E.T.No.-EDC(USN)62/2025-26

Annexure-A (LABOUR CHARGES)

Earthing of support with M.S. Earth rod of 2.5 meter long by hammaring of M.S. Rod to proper depth and connecting the earth electrode with the help of G.I. wire as per construction manual..

Fabrication of MS Channel angle iron etc in required sizes with drilling of holes upto good finish for top channel, bracing and special type bracket etc. as per RESPO schedule and local approved drawing.

Excavation of earth for stay pit of size 0.6x0.6x1.2 mtr in all types of soil including proper dressing of sides and ramming of bottom including getting out the excavated soil and disposal of surplus excavated soil as directed complete work.

Fixing, tightening and nozzling of stay with pole and stay rod on required tension as per drawing /manual in LT line

Fixing, tightening and nozzling of stay with pole and stay rod on required tension as per drawing/manual in 11 KV line

Fixing, tightening and nozzling of stay with pole and stay rod on required tension as per drawing/ manual in 33 KV line

Grouting of Stay in size 0.6x0.6x0.3 in CC ratio 1:4:8 (1 cement : 4 graded stone 20mm nominal size : 8 coarse sand ) block including cost of Cement, sand and stone ballast back filling of soil and boulders in pit and ramming and proper alignment, leveling as per RESSPO Manual.

Excavation of earth for pole pit of size 0.9x0.6x1/6 of full length of pole for erection of pole in all types of soil including proper dressing of sides and ramming of bottom including etting out the excavated soil and disposal of surplus excavated soil as directed complete work

Erection of SP-33 single support pole in proper level and alignment along with fixing of all accessories like top channel & clamps as per RESPO manual

Erection of SP-55 single support pole in proper level and alignment along with fixing of all accessories like top channel & clamps as per RESPO manual

Erection of Sp-55 double support pole in proper level and alignment along with fixing of all accessories like top channel, X bracings & clamps as per RESPO manual.

Erection of SP-72(11KV/33 KV)four pole support pole in proper level and alignment along with fixing of all accessories like top channel, X bracings & clamps as per RESPO manual.

Grouting of pole in size 0.45x0.45x1/9 of the support in CC ratio 1:4:8 (1 cement:4 graded stone20 mm niminal size: 8 coarse sand) block including cost of cement, sand and stone ballast back filling of soil and boulders in pit and ramming and proper alignment, levelling as per RESPO cnstruction manual

Muffing of poles size 0.45x0.60 cm radius with 1:3:6 (1 cement:3 coarse sand :graded stone 10 mm nominal size) block size 45 cm height from ground level including cost of cement,stone and sand etc

Dismantling of existing LT/HT line. including disc fitting, Insulator, clamps, Nut & Bolts and consumer connections and Street light connections etc. including rolling of conductor and cartage back from site to JE store (PCC Single Pole).

Dismantling of existing LT/HT line. including disc fitting, Insulator, clamps, Nut & Bolts and consumer connections and Street light connections etc. including rolling of conductor and cartage back from site to JE store(SP-33 Single Pole).

Dismantling of existing LT/HT line. including disc fitting, Insulator, clamps, Nut & Bolts and consumer connections and Street light connections etc. including rolling of conductor and cartage back from site to JE store(SP-55 Single Pole).

Dismantling of existing LT/HT line. including disc fitting, Insulator, clamps, Nut & Bolts and consumer connections and Street light connections etc. including rolling of conductor and cartage back from site to JE store(PCC Double Pole)

Dismantling of existing LT/HT line. including disc fitting, Insulator, clamps, Nut & Bolts and consumer connections and Street light connections etc. including rolling of conductor and cartage back from site to JE store(SP-55 Double Pole)

Dismantling of existing LT/HT line. including disc fitting, Insulator, clamps, Nut & Bolts and consumer connections and Street light connections etc. including rolling of conductor and cartage back from site to JE store(SP-55 four Pole)

Dismantling of existing HT line. including disc fitting, Insulator, clamps, Nut & Bolts and consumer connections and Street light connections etc. including rolling of conductor and cartage back from site to JE store(ACSR Rabbit).

Dismantling of existing LT line. including disc fitting, Insulator, clamps, Nut & Bolts and consumer connections and Street light connections etc. including rolling of conductor and cartage back from site to JE store(ACSR Weasel)

Dismantling of existing LT line. including disc fitting, Insulator, clamps, Nut & Bolts and consumer connections and Street light connections etc. including rolling of conductor and cartage back from site to JE store(ACSR Dog)

Dismantling of Transformers from double pole /plinth including opening of all connections, circuts & earthing strip etc. (25 KVA).

Dismantling of Transformers from double pole/plinth including opening of all connections, circuts & earthing strip etc. (400 KVA).

Painting of SP-33 pole with angle and channel and all steel part by one coat of Red Oxide Primer and two coats of aluminium Paint and two strip of fluorescent altemate Red and White paint 30 Cm wide upto 1.5 Mtrs. From ground level.

Painting of SP-55 pole with angle and channel and all steel part by one coat of Red Oxide Primer and two coats of aluminium Paint and two strip of fluorescent altemate Red and White paint 30 Cm wide upto 1.5 Mtrs. From ground level.

