NBDD/BS/SE /NIQ- 16 (EL) of 2020-2021

Amount

Supplying and fixing double door 4 WAY Vertical TPN MCB Distribution board for MCCB incomer with IP-42/43 protection, with 1 No. 160 A FP MCCB as incomer and 2 NOS 63A TP MCB, 2 NOS 32 A TP MCB as outgoing complete on angle iron frame on wall & mending good the damages to original finish incl. Inter connection with suitable size of copper wire and neutral link & provision for earthing attachment

Supplying and fixing double door 6 way TPN MCB Distribution board with IP-42/43 protectionwith 1 No. 63 A FP MCB as incomer and 18 nos. 6-32 A SP MCB as outgoing complete , concealed in wall after cutting the wall & mending good the damages to original finish incl. Inter connection with suitable size of copper wire and neutral link & provision for earthing attachment with following MCBs & MCB Isolator .

S & F 2+12 way double door IP-43 SPN MCB distribution board with 1 No. 40 A DP MCB as incomer and 10 no 6-32 A SP MCB as outgoing complete with Din Rail, Earth, Neutral & Phase Bars etc. to be partially recessed in wall with earthing attachment.

Supply 1.1 KV grade PVC Armoured XLPE insulated AL conductor cable . i) 3.5 core X 50 sq.mm.

Laying of cable from 3/3½ core 35 sqmm to 50 sqmm on wall/surface incl. S & F MS saddles with earthing attachment in 2 x 10 SWG GI (Hot Dip) Wire, making holes etc. as necy., mending good damages and painting

S & F compression type gland complete with brass gland, brass ring & rubber ring for dust & moisture -proof entry of XLPE/PVC armoured cables as bellow. i) 3.5 core X 50 sq.mm.

Finishing the end of following XLPE/PVC armoured cable by crimping method incl.S & F solderless socket (Dowels make,) tapes,anticorrosive paste & joining materials. i) 3.5 core X 50 sq.mm.

Distn. wiring in 22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed single core stranded copper wire (Brand approved by EIC) in 19 mm bore, 3 mm thick polythen pipe complete with all accessories embedded in wall to light/fan/call bell points with Modular type switch (Brand approved by EIC) fixed on Modular GI switch board with top cover plate flushed in wall incl. mending good damages to original finish a) Avg run 9 mtr.

Distn. wiring in 22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed single core stranded copper wire (Brand approved by EIC) in 19 mm bore, 3 mm thick polythen pipe complete with all accessories embedded in wall to 240 V 6A 5 pin plug point incl. S&F 240 V 6A 3 pin Modular type plug socket & Modular type switch (Brand approved by EIC) incl. S&F earth continuity wire, fixed on 4 Module GI switch board with 3/4 Module top cover plate flushed in wall incl. mending good damages to original finish 2x22/0.3 (Ph. & N) and 1x22/0.3 as ECC On Board.

Supply & Fixing 240 V, 6 A, 3 pin Modular type plug socket (Brand approved by EIC) with 6A Modular type switch, without plug top on 4 Module GI/PVC Modular type switch board with 3 Module top cover plate flushed in wall incl. S&F switch board and cover plate and making necy. connections with PVC Cu wire and earth continuity wire etc.

Supply & Fixing 240 V, 16 A, 3 pin Modular type plug socket (Brand approved by EIC) with 16A Modular type switch, without plug top on 4 Module GI /PVC Modular type switch board with top cover plate flushed in wall incl. S&F switch board and cover plate and making necy. connections with PVC Cu wire and earth continuity wire etc.

Supply of 250 V 300 mm. sweep,1400 rpm industrial type heavy duty (ISI)high speed exhaust fan.

Supply of 250 V 450 mm. sweep industrial type heavy duty (ISI)high speed exhaust fan.

Fixing only 300 mm dia exhaust fan after making hole in wall and making good damages and smooth cement finish etc. as practicable as possible and providing necy. length of PVC insulated wire and making connection.

Fixing only louver shutter/cowl on wall with necy. bolts & nuts (6 mm dia x 62 mm long)

Fixing on 450 mm dia exhaust fan after making hole in wall and making good damages and smooth cement finish etc. as practicable as possible and providing necy. length of PVC insulated wire and making connection.

Fixing only louver shutter/cowl on wall with necy. bolts & nuts (6 mm dia x 62 mm long)

S & F 250 V 1400 mm sweep AC ceiling fan complete with blades, canopy, down rod etc. having fixed with 2 nos ball bearing fixing the same, painting of down rod, connection by supplying 3×1.5 sq. mm stranded copper wire.

Supply and fixing 3/4"MS down rod For fixing the Ceiling Fan with all accessories.

Supply of high speed wall mounting bracket fan 240 V 400 mm sweep fixed with close mesh guard , pull chain arrangement for speed control and sturd and heavy duty blades for higher displacement of air .

