REPAIR AND MAINTENANCE OF WOODEN AND STEEL FURNITURES AND GI CHARPOY INCLUDING PAINTING POLISHING AT BINNAGURI UNDER GE NORTH BINNAGURI

Amount

Repairs to Chair Writing for the following :- Removing old unserviceable fitting and fixture of Chair Writing without disturbing to the other parts such as legs,rails, stiffiners, Hand rest etc and supply and fixing with new items of Best quality 1st Class HW (Teak)) and minor repair applying French Polishone or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No. FD-20(M)/ 280)

Front legs. 1st class hardwood (TeaK)

Rear legs 1st class hardwood (TeaK)

Right/ left side rails of seat frame . 1st class hardwood (TeaK)

Front /rear rails of seat frame .1st class hardwood (TeaK)

Stiffener.bottom 1st class hardwood (TeaK)

Stiffener back rest 1st class hardwood (TeaK)

Arm rest. 1st class hardwood (TeaK)

Taking out unserviceable plastic cane from seat frame of Chair writing and Supply and fixed for weaving the seat of Chair in Godrej pattern with new 2 mm wide half round 0.40mm thickness and 4mm for border approved quality complete all as specified and shown in drawing. (Drawing No. FD-20 (M)/280)

Repairs to Chair dining for the following :- Removing old unserviceable fitting and fixture of Chair dining without disturbing to the other parts such as legs,rails, stiffiners etc and supply and fixing with new items of Best quality 1 st class hardwood (Teak) and minor repair applying French Polishone or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No. FD- 16(M)/228/279/1105)

Front legs. 1st class hardwood (TeaK)

Rear legs 1st class hardwood (TeaK)

Right/ left side rails of seat frame . 1st class hardwood (TeaK)

Front /rear rails of seat frame .1st class hardwood (TeaK)

Stiffener back rest 1st class hardwood (TeaK)

Taking out unserviceable plastic cane from seat frame of Chair dining and Supply and fixed for weaving the seat of Chair in Godrej pattern with new 2 mm wide half round 0.40mm thickness and 4mm for border approved quality complete all as specified and shown in drawing. (Drawing No. FD-16(M)/228/279)

Repairs to Chair wooden bottom without arms for the following :- Removing old unserviceable fitting and fixture of Chair Writing without disturbing to the other parts such as legs,rails, stiffiners, Hand rest etc and supply and fixing with new items of Best quality 1st Class HW (Teak)) and minor repair applying French Polishone or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No. FD-56(M)/ 225)

Front legs. 1st class hardwood (TeaK)

Rear legs 1st class hardwood (TeaK)

Right/ left side rails of seat frame . 1st class hardwood (TeaK)

Front /rear rails of seat frame .1st class hardwood (TeaK)

Stiffener.bottom 1st class hardwood (TeaK)

Stiffener back rest 1st class hardwood (TeaK)

Seat Plywood (Make-Green Ply/Kit Ply,Century/Bhutan Board) 6mm thick, 4 No ply, ISI marked conforming to IS: 303-1989

Repairs to Chair Easy for the following :- Removing old unserviceable fitting and fixture of Chair Easy without disturbing to the other parts such as legs,rails, stiffiners, Hand rest etc and supply and fixing with new items of Best quality 1st Class HW (Teak) and minor repair applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No. FD- 17)M)/ 229)

Front legs. 1st class hardwood (TeaK)

Rear legs 1st class hardwood (TeaK)

Top rails .1st class hardwood (TeaK)

Side Top rails (Left/Right) .1st class hardwood (TeaK)

Rear Top rails (Left/Right) .1st class hardwood (TeaK)

Side bottom rails (Left/Right) .1st class hardwood (TeaK)

Front/ Rear bottom rails.1st class hardwood (TeaK)

Arm rest. 1st class hardwood (TeaK)

Taking out unserviceable plastic cane from seat frame of Chair Easy and Supply and fixed for weaving the seat of Chair in Godrej pattern with new 2 mm wide half round 0.40mm thickness and 4mm for border approved quality complete all as specified and shown in drawing. (Drawing No. FD-20 (M)/280)

Repairs to Table 900 mm x 600 mm x 760 mm (Table 3'x2') with Drawer for the following :- Removing old unserviceable fitting and fixture of Table 3' x 2' with and witout drawer without disturbing to the other parts such as legs,rails, top,stiffiners, Drawer etc and supply and fixing with new items of Best quality 1st class HW (Teak) and minor repair applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No: FD : 42(M)/55(M)/231/ 284

Top of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 5mm thick timber beading around the edging.

