CO 2 Nos Tube well to cover the tail end area of BVMIP Zone No 1 and Improvement of FIS Malwana in GP Badhyal Tehsil Balh Distt Mandi HP

Amount

Excavation in foundation, trenches (for pipes & pits) upto all depths in all classification of earth work such as pick work, jumper work, saturated soil including bailing and pumping out water, blasting soft/ hard rock or chieselling soft/hard rock where blasting is prohibited in all lifts including trimming and dressing of sides, leveling of beds to correct grade i/c shoring /strutting , planking, timbering & dewatering wherever required, stacking the useable & unuseable material /soil separately & after laying jointing & testing of pipes, returning the useable soil in trenches in 15 cm layers including consolidating of such deposoited layer by ramming & watering & then disposing of all surplus excavated soil /unusable material as directed with in all leads & lifts including restoration unmetalled surfaces to its original condition & including cost of diversion for traffic, night signals, fixing caution boards, crossing over trenches for access to houses, fencing etc. complete in all respect with in all leads & lifts as per direction of Engineer-in-Charge.

Providing & laying cement concrete 1:4:8 (1 cement : 4 sand: 8 graded stone aggregate 40 mm nominal size) and curing complete excluding cost of form work in foundation and plinth including carriage of material with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Providing form work with steel plates 3.15 mm thick welded with angles iron in frame 30 x 30 x 5 mm so as to give a fair finish including centering shuttering struting and propping etc. with wooden battens and ballies height of propping and centering below supporting floor to ceiling not exceeding 4 meters and removal of the same for in-situ- reinforced concrete and plain concrete in:-

Vertical surface such as wall (any thickness) partition and the like including attached pillasters, butresses, etc. plinth and string course complete job in all respects with in all leads and lifts as per the direction and best satisfaction of Engineer-in-Charge.

Providing and laying cement concrete 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 20 mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in:-

Foundation, footing & bases of columns and the like mass concrete complete in all respect with in all leads and lifts as per the entire satisfaction & directions of Engineer-in-Charge.

Providing Mild Steel/Tor Steel reinforcement for R.C.C work including bending, binding and placing in position complete up to floor two level complete in all respect within all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Laying, jointing, testing and carriage of GMS (M) Pipe of following diameters confirming to BIS 1239 (Part-1) of following grade specified below (Latest with upto date ammendments) and having wall thickness as specified below with bevelled ends and capable of withstanding required test pressure in random length of 4 to 7 meters, including manufacturing reducers, tapers, all short pieces, bends etc. as per site requirement made from parent tube. Providing and welding of MS flanges detailed as below. The MS flanges shall confirm to BIS 6392-1971 (with latest up to date ammendments) duly welded in two layers (two inner and two outer) with pipes at both ends as per relevant BIS standards along with nuts and bolts of required sizes, 3mm thick compressed asbestos fiber/synthetic rubber gaskets confirming to relevant BIS standards. The laying of pipe will include all operation such as cutting, welding, jointing, providing & fixing of MS flanges, fabrication of bends, tees etc. including lowering and laying in excavated trenches to ensure required level including flushing, cleaning and hydraulic testing complete in all respect to the satisfaction of the Engineer-in-Charge. The fabricated bends shall have three or four cuts having its radius not less than five times the dia of pipe. The welding electrodes shall be as per IS 814 of Advani Oerlikon/ L&T or ISI marked make. The rates also includes entire carriage of material, flushing, cleaning & hydraulic testing complete to the best satisfaction & direction of Engineer-in-Charge with in all leads and lifts. (Earth work in trenches will be measured and paid for separately).

