushing wood primer pink as per direction of Engineer-in-Charge with in all leads and lifts.

Painting two coats (excluding priming coat) on new wood and wood based surfaces with enamel paint to give an even shade including cleaningthe surface of dirt, dust and other foreign matters sand papering and stopping with enamel paint other than white as per direction of Engineer-in-Charge with in all leads and lifts.

Providing & Fixing Stainless Steel Railing of 304 grade (ISI) of approved brand complate in all respect in all leads and lifts.

Manufacturing and fixing of cup board made with ply board 19 mm thick of Anchor,Kit GMS make including all fitting such as hings,handels,magnetic catcher and sliding channel etc.The exposed portion of the cup board shall be provided with mat finish sunmica not less then 1 mm in thickness pasted with favicol.The door and exposed edges shall be provided moulding to give the cup board decorative look as directed by engineer incharge.The cup board shall be painted with two coats of white paint in side.The entire work should be as per direction/satisfaction of Engieer in Charge.

Wiring for light point / fan point / exhaust fan / call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required. Group "C" as per direction of Engineer-in-Charge with in all leads and lifts.

Light Point

Fan Point

Exhaust Fan,point

Wiring for light plug with 2x1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No.1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required complete.as per direction of Engineer-in-Charge with in all leads and lifts.

Supplying & Fixing of G.I. modular boxes of following sizes along with modular base and cover plate for modular switches in recess as required as per direction of Engineer-in-Charge with in all leads and lifts.

4 modules (140mmx78mmx50mm)

6 modules (205mmx78mmx50mm)

8 modules (120mmx135mmx60mm)

Wiring for circuit/sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No. HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required complete.as per direction of Engineer-in-Charge with in all leads and lifts.

2 x 1.50 Sq. mm.

2 x 2.50 Sq. mm.

2 x 4.00 Sq. mm.

Wiring for circuit / sub-main with 4x6 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 2 No.6 Sq.mm. (4x6+2x6) HRFRLS/PVC insulated single core copper conductor cable for earthing as required complete.as per direction of Engineer-in-Charge with in all leads and lifts.

Supplying and Fixing following rating Modular switch /socket in the existing switch box / cover plate including connections etc. as required complete.as per direction of Engineer-in-Charge with in all leads and lifts.

S.P. 5/ 6 Amps one way Modular switch.

5 pin, 5/ 6 Amps Modular socket outlet.

Bell push, Modular

Supplying and Fixing following rating Modular switch /socket in the existing switch box / cover plate including connections etc. as required. as per direction of Engineer-in-Charge with in all leads and lifts.

S.P. 15/ 16 Amps one way Modular switch. Item 912

6 pin,15/16 Amps Modular socket outlet

Supplying and Fixing following rating Modular switch /socket in the existing switch box / cover plate including connections etc. as required. as per direction of Engineer-in-Charge with in all leads and lifts.

TV. Socket outlet, modular

Supplying and Fixing following rating Modular switch /socket in the existing switch box / cover plate including connections etc. as required. as per direction of Engineer-in-Charge with in all leads and lifts.

Telephone socket outlet, Modular.

Supplying and Fixing ceiling rose on the existing junction box / wooden block including connections etc. as required complete.as per direction of Engineer-in-Charge with in all leads and lifts.

Double door-12 way

Supplying and Fixing following rating, four pole (three phase & neutral) 415 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 miliampers in the existing MCB DB complete with connections, testing and commissioning etc. as required. as per direction of Engineer-in-Charge with in all leads and lifts.

63 Amps. Cat-A.

Supplying and Fixing sheet metal bus-bar chamber suitable for 200 Amp. 415 volts capacity with 4 No. copper strip bus-bars each of length 450 mm & cross-sectional area (25.4 mm x 4.75 mm), enclosure made from 1.6 mm thick M.S. sheet having overall dimensions (530 mm x 450 mm x 150 mm) nominal with all accessories including connections, earthing the body etc. as required complete.as per direction of Engineer-in-Charge with in all leads and lifts

Providing and Fixing TP&N switch disconnector fuse unit cubical type, 415/500 volts with 3 No. HBC/HRC fuses, in sheet steel enclosure including drilling holes on the board, connections, earthing the body etc. as required.as per direction of Engineer-in-Charge with in all leads and lifts.