Fixing only cabin fan on wall/ceiling by S&F rag bolts, nuts & washers (6 mm dia x 62 mm long) or as reqd. incl. S&F 24/0.20 PVC insulated flexible copper wire 0.5 mt. length

Supplying & Fixing iron beam fan clamp of two piece type, as per approved specification, fabricated from 40 mm x 9 mm MS sheet flat suitable for beam having flange upto 150 mm wide – (As per Drawing no. 476 of PWD Specification Book – May 1991)

Supply & Fixing 240V, Modular Socket (2 Module) type fan regulator (Step type) (Brand approved by EIC) on existing Modular GI switch board with top cover plate incl. making necy. connections etc.

Supply of 240V LED tube light mounting rail lighting luminaire to be fixed on ceiling for TLED lamp with necessary connection and earthing attachment .

Fixing only Single/twinfluorescent light fitting suspended 25 cm bellow the ceiling with 2 No. 20 mm dia EI conduit (14 SWG) supports incl. S&F EI conduit, ball socket/socket type ceiling plate and connecting the length of PVC insulated wire and painting etc. as required by 2x24/0.20 mm (1.5sqmm) flexible copper wire of 1.10 mt. length.

Supply of surface mounted 18 watt LED down lighters which range is a breakthrough technology and reliable heat management to deliver a long lasting efficient solution .

Supply of LED Bulkhead that fits in vartiety of applications and serves as simple energy efficient alternative to CFL/incandescent bulkhead luminaires

Supply & Fixing angular batten holder (Anchor) on 75mm dia PVC round block / round bakelite on wall/ceiling with 10 W LED lamp.

Fixing only bulk head /ceiling fitting on wall /ceiling by screws etc.

S & F 70 W Energy saving ,enviromental friendly,long life,exclusive innovative die-cast aluminium IP65 flood light ,suitable for highlighting architectural façade and genaral purpose lighting.

Supplying and fixing 19 mm dia and 3 mm thick polythene pipe complete with fittings as necy. under ceiling/beam, bound with 22 SWG GI binding wire incl. supplying and drawing 1x18 SWG GI Wire as fish wire inside the pipes and fittings and providing 50 mm dia disc of MS sheet (20 SWG) having colour paint at one face fastened at the load point end of the polythene pipe with fish wire (synchronizing with roof/beam casting work of building construction)

Supplying and Drawing 1.1 KV single core stranded 'FR' PVC insulated & unsheathed single core stranded copper wire of the following sizes in the prelaid polythene pipe by the GI fish wire and making necy. connection as required. a) 4×10 sq.mm. + 2×6 sq.mm.

b) 2×10 sq.mm. + 1×6 sq.mm.

d)2 x 36/0.3 (2.5 sqmm) + 1 x 22/0.3 (1.5 sqmm)

e)3 x 22/0.3 (3x1.5 sqmm)

Supply & Fixing of perforated GI cable tray with perforation not more than 17.5% suspended from ceiling incl. S&F GI connector, 6mm dia MS suspender, bolts & nuts, steel fastener etc. as required of the following size. Incl. Al painting of MS support. 200x50x1.25mm (18SWG)

300x50x1.25mm (18SWG)

i) Earthing with 50 mm dia GI pipe (ISI-M) 3.64 mm thick × 3.04 mtr long and 1 × 4 SWG (Hot dip) wire 4 mtr long) 13 mm dia × 80 mm long GI bolts double washers incl. S & F 15 mm dia GI pipe protection (1 mtr long) to be filled with bitumen party under the ground level and partly above ground level driver to an average depth of 3.65 metre below the ground level & restoring the surface duly rammed.

S & F earth bus bar of GI (Hot Dip) MS flat of 50 mm × 6 mm on wall is having clearance of 8 mm from wall including providing drilled holes on the bus bar complete with GI bolts, nuts, washers spacing insulators tc. As required.

Extra for providing masonery enclosure on the top of the earth electrode of overall size 86.36 cm x 86.36 cm x 46 cm deep (below Ground level) complete with cemented brick work(1:6) of 25 cm width duly plastered with cement morter (inside) CI hinged inspection cover of size 36.56 cm x 35.56 cm with locking arrangement, GI reducer including drilling of 46 nos. 12 mm dia holes on the GI pipe including Extra for treatment of soil by using salt & charcoal or coke for plate electrode

Installation of security light: Fixing outdoor type fluorescent/SV/MV light fitting on pole including S&F 40 mm dia x 1.68 mts. long GI Pipe (ISI-Medium) bracket with 40 mmx10 mm thick, MS clamp etc. and providing wiring with 2x1/1.40 PVC insulated and sheathed wire (single core) from loop box at the base of pole to light fiting through pole & bracket (without control switch) including making connections & painting

Supplying & Fixing GI waterproof type looping cable box size 200x150x100 mm deep having 4 mm thick comprising of one 250 V 15 A kit-kat fuse unit, one NL on porcelain insulator, one compression type brass cable gland for upto 2- core 16 sqmm PVC/A cable and having lined with rubber gasketted GI top cover with brass machine screws etc., earthing terminal with lug, on steel tubular pole near base, including S&F 40x6 mm thick, MS clamps with bolts, nuts etc. including painting with anticorrosive paint

Supply of 1.1 KV grade PVC /A aluminium conductor2 core X 10 sq.mm ( KEI/Crystal/Polycab)

Laying of cable upto 2 core 25 sqmm on wall/surface incl. S & F MS saddles with earthing attachment in 10 SWG GI (Hot Dip) Wire, making holes etc. as necy. mending good damages and painting

S & F compression type gland complete with brass gland, brass ring & rubber ring for dust & moisture -proof entry of XLPE/PVC armoured cables as bellow. i)2 core X 10 sq.mm.