Phase-1st Malwana:- 150 mm dia-GMS Pipe 4.80 mm thickness with F.T.-28

Phase-1st Malwana:- 150 mm dia-GMS Pipe 4.80 mm thickness with F.T.-17

Phase-1st Malwana:- 150 mm dia-GMS Pipe 4.80 mm thickness with F.T.-5

Phase-2nd Tikkar:- 150 mm dia-GMS Pipe 4.80 mm thickness with F.T.-28

Phase-2nd Tikkar:- 150 mm dia-GMS Pipe 4.80 mm thickness with F.T.-17

Phase-2nd Tikkar :- 150 mm dia-GMS Pipe 4.80 mm thickness with F.T.-5

Laying, jointing (by way of circumfrential butt welded joints by electrical arc welding) testing and carriage of GMS (M) pipe of following diameters confirming to BIS 1239 (Part-I), steel grade specified below (latest with upto date ammendments) having wall thickness as specified below with bevelled ends and capable of withstanding required test pressure in a random length of 4 to 7 meters, including manufacturing reducers/ tapers, all short pieces, beds etc. as per site requirement made from parent tubes. The laying of pipe will include all operation such as cutting, welding, jointing, fabrication of bends, tees etc. including lowering and laying in excavated trenches to ensure required level including flushing, cleaning and hydraulic testing complete in all respect to the satisfaction of the Engineer-in-Charge. The fabricated bends shall have three or four cuts having its radius not less than five times the dia of pipe. The pipes shall be factory galvanized (zinc coating both inside and outside) as per relevant IS standards. The welding electrodes shall be as per IS 814 of Advani Oerlikon/ L&T or ISI marked make. The rates also includes entire carriage of material, flushing, cleaning & hydraulic testing complete to the best satisfaction & direction of Engineer-in-Charge with in all leads and lifts. (Earth work in trenches will be measured and paid for separately).

Phase- I & II:- 150mm dia - GMS pipe of 4.80 mm thickness

Submersible Pump Set Tube Well No.1:- Supply of submersible Raw water pump set confoming to ISO-9906 suitable to handle turbidity upto 600 PPM of KSB / Kirloskar/ Sabar/ johnston/ Crompton/ Kalama/ Grund fos make instead of clear water pump confirming to BIS 8034 for 600 PPM or latest suitable for lifting water (latest with upto date ammendments) fitted with impellers of bronze/ suitable alloy. The pump should be fittted with free flow impellers of Bronze/ suitable alloys directly coupled to squirrel cage electric induction motor of same make as (manufacturer standard) confirming to BIS 9283-1979 (latest with up to date ammendments), totally dust and water proof for submersible duty, isolated from the pump by intermidiate casing with double mechanical seal in oil chamber & grease packed lubricated bearing & provided with stainless steel thrust bearing plate to withstand vertical loads with minimum wear & tear. It should also be fitted with a device to take up expansion of water with the heating of motor. The pump set should include water level guard, errection clamps, cable clips & depth gauge etc. The pump shall be suitable for operation on data given as below:-

A) SITE CONDITIONS:- Location of site- About 15 Kms. from Nerchowk.The altitude of place in which the motor is intended to work in ordinary service if it exceeds 1000 mtrs = 784 mtrs above MSL, Detail of quality of water - clear cold water, water free from sand or not-Yes. Water corrosive or not- No.Turbidity (if any) - Clear cold water. PUMPS: BIS 1520-1980, read with BIS 9137-1978 both latest with upto date ammendments. Nos of pumps reqd.-1 No. pump. Pump operating conditions. Capacity-14.99 LPS. Total head in Mts.-157.48 Mtrs.(If total head in not known then following details be provided):Static Head- 139.00 Mtrs.Minimum depth of water-………….Mtrs.Variation in water level.-………….Mtrs.Ground level to max. water level………….Mtrs.Ground level to delivery point-…………..Mtrs.Pressure in the suction tank-…………..Kg/cm/2.Pressure in the delivery tank-…………..Kg/cm/2.Length of R/main-2260 mtrs..Dia of R/main-150 mm Dia . No. of working hours per day- 20 Hrs.

Supply, Installation, Testing and Commissioning of Star Delta Starter panel for submersible pump made out of 16 Gauge sheet, powder coated dust and vermin proof, wall/base mounted and front opening door type with copper insulated wiring suitable to operate 1 No. pump of the rating 65 HP through Star Delta Starter mechanism. Starter should be capable enough to handle the following faults like short circuit, over current, under current, over voltage, under voltage, dry run protection and phase loss with LED ON/OFF & TRIP indicators Of reputated make i.e JSV Approved / Globle Product complete in all respect as per the entire satisfaction of Engineer-in-Charge.

Star, Delta and Mains Power Contactors of required ratings as per type-2 co-ordination for 65 HP starter complete in all respect as per the entire satisfaction of Engineer-in-Charge.

Voltage Protection device to protect panel from over voltage and under voltage complete in all respect as per the entire satisfaction of Engineer-in-Charge.

Single phasing and phase reversal protection device to safeguard system from single phasing and phase reversal of the supply voltage complete in all respect as per the entire satisfaction of Engineer-in-Charge.

