Construction of Science block Additional Accommodation Govt Sen Sec School Bara in Tehsil Chachyot Distt Mandi SH C/o Building portion site development WSSI Septic tank soak pit harvesting system

Amount

Excavation in foundation, trenches etc. in earth work in all kinds of soil such as pick work, Jumper work, blasting work in soft and hard rock, conglomerated rock or saturated soil and its intermediate classification of soil, chieseling work and wedging out rock (where blasting is prohibited) and pumping or bailing out watering/dewatering upto any lift, stacking the excavated soil upto any lead from the edge of excavation and then returning the stacked soil in layer when required into plinth, sides of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earthto the disposal point including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Excavation in soil in hilly area by mechnicial means including cutting and trimming of side slopes and disposing of excavated earth as per technical specification clause 1603.1 + 1603.2. with in all leads and lilfts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Earth work in excavation for structure as per drawing and technical specification clause 305.1 including setting out construction of shoring and bracing removal of stumps and other deletarious material and disposal up to any lead dressing of sides and bottom and back filling in trenches with excavated suitable material ordinary soil including carriage of material with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete. with including carriage of material with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and laying cement concrete 1:6:12 (1 cement:6 sand : 12 graded stone aggregate 40 mm (fourty millimetre) nominal size and curing complete excluding cost of centring and shuttering in foundation and plinth including carriage of material with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing form work with steel plates 3.15mm(Three point fifteen millimeter) thick welded with angle iron in frame 30x30x5mm(Thirty millimeter into thirty millimeter into five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and bellies in any height of propping and centering below supporting floor to ceiling upto floor all level and removal of the same for in situ-reinforced concrete and pain concrete work including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge in:- Foundation, footing basis of columns etc. and mass concrete .

Beams, cantilever, girders and lintels sides and soffits of beams, beam hunching, cantilevers, bressumers and lintels in any depth in all height from floor..

Columns, pillars, Posts and struts, Square, rectangular or polygonal in plan

Stair cases with sloping or stepped soffits excluding landing

Flat surfaces such as soffits of suspended floors, roofs, landings and the like Floors etc upto any thickness.

Vertical surface such as walls(any thickness) and the like including attached pilasters, buttersses plinth and string courses and the like

Edges of slabs and breaks in floors and walls in any width.

Providing and laying M-25 grade design mix of cement concrete 1:1.5:3 (1 cement : 1.5 Sand : 3 graded crushed stone aggregate 20 mm (twenty millimetre) mechanically mixed vibrated and and curing complete excluding cost of form work in as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals . Foundations,footings bases of columns and the like and mass concrete.

Columns, pillars posts and struts etc. up to floor any level.

Suspended Floor roofs, landing and shelves and their support balconies, beams,girders, bressumers and contilever. up to floor any level.

Stair cases (except spiral stair cases) excluding landing but including preparing of the surface and finishing of nosing up to floor any level.

Providing and laying reinforced cement concrete 1:2:4 (one cement : two Sand :four graded stone aggregate 20mm (twenty millimetre) nominal size mechanically mixed and vibrated to give an smooth and even surface including centring and shuttering etc upto all level but excluding cost of reinforcement in String courses, copings, bed plates, anchor blocks, plain windows sills and the like as including carriage of materials with in all leads, lifts and other incidentals per the directions of Engineer-in-Charge.

Providing and laying reinforced cement concrete 1:2:4 (one cement : two Sand :four graded stone aggregate 20mm (twenty millimetre) nominal size mechanically mixed and vibrated to give an smooth and even surface including centring and shuttering etc upto all level but excluding cost of reinforcement in String courses, copings, bed plates, anchor blocks, plain windows sills and the like as including carriage of materials with in all leads, lifts and other incidentals per the directions of Engineer-in-Charge. up to floor any level.

Providing Tor steel reinforcement for R.C.C. work including bending, binding and placing in position complete including cost of binding wire up to any floor level including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Random rubble masonry/polygonal rubble masonry (uncoursed/brought to courses) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (1 cement :6 sand : 12 graded stone aggregate 20mm (twenty millimetre) nominal size at plinth level in Cement Mortar 1:6(1 cement:6 sand) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Stone soling/boulder filling dry hand packed in under floor as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Applying cement slurry on R.C.C. slab or cement concrete work using 2.75 kg. of cement per sq.metre of floor area before laying cement concrete flooring including roughening, cleaning of the concrete surfaces complete. including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Brick work in super-structure above plinth level upto all floor level using common burnt clay building bricks in rat trap bond massonary on (3 edges) in cement mortar 1:3 (One cement : three sand) with second Class bricks including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge .

Half brick masonry in common burnt clay building bricks in cement mortar 1:3 (one Cement :Three Sand) (2nd Class Brick)in super structure above plinth level upto all floor level including carriage of materials with in all leads, lifts and other incidentals as per the direction of Engineer-in-charge.

Providing woodwork in frames of doors,windows,clerestory,windows and other frames wrought,framed and fixed in position 2nd class deodar wood including carriage of materials with in all leads, lifts and other incidentals as per the direction of Engineer-in-charge.

Providing and fixing 35 mm (thirty five millimetre) thick including black enamelled M.S. butt hinges flush door shutters interior grade, commercial type, core of black-board construction with frame of first class hard wood and well matched commercial ply veneering with vertical grains of cross bands and face veneers on both faces of shutters including carriage of materials with in all leads, lifts and other incidentals as per the direction of Engineer-in-charge.

Providing and fixing glazing in door, window, ventilator shutters and partition etc with wooden corner or wooden beaded etc. complete glazing with glass panes of 4mm (four millimetre) thickness (weight not less than 10.00 kg/sqm. (ten kilogram per square metre) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 2nd class deodar wood wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm (zero point five six millimetre) for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screws including carriage of materials with in all leads, lifts and other incidentals as per the direction of Engineer-in-charge.

Providing 40x3 mm (fourty into three millimetre) flat iron hold fast 40cm (fourty centimetre) Long including fixing to frame with 10mm (ten millimetre) diameter bolts & nuts and wooden plugs and embeding in cement concrete block 30x10x15cm (thirty into ten into fifteen centimetre)1:3:6 ( 1 cement : 3 sand: 6 graded stone aggregate 20mm (twenty millimetre) nominal size including carriage of materials with in all leads, lifts and other incidentals as per the direction of Engineer-in-charge.

Providing and fixing anodized aluminium sliding door bolt anodized colour and shade with bolts and nuts screws etc. complete.300x16mm (three hundred x sixteen millimetre) as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing anodized aluminum tower bolts (barrel type ) anodized trans parent or dyed to equired shade and colour with screws etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 250x10mm (Two hundred fifty into ten millimeter)

150x10mm (One hundred fifty into ten millimeter)

Providing and fixing aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. 125 mm (One hundred x twenty five millimeter)

100 mm (One hundred millimeter)

75 mm (Seventy five millimeter)

Providing and fixing 100mm (One hundred millimeter) bright finished brass floor door stopper with rubber cushion screws etc. to suit shutter thickness complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing M.S. plain grills of required patterns in wooden frames of windows etc. with M.S. Flats, square or round bars with round headed bolts and nuts or by screws including carriage of materials with in all leads, lifts and other incidentals as per the direction of Engineer-in-charge.

Providing and fixing PGI Sheet Linning inside of shutter of approved size including bright finished including screws etc. complete including carriage of materials with in all leads, lifts and other incidentals as per the direction of Engineer-in-charge.

Providing nd fixing black board pre-laminated phenol bonded ISI marked with suede finished of size (6 feet x 4 feet) one side of the board to be written with chalk and other the marker complete fixing with screw or nails in position including carriage of materials with in all leads, lifts and other incidentals.as per the directions of Engineer-in-Charge

6mm (six millimetre) Cement plaster to ceiling In Cement Mortar 1:3 (1 Cement : 3 Sand) including carriage of materials within all leads, lifts and other incidentals as per the direction of Engineer-in-Charge.

15mm (fifteen milimetre) cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering up to all floor level includingarises, internal rounded angles,chamfers and/or rounded angles not exceeding 80mm(eighty milimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement:six sand) including carriage of materials within all leads, lifts and other incidentals as per the direction of Engineer-in-Charge.

15mm (fifteen milimetre) cement plaster in single coat on the fair side of brick/concrete/stone wall for interior plastering upto floor all level including arises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (Eighty milimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement:6 sand) including carriage of materials within all leads, and lifts other incidentals as per the direction of Engineer-in-Charge.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete including carriage of materials within all leads, lifts and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing M.S.fan clamp type -1 of 16 mm dia M.S. bar bent to shape with hooked ends in R.C.C slab during laying including painting the exposed portion of loop,all as per standard design complete including carriage of materials within all leads, lifts and other incidentals as per direction of Engineer-in-Charge. .

