Construction Additional Accommodation on Govt Sen Sec School Bhatkidhar in Tehsil Thunag Distt Mandi SH C/o Building portion WS SI site development septic tank and rain water harvesting system

Amount

Cutting in earth work all kinds of soils and disposal of excavated earth upto a lead of any metres such as pick work , jumper work, pick work,pick jumper blasting work, blasting work in soft and hard rock conglomrate rock or saturated soil and its intermediate classification of soil including chiseling/wedging out of rocks (where blasting is prohibited) and pumping or bailing out of watering/dewatering upto any lift stacking the excavated soil clear from the edge of excavation and then returning the stacked soil in layers when required into plinth sides of foundations consolidation each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed by the Engineer-in charge within any leads including carriage of materials with in all leads, lifts and other incidentals.

Excavation in foundation, trenches etc. in earth work in all kinds of soil such as pick work, Jumper work, blasting work in soft and hard rock, conglomerated rock or saturated soil and its intermediate classification of soil, chieseling work and wedging out rock (where blasting is prohibited) and pumping or bailing out watering/dewatering upto any lift, stacking the excavated soil upto any lead from the edge of excavation and then returning the stacked soil in layer when required into plinth, sides of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Excavation in drain and channels etc. in earth work in all kinds of soils such as pick work, jumper work, pick jumper work , pick jumper blasting work , blasting work in soil and hard rock conglomerate rock or saturated soil and its intermediate classification of soil including chiseling/wedging out of rocks (where blasting is prohibited) and pumping or bailing watering/dewatering including dressing of sides and bed and disposing of excavated earth upto any leads and lifts disposted earth to be leveled and neatly dressed as directed by the Engineer-in charge within any leads including carriage of materials with in all leads, lifts and other incidentals.

Providing form work with steel plates 3.15mm(Three point fifteen millimeter) thick welded with angle iron in frame 30x30x5mm(Thirty millimeter into thirty millimeter into five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and bellies in any height of propping and centering below supporting floor to ceiling upto floor all level and removal of the same for in situ-reinforced concrete and pain concrete work including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge in:- Vertical surface such as walls(any thickness) and the like including attached pilasters, buttersses plinth and string courses and the like

Foundation, footing basis of columns etc. and mass concrete .

Flat surfaces such as soffits of suspended floors, roofs, landings and the like Floors etc upto any thickness.

Beams, cantilever, girders and lintels sides and soffits of beams, beam haunching, cantilevers, bressumers and lintels in any depth in all height from floor..

Columns, pillars, Posts and struts, Square, rectangular or polygonal in plan

Stair cases with sloping or stepped soffits excluding landing

Edges of slabs and breaks in floors and walls in any width.

Providing and laying cement concrete 1:5:10 ( one cement : five sand : ten graded stone aggregate 40mm.(Forty millimetre) nominal size mechanically mixed and vibrated with 15% (fifteen percent) plum and curing complete excluding the cost of form work in retaining walls/breast walls. The size of plum shall usually be 150 mm to 300 mm (one hundred fifty millimetre to three hundred millimetre) as per HP.PWD specification and direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing 100mm (one hundred millimetre) diameter poly Vinyl chloride pipe in Weep holes in brick masonry/stone masonry, plain/reinforced concrete and retaining /breast walls etc. extending through the full width of the structure with slope of 1V:20H towards drainage face complete as per drawings and technical specifications and as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and laying cement concrete mechanically mixed and vibrated 1:5:10 ( one cement : five sand : ten graded stone aggregate 40mm.(Forty millimetre) mechanically mixed and curing complete excluding the cost of form work in foundation and plinth as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying cement concrete 1:4:8 ( one cement: four sand: eight graded/ crushed stone aggregate 40mm (Forty millimetre ) nominal size) mechanically mixed and vibrated and curing complete excluding the cost of form work in foundation and plinth as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Backfilling behind abutment, wing wall, R/walls and B/walls complete as per drawings and technical specifications clause 1204.3.8 including carriage of material within all leads and lifts and other incidentals.