Multi function meter indicating different parameters like Current, Voltage, KWH, PF, THD etc. with RS 485 communication Make:- JSV Approved / Globle Product complete in all respect as per the entire satisfaction of Engineer-in-Charge.

Main incomer MCCB/MCB of suitable capacity of L&T / Schnieder/ABB make on the feeder for pumping set confirming to BIS 2516-1985 (Latest edition) complete in all respect as per the entire satisfaction of Engineer-in-Charge.

Individual Starter incomer MCCB/MCB of suitable capacity of L&T / Schnieder/ABB make on the feeder for pumping set confirming to BIS 2516-1985 (Latest edition) complete in all respect as per the entire satisfaction of Engineer-in-Charge.

Three phase indicating lamps complete with logged switches for individual motors conforming to BIS 3452 (Part I & II) latest with upto date ammendments complete in all respect as per the entire satisfaction of Engineer-in-Charge.

LED On / Off & Trip indicator and push buttons, Control and power wiring, Power capacitor, Cooling fan 230 VAC, Contorl terminal, Bus Bar, i.e.Bolt, insulator etc. complete in all respect as per the entire satisfaction of Engineer-in-Charge.

Surge supressor device with Isolating MCCB to eliminate the power surges due to lightening and system surges complete in all respect as per the entire satisfaction of Engineer-in-Charge.

Control Transformer to provide a stable control volatge to safegaurd the control circuit of all the components from the voltage surges and spikes complete in all respect as per the entire satisfaction of Engineer-in-Charge.

Independent Control Panel with Switch Fuse Unit and Fuses of Suitable Amperage to eliminate the KItKat fuses of HPSEB Of reputated make i.e JSV Approved / Globle Product complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Providing double flanged cast steel sluice valve, ASA-150 of Leader/BHEL/ Kirlosker/Kilburn make and one step higher then delivery line of pump and capable of withstanding normal seat pressure as per BIS standards with upto date ammendments) complete in all respect as per the entire satisfaction of Engineer-in-Charge.

Providing double flanged cast steel reflux valves class, ASA-150 of Leader/BHEL/ Kirlosker/Kartar/Kilburn make for rising main and capable of withstanding normal seat pressure as per BIS standards with upto date ammendments) complete in all respect as per the entire satisfaction of Engineer-in-Charge.

Providing 100mm dia circular dial analog pressure gauge of suitable range of Fiebig /Bourden/ PREGA/precision make complete with all accessories such as stop cock, copper tubing etc.as per IS: 3624-1987 with upto date ammendments complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Providing discharge meter of standard make to be fixed on the rising main in pump house as per the directions of the Engineer in charge as per IS:2373:1981 with upto date ammendments complete in all respect as per the entire satisfaction of Engineer-in-Charge.

Installation of all the items apparing as per the schematic drawing complete in all respect as per the entire satisfaction of Engineer-in-Charge.

Providing and laying copper PVC insulated armoured power cable (One cable carrying all the three phases) of suitable size and capacity to motors and all other electircal equipments as per IS:1554 (P-I) 1988 or latest with upto date ammendments of siemens/GLOSTER /IEC/ICC/EICO/NATIONAL/GRANDLAY make including all other accessories such as thimbles, flexible pipes, solders, nuts and bolts cable glands etc. laid in pipes or trenches under floor complete in all respect as per the entire satisfaction of Engineer-in-Charge.

(a) Motor side (From switch to starter and starter to motor) complete in all respect as per the entire satisfaction of Engineer-in-Charge.

(b) Supply side (From Meter of HPSEB to bus bar and switch) complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Providing and fixing double loop earthing with GI plate 600mmx600x3mm thick electrode complete with material such thimbles nuts and charcoal and common salt, 25mmx5mm copper strips as per IS:3043:1987 with upto date ammendments for motors and other electrical equipments and digging of pits etc. complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Low Cost Automation System :- PLC (Programmable logic controller) with appropriate digital and analog inputs and outputs to give automatic command to Star Delta Starter Panel/ Energy Saving Variable Frequency Starter Panel Make: JSV Approved complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Electronic relay card 8 channel complete in all respect as per the entire satisfaction of Engineer-in-Charge.

SMPS 4.5 Amps to energise PLC system complete in all respect as per the entire satisfaction of Engineer-in-Charge.

