SPECIAL REPAIR TO ROOF AND JOINERIES OF BOATS WANE STORE BLDG NO P 87 CPO MCPO BAR BLDG NO P 88 PO S BAR BLDG NO P 89 AND REGIMENTAL SHOP AT INS GARUDA NAVAL BASE KOCHI

Amount

Demolition of Cement Concrete of any description and in any position not otherwise specifically provided for, complete all as specified and as directed by Engineer in Charge.

M&L for Hard core of Gauge exceeding 63mm but not exceeding 150mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rolled/ rammed to a true surface, complete all as specified and as directed by Engineer in Charge.

M&L for 75 mm thick Plain Cement Concrete 1:3:6, Type C-1, (20mm graded stone aggregate) as in plinth protection and finished the surface even and fair without using extra cement, complete all as specified and directed.

Dismantling timber scantlings 40 Sq. cm and over in section, in any position complete all as specified and as directed.

M&L for second class hard wood scantling, clean sawn, 40 Sq. cm and over in section, in framed work, complete all as specified and as directed.

Dismantling timber framed work scantlings under 40 Sq. cm in section, in fillets, rails, posts, rafters, purlins etc., complete all as specified and as directed.

M&L for second class hard wood plain fillets, square, rectangular, any section, clean sawn, secured with nails or brads, sectional area exceeding 6 Sq. cm and not exceeding 13 Sq. cm, complete all as specified and as directed.

M&L for second class hard wood plain fillets, square, rectangular, any section, clean sawn, secured with nails or brads, sectional area exceeding 13 Sq. cm and not exceeding 25 Sq cm, complete all as specified and as directed.

M&L for preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with creosote complete all as specified and as directed.

Dismantling boarding of any description, fixed in any position with nails, complete all as specified and as directed.

M&L for 4mm thick ACP sheet as in ceiling and eaves board, including cutting and fixing with screw and 40x40x2mm MS Tubes, complete all as specified and as directed .

Dismantling single layer Mangalore pattern or similar tiles in roofing complete all as specified and as directed.

Dismantling tile battens of any size including tiling fillets spaced exceeding 15 cm centre to centre complete all as specified and as directed.

S&F second class hard wood clean swan battens for tiles, fixed at 30 cm centre to centre, Sectional area exceeding 5 Sq. cm and not exceeding 15 Sq. cm complete all as specified and as directed.

All as per Item No. 14 herein above, but fixing only battens complete all as specified and as directed. Note :- Battens obtained from dismantling vide item no. 13 shall be used

M&L for preparing surface of tiles or slate battens, any size and spacing, prepared and treated all over with creosote complete all as specified and as directed.

Dismantling of plain or corrugated steel sheeting, any gauge and thickness, including nainital or similar pattern roof covering, complete all as specified and as directed.

S&F 0.71 mm thick, aluminium sheeting, alloy 31000 H4, in ridge, hip, valley gutter, drip and straight flashing (length and girth as fixed), complete all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet, 0.50mm thick of any colour, having tensile strength of 550MPa as in roof covering/ cladding to wall, fixed with self tapping screws, complete all as specified and as directed.

S&F Pre-painted Plain sheet, 0.50mm thick of any colour, having tensile strength of 550MPa, as in roof covering/ cladding, fixed with screws, all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, all as specified.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and as directed by Engineer in Charge.

M&L for preparation of new steel surfaces of any description upto a height of 15 metres, over 10 cm in width or girth not otherwise described and applying two coats of epoxy coated paint over one coat of epoxy primer, complete all as specified and directed.

Excavation in post holes (or similar holes) each n.exe 0.5 cum, getting out returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exc 25 cm watering in soft/loose soil all as specified and as directed by Engr-in-Charge.

M & L Cement concrete in post holes foundation fillings and mass concreting PCC1:3:6 type C2 using 40mm graded stone aggregate complete all as specified and as directed by Engr-in-Charge.

Removing excavated material to a diatance n.exc 0.5Km and depositing where directed at a level n.exc 1.5m above starting point and making good surface in soft/loose soil all as specified and as directed by Engr-in-Charge.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or re-fixing or removal to store complete all as specified and as directed. Note : Measured overall as fixed along the centre line over fittings and accessories.

S&F EURO GUARD PRO Square UPVC Rainwater Gutter (220 mm), with all necessary fittings, clamp, joints, end cap, corner drop, centre drop, etc., joining compounds, nut, bolts or screws etc., and fixing in position, at any height, complete all as specified and as directed.