Stone soling/boulder filling dry hand packed in under floor as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and laying reinforced cement concrete design mix M-25 (twenty five) grade mechanically mixed and vibrated and curing complete excluding cost of form work and reinforcement for reinforced cement concrete work. The mix shall be designd as per requirement of I.S code and P.W.D specification. The design mix will be got approved from the Engineer - in - Charge prior to the casting. The theoritical consumption of cement for the item shall be worked out as per approved design mix as per I.S code including carriage of materials with in all leads, lifts and other incidentals . Foundation, footing basis of columns etc. and mass concrete .

Suspended floors, roofs ,landings and shelves and their support, balconies, beams, girders, breasumers and cantilevers upto Floor any Level

Columns, pillars posts and struts square rectangular polygonal in plain upto Floor any Level

Stair cases (except spiral stair cases) excluding landing but including preparing of the top surface and finishing of nosing upto Floor any Level

Wall (any thickness but not less than 0.10 m thickness) attached pilasters, buttresses, plinth and string courses etc. from top of foundation level upto floor all level

Providing and laying reinforced cement concrete design mix M-20 (twenty) grade mechanically mixed and vibrated and curing complete excluding cost of form work and reinforcement for reinforced cement concrete work. The mix shall be designd as per requirement of I.S code and P.W.D specification. The design mix will be got approved from the Engineer - in - Charge prior to the casting. The theoritical consumption of cement for the item shall be worked out as per approved design mix as per I.S code in string course, copings, bed plates, anchor blocks, plain windows sills and the likesu upto floor all level including carriage of materials with in all leads, lifts and other incidentals .

Providing Tor steel reinforcement for R.C.C. work including bending, binding and placing in position complete including cost of binding wire up to any level as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and laying 20 cm. (twenty centimetre) thick composit stone masonry with stone facing of chisel dressed stones one line dressed in cement mortar 1:6 (1 cement :6 sand) and concrete backing with cement concrete 1:3:6 (1 cement: 3 sand: 6 graded stoneaggregate 20 mm (twenty millimetre) nominal size on inner face of walls including centring,shuttering and propping complete up to floor any level as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Precast concrete block masonry (including quoin blocks, jamb blocks, closer etc) with solid concrete blocks of approved size made of cement Concrete, 1:3:6 (One Cement: Three Sand: Six graded stone aggregate.) 40 mm (Forty millimeter) nominal size and down gauge in cement mortar 1:6 (One Cement: Six Sand) in foundation and plinth upto floor any level as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Precast concrete block masonry in partition walls 10 cm (ten centimetre) thick with solid block ofa pproved size (including quoin blocks, jamb blocks, closer etc) with solid concrete blocks of approved size made of cement Concrete, 1:3:6 (One Cement: Three Sand: Six graded stone aggregate.) 40 mm (Forty millimeter) nominal size and down gauge in cement mortar 1:6 (One Cement: Six Sand) in foundation and plinth upto floor all level as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Brick work using common burnt clay building bricks in Superstructure above plinth level in Cement mortar 1:6 (One Cement : Six Sand) second Class Bricks as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.upto Floor any Level

Half brick masonry in common burnt clay building bricks in cement mortar 1:3 (one Cement :Three Sand) (2nd Class Brick)in super structure above plinth level upto all floor level as per the direction of Engineer-in-chargeincluding carriage of materials with in all leads, lifts and other incidentals. upto Floor any Level

Brick work using common burnt clay building bricks in foundation and plinth in Cement mortar 1:6 (One Cement : Six Sand) second Class Bricks as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals .

Half brick masonry in common burnt clay building bricks in cement mortar 1:3 (one Cement :Three Sand) (2nd Class Brick)in foundation footing & plinth as per the direction of Engineer-in-chargeincluding carriage of materials with in all leads, lifts and other incidentals .

Providing 1st class deodar wood work in frames of doors,windows,clerestory,windows and other frames wrought,framed and fixed in position complete as per specification and as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and fixing 35 mm (thirty five millimetre) thick including black enamelled M.S. butt hinges flush door shutters interior grade, commercial type, core of black-board construction with frame of first class hard wood and well matched commercial ply veneering with vertical grains of cross bands and face veneers on both faces of shutters as per specification and as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and fixing 35mm (thirty five millimetre) thick 2nd class deodar wood panelled glazed or panelled and glazed shutters for doors windows and clerestory windows including black enamelled iron butt hinges with necessary screws as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing angle iron cupboard frames frames manufactured from M.S.Angle iron section 25X25X5mm (twenty five into twenty five into five millimetre) thickness including hinges jamb,lock jamb,beed and if required angle thrashold of mild steel angle 25X25 mm (twenty five into twenty five millimetre) welded or rigidly fixed by mechanical means,lugs with split end tails to each jamb including steel butt hinges 2.5 mm (two point five millimetre) thick with provision for locking arrangement and shock absorber as specified and applying a coat of approved steel primer after preteatment of the surface as directed by Engineer-in- Charge.

