REPAIRS/REPLACEMENT OF INTERNAL WATER SUPPLY, PLUMBING, SANITARY FITTINGS, FLOORING/WALL PLASTERING, JOINERY, ROOFING, WALL PANELLING AND SCANTLING FOR RR AT PATTAN UNDER AGE (I) CIF (K).

Amount

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified.

Demolition of cement concrete in ground floors and paving not exceeding 15cm thickness (below or above ground level) un-reinforced, complete all as specified.

75 mm thick cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection laid in alternate bays (n exc 2 Sqm each) and finished even and fair without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight, complete, all as specified and directed.

75 mm thick plain cement concrete 1:4:8, type D-2 ( using 40mm graded crushed stone aggregate) as in sub base of floor, etc finished even and fair without using extra cement ,complete all as specified.

25 mm thick plain cement concrete 1:2:4 , type B-1 (using 20 mm graded crushe stone aggregate) as in floor to receive the tiles/floor finishes rough finished complete all as specified.

Non-skid coloured ceramic tiles (square/rectengular) 7 to 8 mm thick, area of each tile exc 0.18 sqm but not exc 0.38 sqm as in flooring, set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match shade of tile, laid over and including 15mm thick screed bedding layer in cement mortar 1:4 complete, all as specified. complete all as specified. Note: Colour and shade of tiles shall be approved by GE and contractor shall not have any claim whatsoever on this account.

Non-skid coloured ceramic tiles (square/rectengular) 7 to 8 mm thick, area of each tile exc 0.11 sqm but not exc 0.18 sqm as in flooring, set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match shade of tile, laid over and including 15mm thick screed bedding layer in cement mortar 1:4 complete, all as specified. complete all as specified. Note: Colour and shade of tiles shall be approved by GE and contractor shall not have any claim whatsoever on this account.

Glazed ceramic tiles, coloured, of size 350mm x 250mm/450 mm x 350mm, thickness not less than 7mm as in vertical surfaces such as skirting/dado etc, set and jointed in neat cement slurry and pointed with white cement mixed with pigment to match the shade of tile, fixed over and including 10mm thick bedding layer in cement mortar 1:3 complete all as specified. Note: Colour and shade of tiles shall be approved by GE and contractor shall not have any claim whatsoever on this account.

Chequered cement concrete tiles, machine pressed, factory made of size 20cm x 20cm, 25mm thick, with grey cement and no pigment, set, jointed and pointed in neat cement slurry, laid in floors, over and including 20mm thick screed layer in cement mortar 1:6, complete all as specified.

Dismantling of water tanks of capacity exc 250 & but n exc 500 litres, complete all as specified.

Dismantling of water tanks of capacity exc 500 & but n exc 1000 litres, complete all as specified.

Rotational moulded polyethylene water storage tanks of capacity 500 ltrs three layered (Cylindrical vertical with closed top) hoisted and fixed in position including wash out with plug/over flow pipe and anti mosquito rose coupling at one end all as specified in SSR Pt-I complete all as specified and as directed by Engr-in-Charge.

Rotational moulded polyethylene water storage tanks of capacity 1000 ltrs three layered (Cylindrical vertical with closed top) hoisted and fixed in position including wash out with plug/over flow pipe and anti mosquito rose coupling at one end all as specified in SSR Pt-I complete all as specified and as directed by Engr-in-Charge.

S&F in repairs ball valves 20mm size high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe complete all as specified.(Minimum weight 20mm - 210 gms)

S&F in repairs ball valves 15mm size high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe complete all as specified.(Minimum weight 15mm - 142 gms)

Vitreous China, wash hand basin, flat back white of size 550mm x 400mm including brackets, brass CP waste coupling 32mm dia with long screwed shank and fly nuts, 32mm dia PVC waste pipe, chain and plug, porcelain stopper including cutting for and pinning in ends of brackets or erecting stand, fixed in repairs, complete all as specified.

Vitreous China wash down water closet (Pedestal pattern), white with ‘P’ or ‘S’ trap, fixing with screws of suitable size, plastic seat cover, white closed pattern with flat bottom and cover, complete all as specified, making connections to trap and to flush pipe, fixing flushing cistern etc. and making good to floors, fixed in repairs, complete all as specified.

