Special repair of PHC building at kamnala in Tehsil Nurpur Distt Kangra (HP)(

Excavation in earth work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains in all kinds of soil such as pick work, jumper work, pick jumper work blasting work, jumper blasting work, soft and hard blasting and doing work in saturated soil including Chiseling or wedging out rock where blasting work is prohibited or any other mixed variety of soil including shoring, strutting, dewatering and pumping or bailing out water (Surface and sub soil water )up to any depths or any quantum of water including slush which may arise during dewatering, removal of slush and stacking the serviceable and unserviceable material clear from the edges of excavation with in all leads and lifts as directed by the Engineer-in-charge and then returning the stacked soil in 15 cm ( fifteen centimeters ) layers when required into plinths and sides of foundation etcetera consolidating each deposited layer by ramming, watering and then disposing of all surplus excavated earth as directed by Engineer- in- charge with in all leads and lifts ,disposed earth to be levelled and neatly dressed including carriage of materials within all leads, lifts and other incidentals as per approved drawing , design. The rate is inclusive of octroi, royalty, malkhana, toll tax and any other taxes imposed by the government but Excluding GST.

Providing and laying in position cement concrete of 1:4:8 (one cement; four coarse sand : eight graded /crushed stone aggregate 40mm (forty millimeters) (nominal size) excluding the cost of centering and shuttering:-all works up to plinth level including curing complete as per approved drawing, design , specifications and as per directions and entire satisfaction of Engineer in charge including carriage of materials within all leads , lifts and other incidentals. The rate is inclusive of octroi, royalty, malkhana, toll tax and any other taxes imposed by the government but Excluding GST.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns,drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in- Charge.80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.The rate is inclusive of octroi, royalty, malkhana, toll tax and any other taxes imposed by the government but Excluding GST.

Providing form work with steel plates 3.15mm(three point one five millimeters)thick welded with angle iron in frames 30x30x5mm(thirty into thirty into five millimeters),so as to give a fair finish including centering ,shuttering, strutting and propping etcetera with wooden battens and ballies, height of propping and centering in all heights below supporting floor to ceiling up to any height and removal of the same to in situ reinforced concrete and plain concrete work in Columns, pillars , piers, abutments, post and struts up to all floor level including carriage of materials within all leads , lifts and other incidental and as per approved drawings, design or as per directions of the Engineer- in- charge. The rate is inclusive of octroi, royalty, malkhana, toll tax and any other taxes imposed by the government but Excluding GST.

Providing form work with steel plates 3.15mm(three point one five millimeters)thick welded with angle iron in frames 30x30x5mm(thirty into thirty into five millimeters),so as to give a fair finish including centering ,shuttering, strutting and propping etcetera with wooden battens and ballies, height of propping and centering in all heights below supporting floor to ceiling up to any height and removal of the same for in situ reinforced concrete and plain concrete work in Beams, cantilevers, girders, and lintels, sides and soffits of beams, beam hunchings , cantilevers, girders , bressumers and lintels up to any heights / depths up to all floor level including carriage of materials within all leads , lifts and other incidental as per drawings, design , technical specifications or as per the directions of Engineer- in- charge.The rate is inclusive of octroi, royalty, malkhana, toll tax and any other taxes imposed by the government but Excluding GST.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand) : 4 graded stone aggregate 20 mm nominal size) including carriage of materials within all leads , lifts and other incidental as per drawings, design , technical specifications or as per the directions of Engineer- in- charge.The rate is inclusive of octroi, royalty, malkhana, toll tax and any other taxes imposed by the government but Excluding GST.

Providing and fixing up to floor five level precast cement concrete hollow block, including hoisting and setting in position with cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centering, shuttering complete.1:1½:3 (1 Cement: 1½ coarse sand): 3 graded stone aggregate 20 mm nominal size) . within all leads , lifts and other incidental and as per approved drawings, design or as per directions of the Engineer- in- charge. The rate is inclusive of octroi, royalty, malkhana, toll tax and any other taxes imposed by the government but Excluding GST.