Providing and fixing 19mm (nineteen millimetre) thick Commercial Board water proof shutters with 6mm (six millimetre) thick hard wood edging with fixing PGI Sheet nickel plated piano hinges with screws etc complete as per specification and as per the directions of Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 2nd class deodar wood wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm (zero point fifty six millimetre) for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screw etc complete as per specification and as per the directions of Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals

Providing and fixing Plain M.S. grills of required patterns in wooden frames of windows etc. with M.S. Flats, square or round bars with round headed bolts and nuts or by screws. as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing anodized aluminium sliding door bolt anodized colour and shade with bolts and nuts screws etc. complete.300x16mm (three hundred x sixteen millimetre) as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing anodized aluminum tower bolts (barrel type ) anodized trans parent or dyed to equired shade and colour with screws etc. complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. 200x10mm (Two hundred x ten millimeter)

150x10mm (One hundred fifty x ten millimeter)

100x10mm (One hundred x ten millimeter)

Providing and fixing aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. 125 mm (One hundred x twenty five millimeter)

100 mm (One hundred millimeter)

75 mm (seventy five millimeter)

Providing and fixing bright finished brass 100mm.(One hundred millimeter) Mortice latch and lock and a pair of levers, handles with necessary screws etc. complete (indian make of approved quality) as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 100mm (One hundred millimeter) bright finished brass floor door stopper with rubber cushion screws etc. to suit shutter thickness complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing bright finished hard drawn hooks and eyes as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. 250mm (Two hundred fifty millimeter)

200mm(Two hundred millimeter)

Providing and fixing 115mm (one hundred fifteen millimeter) bright finished brass heaps and stapples (safety type) with necessary screws etc complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 150mm (one hundred fifty millimeter) oxidized M.S. single acting spring hinges with necessary screws etc. complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 19mm (nineteen millimetre) thick Commercial Board water proof shutters for up boards i/c fixing with nickel plated piano hinges with screws etc complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

40 mm (forty millimetre) thick Cement concrete flooring 1:2:4 (1 cement : 2 sand:4 graded stone aggregate 20 mm (twenty millimetre) nominal size laid in one layer finished with a floating coat of neat Cement complete as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. Up to Floor any level.

25 mm (twenty five millimetre) thick wooden flooring of 1st class deodar wood laid over C.C. slab (to be paid separately) ( thinly coated with thin layer of hot bitumen blown type) @ 2.45 kg per sq m (two point forty five kilogram per square metre) including fixing of wooden planks of size 40 x 200 mm (forty into two hundred millimetre) in position over wooden frame work 750 mm x 625 mm (seven hundred fifty millimetre into six hundred twenty five millimetre) fixed in c.c. floor including planning and levelling complete as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.Up to Floor any level.

Providing and laying 20 mm (twenty millimetre) thick heavy duty vitrified acid and alkali resistant stain resistant 30cm x 30cm (thirty centimetre into thirty centimetre) tiles Babylon white grey colour of Durastone of approved shade of Somany/NITCO/Kajaria or equivalent make laid in floors, treads of steps and landings on a bed of 12mm (twelve millimetre) thickness of cement mortar 1:3 (one cement : three sand) jointed with neat cement slurry mixed with pigment to match the shade of tiles (wherever required) incliding rubbing and polishing complete with tiles of white shades as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals

Providing and laying 20mm (twenty millimetre) thick heavy duty vitrified acid and alkali resistant stain resistant 30cmx 30cm (thirty centimetre into thirty centimetre) tiles Babylon white grey colour of Durastone of approved shade Somany/NITCO/Kajaria or equivalent make laid in skirting and risers of steps upto any height on 12mm (twelve millimetre) thickness of cement mortar 1:3 (one cement : three sand) jointed with neat cement slurry mixed with pigment to match the shade of tiles (wherever required) incliding rubbing and polishing complete with tiles of white shades as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying 10mm (ten millimetre) thick full body vetrified tiles of Asian/Johnson/Kajaria or equivalant 600x600mmx10mm (six hundred into six hundred millimetre into ten millimete) manufactured of approved shade and colour in flooring, treads of steps and landing laid over 12mm (twelve millimetre) thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete. as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.Up to Floor any level.

