A and A to Campus Lighting work in at Vigilance Building and Lokayukt Building Gandhinagar. (Third Attempt)

BILL OF QUANTITIES(%TENDER)

Name of A&A to Campus Lighting work in at Vigillance Building & Lokayukt Building, Gandhinagar. (Third Attempt)

Item No Description of item(with brief specification and reference to book of specifications) Qty Unit Amount

Supplying and erecting Flexible PVC insulated multi strand multi core 1.1 kv grade ISI marked

1 copper wires of following size to be erected as directed. (e) 1.50 Sq.mm 3 core round PVC 25 Mtr 46.46

Replacing old & u/s by Supplying and erecting LED street light / Flood light fittings with High power

White LEDs wattage of 3 Watt and above assembled on single MCPCB, efficiency more than

lm/w and corrosion free High pressure die cast aluminum housing with smooth finish powder coated

and heat sink extruded aluminium with diffuser and Polycarbonate optics/ lenses, with toughened

glass with company mark/name engraved or embossed 160 to 270 V,Power Factor more than

2 0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45, Luminaire efficacy> 100 3 Nos 3345.12

lumens/watt . LED driver efficiency > 85 %.( fittings required LM-79 & LM-80 certificates)(NOTE:

Below description have shown ranges of Wattage capacity of LED fittings.The Engineer incharge

may select any wattage capacity between the ranges shown.) (A) Street Light (IP-65), Surge

protection -4KV integral and ,Light must have 440VAC line supply with over-voltage protection. (i)

above 45 to 48 watts Cat-lll (As per reruirement)

(B) Flood Light (IP-65), Surge protection -4KV integral and ,Light must have 440VAC line supply

with over-voltage protection. (iv) above 90 to 120 watts Cat-lll

Providing and erecting Miniature circuit breaker single pole 0.5A to 2A system and having breaking

capacity 10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI Mark Cat.III

Replacing old & u/s by Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C

4 Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following 2 Nos 595.90

capacity (a) 6 to 32 Amp. Cat.III

5 Sheets steel powder coated enclosure suitable for incorporating One/Two nos. MCB. 1 Nos 176.75

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted

fitted with busbar, neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 &

6 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of 4 Nos 355.52

MCB to be used) suitable for (A) single phase incoming and horizontal single phase outgoing (a)

single door (IP-30) (i)4 way

Providing and erecting Approved make RCCBs conforming to IS: 12640 and having sensitivity of

mA and Short Circuit withstand capacity of 10 KA and suitable for operation on 3 phase and neutral

7 415V,50Hz. having characteristic of quick action & tripping with all advance feature & do not 2 Nos 2569.44

incorporate any electronic component for following Max. rating erected as directed. (i) 25 Amps.FP

8 Providing and erecting HOT deep Galvanised iron strip wire 8 to 16 SWG. 1 Kg 77.77

Providing and erecting Pipe type earthing having 150 cms.long and 2.5 cms. dia. galvanised iron

9 pipe with coupling and buch buried in specially prepared earth pit complete with necessary 8 SWG 2 Nos 368.65

10 For using salt and charcoal / coke as required for pipe type earthing. 2 Nos 171.70

Replacing/Addition old, broken & u/s by Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured

11 cable multistrand / Solid Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps 195 Mtr 117.16

or in existing trench / pipe of following size of cables (A) 4 core 4 Sq. mm (As per reruirement)

Making trench in soft soil of suitable width of 90 cm deep for laying cable or locating the fault all

over the run and back filling the same and making the surface as normal ground.

