PROVN OF 01X COMPOSITE LABORATORY UNDER PM SHRI SCHEME AT KV NO. 1 KANCHRAPARA UNDER GE BARRACKPORE

Amount

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specially provided for complete all as specified and directed.

Taking down all existing roof treatment including demolition of cement concrete padding/levelling coarse (any thickness as available at site) including wire brushing and cleaning loose dust etc from surfaces of RCC roof including flashing and junction of parapet complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillar etc but excluding ashlars facing dressed stonework & precast concrete articles complete all as specified and directed.

Separating, scraping and cleaning of reinforcement obtained from Ser item No. 1.00 here-in-before complete all as specified and directed.

M&L for 25mm thick PCC (1:2:4) type B0 (using 12.5mm stone aggregate) as levelling course, padding on chajjas etc including angular moulding at junction upto 10cm height with WPC as per manufacturer's instruction, applied over prepared surface and finishing cement concrete surface even and smooth using extra cement complete all as specified and directed. (Note : (i) WPC shall be measured and paid extra as supply only. (ii) PCC shall be laid to achieve true slope towards the drain/weep holes)

M&L for single component cold applied elastromeric waterproofing coating (Dr Fixit Roof Seal Ultra or equivalent) on in-accessible/ accessible roof or wall & floor based on synthetic resin emulsion, tough yet flexible coating that can be efficiently applied by roller or squeeze having following important features : (i) High film build up provides excellent water resistance. (ii) Excellent flexibility and elongation properties can easily accomodate all normal building movements. (iii) Can be applied to complex shapes to form a seamless and highly durable water proofing coating. (iv) Adheres firmly to most of building surfaces including both horizontal and vertical surfaces of parapets etc. (v) Suitable consistency for easy application by brush, roller or squeze. Single component cold applied elastomeric waterproofing coating (Dr Fixit Roof Seal Ultra or equivalent) shall be applied by sprinkling some water over the roof just before application of first coat @ 0.75 Ltr/Sqm uniformly over the entire flat surface including vertical parapets including reinforcing fibre (45 GSM glass fibre mesh) and allow for drying for 12 Hrs and 2nd coat @ 0.75 Ltr/Sqm shall be applied (perpendicular direction of first coat as per manufacturer's instruction) on dried first coat complete all as specified and directed. (Note : (i) Entire application shall be carried out by TRAINED CERTIFIED MANUFACTURER'S APPLICATOR only. (ii) Waterproofing treatment shall cover minimum 10 Yrs warranty by the applicator and Contractor. (iii) Quoted rate shall include WATER PROFFING TEST : After full drying of second coat for atleast 72 Hrs, a water ponding test can be performed by filling water on the terrace by carefully blocking all the down take drain outlet without damaging the coating. The test shall be carried out for 48 Hrs by filling water upto 50mm level. Observe for leakages, if any, and then remove the water and allow the coating to dry completely for handing over site. (iv) Application shall be restricted in open sunlight having temparature above 35°C.

Providing form work to sides of rectangular pillars, posts, struts, piers, columns and stanchoins of rough finished surface of concrete complete all as specified and directed.

Providing form work to sides and soffits of roof beams, lintels, cantilevers, shelves including supports, overhangs etc for flat, rough finish surface of concrete complete all as specified and directed.

Providing form work to soffits of suspended flat slabs of roof slabs, floor slabs, landings and similar work, not exceeding 200mm thick (horizontal or sloping) for flat, rough finish surface of concrete complete all as specified and directed.

Roughening surfaces of old concrete floor/roof by picking, sweeping clean and washing down with water to remove dust and brushing with neat cement slurry with 3.0 Kg of cement per Sqm complete all as specified and directed.

M&L for RCC M-25 Design Mix (using 20mm graded crushed stone aggregate) as in column, pillar, piers, post and struts etc complete all as specified and directed.

M&L for RCC M-25 Design Mix (using 20mm graded crushed stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5 m span complete all as specified and directed.

M&L for RCC M-25 Design Mix (using 20mm graded crushed stone aggregate) as in slabs supported on beams and columns in roofs, deck slabs, shelves and like complete all as specified and directed.

M&L for brick work with sub class 'B' bricks locally available best quality straight or curved on plan exceeding 6m mean radius, built in cement mortar (1:6) complete all as specified and directed.

M&L for brickwork with subclass 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar (1:4) complete all as specified and directed.

