SPECIAL REPAIR TO SOUTH GATE KHETRAPAL GATE MANEKSHAW GATE AND SECURITY WALL FROM SOUTH GATE TO MANEKSHAW GATE AT IMA DEHRADUN

Amount

Demolition of brick or stone masonary built in cement mortar including pre cast articles complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description and in any position complete all as specified and directed

Taking down cement plaster on brick or stone wall etc including raking out joints, hacking for key, scdrubbing down with water etc complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position complete all as specified and directed.

Demolition of cement concrete in ground floors and pavings n. Exc 15cm thickness (below or above) ground level complete all as specified and directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation, etc or for shafts, wells, cesspits, manholes, pier holes, etc n.exc 10 Sqm on plan and n' exc. 1.5 m in depth and getting out in any type soil complete all as specified and directed.

Excavation over areas n.exc 1.5m in depth and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in soil complete all as specified and directed.

Removing surplus excavated soil to a distance n.exc 50 metre & depositing where directed at a level n.exc 1.5 metre above the starting point complete all as specified and directed.

PCC 1:4:8 type D-2 using 40mm graded crushed stone aggregate as in foundation filling, mass concrete and sub base of floor etc complete all as specified and directed.

Brick work with sub class B bricks, straight or curved on exc 6m mean radious built in cement mortar (1:4) complete all as specified and directed.

Brick work with sub class B bricks styraight or curved on plan to any radious in half brick thick walls built in CM 1:4 complete all as specified and directed.

15-20mm thick Lakha stone (Granite) in path/vertical surface (square/rectangular) polished area of each tiles exceeding 0.36 sqm in floors/vertical surface etc. Over 15mm thick screed bed in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specified and directed

100 mm thick coloured PCC cobbled block in path (square/ rectangular) over and including 15 mm thick screed bed in CM 1:4, and block laid as per direction and joint shall be filled as per cobaled path pattern set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over and including 100 mm thick PCC 1:3:6 type C2 using 20 mm graded aggregate as per directions of Engr in Charge complete all as specified and directed.

Rounding to edges of stone slab one edge, such as in steps cooking platform and other similar situations complete all as specified and directed.

Sand stone of one piece decorative lamp of size 45 x 45 cm and height not less than 60 cm as per existing pattern of IMA main Gate and approved by GE. Complete all as specified and directed.

Stainless steel grade 304 letter of size 300mm x 50mm x10mm fixed on granite stone slab complete all as specified and directed.

10 mm thick earthenware Antique brick tiles of NATURAL SHAPE and colour, size of tile 230mm x 75 mm on vertical surfaces of wall over and including 10 mm epoxy based adhesive using suitable spacers 3-5mm thick complete all as specified and directed.

Rendering 15mm thick plaster on fair faces of brick work or concrete surface in CM 1:4 finished even and smooth without using extra cement and mixed with water proofing compound as per manufactures instructions, complete all as specified and directed Note- WPC will be measured paid as supply only under respective items separetely.

Preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed..

Preparation of new plastered surfaces of wall / ceiling and applying two coats of Apex paint ( Weather coat exterior paint) complete all as specified and directed. (work to be carried upto a height of 7.5m) .

Use & waste for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, and similar work, vertical or to batter including fair finished surfaces complete all as specified and directed.

Use & waste of form work to soffits of suspended slab such as roof slab, floor slab, landing and similar work not exceeding 200mm thick for fair finish surface complete all as specified and directed.

Use and waste of formwork to sides and soffits of floors or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports etc. and similar work of fair finished flat surface of concrete complete all as specified and directed.

Use and waste of form work to edges of concrete slabs n exc 20 cm complete all as specified and directed.

Use and waste of formwork to sides of concrete pillar, columns, posts strutts complete all as specified and directed.

RCC M -25 (Design Mix) using 20mm graded crushed stone aggregate as in foundations, including rafts, footing, foundation beams, plinth beams, bases for columns etc, basement slab, under-reamed piles and mass concrete etc complete all as specified and directed.

RCC M -25 (Design Mix) , type B-1using 20mm graded crushed stone aggregate as in beams, cantilever bressummers lintel over 1.5 m span etc complete all as specified and directed.

RCC M -25 (Design Mix) using using 20mm graded crushed stone aggregate as in slab supported on walls beams and columns in floor, roof, landing and in shelves and the like complete all as specified and directed.

RCC M -25 (Design Mix) using using 20mm graded crushed stone aggregate as in column ,pillars, piers,posts and struts complete all as specified and directed.

Mild steel TMT bars 8mm dia and over, cut to length, bent to shape required, including cranking , bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Mild steel TMT bars 5 mm dia and over upto and including 10 mm dia as in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Ornamental and intricate design mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc complete drilled for fixing of steel sheeting or other covering. Doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering running rails and guides) and hanging; also fastening and fixing complete all as specified and directed.

Rubberised polished glossy finish precast coloured cement concrete Interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 grade complete with & including 25mm thick sand cushioning layer including dismantling of existing damaged flooring etc complete, all as specified and directed.

