1. Netaji Subhash Chandra Bose Avasiya Vidyalaya (Hostels) - NR (New) (Upgradation till XII) Construction of 50 Beded Hostel at HSS Trespone Under SAMAGRA Shiksha

Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres:

All kinds of soil 80 %

Ordinary rock@10%

Hard rock (Blasting Prohibited)@10%

Earth work in excavation by mechanical means (Hydraulic Excavator) over areas exceeding 30cm and up to 1.50Mtr in depth 1.5 mtr in width as well as 10 sqm on plan)Including disposal of excavated earth upto 1Mtr from cutting edge, disposed earth to be leveled and neatly dressed in:

All kinds of soil @70%

Soft Rock @10%

Hard rock (BP) @20%

Disposal of exacvated earth for an avg lead of 5km by Mt

Dry stone pitching (any thickness) excluding cost of stones. On Horizontal

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level.1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) Crushed:

Random Rubble masonry with hard stone in foundation and plinth including leveling up with cement concrete 1:6:12 (1 Cement : 6 coarse sand : 12 graded stone aggregate 20mm nominal size) upto plinth level and 7.1.1 Cement mortar 1:6 (1 Cement : 6 coarse sand)

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m.

Providing & fixing upto floor five level precast cement concrete solid blocks including hoisting and setting in position with cement motor 1:3(cement: 3 course sand) cost of required centering shuttering and finishing smooth with 6mm thick cement plaster 1:3(1cement:3 fine sand) on exposed surface complete 1:3:6(1cement:3 coarse sand :6 graded stone agg, 20mm nominal size

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors ,roofs having slope up to( 15 degree)landings ,balconies ,shelves ,chajjas,lintals bands ,plain windows sills ,stair cases and spiral stair cases up to floor five level excluding the cost of centering ,shuttering ,finishing and reinforcement with 1:1.5:3(1cement:1.5coarse sand:3graded crushed stone aggregate 20mm nominal size)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry , but excluding the cost of nosing of steps extra complete.50mm thick with 20mm nominal size stone aggregate Crushed:

15mm cement plaster on the side of single or half brick wall fiished with a floating coat of neat cement of mix : 1: 4( 1cement :4 fine sand)

Centring and shuttering including strutting, propping etc. and removal of form work complete.Foundations, footings, bases of columns etc. for mass concrete.

Walls (any thickness) including attached pilasters, buttresses, plinth andstring courses etc.

Lintel, beams, plinth beams,girders,bressumers and cantilever.

Suspended floors, roofs, landings, balconies and access platforms.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).1st Class Kail Wood

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for eparately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately)Second class kail wood 9.5.5.1 35 mm thick shutters

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, indows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : 9.7.2.2 Second class Kail wood

Providing and fixing 4 mm thick float glass panes, including beading of 1st class kail wood with necessary screws.

Providing and applying white cement based putty of average thickness 2 mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complet

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer

Rough cast plaster upto 10m height above ground level with a mixture of sand and gravel or crushed stone from 6mm to 10mm nominal size dashed over and including the fresh plaster in two layers , under layer 12 mm cement plaster in 1:4 ( 1 cement: 4 coarse sand ) and top layer 10 mm cement plaster with cement mortar 1:3 ( 1 cement: 3 fine sand ) mixed with 10% finely grounded hydrated lime by volume of cement.

Finishing walls with textured exterior paint of required shade :New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and includingpriming coat of exterior primer applied @ 2.20kg/10 sqm

6mm cement plaster to ceiling of mix 1:3 [1 cement, 3 fine sand]

Providing and fxing of Traditionally curved wood work shingstyak over door and wondows including all acessoires complete .

