Providing Lane Marking, SS Signages and speed breakers for Ahoka Theatre road in 6th division of RMC.

Supplying of hot applied Thermoplastic road marking compound, 2.5mm thick including reflectorising glass beads @ 250gms with Reflectorising Glass Beads on Bituminous Surface at 250 gms per sqm area, thickness of 2.5mm is exclusive of surface applied glass bead as per IRC: 35, the material should be of BERGER Company/ BERGER Equivalent/Equivalent brand and must comply with the following: a) White index for the product should be in the range of 60-70 when measured against standard reference. The applied panel 7/8 number must be submitted for checking up the white index in the department lab. In case the department approves the white index of any vendor, the department engineer may carryout random checking of the applied products at site against the approved panel. In case of any major deviation, beyond acceptance limit, department reserve the right to cancel or reject the total supplied consignment of the said material and will compell the vendor has to replace the full consignment by the desired material as per approved panel at his own cost and additional demurrages may be claimed due to loss of man days (as per the rules of the department). b) Luminance factor of the material should be in the range of 80-85% at 45 degree centigrade as per AASTHOM 249. c) Crack resistance: The applied panel cured for 7 days under ambient condition and then should be tested as per BS3262, Part-1, 1989 and should pass at the range of 'O' degree centigrade to '-10' degree centigrade D) Adhesion: Strong E) Softening point: 102 degree centigrade F) Dried film finish: Smooth and uniform G) Night Vision: High as directed by the Engineer-in-Charge and confirming to IS: 164-1961 (1st revision reaffirmed in 1986) and clause conforming to IRC 35-1997

Supplying & Fixing of Twin Moulded Shanks Raised Pavement Markers made of polycarbonate and ABS moulded body and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face and shall support a load of 16000 kg tested in accordance to ASTM D 4280 Type H and complying to Specifications of Category A of MORTH Circular No RW/NH/33023/10-97-DO III Dt 11.06.1997. The height, width and length shall not exceed 50 mm, 100 mm and 100 mm and with minimum reflective area of 13 Sqcm on each side and the slope to the base shall be 35+/-5 degree. The strength of detachment of the integrated cylindrical shanks, (of diameter not less than 19+/-2 mm and height not less than 30+/-2 mm) from the body is to be a minimum value of 700 Kgs. Fixing will be by drilling holes on the road for the twin shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer's recommendation and complete as directed by the engineer.

Providing and fixing of Rubber speed Breaker having approximate weight 24-25kg per mtr Material: shall be manufactured using high-strength, durable rubber capable of withstanding heavy vehicular loads and adverse weather conditions. Dimensions: 500mmx250mmx75mm to ensure effective speed control. Color: The surface must be coated with yellow and black stripes, using UV- resistant paint or material to maintain visibility in all lighting and weather conditions. 3 The speed breakers should include a modular interlocking design for securel installation and easy removal or replacement. Installation: Anchored firmly to the road surface using heavy-duty fasteners, epoxy adhesive, ensuring stability and longevity. Load Bearing: Designed to withstand dynamic loads of up to 50 tons, suitable for both light and heavy vehicles. Certification: The product must comply with relevant traffic safety standards and ISO certifications for quality assurance. speed breaker to be fixed to the road with the help of and required complete as directed by the engineer Incharge

Manufacture, supply, delivery and erection of Stainless Steel Retro Reflective Pedestrian Crossing Signage Board of size 600 mm x 750 mm, fixed at a height of not less than 2100 mm from finished ground level to the bottom of the sign board, comprising frame fabricated from SS 304 grade square hollow sections of size 25 mm x 25 mm x 1.5 mm thick and supported on SS 304 grade square hollow section vertical post of size 75 mm x 75 mm × 2.0 mm thick, conforming to relevant IS specifications, with the post extending 2100 mm above ground level and embedded 600 mm below ground level. The sign panel shall consist of 4 mm thick Aluminium Composite Panel (ACP) of approved make such as Aludecor, Alstone or AluKobond or equivalent, having minimum 0.5 mm aluminium skin on both sides of polyethylene core, securely fixed to the stainless steel frame using stainless steel rivets, bolts, nuts and washers. The ACP panel shall be provided with Type XI High Intensity Prismatic Retro Reflective Sheeting of approved make such as 3M, Avery Dennison or Orafol or equivalent conforming to ASTM D4956 and IRC:67 latest revision, displaying symbols, bilingual messages in English and Telugu, speed restriction marking, RMC logo and other approved graphics as directed by the Engineer-in-Charge. The item shall include fabrication, cutting, welding using stainless steel electrodes, grinding, polishing, finishing, fixing of ACP sheet, application of reflective sheeting, excavation for foundation, fixing the post in PCC 1:2:4 concrete foundation, forming concrete pedestal above ground level, curing,