S&F 110 mm bore PVC (SWR) Pipes, single socketed in any length with rubber ring joints, fixed to walls complete all as specified and as directed. Note : Jointing shall be done with solvent cement.

S&F 110mm bore PVC (SWR) bends, any radius, complete all as specified and as directed.

Supply only integral Water Proofing Compound, complete all as specified and as directed by Engineer in Charge.

M&L for preparation of old steel surfaces of any description upto a height of 15 metres, over 10 cm in width or girth not otherwise described and applying one coat of epoxy coated paint complete all as specified and directed.

M&L for preparation of newly plastered surfaces and applying two coats of two coats of weather proof (antifungal) paint over a coat of primer over and incl 3mm thick exterior wall care putty complete all as specified and as directed.

M&L for Complete removal of existing treatment of external wall using water jet, mechanical grinders including rubbing, washing down with water, etc and applying two coats of weather proof (antifungal) paint over a coat of suitable primer over and incl 3mm thick exterior wall care putty complete all as specified and as directed by the Engineer-In-Charge. Note for item no. 33 & 34:- Application of paint , primer and putty shall be as per manufacturer's instruction. The quoted rate shall include cost of scaffolding as required.

Taking down chowkats with shutters (without taking off shutters from the frame) not exceeding 1.5 Sqm, complete all as specified and directed.

Taking down chowkats with shutters (without taking off shutters from the frame) exceeding 1.5 Sqm, but not exceeding 4 Sqm, complete all as specified and directed.

Taking down shutters of any description, area not exceeding 1 Sqm each, complete all as specified and directed.

All as per Item No. 37 here in before, but exceeding 1.00 Sqm and not exceeding 2.00 Sqm, complete all as specified and directed.

Taking down shutter of any description not exceeding 1.00 Sqm including re-securing or easing and adjusting and re-fixing in same opening, complete all as specified and directed.

Taking down shutter of any description exceeding 1.00 Sqm and not exceeding 2.0 Sqm including re-securing or easing and adjusting and re-fixing in same opening, complete all as specified and directed.

Supply and fixing 2nd class hard wood, plain, solid, straight chowkat and frames, wrought framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified.

Supply and fixing 2nd class hard wood, 30mm thick, glazed, gauged and skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, gauze etc., size of members of shutters as specified in SSR Part I, Section 8, clause 8.24(a), complete all as specified and directed.

All as per Item No. 42 here in before, but divided into square with sash bars, any numbers, complete all as specified and directed.

Supply and fixing 2nd class hard wood, 35mm thick, panelled shutter, plain, framed, panelled (any member of panels) with panels of timber flat on both sides (feather edged) or veneered particle board medium density, wood particle board with commercial face veneers, complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing, complete all as specified and directed.

S&F Factory made Solid Panel PVC door shutters, both sides using Prelaminated PVC sheet, 30 mm thick (Style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of both side Prelaminated colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing, complete all as specified and directed.

Supply and fixing 200 mm long aluminium anodised barrel tower bolt of extruded section, complete all as specified and directed.

Supply and fixed in repairs, 200 mm long aluminium anodised barrel tower bolt of extruded section, complete all as specified and directed.

Supply and fixing 150mm long aluminium anodised barrel tower bolt of extruded section, complete all as specified and directed.

Supply and fixed in repairs, 150mm long aluminium anodised barrel tower bolt of extruded section, complete all as specified and directed.

Supply and fixed in repairs, 100mm long aluminium anodised barrel tower bolt of extruded section, complete all as specified and directed.

Supply and fixing 300mm long aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy, complete all as specified and directed.

All as per Item No 52 here in before, but fixed in repairs, complete all as specified and directed.

Supply and fixing 100mm size Stainless Steel butt hinges, medium weight, complete all as specified and directed.

Supply and fixing 150 mm size extruded, anodised aluminium alloy handles, fabricated type, complete all as specified and directed.

All as per Item No. 55 here in before, but fixed in repairs, complete all as specified and directed.

Supply and fixing, aluminium plate Type II, gate and shutter hook and eye of 200mm size, complete all as specified and directed.

Supply and fixing, in repair aluminium plate Type II, gate and shutter hook and eye of 200mm size, complete all as specified and directed.

Supply and fixed in repairs, aluminium alloy body door stopper and tongue anodised with hard drawn steel spring in floor, 140mm over length of cover plates, complete all as specified and directed.