Providing and fixing ISI marked oxidized M.S. tower bolt black finish, (Barrel type) with necessary screws etc complete

Providing and fixing ISI marked oxidized M.S. sliding door bolts with nuts and screws etc. complete : 300x16 mm

Providing and fixing ISI marked oxidized M.S. handles conforming to IS : 4992 with necessary screws etc. complete :125 mm

25 mm wooden planking, tongued and grooved in flooring, including fixing with iron screws complete with : Second class kail wood

Providing and laying roof insulation with 40 mm thick impervious sprayed, closed cell free Rigid Polyurethane foam over deck insulation conforming to IS - 12432 Pt. III (density of foam being 40-45 kg/cum), over a coat of polyurethane primer applied @ 6-8 sqm per liter, laying 400 G polythene sheet over PUF spray and providing a wearing course of 40 mm thick cement screed 1: 2 : 4 (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size) in chequered rough finish, in panels of 2.5 m x 2.5 m and embedding with 24 G wire netting and sealing the joi with polymerized mastic, all complete as per direction of Engineer-inCharge

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceilingwith dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with ntermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with taperedflanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connectingclips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimetre channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimetre of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimetre channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges ofthe board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers,cutouts made with frame of perimetre channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excludingthe cost of painting with :

Fully Perforated Gypsum Plaster Board of size 1200 x 2400x12.5 mm having approx. 15 % perforated areawith perforation size and pattern as approved by the Engineer-in-charge and as per anufacturer'sspecification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.61

Providing and fixing precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, omplete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing ridges or hips of width 60cm overall width plain G. S. sheet fixed with poymer coated J. or L hooks, bolts and nuts 8mm G. I. limpet and bitumen washers complete. 0.80 mm thick with zinc coating not less than 275gm /m2 specifications as per engineer in charge

Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

French sprit polishing with two or more coat on new work including a coat of wood filler.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 13755 of NITC.O, ORIENT, SOMANY, KAJARIA or equivalent make in colour such as White, Ivory, Grey, Fume Red, Brown laid on 20 mm thick bed of Cement Mortar 1: 4 ( 1 cement : 4 coa.rse sand) including pointing the joints with white cement and matching pigment etc., complete. In all colours, shades, except White, Ivory, Fume Red Brown

Providing and laying gang saw cut 30 mm thick, mirror polished pre moulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring in road side plazas and similar locations, laid over 20mm thick base of cement mortar 1:4 (1 cement : 5 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction of Engineer-in-Charge. With granite stone of colour black, cherry/ruby red of area less than 0.50 sqm.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). Size of Tile 600x600 mm

Chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) Light shade pigment using white cemen

Providing and Fixing12mm thick ply with 4"width T & G approved brand including polishing surface and beading with design as per engineer incharge all complete job

Providing and fixing thermal insulation with Resin Bonded Fibre glass wool conforming to IS: 8183 havingdensity 24 kg/m3, 50 mm thick, wrapped in 200G Virgin Polythene Bags fixed to wall with screw, rawel plug& washers and held in position by criss crossing GI wire etc. complete as per directions of Engineer-in

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc. including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete ,including fixing the railingn with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement including king posts of required pattern as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered including fixing accessories such as nuts, bolts, fasteners etc.)."

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever requiredOrissa pattern W.C. pan of size 580x440 mm with integral type foot rest

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. / M.S. brackets 15 mm C.P brass pillar taps, Kingstone/ Gem/ Techno/ Parko/Jaguar/Escko, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar tap

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipesand fittings

Providing and fixing white vitreous china flat back half stall urinal basin of 580x380x350mm with Flat White P.V.C automatic flushing cistern, of approved make with fittings, C.I./M.S. brackets, standard size of C.P. brass flush pipe, spreaders with unions and clamps complete, (all in C.P. brass) with waste fitting as per IS:2556, C.l trap with outlet grating and other couplings in C.P brass including painting of fittings and brackets, cutting and making good the walls and floors wherever required:One urinal basin with 5 litre P.V.C white automatic flushing cistern of approved quality.

Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to woooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT waste coupling for wash basin and sink of approved quality and colour. Waste coupling 38mm of 38mm length not less than 60gms

Providing and fixing PVC, waste pipe for sink or basin including P.V.C waste fittings complete. Semi rigid pipe 32mm dia

Providing and fixing CP brass towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arangement of approved quality colour and make (Prayag or equivalent)600mm long towel rail with total length of 645 width, 78mm wide and effective high of 88mm, weighing not less thant 190gms.