Long rail 1st class hardwood (TeaK)

Side rails 1st class hardwood (TeaK)

Legs 1st class hardwood (TeaK)

Stiffeners 1st class hardwood (TeaK)

Drawer as per existing shape and size made out of 1st class hardwood (Teak) complete all as specified and as directed.

25 mm dia chroumium plated Knob with brass nuts and bolts

Repairs to Table 900 mm x 600 mm x 760 mm (Table 3'x2') without Drawer for the following :- Removing old unserviceable fitting and fixture of Table 3' x 2' with and witout drawer without disturbing to the other parts such as legs,rails, top,stiffiners, Drawer etc and supply and fixing with new items of Best quality 1st class HW (Teak) and minor repair applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No: FD : 42(M)/55(M)/231/ 284

Top of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 5mm thick timber beading around the edging.

Long rail 1st class hardwood (TeaK)

Side rails 1st class hardwood (TeaK)

Legs 1st class hardwood (TeaK)

Stiffeners 1st class hardwood (TeaK)

Repairs to Table Centre for the following :- Removing old unserviceable fitting and fixture of Table centre without disturbing to the other parts such as legs,rails, top,stiffiners etc and supply and fixing with new items of Best quality 1 st class hardwood (Teak) and minor repair applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No: FD: 29(M)/235/ 274)

Top of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4mm thick 1st class haedwood beading around the edging.

Legs 1st class hardwood (TeaK)

Long rails 1st class hardwood (TeaK)

Side rails 1st class hardwood (TeaK)

Repairs to Table dining 8 person for the following :- Removing old unserviceable fitting and fixture of Table Dining 6 Person without disturbing to the other parts such as legs,rails, top, stiffiners etc and supply and fixing with new items of Best quality 1st class hardwood (Teak) and minor repair applying of French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No: FD : 30(M)/273)

Top of 18 mm thick particle board conforming to IS-3087-2005 with 1 mm thick plastic laminated sheet teak face shead on top using approved adhesive including 4mm thick 1st class hardwood (Teak) beading around the edging.

Long rail 1st class hardwood (TeaK)

Side rails 1st class hardwood (TeaK)

Legs 1st class hardwood (TeaK)

Repairs to Table dining 6 person for the following :- Removing old unserviceable fitting and fixture of Table Dining 6 Person without disturbing to the other parts such as legs,rails, top, stiffiners etc and supply and fixing with new items of Best quality 1st class hardwood (Teak) and minor repair applying of French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No: FD :30(M)/239/273 )

Top of 18 mm thick particle board conforming to IS-3087-2005 with 1 mm thick plastic laminated sheet teak face shead on top using approved adhesive including 4mm thick 1st class hardwood (Teak) beading around the edging.

Long rail 1st class hardwood (TeaK)

Legs 1st class hardwood (TeaK)

Side rails 1st class hardwood (TeaK)

Repairs to Table Drassing Ladies for the following :- Removing old unserviceable fitting and fixture of Table drassing Ladies without disturbing to the other parts such as top,side, glass, mirror,knob etc and supply and fixing with new items and 5 mm thick wooden beading whereever required and minor repair applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No. FD-32(M)/ 251)

Legs 1st class hardwood (TeaK)

Top of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 5 mm thick timber beading around the edging.

Side of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 5 mm thick timber beading around the edging.

Bottom of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 5 mm thick timber beading around the edging.

Back of 6mm thick, 4 No ply, ISI marked conforming to IS: 303-1989 complete all as specified and as directed.

Mirror frame made out of 1st class hardwood (Teak)

Drawer 6mm thick, 4 No ply, ISI marked conforming to IS: 303-1989 front side with 18 mm thick pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 one No 25mm knob of required colour complete all as specified and as directed.

25 mm dia chroumium plated Knob with brass nuts and bolts

Aluminum channel for sliding glass with 5 mm thickness ordinary glass

Mirror 5.5 mm thick electro copper plated with 6mm thick plywood on back side with key plate (Modi/Atul Saint Gobbin )

Repairs to Table Drassing Gents with mirror for the following :- Removing old unserviceable fitting and fixture of Table drassing Ladies without disturbing to the other parts such as top,side, glass, mirror,knob etc and supply and fixing with new items and 5 mm thick wooden beading whereever required and minor repair applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No. FD- 31(M)/230)

Top of 12mm thick, 9 No ply, ISI marked conforming to IS: 303-1989 fixed with 5 mm thick timber beading around the edging and cover with 1mm thick plastic laminated sheet teak face colour fixed approved adhisive.