S&F 25mm thick solid PVC composite sheet, prelaminated on front side and plain matching dark shade laminated background as in Cubboard flush shutters, fixed with and incl SS flush screws incl necessary cutting for reqd shape, rebate, hinges, hooks, etc and fixing only of self closing hinges, wall hanging hooks, magnetic locks, handles, etc complete all as specified and as directed. (Note :- (i) Necessary Hinges, hooks, handles and locks shall be measured and paid separately as' Supply Only' (ii) Labour charges for 'supply only' items are deemed to be included with quoted rates)

Supply only heavy duty Slim Nickel plated Stainless steel magnetic catch (L shape) with strong earth magnet, size 11mm x 35mm x 4mm complete all as specified and directed.

Supply only heavy duty stainless steel slip on hinges, self closing type with opening full overlay or 105°, suitable for 25mm thick shutter of maximum size 850mm x 550mm complete all as specified and directed.

Supply only ergonomically designed powder coated Aluminium anodised handle, finger pull type, suitable for 25mm thick shutter, size 10-15mm x 200mm complete including finish complete all as specified and directed. (Notes for item No. 17.00 to 19.00 :- Material for Item No. 17.00 to 19.00 to be incorporated in Item No. 16.00 here-in-before)

S&F of 35 mm thick flush door shutters (factory made) solid core construction with block board core and plywood face panels commercial type on both sides including vision panels, square or rectangular, 02 glass sheets shall be fixed back to back with 20-25mm wooden bead separation including lipping complete all as specified and directed. (Note : Glass sheet shall be measured and paid separately).

S&F of 4mm thick sheet glass, ordinary quality in square not exceeding 0.5 Sqm in each pane complete all as specified and directed.

S&F for 100mm long butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed.

S&F of floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed to floor of overall length of coverplate 140mm complete all as specified and directed.

S&F powder coated anodised aluminium alloy sections 5 tier track sliding windows (03 Glass + 02 mesh) series B weight of section frame (bottom 1.792Kg/m and other 1.523 Kg/m) and shutter (section weight 0.641 kg/m and 0.549 Kg/m) duly fitted with neoprene beading, glazing clips, tinted glass panes 5.0mm nominal thickness, aluminium wire cloth 0.45 mm dia and average width of aperture 1.4mm, aluminium alloy handles etc complete all as specified and directed. (Note : Rate shall include all glazing/aluminium wire cloth, rubber packing, joining, cleats, glazing clips, aluminium snap beading, locking arrangements, handle etc.)

M&L for TMT bars 10 mm dia and over cut to length bent to shape as required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

S&F of rolled mild steel as in Joist, channel, angle, or tee sections, fixed independently, without connecting plates (cut to ordinary lengths) conforming to Fe-410-W (Gde E-250) quality 'A' complete all as specified and directed.

S&F of mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or forged into spikes; framed guard bars; barred iron doors; ladders, railings, framed brackets, walk ways, frame work of water tank and similar work conforming to Fe-290-0 Gde-E-165 complete all as specified and directed.

M&L for 40 mm thick cement concrete (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in flooring for laying floor finishes complete all as specified and directed.

M&L for 25 mm thick cement concrete (1:2:4) type B-0 (using 12.5mm graded crushed stone aggregate) as in levelling course below kota stone flooring complete all as specified and directed.

M&L for non skid (joint free) ceramic coloured tiles (Matt finish) of 8mm to 10mm mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc set and jointed in neat cement slurry and pointed with white cement mixed with pigment to match with shed of tiles over and including 15mm thick screed bed or bedding layer of cement mortar (1:4) for laying floor finishes complete all as specified and directed.

All as per Item No.32.00 here-in-before but in skirting/dado over and including a backing coat of 10mm thick plaster in cement mortar (1:4) complete all as specified and directed.

M&L for glazed ceramic coloured tiles (colour & shade as approved by GE) in vertical surface of size 450mmX 300mmX7 to 8mm thick set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10 mm thick rendering of cement mortar (1:4) complete all as specified and directed.

M&L for 18-20mm thick Mirror polished, high gloss finish Granite (absolute Jet Black) work in jambs and soffits of chowkat (including necessary pasting), pillars, window-cills, working platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl necessary cutting for sunk basin/sink, making holes for fixing hinges, door bolts, etc 15mm thick screed bed or bedding layer of cement mortar (1:4) for laying floor finishescomplete all as specified and directed.

M&L for 20mm to 25mm thick machine cut mirror polished kota stone slab flooring over cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing over and including a backing coat of 15 mm thick bedding in cement mortar (1:6) complete all as specified and directed.

Providing edge moulding to 18-20mm thick granite stone slab including machine polishing to edge to give high gloss finish complete all as specified and directed.

M&L for 20mm to 25mm thick machine cut cudappah stone slab over cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete all as specified and directed.

Providing edge moulding to cuddapah stone slab one edge as in steps, cooking platform etc complete all as specified and directed.