Providing and fixing CP brass toilet paper holder. C.P. Brass

Providing and fixing soap dish of C.P brass and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality colour and make, weight not less than 105gms (Prayag or equivalent)

Providing and fixing soil, waste and vent pipes PVC of approved brand ,100mm

PVC 75mm

Providing and fixing 100 mm sand cast iron grating for gully, floor or Nahani trap

Providing and fixing P.trap for English type w.c with washer and m.s claps complete job

Providing and fixing double equal plain junction of required degree 75x75x75 pvc as per

100x100x100 pvc as per

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes SOR 7.4 UV stablized and anti-microbialfusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fitings 1/C fixing the pipe with clamps at 1.00m spacing. This includes cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-charge. (concealed work including cutting chases and making good the walls etc.)

25mm OD nominal bore

32 mm dia nominal bore

40 mm dia nominal bore

Providing and fixing C.P brass bib cock of approved quality conforming to IS :8931 15 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions 30 Cm length 15mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixerand gyser points _of approved make conforming to IS : 8931 15 mm nominal bore

Providing and fixing C.P. brass close hole basin mixer piller tap of approved quality and make, weighing not less than 1.970 kg.15 mm nominal bore of standard back type.

Providing and installation of PUF (Puf Insulated Tanks ) with insulation thickness of 50 mm and density 40 kg/cu.m. UV protected with 0.5'c Change in stored water after 6 hours in continous 50'c or contionously in -20'C with capacity of 1000 Ltrs of Approved Brand As per the directions of engineer incharge Complete Job including carriage upto side of work.

Making connection of PPR. distribution branch with G.I.main of following sizes by providing and fixing tee,including cutting and threading the pipe etc. complete.20 to 32 mm nominal bore

Providing and fixing pvc gate valve with complete job 32mm dia.pipe.

Prioviding and fixing heat tape 33watt and insulation of pipe with nitrile tube ,taping with cello tape, rockwool 6inch per side ,wire mesh ,polythene ,tapping with cellotape aluminium sheet 26 guage cladding with dia complete Job .

Providing and fixing 35 ltr Geyzer(venus or approved quality ) incl. all fixture.

Providing and fixing 15 ltr Geyzer(venus or approved quality ) incl. all fixture.

carraige of sand/ Agg for an average lead of 20 Km by MT .

carraige of Stone . for an average lead of 15 Km by MT .

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. a ) 25mm Inclidung fan box, concealed box etc.

Septic Tank

Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres: asdirected by Engineer-in-charge.

All kind of soil @85%

(ii) Ordinatry rock .@15%

DisposalofMulba/ExcavatedEarthBeyond 50m (Lead upto 6Km) Outside Campus Area (CARRIAGEOFMATERIALSBy Mechanical Transport including loading, unloading and stacking)

Providing and laying position cement concrete of specified grade excluding the cost of centering and shuttering. All work upto plinth level 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) (crushed)

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1cement :6coursesand:12grade stone aggregate 20mm nominal size) upto plinth level with cementmortar 1:6 ( 1cement : 6course

Dry random rubble masonarywith hard stone in foundation & plinth using quarr stone with bond stone

Reinforced cement concrete work in beams, suspended floors ,roofs having slope up to( 15 degree)landings ,balconies ,shelves ,chajjas,lintals bands ,plain windows sills ,stair cases and spiral stair cases up to floor five level excluding the cost of centering ,shuttering ,finishing and reinforcement with 1:1.5:3(1cement:1.5coarse sand:3graded crushed stone aggregate 20mm nominal size

Providing & fixing upto floor five level precast cement concrete solid blocks including hoisting and setting in position in cement mortar 1:3 (1cement:3 coarse sand), cost of required centring, shuttering and curing complete 1:2:4 (1 cement : 2 coarse sand : 4 graded crushed stone aggregate 20 mm nominal size)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level Thermo Mechanically Treated bars of grade Fe 500D or more.

Centering and shuttering including strutting, propping etc. and removal of form for:Suspended floors, roofs, landings, balconies

Cement concrete flooring 1:2:4 (1cement:2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete,but excludingthecostofnosing of steps etc. complete.50mmthickwith 20mmnominal size stoneaggregate. 40 mm thick with 20mm nominal sizem stone aggregate

Supplying and fixingC.I. cover without frame for manholes: 560 mm diameter C.I. cover (heavy duty) the weight of the cover tobenot less than 108 kg

CEMENT PLASTER (IN COARSE SAND) 12mm Cement plaster of mix 1 : 4 ( 1 cement : 4 coarse sand) (PPC or cement with >25% flyash is recommended as per green building guildelines)

carraige of sand/ Agg for an average lead of 20 Km by MT .

carraige of Stone . for an average lead of 15 Km by MT .