Back of 12mm thick, made out of 1st class hardwood (Teak)

Drawer 6mm thick, 4 No ply, ISI marked conforming to IS: 303-1989 front side with 18 mm thick pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 one No 25mm knob of required colour complete all as specified and as directed.

25 mm dia chroumium plated Knob with brass nuts and bolts

Bottom of 12 mm thick made out of 1st class hardwood (Teak)

Sides of 12 mm thick made out of 1st class hardwood (Teak)

Back of 6mm thick, 4 No ply, ISI marked conforming to IS: 303-1989 complete all as specified and as directed.

Mirror 5.5 mm thick electro copper plated with 6mm thick plywood on back side with key plate (Modi/Atul Saint Gobbin )

Mirror frame made out of 1st class hardwood (Teak)

Repairs to Side board for the following :- Removing old unserviceable fitting and fixture of side board without disturbing to the other parts such as top,legs,side, top,drawers etc and supply and fixing with new items with 1st class hardwood (teak) and 4mm thick 1st class hardwood beading whereever required and minor repair applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No: FD: 26(M)/241/ 1112)

Legs 1st class hardwood (TeaK)

Bottom 18 mm thick pre-lamintated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4mm thick timber beading around the edging complete all as specified and as directed.

Shutter 18 mm thick pre-lamintated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4mm thick 1st class hardwood (Teak) beading around the edging. with one knob 25mm dia complete all as specified and as directed.

Back Plywood (Make-Green Ply/Kit Ply,Century/Bhutan Board) 6mm thick, 4 No ply, ISI marked conforming to IS: 303-1989

Long rail of bottom 1st class hardwood (TeaK)

Short rail of bottom 1st class hardwood (TeaK)

Top of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4mm thick 1st class harwood (Teak) beading around the edging.

Drawer 18 mm thick pre-lamintated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4mm thick 1st class hardwood beading around the edging and 6mm thick plywood bottom with one knob 25mm dia complete all as specified and as directed.

Side of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 5mm thick timber beading around the edging.

Inside partition 18 mm thick pre-lamintated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4mm thick 1st class hardwood beading around the edging with one knob 25mm dia complete all as specified and as directed.

Shelve 18 mm thick pre-lamintated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 5mm thick timber beading around the edging. complete all as specified and as directed.

25 mm dia chroumium plated Knob with brass nuts and bolts

Removing of existing unserviceable nylon newar from charpoy , tightening the frame and Supply and fixed new ply wood 12mm thick BWR, 7 No ply, ISI marked, conforming to IS: 303-1989,including three stiffener of size (900 x 50 x 5mm mild steel flat iron and applying two coats of black synthetic paint over a coat of zinc chrome metal primer (size Approx 1950 mm x 900 mm) with 6mm dia 65mm long nut & bolts with washer (total 10 Nos) including drilling 03 Nos holes on each long rails and 02 Nos holes on short rails all as specified and as directed. (Drawing No: FD: 220 )

Removing of existing unserviceable plywood top and Supply and fixed new ply wood 12mm thick BWR, 7 No ply, ISI marked, conforming to IS: 303-1989 (size Approx 1950 mm x 900 mm) with three stiffener of size 900mm 50mm x 6mm MS flat iron and applying two coats od black synthetic enemal paint over a coat of zinc chrome metal primer and 6mm dia 75mm long nut & bolts in support counter sunk on long rail of GI charpoy complete all as specified and as directed. (Drawing No: FD: 220 )

Taking out broken unserviceable long rails from Charpoy GI pipe and Supply and fixing new short rails 900 mm long duly threaded at both end out of GI tube 32mm dia medium grade all as spacified (Drawing No: FD: 220 )

Taking out broken unserviceable shortrails from Charpoy GI pipe and Supply and fixing new long rails 1940 mm long duly threaded at both end out of GI tube 32mm dia medium grade all as spacified (Drawing No: FD: 220 )

Taking out broken unserviceable leg from Charpoy GI pipe and Supply and fixing new leg duly threaded at both end out of GI tube 32mm dia medium grade all as spacified (Drawing No: FD: 220 )