Making trench in Hard Murrum / Tar Road of suitable width of 90 cm or required depth for laying

13 any size of cable or locating the fault all over the run and back filling the same and making the 90 Mtr 432.28

surface as normal ground. (B) If additional machinery like hammer driller or JCB use [Add]

Drilling the road without breaking the road surface (Asphalt) for laying of cable for feeding power

supply by making up to following size of holes at both ends complete. (A) Up to 100 mm bore dia

Providing & laying approved make Double walled corrugated pipes (DWC) of

polyethylene(conforming to IS 14930 II )with necessary connecting accessories of same material at

required depth in existing trench for laying of cable. below ground / road surface for enclosing

cable (A)50 mm outer dia (As per reruirement)

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated

16 armoured cable complete with out going tails, insulating tape etc for following size of cables. (A) 2 to 6 Nos 33.33

4 core 2.5 / 4 Sq. mm

BILL OF QUANTITIES(%TENDER)

Item No Description of item(with brief specification and reference to book of specifications) Qty Unit Amount

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly

17 crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut 24 Nos 6.06

bolts in an approved manner.(A) 1.5/ 2.5/4/6 Sq.mm.

Supplying and erecting approved make Octagonal pole made from HR sheet steel. The pole should

be made as per IS. and shall be coated with hot dip galvanizing as per IS 2629/2633/4759, suitable

suspend local wind speed with integral Junction box consist of terminal plate of min 6mm Hylam

sheet, standard profile 35mmX7.5mm Din-Rail for MCB Mounting, stud type terminal and

arrangement for cable termination to be erected With Suitable foundation (Included) as per details

given by manufacturer considering site requirement. (B) 4 Mtr. Long 70 mm Top X 130 mm bottom

dia, 3 mm thickness with 200mmX200mmX12mm base plate, 4-M16 Bolts and 450mm long with

necessary G.I. J Bolts .Approx weight 37 kg (As per reruirement)

Supplying and erecting Street light pole bracket comprising main B Class GI pipe of 4.2 cm/require

outside dia. complete with suitable B Class G.I. sleeve tubing of approx. 45cms.length and suitable

for 76.5mm/80mm/require size of pole top having nuts and bolts for fixing the brackets and having

19 spread of 0.5 mtr. Length with 110 deg.with vertical plane and suitable welded stiffener reducer and 3 Nos 491.87

nipple with check nut complete painted with one coat.of Red oxide / PU base primer and two coats

of Aluminium / PU paint. paint with following nos of arms. [A] Single Arm bracket 0.5 Mtr (As per

Supplying & erecting approved make Digital time switch having lithium cell 6 years operative and

operate battery backup 1 channel day clock with 14 memory programme, suitable to operate on

240V + 5%, 16A with, floating contacts Minimum switching setup time 1 minimum & LCD display.

Also comprised permanent ON/OFF switching. Programming switches & housed in fire proof

thermoplastic enclosure & transparent cover erected as required with necessary connection erected

Supplying & erecting power contactor, AC3 duty for time switch complete erected as per direction

Cat III (C) 4 pole 440V 16 Amp..

Two lakh ninety-six thousand and thirty-two point zero one

I/ We am/are willing to carry out the work at_________% above / below percent (should be written in figure & words) of the estimated mentioned above. Amount of my /

our tender works out as under.

Estimated amount put to Estimated amount put to

(a) I/we hereby declare that we have visited the site and fully exquisite myself/ourselves with the Local situation regarding materials labour and other factors pertaining

to work before submitting Tender.

(b) I/we hereby declare that we have carefully studies the conditions of contracts. Detailed Specification and other tender document of this work and agree to execute

the same accordingly.

1 If required and found necessary material to be used for this work and brought at site will have to sent to Govt.approved laboratory. The qualified agency/

manufacturer of Particular product under testing will have to pay/ bear necessary charges.

2 All works shall be carried out as per public works Department hand book and other Specification.

3 Rates are inclusive of 1% Labour cess in tender amount so 1% of total amount of bill will be deducted from the bill.

3 Rates are inclusive of 1% Labour cess in tender amount so 1% of total amount of bill will be deducted from the bill.

4 The material to be used in this work must be as per instruction by under liason of Engg. In charge.The agency will have to agree to carried out the work as

per brand/make demand of concern deptt.

5 Contractor must have registration in E-2 & above class registered under elect. (R & B) division.

Sign of Dy. Exe. Engineer Exe. Engineer

Contractor Sachivalay Complex Elect. Sub-Div.No.-2 Sachivalay Complex Elect. Div

R. & B. Deptt. Gandhinagar R. & B. Deptt. Gandhinagar