Providing and fixing 10mm (ten millimetre) thick full body vetrified tiles of AGL/Johnson/Kajaria/Orient Bell or equivalant 600x600mmx10mm (six hundred into six hundred millimetre into ten millimete) manufactured of approved shade and colour in skirting risers of steps and dados on 12mm (twelve millimetre) thick cement mortar 1:3 (1 cement : 3 sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. upto floor any level.

Providing and laying 8 mm (eight millimetre) thick Anti Skid Ceramic tile 300 x 300 mm (three hundred into three hundred millimetre) of AGL/Johnson/Kajaria/Orient Bell or equivalant manufactured of approved shade and colour in flooring, treads of steps and landing laid over 12mm (twelve millimetre) thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete. as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. upto floor any level.

Providing and laying 8 mm (eight millimetre) thick Anti Skid Ceramic tile 300 x 300 mm (three hundred into three hundred millimetre) of AGL/Johnson/Kajaria/Orient Bell or equivalant manufactured of approved shade and colour in skirting risers of steps and dados on 12mm (twelve millimetre) thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete. as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. upto floor any level.

Providing and laying 10mm (ten millimetre) digital ceramic tile of size 300 x 600 mm (three hundred into six hundred millimetre)in skirting risers of steps and dados on 8 mm (eight millimetre) thick cement mortar 1:3(1cement: 3 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone including rubbing and polishing complete. as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. upto floor any level.

Providing and fixing wall paneling of 12 mm (twelve millimeter) thick pre laminated particle board (one side) of approved brand of soft wood 4x4 cm frames @60 cm center to center on both side fixing with rawl on wooden plugs and screws and showing 8 mm wide in elevation and finished teak wood beading outlay 25x12 mm deep groves of required pattern of 25x12mm(twenty five millimeter x twelve millimeter) /Cornish out to 75x60mm(seventy millimeter x sixty millimeter) of different pattern in top middle and corner joints including polishing and painting groves complete as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. upto floor any level.

Providing and laying black granite stone in flooring 20mm (twenty millimetre) (average) thickness base of cement mortar 1:3(1cement: 3 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone including rubbing and polishing complete as per directionof Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals.

25 mm (twenty five millimetre) thick Kota stone slab flooring 20 mm (Twenty millimetre) (average) thick base of cement mortor 1:4 (1 cement :4 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete as per directionof Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals.

Kota stone slab 25 mm (twenty five millimetre) thick in risers of steps,skirting dado and pillars laid on 12 mm (twelve millimetre) (average) thick cement mortar 1:3 (1 cement :3 sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing complete within all leads, lifts and other incidentals and as per the directions of Engineer-in-Charge.

Providing and laying red sand stone slab flooring 40mm average thick on 20mm average thick base of cement mortar 1:4 (1 cement : 4 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and granite polish finish complete within all leads, lifts and other incidentals and as per the directions of Engineer-in-Charge.

Providing and fixing 0.60mm (Zero point six zero milimetre) thick preprinterd steel sheet in roofing with hot dipped metallic zinc coasted sheet with top coat of regular modified polyester (RNP) organic coating of 20 (Twenty) microns over 5 ( five) micons primer coating to back coast of polyester of 5 microns over 5 microns primer coating including fixing with screws, prepainted iron J or L hooks, bolts and nuts 6mm(six milimetre) dia with prepainted limpet and rubber washer complete with all accessories as required as per specifications and as per direction of Engineer-in-Charge including carriage of materials with in all leads, liftsother incidentals.

