RETENDER PW4/MS/181/19 own fund work Kadappakkada Market Maintenancein Dvn-17

Amount

15.23.1 : Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For thickness of tiles 10 mm to 25 mm

od45451/2019_2020 : Engaging Labour for dismantling the existing damaged rolling shutter and stacking the available materials as per the direction of engineer in charge

od45910/2019_2020 : Engaging labour for demolishing existing fully damaged PVC roofing sheet including all charges etc.complete

51.2.3 : Filling with Quarry Muck <br> Filling up low lying and water logged areas with local material/ quarry muck, spreading in layers, leveling the top at site and consolidation by ramming, etc complete for improving the CBR value of subgrade

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

11.19.4 : Chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand):Ordinary cement without any pigment

od31927/2019_2020 : Providing and laying factory made chamfered edge Cement Concrete paver blocks&lt;br&gt;in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength,&lt;br&gt;thickness &amp; size/ shape, made by table vibratory method using PU mould, laid in&lt;br&gt;required colour &amp; pattern over 50mm thick compacted bed of 6mm chips, compacting and&lt;br&gt;proper embedding/laying of inter locking paver blocks into the chips bedding layer&lt;br&gt;through vibratory compaction by using plate vibrator, filling the joints with sand and&lt;br&gt;cutting of paver blocks as per required size and pattern, finishing and sweeping&lt;br&gt;extra sand. complete all as per direction of Engineer-in-Charge.&lt;br&gt;80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.

4.1.3 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

10.6.3 : Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.80x0.90 mm M.S. laths with 0.90 mm thick to cover

12.47.1 : Providing & fixing UV stabilised fibre glass reinforced plastic sheet rooting up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8 mm dia G.I plain/ bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovings incorporating minimum 0.3% ultra-violet stabiliser in resin system under approxirnately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866. The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified.2 mm thick corrugate 2.5"or 4.2" or 6") or step-down (2' or 3" or 6") as specified.

14.54.1 : Painting with synthetic enamel paint of approved brand and manufacture of required colour to an give even shade:One or more coats on old work

Bidder Name

kollam corporation labour contract co operative society