Security Guard Room

Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres:

I) All Kinds of Soil @80%

(ii) Ordinatry rock .@10%

(iii) Hard rock(BP) @10%

Dry stone Pitching Excluding the cost of stones. in Horizontal on level

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level.1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) Crushed:

Random Rubble masonry with hard stone in foundation and plinth including leveling up with cement concrete 1:6:12 (1 Cement : 6 coarse sand : 12 graded stone aggregate 20mm nominal size) upto plinth level and curing complete with: 7.1.1 Cement mortar 1:6 (1 Cement : 6 coarse sand)

Providing and fixing upto five floor level precast cement concrete solid block including hoisting and setting in position with cement motar 1:6 1:3:6 (1 cement : 3 coarse sand : 6 graded crushed stone aggregate 20 mm nominal , cost of required centering shuttering and curing complete

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with. 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry , but excluding the cost of nosing of steps extra complete.50mm thick with 20mm nominal size stone aggregate Crushed:

15mm cement plaster on the side of single or half brick wall fiished with a floating coat of neat cement of mix : 1: 4( 1cement :4 fine sand)

Centring and shuttering including strutting, propping etc. and removal of form work complete.Foundations, footings, bases of columns etc. for mass concrete.

Walls (any thickness) including attached pilasters, buttresses, plinth andstring courses etc.

Lintel, beams, plinth beams,girders,bressumers and cantilever.

Suspended floors, roofs, landings, balconies and access platforms.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): 1st class kail wood

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for eparately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately)Second class kail wood 9.5.5.1 35 mm thick shutters

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, indows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : 9.7.2.2 Second class Kail wood

Providing and fixing 4mm glass pane incld. Beading etc complete.

Providing and applying white cement based putty of average thickness 2 mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complet

Distempering with 1st quality acrylic distemper (readymixed) having VOC contentlessthan50gms/litre,ofapprovedmanufacturer,ofrequiredshadeand colour complete, as per manufacturer's specification Two or more coats on new work

Rough cast plaster upto 10m height above ground level with a mixture of sand and gravel or crushed stone from 6mm to 10mm nominal size dashed over and including the fresh plaster in two layers , under layer 12 mm cement plaster in 1:4 ( 1 cement: 4 coarse sand ) and top layer 10 mm cement plaster with cement mortar 1:3 ( 1 cement: 3 fine sand ) mixed with 10% finely grounded hydrated lime by volume of cement.

Finishing walls with textured exterior paint of required shade :New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and includingpriming coat of exterior primer applied @ 2.20kg/10 sqm

6mm cement plaster to ceiling of mix 1:3 [1 cement, 3 fine sand]

Providing and fixing ISI marked oxidized M.S. tower bolt black finish, (Barrel type) with necessary screws etc complete

Providing and fixing ISI marked oxidized M.S. sliding door bolts with nuts and screws etc. complete : 300x16 mm

Providing and fixing ISI marked oxidized M.S. handles conforming to IS : 4992 with necessary screws etc. complete :125

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m.

Providing and fixing precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, omplete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing ridges or hips of width 60cm overall width plain G. S. sheet fixed with poymer coated J. or L hooks, bolts and nuts 8mm G. I. limpet and bitumen washers complete. 0.80 mm thick with zinc coating not less than 275gm /m2 specifications as per engineer in charge

French spirit polishing with Two or more coats on new works including a coat of wood filler

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 13755 of NITC.O, ORIENT, SOMANY, KAJARIA or equivalent make in colour such as White, Ivory, Grey, Fume Red, Brown laid on 20 mm thick bed of Cement Mortar 1: 4 ( 1 cement : 4 coa.rse sand) including pointing the joints with white cement and matching pigment etc., complete. In all colours, shades, except White, Ivory, Fume Red Brown

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required Orissa pattern W.C. pan of size 580x440 mm with integral type foot rest

Providing and fixing wash basin with C.I. / M.S. brackets 15 mm C.P brass pillar taps, Kingstone/ Gem/ Techno/ Parko/Jaguar/Escko, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar tap

Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

carraige of sand/ Agg for an average lead of 20 Km by MT .

carraige of Stone . for an average lead of 15 Km by MT .