HMI (Human Machine Interface) 7" display for Monitoring and Controlling of Centrifugal pumps Make:JSV Approved complete in all respect as per the entire satisfaction of Engineer-in-Charge.

Control MCB for Automation System complete in all respect as per the entire satisfaction of Engineer-in-Charge.

Level Sensor to indicate the water level of tank remotely complete in all respect as per the entire satisfaction of Engineer-in-Charge.

Shielded Data Cable for Communication of Level Sensor with PLC complete in all respect as per the entire satisfaction of Engineer-in-Charge.

Submersible Pump Set Tube Well No. 2:- Supply of submersible Raw water pump set confoming to ISO-9906 suitable to handle turbidity upto 600 PPM of KSB / Kirloskar/ Sabar/ johnston/ Crompton/ Kalama/ Grund fos make instead of clear water pump confirming to BIS 8034 for 600 PPM or latest suitable for lifting water (latest with upto date ammendments) fitted with impellers of bronze/ suitable alloy. The pump should be fittted with free flow impellers of Bronze/ suitable alloys directly coupled to squirrel cage electric induction motor of same make as (manufacturer standard) confirming to BIS 9283-1979 (latest with up to date ammendments), totally dust and water proof for submersible duty, isolated from the pump by intermidiate casing with double mechanical seal in oil chamber & grease packed lubricated bearing & provided with stainless steel thrust bearing plate to withstand vertical loads with minimum wear & tear. It should also be fitted with a device to take up expansion of water with the heating of motor. The pump set should include water level guard, errection clamps, cable clips & depth gauge etc. The pump shall be suitable for operation on data given as below:-

A) SITE CONDITIONS:- Location of site- About 15 Kms. from Nerchowk.The altitude of place in which the motor is intended to work in ordinary service if it exceeds 1000 mtrs = 784 mtrs above MSL, Detail of quality of water - clear cold water, water free from sand or not-Yes. Water corrosive or not- No.Turbidity (if any) - Clear cold water. PUMPS: BIS 1520-1980, read with BIS 9137-1978 both latest with upto date ammendments. Nos of pumps reqd.-1 No. pump. Pump operating conditions. Capacity-14.99 LPS. Total head in Mts.-166.30 Mtrs.(If total head in not known then following details be provided):Static Head- 144.00 Mtrs.Minimum depth of water-………….Mtrs.Variation in water level.-………….Mtrs.Ground level to max. water level………….Mtrs.Ground level to delivery point-…………..Mtrs.Pressure in the suction tank-…………..Kg/cm/2.Pressure in the delivery tank-…………..Kg/cm/2.Length of R/main-245 mtrs..Dia of R/main-150 mm Dia . No. of working hours per day- 20 Hrs.

Supply, Installation, Testing and Commissioning of Star Delta Starter panel for submersible pump made out of 16 Gauge sheet, powder coated dust and vermin proof, wall/base mounted and front opening door type with copper insulated wiring suitable to operate 1 No. pumps of the rating 75 HP through Star Delta Starter mechanism. Starter should be capable enough to handle the following faults like short circuit, over current, under current, over voltage, under voltage, dry run protection and phase loss with LED ON/OFF & TRIP indicators Of reputated make i.e JSV Approved / Globle Product complete in all respect as per the entire satisfaction of Engineer-in-Charge.

Star, Delta and Mains Power Contactors of required ratings as per type-2 co-ordination for 75 HP starter complete in all respect as per the entire satisfaction of Engineer-in-Charge.

Voltage Protection device to protect panel from over voltage and under voltage complete in all respect as per the entire satisfaction of Engineer-in-Charge.

Single phasing and phase reversal protection device to safeguard system from single phasing and phase reversal of the supply voltage complete in all respect as per the entire satisfaction of Engineer-in-Charge.

Multi function meter indicating different parameters like Current, Voltage, KWH, PF, THD etc. with RS 485 communication Make:- JSV Approved / Globle Product complete in all respect as per the entire satisfaction of Engineer-in-Charge.

Main incomer MCCB/MCB of suitable capacity of L&T / Schnieder/ABB make on the feeder for pumping set confirming to BIS 2516-1985 (Latest edition) complete in all respect as per the entire satisfaction of Engineer-in-Charge.