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equvalent on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete including carriage of materials within all leads, lifts and other incidentals as per direction of Engineer-in-Charge.

Wall painting (two coats) with acrylic emulsion paint of approved brand and manufacture for interior grade on undecorated concrete/stone/plastered wall surfaces to give an even shade including t horoughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty a required for metling the surfaceincluding carriage of materials within all leads, lifts and other incidentals as per direction of Engineer-in-Charge .

Finishing wall with water proofing cement paint of Apex/Altek/Asian or its equivalent make of required shade on undecorated wall surfaces(two coats)to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered material including carriage of materials within all leads, lifts and other incidentals as per the direction of Engineer-in-Charge.

Providing and fixing angle iron cupboard frames manufactured from M.S.Angle iron section 25X25X5mm (twenty five into twenty five into five millimetre) thickness including hinges jamb,lock jamb,beed and if required angle thrashold of mild steel angle 25X25 mm (twenty five into twenty five millimetre) welded or rigidly fixed by mechanical means,lugs with split end tails to each jamb including steel butt hinges 2.5 mm (two point five millimetre) thick with provision for locking arrangement and shock absorber as specified and applying a coat of approved steel primer after preteatment of the surface including carriage of materials within all leads, lifts and other incidentals as per the direction of Engineer-in-Charge.

Providing and fixing 19mm (nineteen millimetre) thick water proof commercial board water proof with 6mm (six millimetre) for cup board with butt joints & fixing with nails & screws etc complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 150 mm (one hundred fifty millimetre) bright finished hard drawn hooks and eyes as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease,dirt and other forein matter sand papering and knotting ready mixed paint with wood priming pink as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Painting two coats(excluding priming coat) on new wood and wood based surface with enamel paint to give an even shade including cleaning the surface of dirt,dust and other foreign matter,sand papering & stoping With enamel paint other than white including carriage of materials within all leads, lifts and other incidentals as per direction of Engineer-in-Charge.

25 mm (twenty five millimetre) thick Kota stone slab flooring 20 mm (Twenty millimetre) (average) thick base of cement mortor 1:4 (1 cement :4 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in Charge .

Kota stone slab 25 mm (twenty five millimetre) thick in risers of steps,skirting dado and pillars laid on 12 mm (twelve millimetre) (average) thick cement mortar 1:3 (1 cement :3 sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing complete including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in Charge.

Providing and fixing 10mm (ten millimetre) thick anti skid impect resistent heavy duty vetrified tiles Nitco or equivalant 300x 300mm (three hundred millimetre into three hundred millimetre ) manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm (twelve millimetre) thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in Charge.

Providing and fixing 20mm (twenty millimetre) thick acid proof stain and impect resistent heavy duty vetrified tiles Nitco or equivalant 300x 300mm (three hundred millimetre into three hundred millimetre ) manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm (twelve millimetre) thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in Charge.

Providing and laying granite stone in flooring 20mm (twenty millimetre) (average) thickness base of cement mortar 1:3(1cement: 3 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone including rubbing and polishing complete including carriage of materials with in all leads, lifts and other incidentals as per directionof Engineer-in Charge.

Providing and fixing 19mm (nineteen millimetre) thick water proof commercial board in shelves/box for cup board with butt joints & fixing with nails & screws etc complete) including carriage of materials with in all leads, lifts and other incidentals as per directionof Engineer-in Charge.

Providing and fixing 19mm (nineteen millimetre) thick Commercial Board water proof shutters for up boards including fixing with nickel plated piano hinges with screws etc complete including carriage of materials with in all leads, lifts and other incidentals as per directionof Engineer-in Charge.

Providing and fixing 1.00mm thick coloured or plain lamination sheet (sunmica) on boards/ply wood sheets with approved adhesive and nails etc complete. including carriage of materials with in all leads, lifts and other incidentals as per directionof Engineer-in Charge.