Taking out unserviceable short rails from Charpoy GI pipe and making short rails for GI charpoy made out of from broken long rails obtained from Sl No.15 above including cutting & threading rails and fixing in replacement all as spacified and directed. (Drawing No: FD: 220 )

Taking out unserviceable legs from Charpoy GI pipe and making leg for GI charpoy made out of from broken short rails obtained from Sl No.25 above including cutting & threading rails and fixing in replacement all as spacified and directed. (Drawing No: FD: 220 )

Taking out unserviceable elbow and Supply and fixing new GI elbow 32mm dia, three way medium grade, ISI marked all as spacified and directed. (Drawing No: FD: 220 )

Taking out unserviceable check nut from long rails and Supply and Fixing new check nuts of 6mm wide, 32mm dia all as specified and as directed. (Drawing No: FD: 220 )

Taking out old rusted/damaged/broken flat iron support of chapoy and supply and fixed new mild steel flat iron of size 25 x 3 mm thickness existing shape with GI washer fixed at clamp at bottom including painting with two coats of synthetic enamel paint over a coat of metal primer complete all as specified and as shown on drawing. (Drawing No. FD-220).

Taking out old damaged/broken wooden shoes from chapoy and supply and fixed new 2nd class hardwood (well seasoned) shoe of existing shape and size and fixed with screw at bottom of chapoy complete all as specified and as shown on drawing. (Drawing No. FD-220).

Removing of old PVC/ rubber shoe from various type of Tables/ chairs and supply and fixed new rubber/ PVC shoes as per existing size and shapes complete all as specified an das directed.

Material and labour for preparing & polishing wooden and wood based materials of any description and of any lenghth and width and applying french polish to furniture articles as specified with one or more coat till glossy finish achieved including filler as required all as specified in particular specifications and as shown on drawing and as directed by Engineer-in-Charge for the following wooden furniture:-

Chair Writing (Drawing No. FD- 20(M)/ 280)

Chair Dining (Drawing No. FD- 16(M)/228//279 )

Chair wooden bottom (Drawing No. FD-56(M)/225)

Chair Easy (Drawing No. FD-17/229)

Table wooden with drawer 900 mm x 600 mm x 760mm (Drawing No. FD- 41(M) 283)

Table wooden without drawer 900 mm x 600 mm x 760mm (Drawing No. FD- 42(M)/55(M)/ 231/284)

Table Dining 8/6 persons (Drawing No. FD- 30(M) /239/ 273)

Table dressing ladies with mirror (Drawing No. FD- 32(M) 251)

Table dressing gents with mirror (Drawing No. FD- 31(M) 230)

Side Board (Drawing No. FD- 26/241/ 1112)

Table Centre (Drawing No. FD- 29(M)/235/ 274)

STEEL FURNITURE Taking down existing unserviceable table top 900 mm x 600 mm with and without drawer Steel and supply and fixed new Top of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4 mm thick teak wood beading around the edging all complete specified shown on drawing & directed. (Drawing No. FD 1007/1008)

Material and labour for spot welding in repairs not exc 2.50cm in length of broken steel frame of Table complete all as specified and as shown in drawing. (Drawing No. FD 1007) (Note : Material to be weled not to exceeding 2.00mm in thickness)

Taking down existing unserviceable lock from drawer and supply and fixed with new steel lock 6 (six) lever for drawer with duplicate key in same position with new screws complete all as specified and as shown on drawing. (DRAWING No. FD-1008 )

Taking down existing unserviceable table top 900 mm x 900 mm with and without drawer Steel and supply and fixed new Top of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4 mm thick teak wood beading around the edging all complete specified shown on drawing & directed. (Drawing No. FD 1009)

Removing of unserviceable side/front/rear rail of 25 mm x 25 mm square tube mild steel 1.6 gauge and supply and fixed new side/front/rear rail of same size at the same position by welding as per drg and welding to the broken frame when ever required complete all as directed.

Removing of unserviceable/s legs of size 760 mm long 25 mm x 25 mm square tube mild steel 1.6 gauge and supply and fixed new legs of same size at the same position by welding as per drg and welding to the broken frame when ever required complete all as directed.