Individual Starter incomer MCCB/MCB of suitable capacity of L&T / Schnieder/ABB make on the feeder for pumping set confirming to BIS 2516-1985 (Latest edition) complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Three phase indicating lamps complete with logged switches for individual motors conforming to BIS 3452 (Part I & II) latest with upto date ammendments complete in all respect as per the entire satisfaction of Engineer-in-Charge.

LED On / Off & Trip indicator and push buttons, Control and power wiring, Power capacitor, Cooling fan 230 VAC, Contorl terminal, Bus Bar, i.e.Bolt, insulator etc. complete in all respect as per the entire satisfaction of Engineer-in-Charge.

Surge supressor device with Isolating MCCB to eliminate the power surges due to lightening and system surges complete in all respect as per the entire satisfaction of Engineer-in-Charge.

Control Transformer to provide a stable control volatge to safegaurd the control circuit of all the components from the voltage surges and spikes complete in all respect as per the entire satisfaction of Engineer-in-Charge.

Independent Control Panel with Switch Fuse Unit and Fuses of Suitable Amperage to eliminate the KItKat fuses of HPSEB Of reputated make i.e JSV Approved complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Providing double flanged cast steel sluice valve, ASA-150 of Leader/BHEL/ Kirlosker/Kilburn make and one step higher then delivery line of pump and capable of withstanding normal seat pressure as per BIS standards with upto date ammendments) complete in all respect as per the entire satisfaction of Engineer-in-Charge.

Providing double flanged cast steel reflux valves class, ASA-150 of Leader/BHEL/ Kirlosker/Kartar/Kilburn make for rising main and capable of withstanding normal seat pressure as per BIS standards with upto date ammendments) complete in all respect as per the entire satisfaction of Engineer-in-Charge.

Providing 100mm dia circular dial analog pressure gauge of suitable range of Fiebig /Bourden/ PREGA/precision make complete with all accessories such as stop cock, copper tubing etc.as per IS: 3624-1987 with upto date ammendments complete in all respect as per the entire satisfaction of Engineer-in-Charge.

Providing discharge meter of standard make to be fixed on the rising main in pump house as per the directions of the Engineer in charge as per IS:2373:1981 with upto date ammendments complete in all respect as per the entire satisfaction of Engineer-in-Charge.

Installation of all the items apparing as per the schematic drawing complete in all respect as per the entire satisfaction of Engineer-in-Charge.

Providing and laying copper PVC insulated armoured power cable (One cable carrying all the three phases) of suitable size and capacity to motors and all other electircal equipments as per IS:1554(P-I) 1988 or latest ith upto date ammendments of siemens/GLOSTER /IEC/ICC/EICO/NATIONAL/GRANDLAY make including all other accessories such as thinbles, flexible pipes,solders,nuts and bolts cable glands etc. laid in pipes or trenches under floor complete in all respect as per the entire satisfaction of Engineer-in-Charge.

(a) Motor side (From switch to starter and starter to motor) complete in all respect as per the entire satisfaction of Engineer-in- Charge.

(b) Supply side (From Meter of HPSEB to bus bar and switch) complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Providing and fixing double loop earthing with GI plate 600mmx600x3mm thick electrode complete with material such thimbles nuts and charcoal and common salt, 25mmx5mm copper strips as per IS:3043:1987 with upto date ammendments for motors and other electrical equipments and digging of pits etc. complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Low Cost Automation System:- PLC (Programmable logic controller) with appropriate digital and analog inputs and outputs to give automatic command to Star Delta Starter Panel/ Energy Saving Variable Frequency Starter Panel Make: JSV Approved complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Electronic relay card 8 channel complete in all respect as per the entire satisfaction of Engineer-in-Charge.

SMPS 4.5 Amps to energise PLC system complete in all respect as per the entire satisfaction of Engineer-in-Charge.

HMI (Human Machine Interface) 7" display for Monitoring and Controlling of Centrifugal pumps Make:JSV Approved complete in all respect as per the entire satisfaction of Engineer-in-Charge.

Control MCB for Automation System complete in all respect as per the entire satisfaction of Engineer-in-Charge.

Level Sensor to indicate the water level of tank remotely complete in all respect as per the entire satisfaction of Engineer-in-Charge.

Shielded Data Cable for Communication of Level Sensor with PLC complete in all respect as per the entire satisfaction of Engineer-in-Charge.

ASHISH RAWAT

KULBINDER SINGH GOVT CONTRACTOR