Painting of SP-72 pole with angle and channel and all steel part by one coat of Red Oxide Primer and two coats of aluminium Paint and two strip of fluorescent altemate Red and White paint 30 Cm wide upto 1.5 Mtrs. From ground level.

Laying of LT service Cable From Pole to consumer end meter alongwith supporting GI wire.

Excavation of earth of size 2.1x2.1x1.2 meter for DTR Plinth.

Cement concreting work in ratio 1:4:8 for DTR Plinth.

Brick work in 1:4 ratio for DTR Plinth.

RCC Work of 1:2:4 ratio 15 cm thickness for DTR Plinth.

Cement Plaster on side walls in 1:4 ratio on DTR Plinth.

Erection, providing and fixing of wire mesh of size 50x35 mm around plinth and toe wall duly welded with frame of M.S angle iron 35 x35x6 mm and strip of size 35x6 mm in mid of each side along with wire mesh (width of wire mesh 1.5 meter ) with the height of 0.5 meter above the plinth and 2 meter above the toe wall with 1 No. gate and locking arrangment in the toe wall size including grouting of 6 Nos. legs in the ratio in block of size 0.25x0.25x0.45 meter including gravlling of shingle of size 20 to 40 mm and complete painting of wire mesh with aluminium paint with two coat (Including the cost of cement and all material).

Installation/mounting of new 25 KVA Tranformer on pole structure and fixing of channel /angle etc. and making all connections of HT and LT side and its complete commissioning.

Installation/mounting of new 400 KVA/500 KVA Tranformer on plinth structure and fixing of channel / angle etc. and making all conn ections of Ht and LT side and its complete commissioning.

Laying, Spreading, Stringing and sagging of 11 KV / 33 KV line in 3 phase (3 Phase 3 wire) of ACSR Rabbit as phase wire with G.I. earth wire complete including fixing of all accessories in 3 Nos. conductor in parallel with binding and jumpering as per profile and profile and sagging chart.

Laying, Spreading, Stringing and sagging of L.T. Lines of ACSR Rabbit as phase wire(1 phase 2 wire) with G.I. earth wire complete with binding and jumpering as per RESSPO Specn.

Laying, Spreading, Stringing and sagging of L.T. Lines of ACSR Dog as phase wire(3 phase 4 wire) with G.I. earth wire complete with binding and jumpering as per RESSPO Specn.

Making of section pole for existing LT/HT/33KV line complete in all respect.

Cartage of ST pole SP-33 Poles from store centre to construction site with loading, unloading at both points and proper stacking.(Distance 21-50 Km)

Cartage of ST pole SP-55 Poles from store centre to construction site with loading, unloading at both points and proper stacking.(Distance 21-50 Km)

Cartage of ST pole SP-72 Poles from store centre to construction site with loading, unloading at both points and proper stacking.(Distance 21-50 Km)

Cartage of other material (other than poles) by vehicle from Store Center to nearest construction site Store including loading and unloading at both ends(distance 21-50 Km)

Headload cartage of ST Pole SP-33 from road to site (distance 0-1 Km)

Headload cartage of ST Pole SP-55 from road to site (distance 0-1 Km)

Headload cartage of ST Pole SP-72 from road to site (distance 0-1 Km)

Head load cartage of small material (distance 0-1 Km)

Dismantling of Fencing and Gate of S/S including fabrication cutting and welding works at 33/11 KV Sub Station.

Laying Sagging of LT XLPE AB CABLE 3X95+1X70 Sq.mm as per direction of Engineer in Charge.

Digging of Pit through Hammer at CC, DAMAR Road.

Disconnection & Reconnection of Consumer.

Rectification, replacement and rejumpering of jumpers on LT/HT pole supports.

Laying of 4x10 Sq.MM. LT PVC Cable.

Back Carriage of Scrap material.

Annexure-B (SUPPLY ITEMS) (As per UPCL Specifications)

Supply of MS NUT & BOLT off size.

Supply of F Clamp

Supply of M.S. Holding Clamps

Supply of LT Clamp with N&B ST Pole SP-55

Supply of Stay Clamp with N&B for SP-55

Supply of PG Clamp ALU ALLOY for Dog to Dog.

Supply of LT Clamp with N&B ST Pole SP-33

Supply of Suspension Clamp

Supply of Half Clamps for fixing of Fuse set.

Supply of Double Pole Clamps with N/B for SP-55

Supply of Dead End Clamp with I Hook

Supply of Shackle Insulator 75x90 mm with Nut and Bolt

Supply of Piercing Connector for 120-95 Sq.mm

Supply of SMC Three Phase L.T. Distribution Box with inbuilt panal lock, Al bus bar RYB 25x6mm., Al Busbar N. 40x6mm. for connection of L.T. consumer (Sintex make or other ISI mark reputed company ) with Panel Lock with key)

Supply of Piercing Connector 120 to 35 Sq.mm

Supply of AL Crimping Type Lugs 400 SQ.MM.

Supply of Aluminium Lug 25 Sq.mm

Supply of MS Half Clamp for LT Distribution Box.

Supply of Ace Chemrod DIA60MM length 3000MM

Supply of Fluid Compound for Chemical Earthing Rod.

Please Enable Macros to View BoQ information