Material and labour for spot welding in repairs not exc 2.50cm in length of broken steel frame of Table complete all as specified and as shown in drawing. (Drawing No. FD 1009) (Note : Material to be weled not to exceeding 2.00mm in thickness)

Taking down decayed top from Table dining ORs and supply and fixing new top 18 mm thick pre-laminated particle board, Grade II Type I exterior grade conforming to IS-12823-2006 with 4mm thick teak wood beading all around the edging complete all as specified and as directed. (Drawing No. FD-165(M)

Material and labour for spot welding in repairs not exc 2.50cm in length of broken steel frame of chair verandah complete all as specified and as shown in drawing. (Drawing No. FD- 165(M). Note : Material to be weled not to exceeding 2.00mm in thickness)

Taking down existing unserviceable Teapoy Verandah top and supply and fixed new Top of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4 mm thick teak wood beading around the edging all complete specified shown on drawing.(Drawing No. FD 35(M)/255)

Material and labour in repair to broken frame leg of teapoy verandah by spot welding not exc 2.50cm in length complete all as specified and as directed. (Drawing No. FD 35(M)/255) (Note : Materials to be welded not exc. 2.50 cm in thickness).

Material and labour for spot welding to damaged/broken seat frame of chair CB without Arm/ with arm complete all as specified and shown on drawing. (Drawing No. FD-75(M). (Note : length of each spot welding will not exceed 4 cm in length and 2 mm in thichness).

Taking out old rusted/damaged/broken flat iron support of chair CB steel with Arms / without Arm and supply and fixed new mild steel flat iron of size 20 x 5mm, 75mm long to bottom of steel frame in support of wooden seat frame duly welded with making hole for fixing screw complete all as specified and as shown on drawing. (Drawing No. FD-75(M).

Taking out old damaged/broken arm rest and supply and fixed new arm rest in the same position as per existing shape and size made out of well seasoned first class hard wood ‘Teak ’ timber including applying two coat of black paint over wood filler on all exposed new wooden surfaces after preparation of new wooden surfaces complete all as specified and as shown on drawing. (Drawing No. FD-75(M).

Taking out unserviceable seat frame of Chair CB with Arm and Supply and fixed Seat frame made from Teak wood well seasoned and termite treated, with making holes of weaving slightly rounded on the edges and applying two coat of black paint over wood filler on all exposed new wooden surfaces of seat frame shall be painted with high glossy paint after preparation of new wooden surface and weaving with new cane seat and back in "Godrej" pattern with 2mm wide plastic cane for main canning and border with 3.5-5 mm cane bordering and 0.4mm thick gola type weighing not less than 6 gms per 10 running meters complete all as specified & as directed and as shown on drawing.complete all as specified and shown in drawing. (Drawing No. FD-75(M).

Taking out unserviceable back frame of Chair CB with Arm and Supply and fixed Back frame made from Teak wood well seasoned and termite treated, with making holes of weaving slightly rounded on the edges and applying two coat of black paint over wood filler on all exposed new wooden surfaces of back frame shall be painted with high glossy paint after preparation of new wooden surface and weaving with new cane seat and back in "Godrej" pattern with 2mm wide plastic cane for main canning and border with 3.5-5 mm cane bordering and 0.4mm thick gola type weighing not less than 6 gms per 10 running meters complete all as specified & as directed and as shown on drawing.complete all as specified and shown in drawing. (Drawing No. FD-75(M).

Taking out unserviceable seat frame of Chair CB without Arm and Supply and fixed Seat frame made from Teak wood well seasoned and termite treated, with making holes of weaving slightly rounded on the edges and applying two coat of black paint over wood filler on all exposed new wooden surfaces of seat shall be painted with high glossy paint after preparation of new wooden surface and weaving with new cane seat in "Godrej" pattern with 2mm wide plastic cane for main canning and border with 3.5-5 mm cane bordering and 0.4mm thick gola type weighing not less than 6 gms per 10 running meters complete all as specified & as directed and as shown on drawing.complete all as specified and shown in drawing. (Drawing No. FD-75(M).

Taking out unserviceable back frame of Chair CB without Arm and Supply and fixed Back frame made from Teak wood well seasoned and termite treated, with making holes of weaving slightly rounded on the edges and applying two coat of black paint over wood filler on all exposed new wooden surfaces of seat shall be painted with high glossy paint after preparation of new wooden surface and weaving with new cane seat in "Godrej" pattern with 2mm wide plastic cane for main canning and border with 3.5-5 mm cane bordering and 0.4mm thick gola type weighing not less than 6 gms per 10 running meters complete all as specified & as directed and as shown on drawing.complete all as specified and shown in drawing. (Drawing No. FD-75(M).