Supply and laying or fixing or passing through pipe XLPE insulated, armoured, heavy duty electric cables 1100 volts grade with stranded aluminum conductor of size 25 sqmm 3.50 core laid in trench/wall/floor/trusses with including taking down existing cable saddle complete all as specified and directed.

Supply and laying or fixing or passing through pipe XLPE insulated, armoured, heavy duty electric cables 1100 volts grade with stranded aluminum conductor of size 06 sqmm 2 core laid in trenches /duct /wall /floor etc complete all as specified and directed.

Un-reinforced precast concrete cable cover class LV type1 flat size250 mmx 150 mm x40 mm as protection to under ground cable laid dry flat adjjoining each other complete all as specified and directed

Supply and filling sand with clean dry fine sand unwashed including gently punning around cables in trenches for cable protection complete all as specified and directed. NOTE: - Punned thickness shall be measurement & paid.

GI pipe light grade ISI marked 40mm bore for cable protection fixed to poles/along wall/floor/under road/across the drain or nallah with calmps, bolts, nuts & washers etc complete all as specified and directed.

GI pipe light grade ISI marked 50mm bore for cable protection fixed to poles/along wall/floor/under road/across the drain or nallah with calmps, bolts, nuts & washers etc complete all as specified and directed.

LED flood light fitting 50 watt energy saving and enviromental friendly long liife exclusive innovative made up of pressure die cast aluminium housing with high power LED as lightning source, suitable for high lighting archtectural features or area lighting also suitable for rough services/installations, etc complete including taking down existing fitting any type and in any position complete all as directed. Make: Havells cat part No. JETAQUANTOFLS50W LED765SYMPC or equivalent in Philips / Wipro.

Pole mounted LT junction box, waterproof and fire proof, sheet moulding compound (SMC) Sintex Make box of inside size 250mm x200mmx100mm deep complete with 4 Nos terminal end, aluminum strip of 20x4 mm size fixing cable end terminal and 3 Nos MS bolts and nut of size 8 mm dia x 30 mm long and MCB mounting rail with 6 amp MCB SP welded with box fixed on pole with MS clamp 25 mm x 3 mm MS strip duly painted and testing including taking down existing complete all as specified and directed.

Bus bar chamber pedestal type of size 75cmx60cm x40cm, out door, dust & vermin proof, front opening made out of 2.00 mm thick MS sheet duly painted and consisting of aluminium bus bar 3 phase and neutral 4 Nos 400 Amp fixed on insulators and one MCCB TPN 200 Amp, 25 KA breaking capacity including fixed in PCC 1:3:6 including danger plate etc including taking down existing LT feeder pillar with MCCB complete all as directed.

Supplying, laying, jointing and testing PVC insulated, multi core stranded copper conductor cable, 1100 volts grade, cross-sectional area 1.5 Sqmm 3 core complete including disconnecting & taking out existing cable etc complete all as specified and directed.

Post top lantern fully cast aluminium body finished with polyurethane paint (with prior treatment) with acrylic window cover with B 22 holder, LED lamp 12 watt and spigot dia 62 mm including taking down existing fitting any type and any position complete as all as directed. Make- Mepro electricals Cat part No PTL -08 or equivalent in Bajaj and Crompton Greaves

Post top lantern fully cast aluminium body finished with polyurethane paint (with prior treatment) with acrylic window cover with B 22 holder, LED lamp 30 watt and spigot dia 62 mm including taking down existing fitting any type and any position complete as all as directed. Make- Mepro electricals Cat part No PTL -0008 or equivalent in Bajaj and Crompton Greaves

LED strip sky cave 5mm WW with driver 24 watt output 3000K including taking down existing fitting any type and any position complete all as specified and directed.

Earthing complete with galvanized iron earth plate electrode 600mm x 600mm x 6mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) vertically, with top edge of plate not less than 1.5 metre below normal ground level connected to GI earth strip 25mm X 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 of MES Schedule Part-I connecting to earthing test point & to main switch board and testing on completion with and including necessary excavation and earth work in any type soil, earth lead connected to earth test point & to main switch board etc with & including adequate quantity of charcoal dust and common salt, test point, PCC (1:3:6) type C-1 (using 20mm graded BT stone aggregate) for earth pit with 40 x 40 x 6mm mild steel angle iron frame for cover, internal surface of concrete shall be given 10mm thick plaster in CM 1:4, pre cast RCC (1:2:4) type B-1 (using 20mm graded BT stone aggregate) 40mm thick cover, reinforced with 8mm dia deformed or TMT bars 3 Nos both way with 12mm dia round bar handle, GI medium grade watering pipe 20 mm dia with funnel and wire mesh and 15mm dia GI light grade earth lead protection pipe etc complete all as specified and directed. NOTE: (i) Earth lead wire and its protection pipe upto and including 7.5 mtr only from the top of earth electrode are included under this item. (ii) Any joints in earth lead from earth electrode to test point shall not be allowed/permitted. (iii) If the desired earth resistance is not found within permissible limit shall be re done by contractor at no extra cost.

M/S RAJESH KUMAR GOYAL