Providing and fixing Glass reinforced concrete (GRC) screen in approved size, pattren, design, thickness and colour of M/S unistone make or equivalent the screen should be made from " 53 grade " white portlant cement manufactured by "JK cement" or equivalent quartz fine silica sand, alkali resistant glass fiber manufacture by saint Gobain or equivalent super plasticizer manufacure by BASF or equivalent polymers manufacure by BASF or Equivalent and UV resistant synthetic inorganic pigments should be used for pigmentation manufactured by BAYFERROX (Germany) or equivalent the material casting should take place in synthetic rubber/FRP mould manufacture by Recki or equivalent. The fixing of screens should be dry fixing i.e. to be done with stainless steel (SS-304) L-shaped clamps dash fastners and pins as per design and instructions of Engineer-in-Charge including carriage of matrials with in all lead an lift and other incidentals

Providing and fixing 0.60mm (Zero point six zero milimetre) thick preprinterd steel sheet in roofing with hot dipped metallic zinc coasted sheet with top coat of regular modified polyester (RNP) organic coating of 20 (Twenty) microns over 5 ( five) micons primer coating to back coast of polyester of 5 microns over 5 microns primer coating including fixing with screws, prepainted iron J or L hooks, bolts and nuts 6mm(six milimetre) dia with prepainted limpet and rubber washer complete with all accessories as required including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in Charge.

Providing and fixing ridges or hips 60 cm (Sixty centimeter) overall with 0.60 mm (Zero point sixty millimeter) thick preprinted steel sheets in roofing with hot dipped metallic zinc coated sheets with top coat or regular modified polyester organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating + back coat of polyester of 5 (Five) microns over 5 (Five) microns primer coating including fixing with preprinted iron J or L hooks, bolts & nuts 6mm(Six millimeter) dia and preprinted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing valley 60 cm (Sixty centimeter) overall 0.60mm (Zero point sixty millimeter) thick prepainted steel sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 microns over 5 microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (six millimetre) dia with prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-charge including carriage of matrials with in all lead an lift and other incidentals

Providing and fixing flushing 38cm (thirty eight centimetre) overall with 0.60mm (Zero point sixty millimeter) thick prepainted sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm (six millimetre) dia meter & prepainted G.I. limpet & bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge including carriage of matrials with in all lead an lift and other incidentals

Providing and fixing M.S. BP Sheet 1.66mm to 2mm (one point six six millimetre to two millimetre) thick in eaves board/facia/soffits/ ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Steel work welded in built up sections,trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of red lead paint In trusses and trussed purlins in buildings as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing under layer for plinth protection of 75mm (seventy five millimetre) thick (unconsolidated) bed dry brick/stone aggregated 40mm (fourty millimetre) nominal size with rammed and consolidated and grouted with fine sand including preparation of ground as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing plinth protection 50mm (fifty millimetre) thick in cement concrete 1:3:6 (1 Cement : 3 Sand : 6 Graded stone aggregated 20mm (twenty millimetre)nominal size including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in Charge.

Constructing course rubble hammer dressed "U" shape open surface drain with side wall 15X22cm (fifteen into twenty two) in cement mortor 1:6 (one cement: six sand) and in side plstring with cement plaster 1:3 (one cement : three sand ) including earth work and laying 10cm (Ten Centimetre) cement concrete 1:5:10 (one cement :five sand:ten graded stone aggregate 40mm (Forty millimetre) nominal size) and 7.5cm (seven point five centimetre) cement concrete 1:2:4(one cement :two sand ;four graded stone aggregate 20mm (Twenty millimetre) nominal size) and finishing with a floating coat of neat cement and curing complete as per standard design as per the entire satisfaction and including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in Charge.

Providing and fixing 62.5mm x 75mm (sixty two point five millimetre into seventy five millimetre) hand rails in 1st class Indian teak wood straight length complete including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in Charge.

Providing and fixing MS Railing for staircase having balluster of 20mm x 20mm (twenty millimetre into twenty millimetre) square Bars with a clear height of 85cm (eighty five centimetre) embeded in cement concrete steops and jointed with electrical/gas welsing at top along with MS flat of 40 x 6 mm (forty into six millimetre) the balluster welded/jointed with two number MS flat of 40 x 5 mm (forty into five millimetre) size complete with a priming coat of red lead paint as per drawing and specification and including carriage of materials within all leads, lift and other incidentals as per the direction of Engineer-in-Charge.

