Development of Stream Draining through the Trout Reraing Unit Pahalgam and Destilation chamber with Inlet Channel at Aqua Park Pahalgam along with allied works

Development of Stream draining through the Trout Rearing unit Pahalgam and Desilation Chamber with inlet Channel at Aqua Park Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed: All kinds of soil : 1 meter from cutting edge

Providing and laying of hand packed stone Solling nallah/Quarry) incl. all carriages

Providing and laying in position cement concrete of specified grade 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) including curing but excluding the cost of centring and shuttering. All work upto plinth level with:

Centering and shuttering including strutting, propping etc. and removal of form for: Foundations, footings, bases of columns etc. for mass concrete.

Providing and laying in position cement concrete of specified grade 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including curing but excluding the cost of centring and shuttering. All work upto plinth level with:

12mm Cement plaster of mix: 1 : 4 ( 1 cement : 4 fine sand)

Carriage of Material by way of Mechnical Transport to the site of work for an average lead of 55kms a) Stone Aggregate/Sand

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting , hoisting , fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Silt clearance from canals. Inclusive of initial lead and lift ( 50m & 1.5m respectively )including disposal of silt from working site to the dumping site of work avg. Lead 200 mtrs.

Part-B) Repair/Renovation of Fisheries Hut/Guest House at Pahalgam Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed: All kinds of soil : 1 meter from cutting edge

Providing and laying of hand packed stone Solling nallah/Quarry) incl. all carriages

Providing and laying in position cement concrete of specified grade 1:3 :6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) including curing but excluding the cost of centring and shuttering. All work upto plinth level with:

Centering and shuttering including strutting, propping etc. and removal of form for: Foundations, footings, bases of columns etc. for mass concrete.

Kota stone slab flooring 25 mm thick over 20mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing, polishing and curing complete with base of cement mortar 1:4 (1 cement

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, panelling and dash fasteners to be paid for separately.) Powder coated aluminum (minimum thickness of powder coated 50 microns)

Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board (conforming to IS: 12823 Grade-I type-II) in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in- charge. Pre-laminated particle board with decorative lamination on both sides

Dismantling wood work in frames, trusses, purlins and rafters upto 10 meters span and 5 meters height including stacking the material within 50 meters lead sectional area 40 sqcm. and above.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners First class deodar wood

Fixing and erection of wooden ornamental baluster 6" dia to dtairs incl. Chamfered ornamental bottom and top (150*75mm) rail using deodar Wood with polishing complete job

Construction of Wardrobes using BWR 19mm ply board (ply toply) for frames, shutters. The job shall include fixing of denmica of approved shade/ texture on all exposed surfaces, inner linnings prefebly white (mica) hardware fittings like hings,handles, tower bolts, locks, hanger rail etc as per reqirement of architectural drawings or as directed by the Engineer in charege ( Complete Job 600mm deep)

P/F of 06 door storage cabnet made of Engineered wood self assembled with dimensions (180*30*56mm) with the accessories included.Design to be approved by Engineer incharege( Speciality panels or equilent)

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. (Decorative ply wood both side decorative veneer (type 1) conforming to IS 1328 BWR type)

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 510x1040mm bowl depth 250mm

Providing and fixing 15 mm nominal bore of standard back type C.P. brass close hole basin mixer pillar tap of approved quality and make, weighing not less than 1.970 kg.

P/F Of Exahaust Pipe for Chimmney

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete. 150x10 mm

Providing and fixing bright finished brass door latch with necessary screws etc. 250x16x5 mm

Providing and fixing bright finished brass handles with screws etc. complete :125 mm

Providing and fixing bright finished brass handles with screws etc. complete :100 mm

Providing corrugated G. S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface)excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

P/F of Crewel Curtains of superior Quality along with lining. Complete job (8' X 4') ( Design and quality to be approved by the Eic )

P/F of dwell Stainless Stain Curtain Rods 10 Feet along with all Accessories ( Design and quality to be approved by the Eic )

Carriage of Material by way of Mechnical Transport to the site of work for an average lead of 55kms a) Stone Aggregate/Sand