Providing and applying 15mm (Fifteen millimeters) thick cement plaster with cement mortar 1:6 (one cement isto six sand) in single coat on rough side of brick/concrete/stone walls for interior plastering including making groove or drip course, arises, internal rounded angles, chamfers and or rounded angles in all girth and finished even and smooth and curing complete up to all floor level as per approved drawing, specifications as per the direction of Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate is inclusive of octroi, royalty, malkhana, toll tax and any other taxes imposed by the government but Excluding GST.

Finishing walls with apex weather proof exterior emulsion of Asian / Dulux / Berger / Nerolac Suraksha paints of approved shade having VOC less than 50 gm/liter (Fifty gram per litre) and UV resistance as per IS 15489:2004 Alkali and fungal resistant, dirt resistant exterior paint of required shade with silicon additives, New work two or more coats applied @ 1.43 liter/ 10 sqm (One point four three litre per ten square meter) over and including priming coat of exterior primer applied @ 0.90 liter/10 sqm (Zero point nine zero litre per ten square meter) up to all floor level complete as per architectural drawing approved, specifications, design and as directed by the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate is inclusive of octroi, royalty, malkhana, toll tax and any other taxes imposed by the government but Excluding GST.

Steel reinforcement Thermo-Mechanically Treated bars of grade Fe-500 (D) (five hundred D ) of TATA Tiscon/ Sale for reinforced cement concrete work including straightening, cutting, bending, placing in position and binding all complete upto plinth level to all floors level as per approved drawing, design, specifications or as per directions and entire satisfaction of the Engineer -in- charge including carriage of materials within all leads , lifts and other incidentals. The rate is inclusive of octroi, royalty, malkhana, toll tax and any other taxes imposed by the government but Excluding GST.

Brick work with common burnt clay F.P.S. (non modular ) bricks of class designation 7.5 (seven decimal five) in super-structure above plinth level up to all floor level in cement mortar 1:6 (one cement is to six coarse sand) and curing complete as per approved drawing, design or specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is inclusive of octroi, royalty, malkhana, toll tax and any other taxes imposed by the government but Excluding GST.

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer’s specification.Two or more coats on new work entire satisfaction of the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.The rate is inclusive of octroi, royalty, malkhana, toll tax and any other taxes imposed by the government but Excluding GST.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-incharge. Glazing, paneling and dash fasteners to be paid for separately) For fixed portion Powder coated aluminium (minimumthickness of powder coating 50 micron)frameThe rate is inclusive of octroi, royalty, malkhana, toll tax and any other taxes imposed by the government but Excluding GST.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-incharge. Glazing, paneling and dash fasteners to be paid for separately) For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)The rate is inclusive of octroi, royalty, malkhana, toll tax and any other taxes imposed by the government but Excluding GST.

Providing and fixing glazing in aluminium door, window,ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architecturaldrawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basicitem):With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm)with in all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royalty, malkhana, toll tax and any other taxes imposed by the government but Excluding GST.

Providing and fixing 100 mm (one hundred millimeters) aluminum handles ISI: marked anodised (anodic coating note less than grade AC-10 (ten) as per ISI :1868) transparent or dyed to required colour or shade with necessary screws etcetera complete as per approved drawing, design, specification or as directed by the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate is inclusive of octroi, royalty, malkhana, toll tax and any other taxes imposed by the government but Excluding GST.

Providing and fixing 250mm (Two hundred fifty millimeters) size M.S. Hooks and Eyes with necessary screws etcetera complete including as per specifications, approved drawing, design and as directed by the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate is inclusive of octroi, royalty, malkhana, toll tax and any other taxes imposed by the government but Excluding GST.

Providing and fixing 250mm (Two hundred fifty millimeters) size M.S. Hooks and Eyes with necessary screws etcetera complete including as per specifications, approved drawing, design and as directed by the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate is inclusive of octroi, royalty, malkhana, toll tax and any other taxes imposed by the government but Excluding GST.

Structural steel work of Tata / Sail / Reliance/Jindal riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete as per approved specifications drawing, design and as directed by the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate is inclusive of octroi, royalty, malkhana, toll tax and any other taxes imposed by the government but Excluding GST.