Providing and fixing ridges or hips 60 cm (Sixty centimeter) overall with 0.60 mm (Zero point sixty millimeter) thick preprinted steel sheets in roofing with hot dipped metallic zinc coated sheets with top coat or regular modified polyester organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating + back coat of polyester of 5 (Five) microns over 5 (Five) microns primer coating including fixing with preprinted iron J or L hooks, bolts & nuts 6mm(Six millimeter) dia and preprinted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing valley 90cm (ninety centimetre) overall 0.60mm (Zero six zero milimetre)thick prepainted steel sheet in roofing with hot dipped metalic zinc coated sheet with top coat og regular modified polyster organic coating of back coat of polyster of 5 microns over 5 microns primer coating including fixing with screws, preprinted iron J and L hooks,bplts & nuts & nuts 6mm (Six milimetre)dia and prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals

Providing and fixing flushing 38cm(Thirty centimeter) overall with 0.60mm ( Zero point six milimetre)thick pre painted sheet in roofing with hot dipped metallic Zink coated sheet with top coat of regular modified polyester organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with pre painted J or L hooks, bolts and nuts 6mm(Six milimetre) dia meter & pre painted G.I. limpet & bitumen washers complete with all accessories as required as per the direction of Engineer-In- charge.

Providing and fixing on wall face 100mm (One hundred milimetre) dia PVC(D-Plast) rain water pipes of working pressure not less than 4.5 Kg/sqm(Four point five kilogram per square metre) including filling the joint with approved adhersive complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing on wall face (D-Plast) accessories for rain water pipes including filling the joint with approved adhesive complete as per the direction of Engineer-in-Charge of materials within all leads, lifts and other incidentals. PVC Plain Bend 100mm(One hundred milimetre) dia.

Shoe 100mm (One hundred milimetre) dia.

Providing and fixing M.S. BP Sheet 1.66 mm (One point sixty six milimetre) to 2mm (Two milimetre) thick in eves board/ facia/soffit/ceiling including cutting ,fixing and welding to steel roof members and applying a coat of red lead primer complete as per direction of the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Steel work welded in built up sections, trusses and framed work,including cutting, hoisting fixing in positiobn and applying a priming coat of red lead paint as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals in: Trusses and trussed purlins in buildings including carriage of materials with in all leads,lifts and other incidentals.

Gratings framed guard bars laddeds railing brackets and similar works including carriage of materials with in all leads, lifts and other incidentals.

In beams joists channels ,angles , tee ,flats with connecting plates or angle cleats as in main and cross beams,hip and jack rafters,purlins connected to common rafters and the like.

Providing and fixing 62.5mm x 75mm (sixty two point five millimetre into seventy five millimetre) hand rails in 1st class Indian teak wood straight length complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lift and other incidentals.

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm (twenty into ten into two milimetre) braced with flat iron diagonals 20x5mm (twenty ito five milimetre) size with top and bottom rails of T iron 40x40x6mm (forty into forty into six milimetre) with 38mm(thirty eight milimetre) dia steel pully complete with bolts and nuts locking arrangements, stoppers, handles, including carriage of materials within all leads, lifts and other incidentals.

6mm (Six millimeter) cement plaster to ceiling in cement mortar 1:3 (one Cement : three Sand) as per the directions of Engineer-in-Charge including carriage of materials within all leads, lifts and other ncidentals.

15mm (fifteen milimetre) cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering up to all floor level includingarises, internal rounded angles,chamfers and/or rounded angles not exceeding 80mm(eighty milimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement:six sand)as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

15mm (fifteen milimetre) cement plaster in single coat on the fair side of brick/concrete/stone wall for interior plastering upto floor all level including arises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (Eighty milimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement:6 sand) as per the direction of Engineer-in-Charge including carriage of materials within all leads, and lifts other incidentals.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete s per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture on undecorated wall surfaces to give an even shade i/c thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth i/c applying of putty a required for making the surface as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth Priming coat with distemper primer as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Distempering(one coat) with oil bound washable distemper with oil bound distemper on ceiling and/or sloping roofs of approved brand and manufature and of required shade,on decorated wall surfaces to give an even shade,after thoroughly brushing the surface clean of all grease,dirt,loose pieces of scales and also including preparing the surface even and sand papered smooth as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease,dirt and other forein matter sand papering and knotting ready mixed paint with wood priming pink of approved brand and manufacture (Nerolac/Asian Shalimar) conforming to IS: 3536-1966 brushing as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Painting two coats (excluding priming coat) on new wood and wood based surfaces with ready mixed paint brushing to give an even shade including cleaning of oil, grease,dirt and and other foreign matter sand papering and stopingready mixed paint other thanwhite as per direction od Engineer-in-including carriage of materials within all leads, lifts and other incidentals.