Taking out unserviceable plastic cane of chair Verandah seat and back and supply and fixing for weaving the seat and back of Chair Varandah in Godrej pattern with new 4 mm wide half round approved quality cane on steel surface of chair complete all as specified and as directed. (Drawing No. FD-19(M)/256/359)

Material and labour for spot welding in repairs not exc 2.50cm in length of broken steel frame of chair verandah complete all as specified and as shown in drawing. (Drawing No. FD- 19(M)/256/359) (Note : Material to be weled not to exceeding 2.00mm in thickness)

Material and labour in repair to broken/damaged bottom leg of locker bed side steel by spot welding complete as specified and as directed. (Drawing No. FD-257/1029) (Note: Thickness of metal to be welded shall not exceed 2mm.)

Taking out loose shelf from its position of Almirah large steel and re-fixing the same rigidly after minor repairs by providing new clips, nuts & bolts of existing size as required complete all as directed. ( Drawing No. FD-67(M)/FD-1031)

Taking down existing unserviceable leg (Right/Left) of Locker bed side steel and supply and fixed with new Leg of size 450 mm x 80 mm x 100 mm made out of 1mm Mild steel sheet in same position and applying two coatss of Synthetic enamel paint (1st quality) over a coat of red oxide zinc chrome primer complete all as specified and shown on drawing. (Drawing No. FD-257/1029)

Taking out loose shelf from of locker Bed Side Steel and refixing the same position rigidly after minor repairs by providing new clips, nut and bolts as required complete all as directed. (Drawing No. FD-257/1029)

Taking out existing unserviceable hasp and stapple and Supply and fixed new hasp and staple of size 100 mm x 20 mm x 3 mm Chromium plated Hasp and staple to front shutter of approved make and design complete all as specified and as shown on drawing (Make :- Mowjee or Classic) (Drawing No. FD-257/1029)

Material and labour in repairing of existing unserviceable hinges by spot welding and make it functional by providing pin/greasing etc. complete all as directed. (Note :-Each spot welding shall not be more than 2.5cm in length and materials to be welded not exceeding 3mm in thickness.) (Drawing No. FD-257/1029)

Taking out of unserviceable old handles from the front of shutter and Supply and fixed new 115mm long chrome plated handle of approved make and design complete all specified and as shown on drawing. (Drawing No. FD-257/1029)

Taking out of old unserviceable broken curtain rod including brackets and Supply and fixed new curtain rod of aluminium 19/20mm dia, 1.5 mm wall thickness with steel brackets both sides in the same position by spot welding including painting with applying two coat of Olive Green synthetic enamel paint (1st quality over a coat of red oxide zinc chrome primer by spray machine over steel brackets after preparation of new steel surfaces complete all as specified and as shown on drawing. (Drawing No. FD-257/1029)

Taking out old unserviceable/damaged bottom shelf and Supply and fixed new bottom shelf as per existing shape and size made out of 1mm thickness plain mild steel sheet and fixed in the same position with shelf clips, nuts & bolts etc including applying painting with two coat of Olive Green synthetic enamel paint (1st quality) over a coat of red oxide zinc chrome primer by spray machine before fixing and after preparation of new steel surfaces complete all as specified and shown on drawing. (Drawing No. FD-257/1029)

Taking out old unserviceable/damaged intermediate shelf and Supply and fixed new intermediate shelf as per existing shape and size made out of 1mm thickness plain mild steel sheet and fixed in the same position with shelf clips, nuts & bolts etc including applying painting with two coat of Olive Green synthetic enamel paint (1st quality) over a coat of red oxide zinc chrome primer by spray machine before fixing and after preparation of new steel surfaces complete all as specified and shown on drawing. (Drawing No. FD-257/1029)

Taking out old unserviceable/damaged inner partition and Supply and fixed new inner partition as per existing shape and size made out of 1mm thickness plain mild steel sheet and fixed in the same position with shelf clips, nuts & bolts etc including applying painting with two coat of Olive Green synthetic enamel paint (1st quality) over a coat of red oxide zinc chrome primer by spray machine before fixing and after preparation of new steel surfaces complete all as specified and shown on drawing. (Drawing No. FD-257/1029)