Supplying of hot applied Thermoplastic road marking compound, 2.5mm thick including reflectorising glass beads @ 250gms with Reflectorising Glass Beads on Bituminous Surface at 250 gms per sqm area, thickness of 2.5mm is exclusive of surface applied glass bead as per IRC: 35, the material should be of BERGER Company/ BERGER Equivalent/Equivalent brand and must comply with the following: a) White index for the product should be in the range of 60-70 when measured against standard reference. The applied panel 7/8 number must be submitted for checking up the white index in the department lab. In case the department approves the white index of any vendor, the department engineer may carryout random checking of the applied products at site against the approved panel. In case of any major deviation, beyond acceptance limit, department reserve the right to cancel or reject the total supplied consignment of the said material and will compell the vendor has to replace the full consignment by the desired material as per approved panel at his own cost and additional demurrages may be claimed due to loss of man days (as per the rules of the department). b) Luminance factor of the material should be in the range of 80-85% at 45 degree centigrade as per AASTHOM 249. c) Crack resistance: The applied panel cured for 7 days under ambient condition and then should be tested as per BS3262, Part-1, 1989 and should pass at the range of 'O' degree centigrade to '-10' degree centigrade D) Adhesion: Strong E) Softening point: 102 degree centigrade F) Dried film finish: Smooth and uniform G) Night Vision: High as directed by the Engineer-in-Charge and confirming to IS: 164-1961 (1st revision reaffirmed in 1986) and clause conforming to IRC 35-1997

Supplying & Fixing of Twin Moulded Shanks Raised Pavement Markers made of polycarbonate and ABS moulded body and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face and shall support a load of 16000 kg tested in accordance to ASTM D 4280 Type H and complying to Specifications of Category A of MORTH Circular No RW/NH/33023/10-97-DO III Dt 11.06.1997. The height, width and length shall not exceed 50 mm, 100 mm and 100 mm and with minimum reflective area of 13 Sqcm on each side and the slope to the base shall be 35+/-5 degree. The strength of detachment of the integrated cylindrical shanks, (of diameter not less than 19+/-2 mm and height not less than 30+/-2 mm) from the body is to be a minimum value of 700 Kgs. Fixing will be by drilling holes on the road for the twin shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer's recommendation and complete as directed by the engineer.

Providing and fixing of Rubber speed Breaker having approximate weight 24-25kg per mtr Material: shall be manufactured using high-strength, durable rubber capable of withstanding heavy vehicular loads and adverse weather conditions. Dimensions: 500mmx250mmx75mm to ensure effective speed control. Color: The surface must be coated with yellow and black stripes, using UV- resistant paint or material to maintain visibility in all lighting and weather conditions. 3 The speed breakers should include a modular interlocking design for securel installation and easy removal or replacement. Installation: Anchored firmly to the road surface using heavy-duty fasteners, epoxy adhesive, ensuring stability and longevity. Load Bearing: Designed to withstand dynamic loads of up to 50 tons, suitable for both light and heavy vehicles. Certification: The product must comply with relevant traffic safety standards and ISO certifications for quality assurance. speed breaker to be fixed to the road with the help of and required complete as directed by the engineer Incharge

Manufacture, supply, delivery and erection of Stainless Steel Retro Reflective Pedestrian Crossing Signage Board of size 600 mm x 750 mm, fixed at a height of not less than 2100 mm from finished ground level to the bottom of the sign board, comprising frame fabricated from SS 304 grade square hollow sections of size 25 mm x 25 mm x 1.5 mm thick and supported on SS 304 grade square hollow section vertical post of size 75 mm x 75 mm × 2.0 mm thick, conforming to relevant IS specifications, with the post extending 2100 mm above ground level and embedded 600 mm below ground level. The sign panel shall consist of 4 mm thick Aluminium Composite Panel (ACP) of approved make such as Aludecor, Alstone or AluKobond or equivalent, having minimum 0.5 mm aluminium skin on both sides of polyethylene core, securely fixed to the stainless steel frame using stainless steel rivets, bolts, nuts and washers. The ACP panel shall be provided with Type XI High Intensity Prismatic Retro Reflective Sheeting of approved make such as 3M, Avery Dennison or Orafol or equivalent conforming to ASTM D4956 and IRC:67 latest revision, displaying symbols, bilingual messages in English and Telugu, speed restriction marking, RMC logo and other approved graphics as directed by the Engineer-in-Charge. The item shall include fabrication, cutting, welding using stainless steel electrodes, grinding, polishing, finishing, fixing of ACP sheet, application of reflective sheeting, excavation for foundation, fixing the post in PCC 1:2:4 concrete foundation, forming concrete pedestal above ground level, curing,

Details of Maximum amount reimbursable to the Contractor.

1) Provision for GST @18%

2) Provision for NAC @ 0.10%