Applying priming coat over new steel and other metal surfaces after and including preparing the surface by thoroughly cleaning oil grease dirt and other foreignmatter and scoured with wire brushes fine steel wool scrubers and sand paper complete with ready mixed priming pant brushing red leadred oxide/zinc oxide chrome as per the direction of Engineer-in-Charge including of materials within all leads,lifts and other incidentals.

Painting two coats (excluding priming coat) on new steel and other metal surfces surfaces with enamel paint brushing to give an even shade including cleaning the surface of all dirt, dust and other foregin matters Enamel paint other than white including carriage of materials with in all leads, lifts and other incidentals.

Making plinth protection with flag stone flooring 40 mm (fourty millimetre) thick over a bed of 15cm (fifteen centimetre) with rammed earth and cement pointing 1:3 (1 Cement : 3 Sand) in proper shape as per the direction of Engineer-in-Charge including of materials within all leads,lifts and other incidentals.

Providing under layer for plinth protection of 75mm (Seventy Five millimetre) thick (unconsolidated) bed dry brick/stone aggregated 40mm (Forty millimetre) nominal size well rammed and consolidated and grouted with fine sand including preparation of ground as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Constructing course rubble dressed "U" shape open surface drain with side wall 15X22cm (fifteen into twenty two) in cement mortor 1:6 (one cement: six sand) and in side plstring with cement plaster 1:3 (one cement : three sand ) including earth work and laying 10cm (Ten Centimetre) cement concrete 1:5:10 (one cement :five sand:ten graded stone aggregate 40mm (Forty millimetre) nominal size) and 7.5cm (seven point five centimetre) cement concrete 1:2:4(one cement :two sand ;four graded stone aggregate 20mm (Twenty millimetre) nominal size) and finishing with a floating coat of neat cement and curing complete as per standard design as per the entire satisfaction and direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing High Lax Cilicate perforated water proof board 600 x 600 x 8 mm (six hundred into six hundred into eight millimetre) in ceiling fixed over aluminium Tee sections with screws and including hangers complete as per the entire satisfaction and direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 612 mm (six hundred twelve millimetre) thick green chalk board (non magnetic with superior quality framing specially anodized aluminium profile 20x15 mm (twenty into fifteen millimetre)with corners of black surafce shall be non porous cermaic particle on the top on the green surface foer the writing with chalk over 11 mm (eleveen millimetre) thick particle board which shall have backing material of galavanized sheet 0.28 mm (zero point two eight millimetre) approx the board shall be fixed on the wall with clamps as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Filling with brick aggregate in soak pit complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals

Providing and fixing to wall ceiling and floor galvanized mild steel tubes (Medium grade) tube fitting and clamps including making good the wall, ceiling and floors as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. . 20mm (Twenty Millimetre) nominal bore

25 mm (Twenty Five Millimetre) nominal bore

Providing and fixing to wall and ceiling and floor Polythene Aluminium composite pressure pipe of 15mm (fifteen millimetre) dia of Kitec confirming to ISI 15450-2004 including making good the wall, ceiling and floor as per specification and the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying in trenches, galvanized mild steel tubes (medium grade), tube fittings (earth work in trenches to be measured and paid separately) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. . 25 mm (Twenty Five Millimetre) nominal bore

