COMPLETION OF INCOMPLETE WORKS FOR PROVN OF CULVERT WITH HUME PIPE AND SPECIAL REPAIR TO BUILDING NO T-31 AT GBS CAMP KOTDWARA UNDER GE LANSDOWNE

Amount

Excavation in trenches in soft / disintegrated rock not exceeding 1.5 mtr deep and not exceeding 1.50 mtr wide and getting out complete all as specified and directed.

Returning, filling in the rock / soil particles in layers not exceeding 25 cm thick each layer by spreading, levelling, watering and well ramming complete all as specified and directed.

Removal of surplus rock / soil particles to a distance not exceeding 50 mtr away and at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed.

Dismantling un-framed timber scantlings 40 Sqcm in section or over fixed in any position complete all as specified and directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc. 15 cm thick (Below and above ground level) and dispoing the rubbish off the site of work complete all as specified and directed.

Demolition of RCC of any description and in any position not otherwise specifically provided for and dispoing the rubbish off the site of work complete all as specified and directed.

Taking down Chowkats or frames (without taking off shutters from the frames) from the opening of size exc 1.5 Sqm but not exc 4 Sqm each complete all as specified and directed.

M & L for PCC 1:4:8 type D-2 (using 40 mm graded stone aggregates) as in foundation / filling, sub base and mass concrete complete all as specified and directed

M & L for PCC 1:3:6 type C-2 (using 40 mm graded stone aggregates) as in surface channels and drain complete all as specified and directed

M & L for PCC 1:2:4 Nominal Mix type B-0 (using 12.50 mm grade stone aggregates) as in coping, benching, cills, lintel band, filling around hold fasts, fitting in chowkats etc including necessary form work weathering, slightly rounded or chamefered angles and throating complete all as specified and directed.

M & L for PCC 1:2:4 type B-2 (using 40 mm graded stone aggregates) as in surface channels, drain beds and the similar works complete all as specified and directed

M & L for extra for forming fair finish to drain or channel 45 cm girth in cement concrete using extra cement including necessary form work complete all as specified and directed.

M & L for Precast cement concrete 1:1.5:3 type A-1 (using 20 mm graded stone aggregates) as in slabs / lintels etc set in CM 1:6 complete all as specified and directed.

M & L for RCC 1:2:4 type B-1 (using 20 mm graded stone aggregates) as in slabs supported on walls, beams and columns and in floor landings, roof landings , shelves and the like complete all as specified and directed

Use and waste of form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and the similar works not exceeding 200 mm thick (Horizontal or slopping) complete all as specified and directed.

M & L for brick work with sub class 'B' bricks (old size) straight or curved on plan exceeding 6 mtr mean radius built in cement mortar 1:6 complete all as specified and directed.

S & F RCC pipe 600 mm bore, class NP-2 laid and jointed with collars and cement mortar complete all as specified and directed.

S & F mild steel TMT bars 10 mm dia and over cut to length, bent to shape required including cranking, binding spirally for hooping for columns, hooking ends and binding with and including mild steel binding wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

S & F pre-painted galvalume aluminium zinc coating AZ-150 GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed.

S & F exposed metal frame ceiling with 8 mm thick calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600 mm x 600 mm grid complete all as specified & directed. Npte :- The frame work for ceiling shall be measured and paid for separately under appropriate item of Sch 'A'.

M & L for aluminium anodised snap grid frame work (size of grid 605 x 605 mm) for false ceiling including GI hangers of 6 mm dia (upto 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size 60 mm long and expansion hold fasteners 12.5 mm dia 40 mm long complete all as specified and directed.

S & F 6 mm thick plywood grade BWR type BB, fixed to frame work to ceiling with nails complete all as specified and directed.

S & F mild steel framed work such as grills, gratings etc with ends of bars shouldered and / or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, hold fasts, frame work of water tanks and the similar works conforming to Fe-290.Gde-E-165 complete all as specified and directed.

S & F second class hard wood (Not less than Hollock wood) as in scantlings, wrought and fixed, in framed work complete all as specified and directed.

S & F second class hard wood (Not less than Hollock wood) as in plain fillets, clean sawn, square, rectngular in section exceeding 6 sqcm but not exceeding 13 sqcm and fixed with nails complete all as specified and directed.