100 Amp. Category-A

Earthing with copper earth plate 600 mmx600 mmx 3 mm thick, including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. ( but without charcoal or coke and salt ) complete as required complete.as per direction of Engineer-in-Charge with in all leads and lifts.and lifts.

Extra for using salt and charcoal for G.I. or copper plate earth electrode complete as required.item no. 1906 as per direction of Engineer-in-Charge with in all leads and lifts.

Providing and Fixing M.V.danger notice plate of 200 mm x 150 mm made of mild steel at least 2 mm thick, and vitreous enameled white on both sides and with inscription in signal red color on front side as required. Item no2101 as per direction of Engineer-in-Charge with in all leads and lifts.

Providing and installation of stationary storage type Electric water heater (Geyser) of various sizes by means of Expansion-bolts with nuts and washers, including embedding of expansion-bolts in the wall, providing and Fixing of Non-return valve, Dead weight safety valve, 2 No C.P. connection rods 18" long, making good the damages, electrical connections, safety valve connections, testing and commissioning etc. as required.as per direction of Engineer-in-Charge with in all leads and lifts.

25 Liter capacity water heater (Cat-A)

10 Liter capacity water heater (Cat-A)

Providing, Installation, testing and commissioning of ceiling fan with regulator, including wiring the down rods of standard length (up to 30 cm) with 16/0.20 mm twin twisted flexible, cotton braided, copper cable, including providing and Fixing phenolic laminated sheet cover on the fan box and earthing etc. as required. as per direction of Engineer-in-Charge with in all leads and lifts.

Ceiling Fan 1400 mm sweep, Category-A

Providing and installation of exhaust fan of following sizes in the existing opening, including making the hole to suit the size of the above fan, making good the damages, connections, testing and commissioning etc. as required.as per direction of Engineer-in-Charge with in all leads and lifts.

Exhaust Fan, Light duty, (Domestic) 225 mm sweep

Providing and Fixing of Syska make LED Tube Fixture 18 watt complete in all respect in all leads and lifts.item no. 920as per direction of Engineer-in-Charge with in all leads and lifts.

Supplying and Fixing Ding-Dong / Electronic musical bell, suitable for D.C./A.C. single phase,230 volts complete as required complete.as per direction of Engineer-in-Charge with in all leads and lifts.

Supplying and drawing co-axial TV cable,RG-6 grade,0.7mm (75 Ohms) copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface / recessed, steel / PVC conduit as required complete.as per direction of Engineer-in-Charge with in all leads and lifts.

Supplying and Fixing bakelite batten/angle holder including connections etc. as required complete as per direction of Engineer-in-Charge with in all leads and lifts.

Supplying and Fixing of integral CFL Post Top Lantern of following capacity, cast aluminium spigot, spun aluminium canopy, opal acrylic diffuser, complete with all accessories but excluding CFL lamp including making connections, testing etc. as required.

Gate post top lantern - CFL 26 watt

Spplying and Fixing of split type air conditioner Blue Star / LG / Onida Whirlpool / Lioyd / Samsung make having three stars features auto clean filter four way swing all copper pipes including making provision of draining of back moisture water tharough GI pipe 20 mm dia electronic voltage stabilizer, cutting holes for conduits in wall, unit bracket set fixed on outer wall complete as required. 1.50 Tonne capacity. as per direction of Engineer-in-Charge with in all leads and lifts.

Providing and Fixing of Water Cooler makes of reputed make i.e. USHA/ Voltas / Blue Star etc. having capacity of 40 liters in all leads and lifts

Providing and Fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including Fixing with approved adhesive etc. complete.as per direction of Engineer-in-Charge with in all leads and lifts.

75 mm dia

110 mm dia

Providing and Fixing PVC plain bend ISI marked including Fixing with approved etc. complete.as per direction of Engineer-in-Charge with in all leads and lifts.

75 mm dia

110 mm dia

Providing and Fixing PVC door bend with oval access door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including Fixing with approved etc. completeas per direction of Engineer-in-Charge with in all leads and lifts.

75 mm dia

110 mm dia

Providing and Fixing PVC collars ISI marked including Fixing with approved etc. Complete as per direction of Engineer-in-Charge with in all leads and lifts.