Making connection of galvanized steel distribution branch with galvanized mild steel main 20mm(Twenty Millimetre) to 40mm (Forty Millimetre) nominal size bore by providing and fixing tee including cutting and threading the pipes complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Construction chamber 300mm x 300mmx500mm (Three Hundred x Three Hundred x Five Hundred millimetre) inside size for stop cock with C.I. surface box 100mm x 100 mm x 75mm (One Hundred x One hundred x Seventy Five millimetre) (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (one cement : two sand :four graded stone aggregate 20mm (Twenty millimetre) nominal size) 75mm (Seventy Five millimetre) thick foundation concrete 1:5:10 ( one cement : five sand : ten grades stone aggregate 40 mm (Forty millimetre) nominal size) and inside plastering with cement mortar 1:3 (one cement :three sand) finished with a floating coat of neat cement including curing complete with 100 mm (Hundred millimetre) thick walls of brick masonry in cement mortar 1:5 (one cement: five sand) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and. fixing Anglo Indian Universal WC No. 2061 with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1(1 cement : 1 sand) of Cera/Hindware/jaguar as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing white plastic seat (solid/ hollow type) and cover for wash down water closet with C.P. Brass hinges and rubber buffers of Cera/Hindware/jaguarcomplete as per the direction of Engineer in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing vitreous China wash down, water closet Orissa Pattern No.2071 squatting pan (Indian type W.C pan) size 580mm x 440 mm (five hundred eighty millimetre into four hundred forty millimetre) (Earth work, bed concrete, foot rest and trap to be measured and paid for separately) of Cera/Hindware/jaguar as per the direction of Engineer in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing PTMT White colour high density polyethylene / poly propylene 10 litres capacity ( full flush) European standard control low level flushing cistern No. 2602 of Cera/Hindware/jaguar with fittings with a pair of brackets with fittings such a lead valve, syphon, 15mm (fifteen millimetre) nominal size PVC ball valve with polythene float, with push button, couplings for connections with inlet, outlet and over flow pipe, 40mm (forty millimetre) dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 110 mm (one hundred ten millimetre)dia PVC ‘P’ or 'S' trap for water closet (squatting pan) ISI marked including jointing the trap with the pan and PVC pipe with approved adhesive etc. complete.as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing PTMT jet spray of Cera/Hindware/jaguar with 1.5 mtr. (one point five metre) Tube complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing white glazed fire clay stallurinal flat back large No. 5001 with automatic flushing cistern of Cera/Hindware/jaguar with fittings R.S. or C.I. Brackets standard size C.P. brass flush pipe spreaders with unions and clamps (all in C.P. brass) C.I. Trap with outlet grating and other coupling in C.P. brass including painting of cistern and fittings, cutting and making good the walls and floors where requiredas per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing C.P. brass flush pipe / spreaders for urinal with fitting such as unions, clamps etc. (all in C.P. Brass) including cutting holes and making good the same 32mm (thirty two millimetre) nominal bore as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing vitreous china wash basin No 1007 of size 550 x 400 mm (five hundred fifty into four hundred millimetre) of Cera/Hindware/jaguar with single hole for pillar tap with cast iron or mild steel brackets painted white including cutting holes and making good the same but excluding fittings flat back as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing vitreous China pedestal for wash basin complete recessed at the back for the reception of pipes and fittings as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing Vitreous China 600mm x 450mm x 250mm (six hundred millimetre into four hundred fifty millimetre into two hundred fifty millimetre) laboratory sink with C.I. or M.S. brackets painted white including cutting holes in walls and making good the same but excluding fittings as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 32 mm (thirty two millimetre ) dia diametre C.P brass waste for wash basin or sink of approved brand and menufature as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing M.I. Union for wash basin or sink 32mm (thirty two millimetre ) dia size including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing 32 mm (thirty two millimetre ) dia C.P. Bottle Trap for wash basin or sink as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing 600mm x 450 mm ( six hundred x four hundred fifty millimetre) bevelled edge mirror of superior glass mounted on 6mm thick A.C. Sheet or plywood sheet and fixed to wooden plugs with C.P. Brass screws and washers as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing C.P. Brass Towel rail No 1581 of Jaguar complete with C.P. Brass brackets fixed to wooden plugs with C.P. Brass screws 600mm x 20mm (six hundred x twenty millimetre) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 600mm x 120 mm (six hundred x one hundred twenty millimetre) glass shelf with C.P. Brass bracket and guard rail complete, fixed to wooden plugs with C.P. Brass screws as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing toilet paper holder No 1533 of Jaguar/ESS-Ess or its equivalent in C P Brass as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing liquid soap container with C.P. Brass lid and brackets fixed to wooden plugs with C.P. Brass screws as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing C.P brass soap dish no. 1531 of Jaguar or its equivalent complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 15 mm (Fifteen millimetre) dia C.P. Brass bib tap with Capstan head of Jaguar as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing 15 mm (Fifteen millimetre) dia C.P. Brass pillar tap with Capstan head 15 mm dia of Jaguar as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing 15 mm (Fifteen millimetre) dia C.P. Brass stop cock as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing 15 mm (Fifteen millimetre) dia PTMT concealed stop cock with flange of Jaguar and approved quality and colour as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing P.V.C. connection with Brass unions 300/450 mm (three hundred/four hundred fifty millimetre) 15 mm(fifteen millimetre) nominal size as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 32mm (thirty two millimetre) nominal bore C.P. Brass waste, and plug for glazed ware sinks, basins, etc. with long screwed shank and flynut and fixed to steel pipe including vulcanite plug, brass chain and stud as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing brass full way valve with wheel as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. 15 mm (fifteen millimetre) nominal bore