S & F second class hard wood (Not less than Hollock wood) as in plain fillets, clean sawn, square, rectngular in section exceeding 13 sqcm but not exceeding 25 sqcm and fixed with nails complete all as specified and directed.

M & L for Plain, solid, straight, Chowkhat and frame wrought, framed, rebated on the solid rounded or chamfered put together with glue pinned at joints, supplied and fixed IInd class Hard Wood ( Not less than Hollock wood) complete all as specified and directed.

S & F 40 mm thick factory made pannelled shutter of second class hard wood ( Not less than Hollock wood) Plain, framed, panelled (two panel) with lock rail and panel of 9 mm BWP commercial ply on both faces, the size of rail and stile as per IS 1003(part-1) klin seasoned and chemically pressure treated complete all as specified and directed.

S & F Glazed and skelton shutters 35 mm thick of IInd class hard wood ( Not less than Hollock wood), open rebeated and prepared to receive glass, guage, etc(with out sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred moulded beads on both sides for securing glass etc. sizes of members of shutters as specified in SSR Part I, Section - 8 Clause - 8.24(a) supplied and fitted to chowkat complete all as specified and directed.

S & F 19 / 20 mm thick exterior grade prelaminated particle board water proof ( Prelaminated on one side ) as in cub board shutters, lipping and necessary rabating for double shutter where required including polishing to lipping complete all as specified and directed.

S & F Solid PVC Door Frame of size 50mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing mentioned in Section 8 of SSR-II complete all as specified and directed.

S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing mentioned in Section 8 of SSR-II complete all as specified and directed.

S & F 100 mm long stainless steel butt hinges, medium weight complete all as specified and directed.

S & F 75 mm long stainless steel butt hinges, medium weight complete all as specified and directed.

S & F 200 mm long (Length of bolt) aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S & F 150 mm long (Length of bolt) aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S & F 250 mm long (Length of bolt) aluminium alloy, anodised sliding door bolts, with hasp & staple (clip type), cast or extruded sections and fixing bolts and sliding bolt of extruded sections or cast aluminium alloy and including a minimum of 6 bolts and nuts ( four on bolt plate and two on staple plate) complete all as specified and directed.

S & F 300 mm mild steel ordinary rat tail, rod pattern springs including roller and roller plate complete all as specified and directed.

S & F 125 mm long aluminium handles, cast type, anodised complete all as specified and directed.

S & F 100 mm long aluminium handles, cast type, anodised complete all as specified and directed.

S & F 75 mm long aluminium handles, fabricated type, anodised complete all as specified and directed.

S & F 125 mm size hasp and staple safety type aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

S & F door closure of aluminium ( Extruded section) hydraulically regulated, designation No. 2, universal type, suitable for door shutter of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden / steel frames, glazed with putty or fixed with beads anf S & F 3 mm thick plain sheet glass, ordinary quality and glazing with oil putty or fixed with beads in square not exc. 0.5 Sqm in each pane complete all as specified and directed.

S & F 3 mm thick plain sheet glass, ordinary quality and glazing with oil putty or fixed with beads in square not exc. 0.5 Sqm in each pane complete all as specified and directed.

S & F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel tinned tacks complete all as specified and directed.

Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing) and removing rubbish off the premises and S & F Glazed ceramic coloured tiles as in skirting / dado of size 300 mm X 200 mm X 7 mm thick, set and jointed in neat cement slurry and pointed with white cement mixed with colour pigment to match the colour of tiles over and including 10 mm thick screed bed plaster in CM 1:4 complete all as specified and directed.

Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing) and removing rubbish off the premises and S & F Non skid ceramic coloured tiles as in flooring of size 300 mm X 300 mm X 7 mm thick, set and jointed in neat cement slurry and pointed with white cement mixed with colour pigment to match the colour of tiles over and including 15 mm thick screed bedding in CM 1:6 complete all as specified and directed.

Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing) and removing rubbish off the premises and S & F Non skid ceramic coloured tiles as in flooring of size 400 mm X 400 mm X 7 mm thick, set and jointed in neat cement slurry and pointed with white cement mixed with colour pigment to match the colour of tiles over and including 15 mm thick screed bedding in CM 1:6 complete all as specified and directed.

Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar and removing rubbish off the premises and S & F machine cut kota stone slab flooring 20-25 mm thick as in floors set and jointed in neat cement slurry and pointed with grey cement mixed with colour pigment to match the colour of slab over and including 20 mm thick screed bed layer in cement mortar 1:6 including cutting, grinding, polishing ( mirror polishing) complete all as specified and directed.

Dismantling stone slabs and tiles of any description or thickness as in skirting / dado etc laid, bedded and pointed in any mortar and removing rubbish off the premises and S & F machine cut kota stone slab flooring 20-25 mm thick as in skirting / dado / pillars / risers of step set and jointed in neat cement slurry and pointed with grey cement mixed with colour pigment to match the colour of slab over and including 10 mm thick screed bed layer in cement mortar 1:4 including cutting, grinding, polishing ( mirror polishing) complete all as specified and directed.

Dismantling stone slabs and tiles of any description or thickness as in cooking shelf, platform etc laid, bedded and pointed in any mortar and removing rubbish off the premises and S & F granite ( of any type ) machine cut 20 mm thick as in cooking platform, shelf set and jointed in neat cement slurry and pointed with white cement mixed with admixture of pigment to match the colour of granite stone over and including 20 mm thick screed bed layer in cement mortar 1:6 including cutting, grinding, polishing complete all as specified and directed.

S & F chequered cement concrete tiles 20 cm x 20 cm x 25 mm thick set, jointed and pointed in neat cement slurry as in flooring over 20 mm thick screed bedding in CM 1:6 complete all as specified and directed.

M & L for 75 mm thick PCC 1:3:6 Nominal Mix type C-2 (using 40 mm grade stone aggregates) as in plinth protection finished even and fair laid in bays complete all as specified and directed.

M & L for 100mm thick PCC 1:2:4 type B-1 (using 20 mm graded stone aggregates) finish fair and even complete all as specified and directed.

M & L for forming 12 mm thick expansion joints filled with perforated bituminous filler and top 30mm primed amd sealed with sealing compound grade `A` for 75 mm thick complete all as specified and directed.

M & L for 15 mm thick rendering on fair faces of brick masonary or concrete surfaces in CM 1:4 finished even and smooth without usnig extra cement complete all as specified and directed.

M & L for 15 mm thick rendering in CM 1:4 on fair faces of brick work finshing even and smooth without using extra cement and applying two coats of oil bound distemper over a coat of 3 mm thick Birla white wall care putty after preparation of surfaces complete all as specified and directed.

Taking down cement or cement lime plaster from brick or stone walls etc. including raking out joints, hacking for keys, scrubbing down with water etc. and dispoing the rubbish off the site of work and M & L for 15 mm thick rendering in CM 1:4 on fair faces of brick work finshing even and smooth without using extra cement and applying two coats of cement base paint after preparation of surfaces complete all as specified and directed.

M & L for applying two coats of oil bound distemper over a coat of 3mm thick Birla white wall care putty after preparation of surface complete all as specified and directed.

M & L for applying two coats of cement base paint after preparation of surface complete all as specified and directed.

Taking down cement or cement lime plaster from brick or stone walls etc. including raking out joints, hacking for keys, scrubbing down with water etc. and dispoing the rubbish off the site of work and M & L for 15 mm thick rendering in CM 1:6 on fair faces of brick work finshing even and smooth without using extra cement and applying three coats of white wash after preparation of surfaces complete all as specified and directed.

M & L for preparation of old plastered or unplastered surface on walls by complete removal of the old treatment by scrapping, burnning etc and applying two coats of oil bound distemper over a coat of 3 mm thick birla white wall care putty complete all as specified and directed.

M & L for preparation of old plastered or unplastered surface on walls by complete removal of the old treatment by scrapping, burnning etc and applying two coats of cement base paint complete all as specified and directed.