75 mm dia

110 mm dia

Providing and Fixing PVC singal equal branch plain ISI marked including Fixing with approved etc. completeas per direction of Engineer-in-Charge with in all leads and lifts.

110 mm dia

Providing and Fixing PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm thick bolts and nuts complete including Fixing with approved etc. complete.as per direction of Engineer-in-Charge with in all leads and lifts.

110 mm dia

Providing and Fixing PVC floor trap ISI marked of self cleaning design including Fixing with approved, cost of cutting and making good the wall and floors etc. complete.as per direction of Engineer-in-Charge with in all leads and lifts.

Kitchen 110mmx90 mm

110 mm x 90 mm.

Providing and Fixing vitreous China wash, down water closet (EuropeanType WC pan) with integral "P" or "S" trap including jointing the trap with soil pipe in cement mortar 1:1 (1 cement : 3 sand) ( seat and cover to be measured and paid for seperately) : Anglo Indian (Universal Closet) as per direction of Engineer-in-Charge with in all leads and lifts.

Providing and Fixing white solid type plastic sheet and cover for wash down water closet with CP brass hinges and rubber buffers.as per direction of Engineer-in-Charge with in all leads and lifts.

Providing and Fixing 10.00 liters Concealed cistern with a pair of C.I. or mild steel brackets, complete with fitting such as lead valve less syphon, 15 mm nominal size brass ball valve with polythene float, C.P. Brass handle, Unions and couplings for connections with inlet, outlet and couplings for connections with inlet, outlet and over flow pipes, 40 mm dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately) in all leads and lifts. (HPSR-2020 CODE NO-17.64)as per direction of Engineer-in-Charge with in all leads and lifts.

Providing & Fixing viterious china wash basin with single hole for pillar tap with C.I. or M.S. bracket painted white including cutting hole including good the same excluding fitting Cera sanitary work (cornet) white Flat back 630 mm x 450 mm. as per direction of Engineer-in-Charge with in all leads and lifts.

Providing and Fixing viterious china padestral for wash basin complete recessed at the basic for reception of pipe and fittings Cera sanitary work (carnet) white (Viterious China in White Colour) as per direction of Engineer-in-Charge with in all leads and lifts.

Providing and Fixing G.I. Union for wash basin or sink 32 mm dia. as per direction of Engineer-in-Charge with in all leads and lifts.

Providing and Fixing C.P. brass waste and plug for glazed ware sinks, basins etc. with long screwed shank and fly nut and fixed to steel pipe including vulcanite plug, brass chain and stud 32 mm nominal bore.(HPSR-2020 CODE NO 13.107.1)as per direction of Engineer-in-Charge with in all leads and lifts.

Providing and Fixing 600 mm x 450 mm bevelled edge mirror of superior glass marked on 6mm thick AC sheet or plywood sheet and fixed to wooden plug with CP brass screws and washer.as per direction of Engineer-in-Charge with in all leads and lifts.

Providing and Fixing CP Brass towel rail complete with CP Brass brackets fixed to wooden plug with CP Brass screws 600 mm x 20 mm. as per direction of Engineer-in-Charge with in all leads and lifts.

Providing and Fixing 600 mm x 120 mm glass shelf with C.P. Brass bracket and guard rail complete, fixed to wooden plugs with C.P. Brass screws.as per direction of Engineer-in-Charge with in all leads and lifts.

Providing and Fixing chromium plated brass soap dish with C.P. Brass brackets fixed to wooden cleats with C.P. brass screws.

Providing and Fixing Tooth brush and Tumbler holder (Viterious China)as per direction of Engineer-in-Charge with in all leads and lifts.

Providing and Fixing C.P. Brass Shower Rose with 15 mm to 20 mm inlet 100 mm dia.as per direction of Engineer-in-Charge with in all leads and lifts.

Providing and Fixing brass bib tap (Superior or heavy type) 15 mm dia long nose.as per direction of Engineer-in-Charge with in all leads and lifts.

Providing and Fixing brass bib tap (Superior or heavy type) 15 mm dia short body.as per direction of Engineer-in-Charge with in all leads and lifts.

Providing and Fixing C.P. brass angle valve 15 mm without Nuts and pipe.as per direction of Engineer-in-Charge with in all leads and lifts.