20 mm (twenty millimetre) nominal bore

25 mm (Twenty Five Millimetre) nominal bore

Providing and fixing brass ball valve (horizontal plunger type) High pressure with polythene plastic floats 15 mm (fifteen millimetre) nominal bore as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals

Providing and fixing PVC water storage tank of ISI : 12701 marked, G.I. inlet and outlet connection, 15mm (fifteen millimetre) nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level 1000 litres(one thousand litres) net capacity tank as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete.110*90 mm (one hundred ten x ninty millimetre) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals

Providing and fixing high pressure PVC spigot and socket waste and ventilating pipes confirming to ISI -15328 SN8 of Supreme/Fenolex/Kitech marked including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals 110 mm dia (one hundred ten) dia

150 mm dia(one hundred fifty) dia

Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm (three millimetre) thick bolts and nuts complete /including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals

Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC door bend with oval access door insertion rubber washer 3 mm Three millimetre) thick bolts and nuts ISI market complete including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals

Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC Collar ISI marked including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals

Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC plain bends ISI marked including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals

Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals

Providing and fixing PTMT grating round of approved quality and colour 100 mm (one hundred millimetre) nominal dia as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and fixing PTMT urinal spreader of approved quality and colour as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing Grab Bar of Jaguar WAC-WHT-BR0600 692 mm satinless 40mm dia steel pipe at 78 m (seventy eight metre) height with MS plate as the position of seat as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying (to level or slopes) and jointing reinforced concrete light duty non pressure pipes I.S. Class N.P.2 or P of the following internal diameter with collars and butt ends prepared for collar joint including testing of joints complete. 150 mm (one hundred fifty millimetre) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying Cement concrete 1:5:10 ( one Cement : five Sand : ten graded stone aggregate 40 mm (forty milimetre) nominal size) in hunching of S.W. pipes of the following internal diameters, Including concrete for beddings, necessary form work and curing complete.150 mm (one hundred millimetre) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing stoneware gully trap grade 'A' complete with C.I grating, brick masonry chamber in cement mortar 1:5 (one cement :five sand)and water tight C. I. cover with frame of 300mmx300mm( three hundred millimetre x three hundred millimetre) size (inside) the weight of cover to be not less than 4.53kg and frame to be not less than 2.72kg (two point Seventy two kilogram) square mouth trap 150*100 mm ( one hundred fifty x one hundred milimetre)size P or R type as per the direction of Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals.

Supplying cast iron cover with frame for manhole for frame of internal dimension 455 x 610 mm (four hundred fifty five into six hundred ten millimetre) rectangular CI cover the weight of cover to be not less than 38 kg (thirty eight kilogram) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Constructing manhole with R.C.C. top slab in1:2:4 mix in ( one cement : two sand : four graded stone aggregate 20mm (twenty milimetre) nominal size) foundation concrete1:4:8 (one cement : four sand : eight )graded stone aggregate 40mm (forty milimetre)nominal size) inside plastering 15mm (fifteen millimetre) thick with cement mortar 1:3 (one cement three sand) finished with a floating coat of neat cement and making channels in concrete 1:2:4 mix (one cement : two sand : four graded stone aggregate 20mm (twenty millimetre) nominal size) finished smooth complete including curring and testing Inside size 800 x 800 mm and 1000 mm (one thousand millimetre) deep including C.I. cover with frame (light duty single seal pattern - I) 455 x 610 mm (four hundred fifty five into six hundred ten millimetre) internal diameters total weight of cover and frame to be not less then 38 Kg. (thirty eight kilogram) (weight of cover 23 Kg. (twenty three kilogram) Weight of frame 15 Kg.(fifteen kilogram) with 300 mm (three hundred millimetre) thick walls of square rubble masonry coursed with hard stones of approved quality in cement mortar 1:3 (one cement : three Sand) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

MOHAN LAL THAKUR