Taking out old unserviceable/damaged shutter (Left/Rigt) and Supply and fixed new shutter as per existing shape and size made out of 1mm thickness plain mild steel sheet and fixed in the same position with shelf clips, nuts & bolts etc including applying painting with two coat of Olive Green synthetic enamel paint (1st quality) over a coat of red oxide zinc chrome primer by spray machine before fixing and after preparation of new steel surfaces complete all as specified and shown on drawing. (Drawing No. FD-257/1029)

Repair of Almirah steel large with shelves as appended below : Material and labour for taking out loose leg (right/left) from its position and re-fixing the same in existing position with necessary run welding of Almirah large complete all as directed. (Note : Thickness of metal to be welded shall not exceed 2mm) ( Drawing No. FD-67(M)/FD-1031)

Taking down existing unserviceable botton leg (left/right) from its position and supply and fixed new bottom leg of size 450 mm x 80 mm x 100 mm made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing. ( Drawing No. FD-67(M)/FD-1031)

Material and labour for running welding in repairs to broken/damaged sides (left/right), back and top of almirah steel large complete all as directed. (Note : Thickness of materials to be welded not exceeding 2mm in thickness and length of each welding exceeding 9mm but not exceeding 20mm in length) ( Drawing No. FD-67(M)/FD-1031)

Material and labour for repair of existing loose hinges by spot welding and make it functional by providing new steel pin including greasing etc required for smooth function complete all as directed. ( Drawing No. FD-67(M)/FD-1031)

Taking out unserviceable damaged lock from its position of almirah (large steel) and Supply and fixed new 6 lever steel lock as per existing shape and size as approved with keys in duplicate complete all as specified. Make :Link/Godrej/Standard/Aligarh ( Drawing No. FD-67(M)/FD-1031)

Taking out old and removing old unserviceable handle from Almirah steel large and Supply and fixed steel chromium plated handle 125mm long of existing shape and size complete all as specified and as directed and shown on drg.(Make :- Mowjee or Classic) ( Drawing No. FD-67(M)/FD-1031)

Taking down existing unserviceable door shutter by cutting area not exc.100 Sqcm squre/rectangle from its position and supply and fixed new door shutter made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing. ( Drawing No. FD-67(M)/FD-1031)

Taking down existing unserviceable bottom shelve from its position and supply and fixed new shelve made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing. ( Drawing No. FD-67(M)/FD-1031)

Taking down existing unserviceable intermediate shelve from its position and supply and fixed new intermadiate shelve made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing. ( Drawing No. FD-67(M)/FD-1031)

Taking down existing unserviceable door shutter from its position and supply and fixed new door shutter (Left/ Right) out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing. ( Drawing No. FD-67(M)/FD-1031)

Repair of Almirah steel Medium with shelves as appended below : Material and labour for taking out loose leg (right/left) from its position and re-fixing the same in existing position with necessary run welding of Almirah large complete all as directed. (Note : Thickness of metal to be welded shall not exceed 2mm) ( Drawing No. FD-67(M)/FD-1032)

Taking down existing unserviceable botton leg (left/right) from its position and supply and fixed new bottom leg of size 450 mm x 80 mm x 100 mm made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing. ( Drawing No. FD-67(M)/FD-1032)

Taking out loose shelf from its position of Almirah medium steel and re-fixing the same rigidly after minor repairs by providing new clips, nuts & bolts of existing size as required complete all as directed. ( Drawing No. FD-67(M)/FD-1032)

Material and labour for running welding in repairs to broken/damaged sides (left/right), back and top of almirah steel medium complete all as directed. (Note : Thickness of materials to be welded not exceeding 2mm in thickness and length of each welding exceeding 9mm but not exceeding 20mm in length) ( Drawing No. FD-67(M)/FD-1032).

Material and labour for repair of existing loose hinges by spot welding and make it functional by providing new steel pin including greasing etc required for smooth function complete all as directed. ( Drawing No. FD-67(M)/FD-1032)

Taking out unserviceable damaged lock from its position of almirah (medium steel) and Supply and fixed new 6 lever steel lock as per existing shape and size as approved with keys in duplicate complete all as specified. Make :Link/Godrej/Standard/Aligarh ( Drawing No. FD-67(M)/FD-1032)

Taking out old and removing old unserviceable handle from Almirah steel medium and Supply and fixed steel chromium plated handle 125mm long of existing shape and size complete all as specified and as directed and shown on drg.(Make :- Mowjee or Classic) ( Drawing No. FD-67(M)/FD-1032)

