GE863/EWS-T-55 OF 2020-21

Amount

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing, serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for Non-skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but n.exc 0.18 sqm, in floors etc. set over and including 15 mm thick screed bed in cement mortar 1:6 and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L Glazed ceramic coloured tiles (300x200mm) x 7 mm thick on vertical surfaces etc, set and jointed in neat cement slurry and pointed in white cement to match such skriting /dado and risers to steps etc laid over and including bedding layer of 10mm thick in cement mortar 1:4 complete all as specified and directed.

M&L 25mm thick cement concrete type B-0, 1:2:4 (using 12.5mm graded stone agg ) as in sub flooring complete all as specified and directed.

M&L Chequered cement concrete tiles 30cm x 30 cm x 25mm thick including screed bedding 15mm thick in cement mortar 1:6, set jointed and pointed in neat cement slurry in floors with white cement and pigments complete all as specified and directed.

M&L PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in bed plates, coping, kerbs, water trough and like incl. rounded or chamfered on edges complete all as specified and directed.

M&L 50mm thick PCC 1:3:6 Type C-1 using 20mm crushed stone aggregate as in plinth protection and finished even and smooth without using extra cement complete all as specified and directed.

Taking down cement or cement lime plaster any description on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L 15mm thick rendering on brick work or concrete surfaces in cement mortar 1:6 finished even and fair complete all as specified and directed.

M & L for rendering 10mm thick on fair faces of brick or concrete surfaces in cement mortar 1:4 using WPC 3% by weight of cement and finished surface even and smooth (without using extra cement) complete all as specified and directed. NOTE: - water proofing compound shall be measured and paid separately as 'supply only'.

Supply only integral water proofing compound complete all as specified and directed.

M & L for preparing newly plastered or previously untreated walls surfaces and applying two coats of cement base paint complete all as specified and directed.

Taking down chowkats or frames(without taking off shutters from the frame) area exc 1.5 Sqm but n.exc 4.0 Sqm each complete all as specified and directed.

Taking down shutters (of any description) area exc. 1sqm but n. exc 2.0Sqm each complete all as specified and directed.

S & F 30 mm thick flush shutter solid core construction, with block board core and plywood face panels, commercials type on both sides complete all as specified and directed.

S & F of 35 mm thick (Batten thickness) 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without shash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. and sizes of the members of shutters as specified in clause No . 8.24 (a) of MES schedule part – I (Specifications - 2009), supplied and fitted to chowkhats complete all as specified and directed.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and directed.

S&F plain sheet glass/pin headded glass of 3 mm thick in Squares not exceeding 0.50 Sqm in each pane with oil putty and clips complete all as specified and directed.

S & F Galvanized mild steel wire cloth, 0.56 mm dia of wire and average width of aperture 1.18 mm and fixed with tinned stacks, or galvanized wire staples complete all as specified and directed.

S & F Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M & L for preparation of new or previously untreated wood and wood based surface of any description not otherwise described and exc 10cm width or girth applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M & L for preparation of new or previously untreated surfaces of steel of any description, not otherwise described, over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F 150mm aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 250mm aluminium alloy anodised sliding bolts with hasp, staple and fixing clips of sheet, cast or extruded section fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed.

S & F butt hinges, 100mm medium weight, cold rolled mild steel complete all as specified and directed.

S & F 150 mm Aluminium handles, cast type, anodised of extruded section complete all as specified and directed.

Hacking out old broken glass (any thickness) , size, quality or description ) from metal frame including punching or drilling out old glazing pins complete all as specified and directed.

S&F in repair PVC valve less, syphonic action type low level flushing cistern of capacity 10 Ltrs with inlet, ball valve, float and handle and fixed to IWC on existing brackets complete all as specified and directed.

S&F in repairs chlorium plated brass shower roses with or without swivel joints 100mm size incl fixing to steel pipe complete all as specified and directed.

S&F in repairs 15 mm bore pillar taps, cast copper alloy, with chromium plated etc. complete all as specified and directed.

S&F in repair vitreous china wash basin with vitreous China Pedastal, white, flat back, size 550 x 400mm, fixed on existing brackets incl 32mm bore CP waste coupling complete all as specified and directed.

S&F in repair bib taps fancy type copper alloy chromium plated with crutch or butter fly handle screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repairs 15mm bore stop valve/angle valve cast copper alloy chromium plated fancy type screwed down, high pressure, with crutch or butter fly handles complete all as specified and directed.