Electricfication

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with thefollowing sizes of FRLS PVC insulated copper conductor, singlecore cable in surface/ recessed medium class PVC conduit asrequired. A ) 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

b ) 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

c ) 2X 10 sq. mm + 1X 6 sq. mm earth wire

d ) 4 X 16 sq. mm + 2 X 6 sq. mm earth wire

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. ( FOR INVERTOR )1x 1.5 sq.mm

1x2.5 sqmm

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excludin modular plate etc. as required. a) 5/6 A switch

3 pin 5/6 A socket outlet

Telephone Socket outlet

TV antenna socket outlet

Bell push

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2 No.s 3 pin 5/6 A modular socket outlet and 2 No.s 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) a ) 6 way (4 + 18), Double door

b ) 8 way (4 + 24), Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.A ) Single pole 6 /16 amp

Supply, installation , testing & commissioning of GI Electrode Earthing with 84mm dia and 3 meter length , with 3mm thick the electrode should be hot dip galvinised . The GI Electrode shall be pre filled with cristaline Conductive Material ( CCM ) . The GI electrode shall be surrounded with BEE MOIST compound to provide maximum contact between the electrode and compound should be eco - friendly GI Electrode Earthing should be eco - friendly GI Electorde Earthing should be maintinance free and does not require regular manual addition of water . The earthing pit should be covered with PVC cover.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Supplying and fixing following rating and breaking capacity and pole MCCB with thermagmetic release and terminal spreaders in existing cubical panel board including drilling holes in cubical panel making connections etc as required MCCB FP 400 Amp 50 KA

On load Change over switch 250 Amp

Fabrication, supplying , installation testing and commissioning of following pannel made out of 2mm thick M.S sheet , floor mounted , vermin & dust proof, indoors , duly painted with provsion for fixing of1 nos incomer MCCB, , MCCB type change over switch - 1 No including supply and fixing 2 set of Aluminium bus bar and strip for housing MCB,s 24 Nos , MF Digital Meter and other allied accessories as required ( Make as per annexure)

Supplying and fixing of following rating 240 /415 Volt " C" series miniature circuit breaker suitable for lighting and other loads of following poles in the existing MCB DB complete with connection , testing and commissioning.( Above to 32 Amp) a ) SPN 63 Amp

TPN 63 Amp

Supplying and fixing of 1.1 KV PVC insulated and PVC sheathed XLPE at power cable of following sizes on surface / surface cables tray , 0.50 mtr below ground level etc. as required including carriage upto site of work ( Make as per annexure enclosed) 150 Sqmm 3.5 core Armoured

Supplying and fixing of 120 watt LED Street Light complete with GI pipe bracket duly embeded along the parapet /wall. Wipro LR02-132-XXX-57-G2 or equivalent approved make

20 watt LED tube light fitting. LL20-221-XXX-65NE3 of wipro or equivalent make and model Philips/Crompton Greaves.

Supplying and fixing of Angle / Baten Holder with 9 watt LED Lamp polycarbonate including making complete connections etc. as required. ( Make as per annexure enclosed.)

Supplying and fixing of following electrical items suitable for operating on 240 /230 volts AC, 50 HZ supply , including connection etc. as required. Exhaust fan 250mm size ( Heavy duty) CG transair or equivalent approved make

Supplying, installation testing and commissioning of LED 2'x2' recess mounted fixture that delivers atleast 3000 lumens and wattage not more than 36 watt. The luminaries shall have a CRC a power coated body and a high efficiency diffuser. WIPRO CRCO10 RO 38HP57GL OR equivalent approved make.

Supply and fixing LED type down lighter 12 watt

Supply and fixing LED type down lighter 15 watt

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existingsurface/ recessed steel/ PVC conduit as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as require

Please Enable Macros to View BoQ information