Taking out and removing of old broken/damaged steel of door shutter with necessary cutting in square/rectangle in shape and Supply and fixed new MS sheet as per existing size and shape not exceeding 100 Sq cm each made out of 1 mm thickness plain mild steel sheet fixed by run welding of required length including applying two coat of synthetic enamel paint (1st grade quality) over a coat of red oxide zinc chrome primer by spray machine all complete as specified and as directed. ( Drawing No. FD-67(M)/FD-1032)

Taking down existing unserviceable bottom shelve from its position and supply and fixed new shelve made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing. ( Drawing No. FD-67(M)/FD-1032)

Taking down existing unserviceable intermediate shelve from its position and supply and fixed new intermadiate shelve made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing. ( Drawing No. FD-67(M)/FD-1032)

Taking down existing unserviceable door shutter from its position and supply and fixed new door shutter made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing. ( Drawing No. FD-67(M)/FD-1032)

Repairs to Rack adjustable 6 tier steel for the following Material and labour for spot welding in repairs not exc 5cm in length of broken steel angle and corner brackets of rack steel complete all as specified and as shown in drawing. (Drawing No. FD- 1039). (Note : Material to be weled not to exceeding 2.00mm in thickness)

Material and labour for spot welding in repairs not exc 5cm in length of broken steel shelves rack steel complete all as specified and as shown in drawing. (Drawing No. FD- 1039). (Note : Material to be weled not to exceeding 2.00mm in thickness)

Taking out old unserviceable wooden seat plank from Form with back and Supply and fixed new seat plank made out of 25mm thick well seasoned first class hard wood 'Teak Wood 'timber as per existing shape and sizes with 09 Nos GI nuts, bolts and washers including preparation of wooden surfaces and applying French polish to achive high glossy finish over wood filler to exposed surfaces of timber complete all as specified and as shown on drawing. (Drawing No. FD-78(M)/ 77 (M)

Taking out old unserviceable wooden back plank from Form with back and Supply and fixed new seat plank made out of 19mm thick well seasoned first class hard wood 'Teak Wood 'timber as per existing shape and sizes with 04 Nos GI nuts, bolts and washers including preparation of wooden surfaces and applying French polish to achive high glossy finish over wood filler to exposed surfaces of timber complete all as specified and as shown on drawing. (Drawing No. FD-78(M)/ 77 (M)

Taking out old unserviceable seat plank from 'form without back' and refixing the same with providing 09 Nos GI nuts bolts and washer complete all as specified and as directed and shown on drawing. (Drawing No. FD-78(M)/ 77 (M)

Material and labour for spot welding in repairsin not exc 2,50 cm in length to broken demage leg/stiffner of form with back / without back complete all as directed. (Note : Material to be weled not to exceeding 2.00mm in thickness)

Removing of old PVC shoe/ Cap from various Type of Chairs such as Chair dining, Chair Writing, Chair Easy, Chair WB,Chaier CB etc.and replacing the same with new 20 mm dia and 10 mm high be screwed to bottom of legs all as specified an das directed. (Drawing No. FD- 281)

Removing dents, bends welding to broken portion rectifying all minor defects and repairs. Material and labour for preparation of steel surface (inside & outside surface) including doors shelves and legs, applying synthetic enamel paint (1st quality) over a coat of red oxide primer Zinc chrome primer by spray paint machine complete all as specified specified and shown on drawing for following:-

Tabble Steel 900 x 600 x 760 mm (Drawing No. FD- 1007 )

Tabble Steel 900 x 900 x 760 mm (Drawing No. FD- 1009 )

Tabble Dinning Ors (Drawing No. FD- 165(M) )

Teapoy verandah (Drawing No. FD- 35(M) /255 )

Chair CB Steel with arms (Drawing No. FD- 75(M) )

Chair CB Steel without arms (Drawing No. FD- 75(M) )

Chair Verandah (Drawing No. FD- MAP/-II/ 06 )

Almirah Large Steel (Drawing No. FD-67(M)/ 1031)

Almirah Medium Steel (Drawing No. FD-67(M)/ 1032 )

Rack Adjestable 6 tier steel (Drawing No. FD-1039)

Form with back steel (Drawing No. FD- 78(M)

Locker bed side steel. (Drawing No. FD- 257/ 1029)

M/S S.K. CONSTRUCTION

M/S S.K.DAS

samrat saw mill and joinery workshop

L. B. SHARMA