S&F in repairs stop valves 20mm, cast copper alloy, screwed down, high pressure with crutch or butterfly handle etc complete all as specified and directed.

S&F in repair PVC connection of size 15mm with PTMT nuts of length 450mm complete all as specified and directed.

S&F in repairs 20mm bore Brass ball valve with polythene float and fly nut complete all as specified and directed.

S&F in repairs vitreous china wash down water closet pedestal pattern pan white with trap including connection to existing out joint pipe, flushing pipe or cistern, antisyphonage pipe, including making, etc complete including making goood to floor etc complete all as specified and directed.

S&F in repairs stainless steel sink with drainage board made out of 1.00mm thick stainless steel sheet for kitchen or laboratory, with plug, waste pipe, washers incl. cantiliver cast iron brackets, connecting union etc overall size 915mm X 460mm with bowl size 410mm X 330mm X 160mm complete all as specified and directed.

S&F in repair 75mm bore PVC (SWR) soil, waste and vent pipe, in any length , with rubber joints,fixed vertically on wall complete all as specified and directed.

S&F PVC (SWR) floor traps 75mm bore with grating and jointing to waste pipe in solvent cement complete all as specified and directed.

Demolition of precast concrete block walling masonary, built in cement mortar or cement lime mortar incl all quoins, arches, pillars, etc but excluding ashlar facing, dressed stone work and precast concrete articles complete all as specified and directed.

M&L 1:3:6 type C-1 precast cement concrete (20mm graded stone aggregate) block masonary with solid blocks exc 10 cm in width and not exc 20cm in width and setting in cement mortar 1:6 complete all as specified and directed.

M&L in repair for 20mmdia bore Low density polythylene pipes (LDPE) of pressure rating 6kgf/cm2 fixed complete on walls, ceiling or in floors etc. complete all as specified and directed.

M&L for preparation of surface including washing rubbing down and applying of two coat cement base paint to old surfaces of walls complete all as specified and directed.

M&L for washing, rubbing down and stopping of distempered surface and applying of one coat of oil bound distemper to old surfaces of walls complete all as specified and directed.

M & L for preparation of old surfaces of steel of any description , over 10 cm in width or girth not otherwise described and applying one coat of synthetic enamel paint (ordinary tint) complete all as specified and directed.

M&L for preparation of old surfaces and applying two coat of white wash on wall complete all as specified and directed

M&L for Cleaning of water storage tank of capacity 2 x 20000 litre having two compartments by following process complete all as specified and directed :-

Mechanised removal of all remaining dirty water by high capacity submersible pump set.

Removal of sludge by vacuum operated German pump.

Cleaning of walls, ceiling and bottom of tank by German made high pressure rotary jet 120 bars pressure.

Removal of all dirty particle by industrial wet vacuum cleaner leaving the tank 99.9% physically cleaned.

Sterlization of tank by Eco-Friendly biodegradable and highly effective against all pathogens.

Sterlization of tank atmosphere by industrial UV radiator leaving the tank.

M&L for Cleaning of water storage tank of capacity 80000 litre having two compartments of 40000 litre each by following process complete all as specified and directed :-

Mechanised removal of all remaining dirty water by high capacity submersible pump set.

Removal of sludge by vacuum operated German pump.

Cleaning of walls, ceiling and bottom of tank by German made high pressure rotary jet 120 bars pressure.

Removal of all dirty particle by industrial wet vacuum cleaner leaving the tank 99.9% physically cleaned.

Sterlization of tank by Eco-Friendly biodegradable and highly effective against all pathogens.

Sterlization of tank atmosphere by industrial UV radiator leaving the tank.

M&L for Cleaning of under ground / semi under ground water storage sump of capacity 1.8 M gallons by following process complete all as specified and directed :-

Mechanised removal of all remaining dirty water by high capacity submersible pump set.

Removal of sludge by vacuum operated German pump.

Cleaning of walls, ceiling and bottom of tank by German made high pressure rotary jet 120 bars pressure.

Removal of all dirty particle by industrial wet vacuum cleaner leaving the tank 99.9% physically cleaned.

Sterlization of tank by Eco-Friendly biodegradable and highly effective against all pathogens.

Sterlization of tank atmosphere by industrial UV radiator leaving the tank.

M & L for cleaning of RCC water tank (underground sump) of capacity upto 10000 litre by wire brush and chemicals to remove all algae/fungi growing on inside water tank surfaces and then white wash the tank surfaces in two coats with freshly burnt fat lime of class 'C' complete all as specified and directed.