Painting (two or more coats) with premium enamel paint of Asian Dulux /Berger paints/Nerolac paints (above Dado/skirting) of approved brand and manufacture for interior grade on undecorated concrete/stone/plastered wall surfaces to give an even shade including thoroughly brushing the surface free from mortar droppings, other foreign matter and sand papered smooth including applying of putty as required for making the surface smooth complete up to all floor level as per architectural drawings, approved specifications , design and as directed by the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate is inclusive of octroi, royalty, malkhana, toll tax and any other taxes imposed by the government but Excluding GST.

Providing and fixing 0.60 mm (Zero point six zero millimeters) thick prepainted steel sheet (ISI marked-Z-120) of Tata Dura shine / Sail / Reliance / Jindal steel in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RMP) organic coating of 20 (Twenty) microns over 5 (five) microns primer coating to back coat of polyester of 5 (five) microns over 5 (five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (Six millimeters) diameter with prepainted limpet and rubber washers complete with all accessories as required as per approved specification , design and as directed by the Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate is inclusive of octroi, royalty, malkhana, toll tax and any other taxes imposed by the government but Excluding GST.

Providing and fixing factory made prepainted steel sheet ridges or hips having proper gola/ shape of corrugation of steel sheet 60 cm (Sixty centimeters) overall with 0.60 mm (Zero point six zero millimeters) thick prepainted steel sheet of Tata / Sail / Reliance / Jindal in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster, organic coating of 20 (Twenty) microns over 5 (five) microns primer coating + back coat of polyester of 5 (five) microns over 5 (five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6 mm (Six millimeters) diameter prepainted G.I. limpet and bitumen washers complete with all accessories as required as per approved specifications , design and as directed by the Engineer-in-charges including carriage of materials within all leads, lifts and other incidentals .The rate is inclusive of octroi, royalty, malkhana, toll tax and any other taxes imposed by the government but Excluding GST.

Providing and fixing plain asbestos cement sheet ceiling of approved quality with butt jointing and wood screws (frame work and cover fillets to be measured and paid for separately)4 mm thickas required as per approved specifications , design and as directed by the Engineer-in-charges including carriage of materials within all leads, lifts and other incidentals .The rate is inclusive of octroi, royalty, malkhana, toll tax and any other taxes imposed by the government but Excluding GST.

Providing and fixing 455x610mm (four hundred fifty five into six hundred ten millimeters) light duty rectangular C.I. manhole cover with frame, weight of cover with frame to be not less than 58KG (fifty eight kilograms) (single seal pattern-I) complete including entire carriage of materials within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royalty, malkhana, toll tax and any other taxes imposed by the government but Excluding GST.

Providing and laying Double Charge Vitrified Tiles of Johnson/ Nitco/Kajaria / AGL / Simpolo / Somany /Orient Bell of size of 600 mm x 600 mm (six hundred millimeter into six hundred millimeter) (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades in Floors having joints of 3 mm width laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), Grouting the joints of flooring tiles using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge complete. The rate is inclusive of octroi, royalty, malkhana, toll tax and any other taxes imposed by the government but Excluding GST.

Providing and Fixing 2mm (two millimeters) thick PVC (Polyvinyl chloride) plain paneling on wall with necessary screws complete or with approved adhesive complete as per netire satisfaction and directions of Engineer in charge complete including carriage of matreials with in all leads and lifts and other incidental.The rate is inclusive of octroi, royalty, malkhana, toll tax and any other taxes imposed by the government but Excluding GST.

Providing and laying in position machine batched and machine mixed cement concrete work of grade1:2:4 design mix to obtain the minimum compressive strength of 20N/mm2 (Twenty newton per square millimeter) , using cement contents not less than @ 330 kg/cum (at the rate Three hundred thirty kilogram per cubic metre) or as per approved design mix. All works level to give a smooth surfaces mechanically mixed and vibrated including curing complete and pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability etcetera as per specifications, approved drawing, design and as directed by the Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals .The rate is inclusive of octroi, royalty, malkhana, toll tax and any other taxes imposed by the government but Excluding GST.

Providing and Fixing 2mm (two millimeters) thick PVC (Polyvinyl chloride) plain paneling on ceiling with necessary screws complete or with approved adhesive complete as per netire satisfaction and directions of Engineer in charge complete including carriage of matreials with in all leads and lifts and other incidental.The rate is inclusive of octroi, royalty, malkhana, toll tax and any other taxes imposed by the government but Excluding GST.