S&F in repairs PVC valveless, syphonic action type, flushing cistern of 10 ltrs capacity , low level, white, with inlet, ball valve, float and handle including brackets and flush pipe of polyethylene of low or high density of PVC, 32mm dia , complete all as specified.

S&F in repairs telephonic hand jet spray, chromium plated with brass chromium plated holder, suitable for 15 mm bore of 1.5mtr pipe, complete all as specified and as directed. Make :- Cera/Jaquar/Prayag/Marc

S&F in repairs grating square 100 mm size of PTMT (Minimum weight 100gms), complete all as specified.

S&F in repairs Cast iron floor trap with CI grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4), dia of outlet 100mm, complete all as specified.

S&F in repairs 15mm bore brass chromium plated wall mixer with telephonic shower with hot and cold water screwed down for iron pipe and fixed complete all as specified. Make :- Cera/Jaquar/Prayag/Marc

S&F in repairs PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified.`

S&F in repairs PVC connection 15mm size with PTMT nuts of length 600mm complete all as specified.`

Bib taps, 15mm bore, cast copper alloy, with crutch or butter fly handle, screwed down, screwed for iron pipe, or brass ferrule, fixed in repairs, complete all as specifed.

S&F in repairs stop valves 15mm bore concealed type chromium plated, screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repairs angle stop valve, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule and fixed for bore of pipe 15mm complete all as specified and directed.

S&F in repairs Pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down, high pressure, with or without lettered `Hot’ or `Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe of 15mm dia, complete all as specified.

S&F in repairs Brass CP wall/basin mixer for mixing hot & cold water screwed down for iron pipe and and fixed complete all as specified. Make :- Cera/Jaquar/Prayag/Marc

S&F in repairs Towel rail 600mm long of PTMT fixed with and including chromium plated brass screws and and wooden/plastic cleats (minimum weight 190 gms) fixed on walls, complete all as specified.

Bib tap standard of PTMT (PVC) any colour high pressure screwed for iron pipe (Minimum weight 15mm-90gms), fixed in repairs, complete all as specifed.

Pillar taps of PTMT (PVC) any colour high pressure screwed for iron pipe (Minimum weight 15mm-110gms), fixed in repairs, complete all as specifed.

Stop valve of PTMT (PVC) any colour high pressure screwed for iron pipe (Minimum weight 15mm-90gms), fixed in repairs, complete all as specifed.

PCC 1:7:12, type E2 (using 40mm graded crushed stone aggregates) as in filling for sunken floor, completing all as specified and as directed by Engr-in-Charge.

Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2Kg per Sqm including cleaning surfaces all as specified.

S&F in repairs PVC waste pipe suitable for 32mm bore waste coupling fitted to WHB, Urinals, complete all as specified.

S&F in repairs PVC waste pipe suitable for 32/38mm bore waste coupling fitted to stainless steel sinks, complete all as specified.

S&F in repairs Gun-metal, globe or gate valves of 20mm dia, with iron wheel head, screwed both ends for iron pipe, complete all as specified.

S&F in repairs Gun-metal, globe or gate valves of 15mm dia, with iron wheel head, screwed both ends for iron pipe, complete all as specified.

Taking up or down steel tubing and connections, 15 mm bore, including cleaning for refixing complete all as specified and directed by Engr-in-Charge.

Steel water tubing of nominal bore 15 mm, medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings( such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) complete all as specified.

Relaying/refixing after repairing/Cleaning thoroughly in old or new position obtained from above item No.41.00 including all fittings complete of size 15mm all as directed.

Taking up or down steel tubing and connections, 20 mm bore, including cleaning for refixing complete all as specified and directed by Engr-in-Charge.

Steel water tubing of nominal bore 20 mm, medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings( such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) complete all as specified.

Relaying/refixing after repairing/Cleaning thoroughly in old or new position obtained from above item No.44.00 including all fittings complete of size 20mm all as directed.

S&F in repairs health faucet ABS body with wall hook and 1 mtr SS braided rubber hose pipe complete all as specified Make:- CERA Cat Part No. F-8030102/Jaquar Cat Part No.ALD-563/Prayag Cat Part No-BEA-41

S&F in repairs Chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union complete of size 125mm all as directed.