Providing and fixing modular false ceiling 600mm × 600mm size (Six hundred millimetre into Six hundred millimetre) of Multipurpose Everest Fibre Cement pre-painted Designer tile (High Pressure Steam Cured) of 4mm thickness (as per IS:14862) of size 595×595mm (Five hundred Ninty five millimetre into Five hundred Ninty five millimetre) and any one of the design (oceanic, lake & hill, cascade or electra) in true horizontal level, suspended on inter locking Everest metal grid of hot dipped galvanized steel powder coated sections (galvanized @ 120gsm, both side inclusive) consisting of main “T” runner with suitably spaced joints to be required length and 24×38mm (Twenty four millimetre into thirty eight millimetre) made from 0.25mm (Ziro point twenty five millimetre) thick sheet, spaced at 1200mm (twelve hundred) c/c/ and cross “T”of size 24×27mm (twenty four into twenty seven millimetre) made of 2.24mm (two point twenty four millimetre) sheet, 1200mm (twelve hundred) long spaced between main “T” at 600mm (six hundred millimetre) c/c to form a grid of 1200×600mm (twelve hundred into six hundred millimetre) and secondary cross “T” of length 600mm and size 24×27mm (twenty four into twenty seven millimetre) made of 0.25mm (Ziro point twenty five millimetre) thick sheet to be interlocked at middle of the 1200×600 mm (twelve hundred into six hundred millimetre) panel to form grids of 600×600mm (Six hundred millimetre into Six hundred millimetre) and wall angle of size 24×22×0.4mm (twenty four into twenty two into ziro point four millimetre) and laying false ceiling tiles in the grid including, required cutting/ making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable rods of 3mm dia with galvanized Butterfly level clips, spaced at 1200mm (twelve hundred) c/c/ along main T, bottom exposed width of 24mm of all T-sections (of EIL) shall be pre-painted with polyster paint, all complete at all heights including carriage of materials within all leads, lift and other incidentals as per the direction of Engineer-in-Charge.

Providing and fixing 150mm (one hundred fifty millimetre) dia pipes on wall face PVC (D-Plast) rain water pipes of working pressure not less than 4.5 kg/sqm (four point five kilogram per square metre) including filling the joints with approved adhesive complete including carriage of materials within all leads, lifts and other incidentals as per the direction of Engineer-in-Charge.

Providing and fixing PVC Plain bend 150mm (one hundred fifty millimetre) dia on wall faces PVC (D-Plast) accessories for rain water pipes including filling the joints with approved adhesive complete including carriage of materials within all leads, lifts and other incidentals as per the direction of Engineer-in-Charge.

White glazed tiles 6 mm (six millimetre) thick in skirting risers of steps and dado 12 mm(twelve millimetre) thick cement mortar 1:3 (1 cement :3 sand) and jointed with cement slurry including carriage of materials within all leads, lifts and other incidentals as per the direction of Engineer-in-Charge.

Providing and fixing magnetic locking arrangement for the shutters of cupboards in laboratory etc. with necessary screw and fixing in position in all floors including carriage of materials within all leads, lifts and other incidentals as per the direction of Engineer-in-Charge.

Applying priming coat over new steel & other metal surfaces after & including preparing the surface by thoroughly cleaning oil grease dirt and other foreign matter and scoured with wire brushes fine steel wool scrapers and sand paper complete With ready mixed priming paint brushing red lead,Red-oxide/zinc oxide chrome all leads, lifts and other incidentals as per the direction of Engineer-in-Charge.

Providing and fixing panelled ,glazed or panelled and glazed shutters for doors, windows and clerestory windows including black enameled iron butt hinges with necessary screws 35mm. (Thirty five millimeters) thick, 2nd class deodar wood for all floors all leads, lifts and other incidentals as per the direction of Engineer-in-Charge.

Providing and laying cement concrete 1:5:10 (1 cement : 5 Sand :10 graded stone aggregate 40mm (fourty millimetre) nominal size and curing complete excluding the cost of form work in Foundation and plinth including carriage of materials within all leads, lift and other incidentals as per the direction of Engineer-in-Charge.

Providing and laying cement concrete work 1:1.5:3 (1 Cement:one point five Sand: three graded stone) aggregate 20 mm (twenty millimetre) nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in including carriage of materials within all leads, lift and other incidentals as per the direction of Engineer-in-Charge. Suspended Floor roofs, landing and shelves and their support balconies, beams, girders, bressumers and contilever.

Walls (any thickness but not less than 0.10 metre thickness) including attached pilasters buttersses,plinth and string courses etc.