M & L for rewinding of motor of capacity 5 HP by taking out old winding wires, cleaning slots and rewinding with PVC insulated copper wire of same size & guage as existing glass sleaves etc and replacement of thrust bearings and testing on completion complete all as specified and directed.

M & L for rewinding of motor of capacity 1 HP by taking out old winding wires, cleaning slots and rewinding with PVC insulated copper wire of same size & guage as existing glass sleaves etc and replacement of thrust bearings and testing on completion complete all as specified and directed.

Taking out/taking down old unserviceable damaged GI water tubing pipe of 150 mm size from excavated trenches or from wall/floor including removing of fittings complete all as specified and directed. Note:- Excavation and earth work shall be measured and paid separately under respective items.

Taking out/taking down old unserviceable damaged GI water tubing pipe of 100 mm size from excavated trenches or from wall/floor including removing of fittings complete all as specified and directed. Note:- Excavation and earth work shall be measured and paid separately under respective items.

Taking out/taking down old unserviceable damaged GI water tubing pipe of 80 mm size from excavated trenches or from wall/floor including removing of fittings complete all as specified and directed. Note:- Excavation and earth work shall be measured and paid separately under respective items.

Taking out/taking down old unserviceable damaged GI water tubing pipe of 50/40 mm size from excavated trenches or from wall/floor including removing of fittings complete all as specified and directed. Note:- Excavation and earth work shall be measured and paid separately under respective items.

Taking out/taking down old unserviceable damaged GI water tubing pipe of 25 mm size from excavated trenches or from wall/floor including removing of fittings complete all as specified and directed. Note:- Excavation and earth work shall be measured and paid separately under respective items.

Taking out/taking down old unserviceable damaged GI water tubing pipe of 20 mm size from excavated trenches or from wall/floor including removing of fittings complete all as specified and directed. Note:- Excavation and earth work shall be measured and paid separately under respective items.

Taking out/taking down old unserviceable damaged GI water tubing pipe of 15 mm size from excavated trenches or from wall/floor including removing of fittings complete all as specified and directed. Note:- Excavation and earth work shall be measured and paid separately under respective items.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in deep and getting in hard/dense soil for laying of cable or foundation etc. complete all as specified and directed.

Returning refiling in, including spreading, leveling watering and well raming in layers each not exceeding 25 cm thickness complete all as specified and directed.

Removing surplus soil to a distance not exceeding 50 mtr and deposting where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed.

S & Laying GI tubing medium grade of size 150 mm bore including all fitting such as bend, Tee, union, socket etcin trenches complete all as specified and directed.

S & Laying GI tubing medium grade of size 100 mm bore including all fitting such as bend, Tee, union, socket etc in trenches complete all as specified and directed.

S & Laying GI tubing medium grade of size 80 mm bore including all fitting such as bend, Tee, union, socket etc in trenches complete all as specified and directed.

S & Laying GI tubing medium grade of size 50 mm bore including all fitting such as bend, Tee, union, socket etc in trenches complete all as specified and directed.

S & Laying GI tubing medium grade of size 40 mm bore including all fitting such as bend, Tee, union, socket etc in trenches complete all as specified and directed.

S & Laying GI tubing medium grade of size 25 mm bore including all fitting such as bend, Tee, union, socket etc in trenches complete all as specified and directed.

S & Laying GI tubing medium grade of size 20 mm bore including all fitting such as bend, Tee, union, socket etc in trenches complete all as specified and directed.

S & Laying GI tubing medium grade of size 15 mm bore including all fitting such as bend, Tee, union, socket etc in trenches complete all as specified and directed.

S & F in repair Sluice Valve of size 150 mm bore class PN 1.6 GI with iron wheel head , screwed both ends for GI tubing medium grade complete all as specified and directed.

S & F in repair Sluice Valve of size 100 mm bore class PN 1.6 GI with iron wheel head , screwed both ends for GI tubing medium grade complete all as specified and directed.

S & F in repair Sluice Valve of size 80 mm bore class PN 1.6 GI with iron wheel head , screwed both ends for GI tubing medium grade complete all as specified and directed.

S & F in repair Gun-metal, globe or gate valves of size 65 mm bore with iron wheel head , screwed both ends for GI tubing medium grade complete all as specified and directed.

S & F in repair Gun-metal, globe or gate valves of size 50 mm bore with iron wheel head , screwed both ends for GI tubing medium grade complete all as specified and directed.