M & L for preparation of new wooden or previously untreated wooden surfaces exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M & L for preparation of old painted wooden surfaces exceeding 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M & L for preparation of new steel or previously untreated steel surfaces exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S & F in replacement 500 Ltrs capacity rotational moulded polythylene water storage tanks (Cylinderical vertical with closed top) double walled hoisted and fixed in position including PTMT float valve 15 mm bore high pressure with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed (Minimum wt -142grams) complete all as specified and directed.

Taking up or down 15 mm bore steel tubing and connections and S & F 15 mm bore galvanised steel water tubing medium grade with and including all fittings and laid in walls or floors complete all as specified and directed.

S & F in replacement 15 mm bore bib taps, fancy type Chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F in replacement 15 mm bore stop valves / angle valves, cast copper alloy, chromium plated (concealed type) screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S & F in replacement sink with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plug, washers, waste coupling 32 mm bore PTMT and waste pipeand bedding in wall in PCC 1:2:4 type B-0 with two number cantilever brackets and connecting to union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed.

S & F in replacement 15 mm bore gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipe or for unions complete all as specified and directed.

S & F in replacement 15 mm bore pillar taps, cast copper alloy with crutch or butterfly handle, chromium plated screwed down for high pressure with lettered 'Hot' or 'Cold' with long shank, flynut, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F in replacement Vitreous China Wash hand Basin white, flat back, size 450x300 mm, waste coupling 32 mm bore of PTMT, waste pipe, chain and plug and porcelain stopper and brackets complete all as specified and directed.

S & F in replacement PVC Flushing cistern 10 lts caapcity, low level, white with inlte, valve, float, 32 mm bore flush pipe and also connect to WC and handle including Brackets complete all as specified and directed.

S & F in replacement vitreous china water closet (squatt pattern) Orissa type 580 X 440 mm long pan white with CI P or S trap front or back inlet, foot rests including provn of concrete bedding including connections to flushing cistern/pipe complete all as specified and directed.

S & F in replacement PVC connection 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S & F in replacement PVC Floor Trap 75 mm dia, with grating including jointing to waste pipe fixed with PCC 1:2:4 type B-0 including necessary cutting complete all as specified and directed

M & L for point wiring with 1.5 Sqmm PVC insulated unsheathed,stranded copper conductor FR cable single core 1100 Volts grade in and including rigid PVC conduit 20 mm or higher size medium grade in concealed manner with all PVC conduit accessories with provision of CI / pressed steel terminal switch box & white bakelite plastic laminated top sheet cover fixed with brass screws and cup washers and 1.5 Sqmm PVC insulated unsheathed stranded FR copper conductor single core 1100 Volts grade as earth wire & wire connected with main earth point for One light / fan / bell point controlled by one one way switch piano type 5 Amp complete all as specified & directed.

All as per Srl item No. 81 here-in-before but for one 3 pin 5 Amp socket outlet on the same board controlled by one, one way 5 Amps piano type complete all as specified & directed.

All as per Srl item No. 81 here-in-before but for one 3 pin 5 Amp socket outlet on the independent board controlled by one, one way 5 Amps piano type complete all as specified & directed.

All as per Srl item No. 81 here-in-before but for one power point wiring for one 15 Amp switch socket combined outlet point on Independent Board with 2.5 Sqmm PVC insulated unsheathed,stranded FR copper conductor cable single core 1100 Volts grade and 1.5 Sqmm PVC insulated unsheathed stranded FR copper single core 1100V grade as earth wire & wire connected with the main earth point.complete all as specified & directed.

S & F switch piano flush single pole one way 5 / 6 Amps complete all as specified and directed.

S & F socket outlet flush single pole 3 / 5 pin 5 / 6 Amp 230 volts complete all as specified and directed.

S & F switch socket outlet combination multipurpose 5 in 1, flush type 5 / 6 pin 15 / 16 Amp 230 volts complete all as specified and directed.

S & F ceiling rose PVC / Polycorbonate surface bakelite 65 mm x 50 mm having three terminals complete all as specified and directed.

S & F batten lamp holder PVC / Polycorbonate insulator body with back plate suitable for PVC fitting with fixed on PVC rectangular block of 10 cm x 10 cm x 5cm depth complete all as specified & directed.

S & F stepped type electronic fan regulator socket type on the existing phenolic laminated sheet complete all as specified and directed.