M&L for rendering 15 mm thick on fair face of brick works or concrete surfaces of walls with cement mortar (1:4) in two coats (10mm thick backing coat + 5mm thick plaster) mixed with WPC @200ml per 50 Kg of cement on 5mm thick plaster, finished the surfaces even and smooth without using extra cement complete all as specified and directed. (Note : WPC will be measured and paid separately)

Supply only integrated liquid water proofing compound complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:6) on brick work or concrete surfaces of wall, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5mm thick in cement mortar (1:4) on fair surface of wall finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5mm thick in cement mortar (1:3) on ceiling, chajja etc surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for applying 3mm thick wall care putty on wall surfaces complete all as specified and directed.

M&L for applying two coats of plastic emulsion paint over a coat of alkali resistant primer on prepared wall surfaces, surface area not exceeding 10 cm girth or width complete all as specified and directed.

M&L for applying two coats of 100% Premium acrylic emulsion paint(using AIR-LESS PAINT SPRAYER) having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over wall surfaces by using AIR-LESS PAINT PRIMER SPRAYER using smart technique including preparation/levelling of new surface of wall using manual sand papers(where reqd) of approved grade using smart painting technique complete all as specified and as directed.

M&L for applying two coats of synthetic enamel paint (1st grade quality) over a coat of pink primer after preparation of new or previously untreated wooden surfaces of any description over 10cm width or girth complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer after preparation of new or previously untreated steel surfaces of any description over 10cm width or girth complete all as specified and directed.

Supplying and laying of 20mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings, concealed joint with CPVC adhsive taflon tape complete on walls/ ceiling or laying in floors including all connecting brass CPVC fittings and cutting grooves, filled with cement mortar 1:4 complete all as specified and directed.

Supplying and laying of 25mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings, concealed joint with CPVC adhsive taflon tape complete on walls/ ceiling or laying in floors including all connecting brass CPVC fittings and cutting grooves, filled with cement mortar 1:4 complete all as specified and directed.

Supplying and laying of 50mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings, concealed joint with CPVC adhsive taflon tape complete on walls/ ceiling or laying in floors including all connecting brass CPVC fittings and cutting grooves, filled with cement mortar 1:4 complete all as specified and directed.

S&Fof Brass CP Sink Mixer with movable neck, fixed to wall, for mixing hot & Cold water screwed down for iron pipe and fixed and joint with adhesive, taflon tape, etc complete complete all as specified and directed.

S&F of sinks made of stainless steel 1.5mm thick laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 585mm x 485mm bowl size 535mm x 432mm x 200mm complete all as specified and directed.

S&F 40mm Brass chromium palted bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and directed.

S&F of 500 Ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) multi layer, (three layer) ISI Marked hoisted and fixed in position with cover of tank with its locking arrangement, making hole for inlet, outlet and overflow connection with and including 20mm dia ball valve high pressure of PTMT (minimum weight 210 gms) complete all as specified in SSR Part-I and directed.

SCH 'A' PART-II : M&L for point wiring complete with 1.5 sqmm PVC insulated, FR-LSH type, ISI marked, conforming to IS-694/1990 unsheathed, multistranded, single core, copper conductor cable 1100 volts grade colour code cables drawn through and including PVC Conduit 20 mm dia medium grade (MMS) and including cutting, chasing work at any height and all accessories concealed in walls / roofs / floors / ceiling etc. flush mounting MS box with top, bottom, side/back wall knockout for conduit entry from any direction made out of 1.60mm thick and 50mm depth suitable for fixing of modular top cover , blanking plate as per numbers of switch modules, modular switches, sockets, fan regulators, red colour indicator, blank plates etc as approved coloures modular accessories of suitable modules and including 1.5 Sqmm PVC insulated multistranded FR-LSH type unsheathed single core cable with copper conductor cable as earth continuity conductor and connecting to common earth dolly and including making good the disturbed surfaces to match with existing surfaces by applying white/colour wash/distemper as applicable after applying of putty for smooth finish surface complete all as specified and directed for the following:- (Note:- (i) All necessary accessories such as MS box, top cover plate, blank plate, screws, washers etc are to be used of same make/brand only in relevant items. (ii) Cutting & chasing of wall for point wiring at any height shall be done and cost of the same deemed to be including with quoted rate.)

One light point controlled by one switch .

One 3 pin socket outlet 5 Amps on the same board

One fan/exhaust fan point controlled by one switch and one regulator.

One 3 pin socket outlet 5 Amps on independent board

Ditto- all as per Item No.57.00 here-in-before but point wiring with 2.5sqmm PVC insulated multistranded flexible unsheathed copper conductor FR-LSH and earth conductor of size 2.50 sqmm for one 15 amps socket outlet point controlled by one 16 amps switch on independent board. complete all as specified and directed.