S&F in repairs Stainless steel sink with drainage board made of stainless steel 1mm thick for kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever cast iron bracket, connecting union etc. and overall size 915 x 460mm with bowl size 410 x 330 x 160mm, complete all as specified & directed.

S&F in repairs Sink without drainage board made of stainless steel 1mm thick for kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever cast iron bracket, connecting union etc. and overall size 495 x 420mm with bowl size 410 x 330 x 160mm, complete all as specified & directed.

S&F in repairs Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminium hinging device, complete all as specified.

S&F in repairs Vitreous Chinaware squatting pan, orissa pattern size 580mm x 440mm with integral foot rests, white, with cast iron ‘P’ or ‘S’ trap, front or back inlet, including provision of lime concrete, making connections to trap and to flush pipe etc. and making good to floors, complete all as specified.

S&F in repairs Flush pipe of polyethylene of low or high density or PVC 32mm dia, for low level cistern, complete all as specified.

S&F in repairs Viterous China urinal, bowl type flat back, size 465 x 355 x 265mm white (minimum) with grating and union for discharge pipe, complete including providing and fixing plugs, beding urinal against wall in cement mortar 1:2 securing urinal plugs with and including 60mm long brass screws, pointing around urinal back in cement, 5 ltr cast iron automatic flushing cistern including bracket, flush pipe including 32mm bore PVC waste pipe, complete all as specified.

Taking down chowkat or frames with shutters (without taking off shutters from the frames) area n.exc 1.5 Sqm each including cutting holes for taking out hold fasts, dismantling brick work (holes cut and any other damages to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost) complete all as specified.

Taking down chowkat or frames with shutters (without taking off shutters from the frames) exc. 1.5 Sqm but n.exc 4 Sqm each including cutting holes for taking out hold fasts, dismantling brick work (holes cut and any other damages to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost) complete all as specified.

2nd class soft wood (Kail) plain, solid straight chowkats,and frames, wrought framed rebated on the solid, rounded or chamfered put together with glue, pinned at joints supplied and fixed complete, all as specified and as directed.

2nd class soft wood (kail), plain framed , panelled shutters (any numbers of panels), 35mm thick, with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers; supplied & fitted to chowkats, complete all as specified.

Factory made, 30 mm thick 2nd class soft wood (Kail) glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc, (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc, sizes of members of shutters as specified in SSR Part -I. section 8, clause 8.24(a) for doors etc are provided with stiles and rails, complete all as specified.

Mild steel galvanised wire cloth 0.63mm nominal dia of wire and average width of aperture 1.40mm fixed with tinned tacks, wire staples or beading etc, complete all as specified.

S&F in repairs Mild steel galvanised wire cloth 0.63mm nominal dia of wire and average width of aperture 1.40mm fixed with tinned tacks, wire staples or beading etc, complete all as specified.

Dismantling timber scantling 40 Sq cm and over in section in any position, unframed work, complete all as specified and directed by Engr-in-Charge.

2nd class soft wood (Kail) as in scantling, clean sawn timber, fixed in framed work, complete all as specified.

Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplied and fitted in openings as per specification and drawing shown in SSR Part-II, complete all as specified.

Factory made Solid PVC Moulded Door Shutter, 28 to 30 mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick moulded prelam PVC sheet on the front face & 2mm plain colour PVC sheet on the back face with particle board core, supplied & fitted in the frame at site as per specification & drawings shown in SSR Part-II, complete as specified.

Butt hinges, medium weight, cold rolled, mild steel 100 mm long (ISI marked), complete all as specified.

Butt hinges medium weight cold rolled Stainless steel, size 100 mm, complete all as specified.

Aluminium anodised, barrel tower bolt of extruded section and fixed, 200 mm long (ISI marked), complete all as specified.

Aluminium anodised, barrel tower bolt of extruded section and fixed, 100 mm long (ISI marked), complete all as specified.

Aluminium handle, cast type, anodised, 150 mm long (ISI marked), complete all as specified.

Butt hinges, medium weight, cold rolled, mild steel 75 mm long (ISI marked), complete all as specified.

Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) with and fixing clips of sheet, cast or excluded sections and fixing bolts and sliding bolts of excluded sections or cast aluminum alloy and fixed, 300 mm long, complete all as specified.

S&F in repairs 300mm ordinary rat tail rod pattern door spring including roller and roller plate of mild steel, complete all as specified.

Harrison rails (curtain rails), anodised aluminium alloy, chromium plated with fixing brackets, stops, rollers etc fixed in repair, complete all as specified.

Taking down cement plaster, of any description on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water complete all as specified.

15 mm thick rendering on fair faces of brick/concrete surfaces in cement mortar 1:4 and finished even and smooth without using extra cement complete all as specified.

Preparation of new plastered surfaces of wall and applying three coats of white wash, complete all as specified.

10 mm thick rendering on fair faces of brick /concrete surfaces in cement mortar 1:6 and finished even and smooth without using extra cement complete all as specified.

Preparation of new plastered surfaces of walls and applying two coats of oil emulsion distemper over a coat of suitable primer, complete all as specified.

2nd class soft wood (kail) as in fascia boarding, 20mm thick, clean sawn, planed one side fixed with butt joint with nails in any position (except flooring & skirting), complete all as specified & directed.

Preparation of new or previously untreated wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified.

Preparation of old painted wooden or wood based surfaces of any description over 10cm width or girth not otherwise described and applying one coat of synthetic enamel paint at any height and any place complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete, brick surrounds, glazed with putty or fixed with beads, complete all as specified.

4mm sheet glass, ordinary quality and glazing with oil putty/pins/spring pins and wooden beads in square not exceeding 0.5 Sqm in each pane complete all as specified.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering, complete all as specified.

Pre-painted galvalume aluminum zinc coating GI based corrugated profile steel sheet 0.50mm thick of colour as approved by AGE(I), having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified.

Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of colour as approved by AGE(I), having tensile strength of 550 Mpa as in roof covering/cladding to ridges, valley gutters etc. fixed with self tapping screws complete all as specified.

Dismantling wall and ceiling board (fibre, pulp, insulation etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets, complete all as specified.

Veneered decorative plywood , grade 1 ( with BWR resin ) with decorative face veneers on both face, 6mm thick as in ceiling, lining; fixed with nails to timber frame work complete all as specified.

Dismantling of CI/PVC pipes, jointed in cement mortar and taking out of trenches or in floor or wall 100/75mm bore, complete all as specified.

PVC (SWR) pipes, 110mm dia, single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified & directed.

PVC (SWR) pipes, 75mm dia, single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified & directed.

PVC (SWR) pipes, 110mm dia, single socketed, in any length with rubber ring joints, fixed to walls, complete all as specified & directed.

PVC (SWR) pipes, 75mm dia, single socketed, in any length with rubber ring joints, fixed to walls, complete all as specified & directed.

110mm size PVC (SWR) branch pieces, single Y/bends/Tee ( equal or unequal), complete all as specified.

75mm size PVC (SWR) branch pieces, single Y/bends/Tee ( equal or unequal), complete all as specified.

Demolition of brickwork and stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc., but excluding ashlar facings, dressed stonework and precast concrete articles complete including removing of rubish all as specified and directed by Engineer-in-Charge.

Brick work with subclass 'B' bricks, straight or curved on plan exc 6 m mean radius, built in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

Stone walling of random rubble with best quality locally available harder stone such as granite, trap or basalt, uncoursed, well bonded, bedded, solidly hearted and built in cement mortar 1:6, complete all as specified & directed.

Dismantling boarding of any description, fixed in any position with nails including cover fillets, complete all as specified.

2nd class soft wood (kail) as in weather boarding, clean sawn, plain 20mm thick or feather edged 15mm to 20mm thick and fixed with 30mm laps, complete all as specified & directed.

Preparation of new plastered surfaces of walls and applying two coats of colour wash over a coat of white wash, complete all as specified.

Toilet paper holder box type complete all as specified. Note:- Credit schedule has been given separately under tender documents and shall be adjusted in general summary by the deptt. for arriving at net contract sum.

M/S N A Enterprises

M/S FAYAZ AHMAD BHAT

M/S RATHER STEEL WORKS