Providing and Fixing Brass Divertor 15 mm of superior qaulity in all leads and lifts.as per direction of Engineer-in-Charge with in all leads and lifts.

Providing and Fixing Kitchen Sink mixture of superior quality complete in all respect in all leads and lifts.

Providing and Fixing wash basin mixture of superior quality complete in all respect in all leads and lifts.

Providing and Fixing P.V.C. connection with brass unions 300 / 450 mm length 15 mm nominal bore.

Providing and Fixing 100 mm dia chromium plated grating of superior quality for floor, gully or Nahni trap as per direction of Engineer-in-Charge with in all leads and lifts.

Providing and Fixing PTMT Jet spray of approved quality and colour with one meter tubeas per direction of Engineer-in-Charge with in all leads and lifts.

Providing and Fixing of C.P. Towel ring of superior quality as per direction of Engineer-in-Charge with in all leads and lifts.

Providing and Fixing of C.P. towel rack 600 mm x 250 mm of superior quality as per direction of Engineer-in-Charge with in all leads and lifts.

Providing and Fixing stainless steel kitchen sink (Double Bowl) of approved standard ISI make with drain board and C.P. waste with C.I. or M. S. brackets painted white including cutting holes and making good the same but excluding fitting 610 x 460 mm with bowl depth 200 mm.

Providing and Fixing to wall ceiling and floor galvenised mild steel tubes (light grade) tube fittings and clamps including making good the wall, ceiling and floor in all leads and lifts.

25 mm nominal bore

Providing and Fixing brass full way valve with wheel of 25 mm dia (Heavy Duty) complete in all respect in all leads and lifts.

Providing and Fixing to wall ceiling and floor KITEC Composite PR Pipes (as per IS 15450:2004) (The pipes are having inner layer in natural colour & outer layer in black colour) and clamps including making good the wall, ceiling and floor complete in all respect in all leads and lifts.

15 mm nominal bore

20 mm nominal bore

Providing and Fixing KITEC Coupler composite crimp fittings-internal sealing of size mentioned below (Heavy Duty) complete in all respect in all leads and lifts.

15 mm dia

20 mm dia

Providing and Fixing KITEC Elbow composite crimp fittings internal sealing of size mentioned below (Heavy Duty) complete in all respect in all leads and lifts.

15 mm dia

20 mm dia

Providing and Fixing KITEC Equal Tee Pcomposite crimp fiitings internal sealing of size mentioned below (Heavy Duty) complete as required complete.as per direction of Engineer-in-Charge with in all leads and lifts.and lifts.

15 mm dia

20 mm dia

Providing and Fixing KITEC Reducing Tee composite crimp fittings internal sealing of size mentioned below (Heavy Duty) complete in all respect in all leads and lifts.

20x15 mm dia

Providing and Fixing KITEC Reducer composite crimp fittings internal sealing of size mentioned below (Heavy Duty) complete in all respect in all leads and lifts.

20x15 mm dia

Providing and Fixing KITEC female threaded connector composite crimp fittings internal sealing of size mentioned below (Heavy Duty) complete in all respect in all leads and lifts.

15 mm dia

20 mm dia

Providing and Fixing KITEC Male threaded connector composite crimp fittings internal sealing of size mentioned below (Heavy Duty) complete.as per direction of Engineer-in-Charge with in all leads and lifts.and lifts.

15 mm dia

20 mm dia

Providing and Fixing KITEC Female Elbow composite crimp fittings internal sealing of size mentioned below (Heavy Duty) complete.as per direction of Engineer-in-Charge with in all leads and lifts.and lifts.

15 mm dia

20 mm dia

Providing and fixing KITEC pipe Holding Clamps with brass plate of approved design with steel screws and rawal plugs etc. Complete as per direction of Engineer-in-Charge with in all leads and lifts.

Providing and Fixing of PVC water storage tank sintex having of capacity 1000 liters with necessary fittings including over flow pipes, scour pipes etc. inlet and outlet and inside paint of required size for inlet or outlet and inside paint of approved quality complete including hoisting complete in all respects as per direction of Engineer-in-Charge with in all leads and lifts.

Shashank Jagota Govt. Contractor

AMIT CHOUDHARY

Sushant Puri