S & F in repair Gun-metal, globe or gate valves of size 40 mm bore with iron wheel head , screwed both ends for GI tubing medium grade complete all as specified and directed.

S & F in repair Gun-metal, globe or gate valves of size 25 mm bore with iron wheel head , screwed both ends for GI tubing medium grade complete all as specified and directed.

S & F in repair Gun-metal, globe or gate valves of size 20 mm bore with iron wheel head , screwed both ends for GI tubing medium grade complete all as specified and directed.

S & F in repair Gun-metal, globe or gate valves of size 15 mm bore with iron wheel head , screwed both ends for GI tubing medium grade complete all as specified and directed.

S & F in repair air release valves of size 100 mm bore with iron screwed both ends for GI tubing medium grade complete all as specified and directed.

S & F in repair air release valves of size 80 mm bore with iron screwed both ends for GI tubing medium grade complete all as specified and directed.

S & F in repair air release valves of size 50 mm bore with iron screwed both ends for GI tubing medium grade complete all as specified and directed.

S&F in repair GI Plug of size 80 mm complete all as specified and directed.

S&F in repair GI Plug of size 50 mm complete all as specified and directed.

S&F in repair GI Plug of size 40 mm complete all as specified and directed.

S&F in repair GI Plug of size 25 mm complete all as specified and directed.

S&F in repair GI Plug of size 20 mm complete all as specified and directed.

S&F in repair GI Nipple of size 50 mm complete all as specified and directed.

S&F in repair GI Nipple of size 40 mm complete all as specified and directed.

S&F in repair GI Nipple of size 25 mm complete all as specified and directed.

S&F in repair GI Nipple of size 20 mm complete all as specified and directed.

S&F in repair GI Socket reducer of size 40/25 mm complete all as specified and directed.

S&F in repair GI Socket reducer of size 25/20 mm complete all as specified and directed.

S&F in repair GI Socket reducer of size 20/15 mm complete all as specified and directed.

S&F in repair GI Plain Socket of size 50 mm complete all as specified and directed.

S&F in repair GI Plain Socket of size 40 mm complete all as specified and directed.

S&F in repair GI Plain Socket of size 25 mm complete all as specified and directed.

S&F in repair GI Plain Socket of size 20 mm complete all as specified and directed.

S&F in repair GI Flange of size 150 mm complete all as specified and directed.

S&F in repair GI Flange of size 100 mm complete all as specified and directed.

S&F in repair GI Flange of size 80 mm complete all as specified and directed.

S&F in repair GI Flange of size 50 mm complete all as specified and directed

S&F in repair Rubber or fibre board gaskets for flanged joints of size 100 mm complete all as specified and directed.

S&F in repair Rubber or fibre board gaskets for flanged joints of size 80 mm complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 using 40mm graded stone aggregate for coping, parapaet, thrust block and other similar items complete all as specified and directed.

S&F in replacement of Float valve for controlling of flow of water of size 50 mm complete all as specified and directed.

S&F in replacement of Float valve for controlling of flow of water of size 25 mm complete all as specified and directed.

S&F in replacement of Float valve for controlling of flow of water of size 20 mm complete all as specified and directed.

M&L for cross arms, bracings, supports, clamps and back plates fabricated from structural steel sections including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed complete all as specified and directed.

M &L for construction of Valve pit Chamber of size 900 mm x 900mm x 600 mm with PCC block masonary work, 75 mm thick PCC coping 1:2:4 using 20 mm graded stone aggregates, 3.15 mm thick MS sheet pit cover fixed on iron angle frame of size 40 mm x 6 mm thick suitale for 50/20 mm sluice valve .The valve pit cover and frame shall be painted with two coats of black synthetic enamel paint over a coat of red oxide primer.The foundation for valve chamber should be 150 mm thick in PCC 1:2:4 using 20 mm graded aggregates including necessary excavation, earth work and formwork etc complete all as specified and directed.

M&L for mixing of Alum (Aluminium Sulfate) used to purification of water as a chemical flocculant with raw water / clear water including maintaining the correct proportion complete all as specified and directed.

M&L for mixing of Bleaching Powder used to disinfect the water from bacteria with raw water / clear water including maintaining the correct proportion complete all as specified and directed.

M&L for mixing of Hypo Chlorine liquid (Sodium hypochlorite) with raw water / clear water including maintaining the correct proportion complete all as specified and directed.

Net Contract Sum will be after deducting Sch Of Credit of Rs. 49370.00

A P ENTERPRISES