Supply and fixing aluminium alloy wire cloth, 0.45 mm nominal dia. of wire and average width of aperture 1.40 mm and fixed with aluminium wire staples, complete all as specified and directed.

All as per Item No. 60 here in before, but fixed in repair, complete all as specified and directed.

S&F Sheet glass ordinary quality, 3.00 mm thick and glazing with oil putty/ beads in squares not exceeding 0.5 Sqm in each pane, complete all as specified and directed.

Supply and fixing 4.00mm thick frosted glass, pin head type and glazing with oil putty/ beads in squares not exceeding 0.5 Sqm in each pane, complete all as specified and directed.

S&F in repairs, aluminium (extruded section) Door Closer, hydraulically regulated, Designation No.3 Universal Type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg and fixed with stainless steel screw, complete all as specified and directed.

Taking down cement plaster on Brick/ Concrete wall and ceilings, including racking out joints, hacking for key, scrubbing down with water complete all as specified and as directed by Engineer in Charge.

M&L for cement plaster in two coats, 8 mm thick in cement mortar 1:4 using WPC over 12mm thick in cement mortar 1:6 on external surfaces, finished even & smooth without using extra cement all as specified and directed. Note : WPC shall be measured and paid separately.

M&L for 10mm thick rendering on brick or concrete wall surfaces in cement mortar 1:6, finished even and smooth without using extra cement, complete all as specified and as directed by Engineer in Charge.

M&L preparation of new plastered surfaces of wall (plastered or un-plastered) including cornices and applying two coats of distemper oil emulsion over a coat of primer, over 3mm thick wall care putty complete all as specified and as directed by Engineer in Charge.

S&F for Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixing with dash fasteners of required dia. and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, complete all as per architectural drawings & specifications and as directed by Engineer in Charge.

S&F for anodized aluminium sliding window and ventilator frame without sash bar, including 4mm thick plain sheet glass and including all necessary jointing cleats hold fasts rubber gasket, anodised snap beading, anodized aluminium fittings such as "F" channel if required for wire mesh or aluminium grill, aluminium handle locking arrangement etc. based on Hindalco catalogue no. 1. 4095 - 61.98x29.70x1.60mm = 2 track 2. 9777- 39.00x20.00x1.60mm = Shutter vertical 3. 3994 - 41.00x20.00x1.20mm = shutter top and bottom 4. 9778 - 39.00x20.00x1.50mm = Shutter vertical inter lock complete all as specified and as directed

S&F Aluminium powder coated sliding type window with 4mm thick plain sheet glass including provision of airtight heading and handling arrangements complete with using following sections : (i) Outer Frame 50.80x25.40x1.5mm (ii) 3 Track Frame 43.66x22x1.22mm (iii) Shutter Frame 31.80x14.50x1.20mm (iv) Shutter Interlock 31.80x20.50x1.20mm

S&F powder coated anodised aluminium window and ventilator shutter powder coated side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1no.) complete all as specified

S&F aluminium anodised powder coated frame work for door with out sash bar, including all necessary jointing cleats, hold fasts, hinges with fixing clips, rubber gasket, anodised snap beading, anodised aluminium fittings, locking arrangement etc. (minimum thickness of powder coating 50 micron), Section used for door as per Catalogue No. 9258 of size 50mmx44.50mmx1.80mm door vertical stiles, Catalogue No. 9286 of size 50mmx45mmx1.50mm door Top and middle/ lock rail, Catalogue No. 9246 of size 100mmx44.50mmx1.85mm door bottom rail, of Hindalco or equivalent make as approved by GE, complete all as specified and as directed.

S&F 9 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work, complete all as specified and as directed.

M&L for 5 mm thick sheet glass, ordinary quality fixed with glazing clips/aluminium cleats in square not exceeding 0.50 Sqm in each pane complete all as specified and as directed.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.

S&F aluminium anodised grill, having mesh size 50mm x 50mm made out of 6 mm wide 3 mm thick aluminium section including 'U' clips and all necessary fixing arrangements, complete all as specified and as directed .

Demolition of brick work or stone, boulder, precast PCC block masonry including all quoins, arches, pillar etc. built in cement mortar or cement lime mortar complete all as specified and directed.

M&L for Precast cement concrete block masonry with solid blocks, Type C-1, 1:3:6 (using 20mm graded stone aggregate) exceeding 10 cm in width and setting in Cement Mortar 1:6, complete all as specified and as directed.

MS BUILDERS

JKM CONSTRUCTIONS

Albert Rebello and Company

REIGN CONSTRUCTIONS