Finishing the end of following XLPE/PVC armoured cable by crimping method incl.S & F solderless socket (Dowels make,) tapes,anticorrosive paste & joining materials. i) 2 core X 10 sq.mm.

Supply & laying of 3 X 2.50 sq. mm PVC insulated copper conductor FR wire from loop box to fittings in 15 mm dia polythene pipe including connection as required.

Supplying and fixing 4 WAY MCB SS enclosure with IP-20/30 protection, powder coated including 2 NOS 6-32A two pole MCB, concealed in wall after cutting the wall & mending good the damages to original finish incl. painting, connection & provision for earthing attachment

Supply of 120 W LED Street light luminaire with high power LED

Sinking of 128x80mm Deep Tube well by Odex-115 method: Drilling borehole by Rig machine with Odex-115 (Simultaneous driving of casing pipe) method of drilling through any kind of soil, boulder, rock etc upto the desired depth by making all necessary arrangement. a) G.L. To 50 Mtr.

b) 50 Mtr. To 100 Mtrs.

Lowering and placing of filter assembly of 3 mtr length.

Exration and partening off the cassing pipe upto the required length to open the filter (approx 3 mtr length).

Development of the tube well by Air Compressor upto the satisfaction of EIC.

Supply of the following materials for the tube well:- a) 128 mm ID/139 mm OD MSERW fin cut pipe

b) 80 mm dia x 3 Mtr long HDPE/Other suitable filter.

c) Casing Shoe.

d) Packer assembly.

Supply and Installation of 3 HP Submerssible pump motor set suitable for 125 mm dia deep tube well capapable for discharging 20000 LPH of Clear water at a total head of 48 mtr having a discharging outlet of 50 mm dia .

supply of PVC insulated and PVC sheathed cable with Electrolytic Grade Annealed Copper conductor having 3 core 4 sqmm flate for Submersible pump motors voltage up to and including 1100V as per IS: 694:1990.

Supply, fitting, fixing 50 mm dia G.I. Pipe (ISI-M) column pipe for submersible pump lowering having 3-mtr average length including special threading in Leathe and S & F one Tata GI socket.

Supply and fixing 4" dia Pressure Gauge including nipple, valve etc with other jointing materials.

Making of brick piller of suitable size with neat cement plastering for supporting lead/plumbing line as per instruction of EIC.

S & F of 50 mm dia Non-return valve (horizontal) with jointing materials (ISI approved Zoloto make).

S & F of G.M. Peets valve including all necessary jointing materials (ISI approved) for the following size: 50 mm dia.

S&F 50 mm dia check valve bwith flanged as required

S & F suitable size of M.S. Flat clamp for holding the column pipe, pump motor in the tube well with necessary nuts, bolts, washer as per direction of EIC.

S & F of well cover suitable for tube well.

S & F 20 mm dia G.I. Pipe (Jindal-M) for protection of cable.

supply ,installation ,testing & commissioning of three phase 415 V 50 HZ ,3HP submersible pump controllers with Single phase preventer including wideband coil and relay current rang 9-14 (A)

Supply, fabrication & installation of header assembly made of 150 mm dia 1.2 meter long black MS pipe having both sides sealed by welding provision for with MS sheet for 1 No. 50 mm dia inlet & 4 nos 50 mm dia outlet to be fixed on 50 & 40 mm short pieces welded with 150 mm header including 4 nos gun metal wheel wash out line with provision for pressure gauge and 1/2'' Fullway valve,nipple and presure gauge to be fixed on Header with all supporting arrangement & painting etc as per direction of EIC.

Supply & laying 50 mm dia GI pipe (Class-B) medium mainly U/G trench with all jointing materials as per direction of EIC.

S & F of G.I. Accessories (R-brand) ISI approved with all jointing materials: a) 50 mm dia Bend.

b) 50 mm dia Elbow.

c) 50 mm dia Nipple.

d) 50 mm dia Union.

e) 50 mm dia Socket (Tata make).

f) 50 mm dia Elbow, Union, Nipple, Socket etc for suction line connection.

Making connection of delivery pipe line to O.H. Tank with existing line with jum nut, nipple, washer etc. Including all jointing materials.

Collecting sample of water for bacteriological and chemical test from any depth at any time during execution of work including hire and labour charges for tools and plants and sterilising the equipments, paying all charges and fees, testing etc. complete in all respect as per direction.

Making connection of delivery pipe line to O.H. Tank with existing line with jum nut, nipple, washer etc. Including all jointing materials.

SUBRATA DEB ROY

M/S TECHNO INDIA