Brick work using common burnt clay building bricks in foundation and plinth in Cement mortar 1:6 (One Cement : Six Sand) second Class Bricks including carriage of materials within all leads, lift and other incidentals as per the direction of Engineer-in-Charge.

Half brick masonry in common burnt clay building bricks in cement mortar 1:3 (one Cement :Three Sand) (2nd Class Brick)in super structure above plinth level upto all floor level including carriage of materials within all leads, lift and other incidentals as per the direction of Engineer-in-Charge.

40 mm (fourty millimetre) Cement concrete flooring 1:2:4 (1 cement : 2 sand:4 graded stone aggregate 20 mm (twenty millimetre) nominal size laid in one layer finished with a floating coat of neat Cement including carriage of materials within all leads, lift and other incidentals as per the direction of Engineer-in-Charge.

15mm (Fifteen milimeter) cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering including arrises, internal rounded angles, chamfers and / or rounded angles not exceeding 80mm (Eighty milimeter) in girth and finished even and smooth in cement mortar 1:6 (one cement: six sand) including carriage of materials within all leads, lift and other incidentals as per the direction of Engineer-in-Charge.

Supplying cast iron cover with frame for manhole for frame of internal dimension 455 x 610 mm (four hundred fifty five into six hundred ten millimetre) rectangular CI cover the weight of cover to be not less than 38 kg (thirty eight kilogram including carriage of materials within all leads, lift and other incidentals as per the direction of Engineer-in-Charge.

Providing and fixing high pressure PVC spigot and socket waste and ventilating pipes confirming to ISI -15328 SN8 of Supreme/Fenolex/Kitech marked 110 mm dia (one hundred ten millimetre) diaincluding fixing with approved adhesive etc . complete including carriage of materials within all leads, lift and other incidentals as per the direction of Engineer-in-Charge.

Back filling behind abutment wing wall and retainling wall complete as per drawing & technical specification clause 1204.3.8 and including carriage of material with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and laying concrete (C.C 1:6:12) (one cement : six sand twelve graded stone aggregated) 40 mm (fourty mm) for plain/reinforced concrete in open foundation complete as per drawing and technical specification Clause 802,803,1202 and 1203 including carriage of magrials with in all leads and lilfts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and laying concrete for plain/reinforced concrete in open foundations complete as per drawing and technical specification Clause 802,803,1202 and 1203 in cement concrete 1:4:8 (one cement: four sand : eight graded stone aggregate 40mm nominal size) as per entire satisfaction and direction of Engineer-in-Charge including carriage of matrials with in all lead an lift and other incidentals

Random Rubble Stone masonry in cement mortar 1:6 (one cement : six sand) for substructure complete as per drawing & technical specification Clauses 702,704,1202 and 1204 including curing complete within all leads, lifts carriage of material and other incidentials.

Construction of dry rubble masonary for retaining walls, breast walls, revetment walls and parapets etc. for sub structure and super structure complete as per drawing and technical specification Clauses 704.6 & 1302.5, with in all leads and lilfts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing weep hole in brick masonry/ stone masonry / plain reinforced concrete abutment, wing wall, return wall with 100mm dia.(one hundred millimetre diametre) PVC pipe extending through the full width of the structures with slope of 1V:20H (one vertical isto twenty horizontal) towards drawing face complete as per drawing and technical specifications clauses 614,709,1204.3.7 with in all leads and lilfts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Excavation in drain and channels etc. in earth work in all kinds of soils such as pick work, jumper work, pick jumper work , pick jumper blasting work , blasting work in soil and hard rock conglomerate rock or saturated soil and its intermediate classification of soil including chiseling/wedging out of rocks (where blasting is prohibited) and pumping or bailing watering/dewatering including dressing of sides and bed and disposing of excavated earth upto any leads and lifts disposted earth to be leveled and neatly dressed as directed by the Engineer-in charge within any leads including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 20 mm (twenty millimetre) nominal bore to wall ceiling and floor galvanized mild steel tube (medium grade) tube fittings and clamps including making good the wall ceiling and floors with in all leads, lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing plythelineo-aluminiumo-polythelene(PE-AL-PE) composite pressure pipe U.V.stabilized with carbon black confirming to IS-15450-2004 water supply including clamp at one meter spacing,cutting,fixing and making good the wall etc.but excluding the cost of fittings(internal work) pipes exposed on wall.internal worko-exposed on wall. (KITEC make) with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge. 1216 (One thousand two hundred sixteen) 16mm (sixteen millimetre)O.D.Pipe.