S&F of stepped type (0-4/5 step) electronic fan regulator 240 Volts, 100 Watts to 120 watts single pole including connecting, testing complete all as specified and directed.

S&F of socket out let, flush type, 2 in 1, 3/5 pin, 5/6 Amps, 240 volts, AC complete all as specified and directed.

S&F of switch piano flush button single pole, one way, 5 amp, 240 volts, AC, complete all as specified and directed.

S&F of socket out let, flush type, 2 in 1, 3/5 pin, 5/6 to 15/16Amps, 240 volts, AC complete all as specified and directed.

S&F of switch piano flush button single pole one way 15 amp 240 volts, AC complete all as specified and directed.

S&F of ceiling rose, surface bakelite 65X50mm, three terminal, PVC/polycarbonate body complete all as specified and directed.

S&F of powder coated sheet metal enclosure 240 volts AC, SPN distribution board 8 way for flush mounting with 200 Amps copper busbar, neutral bar, earth bar and MCB incomer of rating upto 200Amps, MCB SPN/DP and MCB SP as outgoing and complete connecting cable links with top and bottom removable gland plate with IP 43 DBs protection and including making good the disturbed surfaces to match with existing surface & colour coat including taking down old unserviceable DBs complete all as specified and directed. (Make: Legrand Cat No. 5076 21 8 way /L&T Cat No.DBSPN008GD/C&S Cat No. CSDBSPNPCGDD08 or equivalent model/Cat No of make as per Appx 'A' as mentioned in PS here-in-after)

S&F of MCB, SP, 6 Amps to 32 Amps , 'C' series, 240 Volt, 10KA, 50 Hz complete all as specified and directed

S&F of RCBO double pole for earth leakage, overload and short-circuit protection 40 Amps, 30mA, 240 Volts, 50 Hz including necessary incoming and outgoing electric connection complete all as specified and directed

M&L for sub main wiring complete with 2 run of 6 sqmm single core copper conductor (ISI marked) cable 1100 volts grade, FR-LSH type, PVC insulated, unsheathed, flexible, multi stranded colour coded cables drawn through and including rigid PVC conduit of required size medium grade (MMS) with all connected accessories such as Bend, Tee, Elbow, Short pieces etc concealed in wall/roofs/floors and including one run of 6 sqmm single core copper conductor cable flexible, PVC insulated, unsheathed, multistranded, 1100 volts grade, FR-LSH type as earth continuity conductor connected to common earth dolly and including chease cutting and filling the same with cement mortar and finished with putty and making good the disturbed surfaces to match with existing surface as required for concealed work complete all as specified and directed . (Note for item No. 103 & 104 : (i)Two runs of cable with one run earth wire and PVC conduit shall be measured as one length. (ii) Extra length of cable required for connection to DBs shall be deemed to be included in the unit rate and shall not be measured separately. (iii) Earth wire shall run inside the conduit. (iv) Suitable color code of wire must be ensured for phase/netural/earth. (iv) All surface cutting/making good for wiring/switch board/junction box/DB etc are included with unit quoted rate.)

S&F of decorative box type 20 -22watt LED fittings with and including LED T-8 tube light 20 watt of fire retardant engineering grade complete with all accessories internally pre-wired, connecting up with and including three core sheathed flexible copper conductor cable of required size and including mounted on PVC/Wooden round/square blocks-02 Nos complete all as specified and directed. (Make : Philips Cat No. TMC501T8 and MAS LED tube PC body/ Crompto Greeves Cat No. IGP 118 T8 and LT8-20865-2/ Surya Cat No. SUB 118 T8 & SLETLDS 20 PC or equivalent model/Cat No of make as per Appx 'A' as mentioned in PS here-in-after)

Supply, fixing and testing Ceiling fan BLDC type with all accessories, 230V, 1200mm sweep, BEE 5 star rated, 03 blade type, double ball bearing copper wound, 50 Hz, AC supply complete all as specified and directed.

S&F for exhaust fans, AC, single phase 230V/240V of size 300mm sweep with louver including making hole for fixing of exhaust fan and making good the disturbed surfaces complete all as specified and directed. (Make: Crompton Greaves Cat No.Trans Air 4 Blade/Havells Cat No. Turbojet SP 1400RPM as approved)

B N ENTERPRISE (BID ID -3172705)

M/s S K SHARMA (BID ID -3172512)

SWAPAN CONSTRUCTION (BID ID -3172358)

DE CONSTRUCTION CO (BID ID -3172599)

M/s Manoj Kumar Gope (BID ID -3172634)

PUNAM ENTERPRISE (BID ID -3172546)

S S ENTERPRISE (BID ID -3172655)