S & F in replacement sheet metal enclosure for MCB's DBs single pole & neutral 240 Volts AC with 200 Amp rated neutal bus bar suitable for 8 ways outgoing MCBs double door complete all as specified & directed.

S & F in replacement MCB single pole 240 Volts AC 6 to 32 Amps of 10 KA capacity complete all as specified & directed.

S & F in replacement MCB single pole & neutral 240 Volts AC 40 - 63 Amps of 10 KA capacity complete all as specified & directed.

S & F in replacement 1100 volt grade heavy duty cable PVC insulatd stranded aluminium conductor, served with inner seathing of PVC tape and overall PVC seathed in service connection suspended with insulating hangers not more than 1 metre apart including 4 mm dia suspension wire alongwith 16 sqmm twin core flat cable complete all as specified and directed.

S & F in replacement Exhaust fan, heavy duty metalic boby of 305 / 300 mm sweep 900 RPM single phase 230 volt 50 Hz electric driven including louvers and all fixing accessories and opening hole in existing wall of suitable size and fixing with PCC 1:2:4 type B-0 and connection with copper conductor PVC insulated sheathed cord of suitable size complete all as specified and directed.

S & F in replacement sub main wiring with two single core PVC insulated, unsheathed, stranded FR copper conductor cable 4 Sqmm with 2.5 Sqmm PVC insulated, unsheathed, stranded FR copper conductor cable as earth wire in and including rigid PVC conduit 20mm dia or higher, medium grade ISI marked and earth wire connected to common earth point complete all as specified & directed. Note: Two run of 4 sqmm cable, one run of 2.5 qsmm cable and one run of PVC conduit shall be measured as one unit

M & L for cutting chases, pinning in making good to facing where required and pointing in CM 1:2 to ends for concealed conduit wiring and making good, cutting of size not exceeding 10 cm in girth complete all as specified & directed.

S & F in replacement rewireable switch fuse unit with sheet metal enclosure TPN fused 63 Amp 415 volts complete all as specified & directed. Make:- Havells/L&T/HPL/Indo Asian

S & F in replacement water heater (Geyser) storage type, suitable to operate on AC 230 volts, electric deriven of capacity 25 Ltrs including PVC connection 2 number, CP angle cock 02 number complete all as specified & directed. Make :- Havells Monza DX or equivalent Make in Bajaj/Crompton/Usha

S & F in replacement Tube light fitting 1 x 28 watt 230 volts energy efficient T-5 box type epoxy powder coated CRCA sheet housing with reflector cover channel with electronic ballast, tube rod of 28 Watt, bipin holders, connector block etc complete with all accessories internally prewired and including connected with twin core twisted flexible copper wire conductor cable of suitable size complete all as specified & directed.Make Havell's / Bajaj / Phillips / Surya Roshni Ltd / Phillips / Crompton Greaves

S&F in replacement LED street light new generation energy savings, environmental, long life versatile pressure die-cast aluminium IP-66 read way luminire with high power LED light source 24W and electric dirver complete with accessories internally prewired copper conductor cable suitable size complete all as specified & directed. Make - Havells Cat part No. LHETAXU7UN6W024 M or equivalent approved by Engr-in-Charge.

M & L in replacement for earthing complete with galvanized earth plate electrode 600x 600 x 6mm thick buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge of the plate not less than 1.5mtr below ground level connected to galvenised earth lead wire of 4 mm dia by means of nuts, bolts, washes of galvanized iron or steel all as shown in electrical plate No 5 and testing on completion including adequate charcoal dust comman salt necessary excavation & earth work, PCC 1:3:6 type C-1 pit with precast RCC cover slab 40 mm thick in PCC 1:2:4 type B-0 reinforced with 6 mm dia MS round bars @ 100 mm c / c both ways with funnel wire mesh and 20 mm dia GI pipe medium grade as watering pipe including connecting to earthing test point complete all as specified and directed. Note: - An amount of Credit for Rs.21,991.00 for the retrieved materials is mentioned in the Schedule of Credit of the tender documents in Pdf form which will be deducted while acceptance of tender offline.

OM SAI ASSOCIATES AND DEVELOPERS

RAMAPATI ENGINEERING SERVICES