1620 (one thousand six hundred twenty) 20 mm (twenty millimetre) OD pipe

Providing and fixing composite end seal compression fittings as per IS-15450-2004 for cold water supply e.g. tees, elbows, reducers, connectors,couplers and clamps with jointing testing and fittings complete including cutting and making good the walls etc. (KITEC make) with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge. Equal tees i)1216 (one thousand two hundred sixteen)

Reducing tees 1620 (one thousand six hundred twenty) x all branches

Female elbows i)1216x15mm (one thousand two hundred sixteen into fifteen millimetre) thread.

Female elbows i)1620x15mm (one thousand six hundred twenty x fifteen millimetre) thread.

Female branch TEE i)1216x1216x15mm (one thousand two hundred sixteen into one thousand two hundred sixteen into fifteen millimetre) thread.

Female thread connector i) 1216x15mm (one thousand two hundred sixteen into fifteen millimetre) thread.

couplers i) 1216 (one thousand two hundred sixteen).

couplers i) 1620 (one thousand six hundred twenty).

Providing and fixing PVC water storage tank of ISI:12701 marked,G.I.inlet and outlet connection,15mm (fifteen millimetre) nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level:-1000 (one thousand)litres capacity. with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc complete. with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge. 75 mm (seventy five) nominal size.

110mm (one hundred ten millimetre) nominal size.

150mm (one hundred fifty) nominal size.

Providing and fixing PVC double equal branch with oval access door, ISI marked insertion rubber washer 3 mm (three millimetre) thick bolts and nuts complete including fixing with approved adhesives etc. with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge. 75 mm (seventy five millimetre) dia

110 mm (one hundred ten millimetre) dia

Providing and fixing PVC door bend with ovel access door ISI marked insertion rubber washer 3 mm thick bolts and nuts complete icluding fixing with approved adhesives etc. all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge. 110mm (one hundred ten millimetre) nominal size.

75mm nominal (seventy five millimetre) size.

Providing and fixing PVC single equal branch plain, ISI marked including fixing with approved adhesives etc. with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge. 75 mm (seventy five millimetre) dia

110 mm (one hundred ten millimetre) dia

Providing and fixing PVC collar, ISI marked including fixing with approved adhesives etc. with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge. 75 mm nominal (seventy five millimetre) size.

110mm nominal (one hundred ten millimetre) size.

Providing and fixing PVC plain bend, ISI marked including fixing with approved adhesives etc. with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge. 75 mm nominal (seventy five millimetre) size.

110mm nominal (one hundred ten millimetre) size.

Providing and fixing PVC clamps, ISI marked of approved design with steel screws and rawal plugs etc. Complete. with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge. 75 mm nominal (seventy five millimetre) size.

110mm nominal (one hundred ten millimetre) size.

Providing and fixing PVC floor trap ISI marked of self cleansing design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge. 110 mm x 75 mm (one hundred ten millimetre into seventy five millimetre ) size.

110 mm x 90 mm (one hundred ten millimetre into ninty millimetre ) size.

Providing and fixing vitreous China wash down, water closet squatting pan (Indian type W.C pan) size 580mm (five hundred eighty millimetre) (Earth work, bed concrete, foot rest and trap to be measured and paid for separately). Orissa pattern (Cera) with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing vitreous china water closet(European type w.c.pan) with integral 'p' or 's' trap including jointing the trap with soil pipe in cement mortar 1:1 (1cement:1sand)(seat and cover to be measured and paid for seprately):-(Cera) Anglo indian universal closet with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing 100 mm (hundred millimetre) size 'P' or 'S' trap for water closet (squatting pan)including jointing the trap with the pan and soil pipe in cement mortar 1:1(1 cement : 1 sand) with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing PTMT coloured/white high density polyethylene/poly propylene 10 (ten) litres capacity ( full flush) European standard control low level flushing cistern with fittings with a pair of brackets with fittings such as lead valve, syphon, 15mm (fifteen millimetre) nominal size PVC ball valve with polythene float,with push button, couplings for connections with inlet,outlet and overflow pipe, 40mm (forty millimetre) dia C.P.flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (over flow pipe to be measured and paid for seprately) with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing G.I. Inlet connection for flush pipe with W.C. Pan with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing vitreous china wash basin No. 10001 of Hindware or its equivalent with single hole for pillar tap with C.I or M.S brackets painted white including cutting holes and making good the same but excluding fitting:- extra for pair of holes for pillar tap instead of single hole, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge. (a) Flat back (i) 550mm × 400 mm (five hundred & fifty millimeter into four hundred millimeter)

Providing and fixing vitreous China padedstal for wash basin complete recessed at the back for the reception of pipes and fittings including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing laboratory sink with CI or MS brackets painted white including cutting holes in walls and making the good the same but excluding fittings. Vitreous China of size 600mm × 450mm × 150mm, (Six hundred into four hundred fifty into one hundred fifty) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing C.P. Brass waste for wash basin or sink:- (a) 32mm dia (Thirty Two millimeter diameter) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing M.I. union for wash basin or sink 32mm dia (Thirty Two millimeter diameter) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 600mmX450mm (Six Hundred into Four Hundred Fifty millimeter) bevelled edge mirror of superior glass mounted on 6mm (Six millimeter) thick A.C. sheet or plywood sheet and fixed to wooden plugs with C.P. brass screws and washers complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing chromium plated brass soap dish with C.P. brass brackets fixed to wooden cleats with C.P. brass screws complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing vitreous china bowl pattern urinal i/c connection the with waste pipe by means of white lead mixed with chopped hemp (waste pipe to be measured and paid for separately) i/c carriage of materials in all leads and lifts and as per the direction of Engineer-in-Charge. Flat back type of size 430x260x350mm (four hundred thirty into two hundred sixty into three hundred fifty (Jaquar or ESS-ESS)

Providing and fixing division plate for urinals 600mm x300mm (six hundred into three hundred millimetre) virterous china including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge. (Jaquar or ESS-ESS)

Providing and fixing plastic seat(solid/hollow type) and cover for wash down water closet with c.p. brass hinges and rubber buffers:-Solid type (a) white plastic seat and cover. including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge.

C.P brass bib tap with capstan head :- 15mm (fifty millimetre) dia (Jaquar or ESS-ESS) including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge.

C.P brass pillar tap with capstan head :- 15mm (fifty millimetre) dia (Jaquar or ESS-ESS) including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing C.P.Brass angle valve 15mm (fifty millimetre) without nuts and pipe. including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing P.V.C connection pipe with brass unions . 300/450mm (Three hundred / four hundred fifty) length 15mm (fifty millimetre) nominal bore including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing Brass full way valve including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge. 15 mm (fifty millimetre) .

20 mm (twenty millimetre) .

Providing and fixing PTMT jet spray of approved quality and colour with 1 (One meter) meter tube including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing 100mm (One hundred millimeter) dia chromium plated grating of superior quality for floor, gully, or Nahni trap including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge.

Constructing manhole with R.C.C top slab in 1:2:4 (1 cement :2 sand :4 graded stone aggregate 20mm nominal size) foundation concrete 1:4:8 (I cement :4 sand : 8 Graded stone aggregate 40mm nominal size ) inside plastering 15 mm thick with cement mortar 1:3(1 cement : 3 sand ) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4(1 cement :2 sand :4 graded stone aggregate 20mm nominal size)finished smooth complete including curing and testing In side size 800mmX 800X500mm (Eight Hundred into Eight hundred Five hundred millimeter) deep including C.I cover with frame. (Light duty single seal: pattern 1) 455mmX 610mm (Four Hundred Fifty Five x Six Hundred Ten millimeter) internal dimensions total weight of cover and frame to be not less than 38Kg. (thirty eight Kilogram) (Weight of cover 23Kg. (Twenty Three kilogram) and weight of frame 15Kg. (Fifteen Kilogram.) (a) With 200mm (Two Hundred millimeter. thick walls of brick masonry using common burnt clay building bricks in cement mortar 1:3(One cement: Three sand). including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge.

providing and fixing automatic flushing cistern with a pair of C.I. or M.S. brackets complete with fitting including C.I syphonic appparatus ,mosquito proof lid, C.P. brass unions and coupling for connection with inlet,outlet and overflow pipe Vitreous china 5 litres capacity including carriage of materials with in all leads and lifts and other incidentals as per the direction of Engineer-in-Charge.

Suket Construction Co. Pvt. Ltd.