8163/GE/SMB/T-50/2023-24/E8 SPECIAL REPAIR TO BLDG NO P50 OR MD ACCN AT BHIM LINES UNDER GE SAMBA

Amount

Rendering 15 mm thick on fair faces of brick or concrete surface walls in cement mortar 1:4 , rendering is to be finished even and fair without using extra cement (up to 2nd storey with necessary scaffolding) including Taking down cement plaster of any description on brick or stone walls or from concrete surface including raking out joints, hacking for key, scrubbing down with water etc, and removing unserviceable material outside cantt area, complete all as specified and as directed.

Rendering cement plaster, 10 mm thick on fair faces of brick/concrete surfaces of wall in cement mortar 1:6 finished even and smooth w/o using extra cement including Taking down cement plaster of any description on brick or stone walls or from concrete surface including raking out joints, hacking for key, scrubbing down with water etc, and removing unserviceable material outside cantt area, complete all as specified and as directed.

Rendering 5 mm thick on fair faces of brick or concrete surface ceilings, in cement mortar 1:3 , rendering is to be finished even and smooth without using extra cement including Taking down cement plaster of any description on brick or stone walls or from concrete surface including raking out joints, hacking for key, scrubbing down with water etc, and removing unserviceable material outside cantt area, complete all as specified and as directed .

RCC M-15, nominal mix, type B-1(1:2:4), using 20mm graded crushed stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like,Including Demolition of reinforced cement concrete of any discription ground to 2nd floors and removing the rubbish from the work site out side defence premises complete all as specified and as directed.

supply only Liquid water proofing compound complete all as specified and directed.

TMT mild steel bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for column, hooking end and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

Use and waste form work to soffits of suspended slabs such as roof slabs, floor slabs landings and similar work, not exceeding 200mm thick (horizontal or sloping) for rough finished surfaces of concrete, complete all as specified and directed.

Use and waste form work to edges of concrete flats, treads, break in floors, window cills, concrete railings, openings in concrete walls, floor and roof and not exc. 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc. 10cm but n.exc. 20cm wide for fair finished surfaces of concrete, complete all as specified & directed

Complete removal of existing water proofing treatment of any description incl under layer, taking down of cement plaster/demolition of cement concrete any thickness and removal of debris off the premises including grubbing up of trees and preparation of concrete surfaces by scrubbing down with steel brushes and cleaning with water to remove all loose dirt/dust.

P.C.C 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in padding over roof finished and laid to required slope complete all as specified and as directed.

Rendering 15mm thck in CM 1:4 on Concrete surfaces of roof finished fair & even and including mixing of water proofing compound (WPC shall be measured and paid separately)

APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified and directed .

Brick work with subclass 'B' bricks, old size bricks, straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 including Demolition of brick work built in cement mortar or cement lime mortar incl all quoins, arches pillars etc and removing unserviceable material from the work site ouside defence premises complete all as specified and as directed by Engineer-in-charge

Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 Including Demolition of brick work built in cement mortar or cement lime mortar incl all quoins, arches pillars etc and removing unserviceable material from the work site ouside defence premises complete all as specified.

Providing, cement concrete 1:2:4 type B-1 (using 20mm graded aggregate ), in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, incuding demoition old cement concrete and through way out side defence land complete all as specified and directed by engineer in charge .

Rotational moulded polyethylene water storage tanks of 500 litres capacity,(cylindrical vertical with closed top) with plastic lid cover, triple layered, white, hoisted and fixed in position all as specified in SSR Part-I including PTMT Ball valves high pressure with epoxy coated Aluminium rod & high density plastic ball complete, screwed for iron pipe or brass ferrule and fixed for 20 mm bore pipe, & making connections including old Dismantling water tanks and removing of water storage tanks (Cap. 250 ltr to 500 ltr ) complete all as specified.

Gun-metal, globe or gate valves, (with half turn) ,screwed both ends for iron pipe of 20 mm bore pipe, including making connections complete all as specified and fixed.

GI tube'medium grade' galvanised, 15 mm bore, ISI marked with all fitting such as bends, tees,elbows, unions,short pieces, connectors, back nuts etc and fixed complete to walls and ceilings or laid in floors,Including Taking up or down old steel tubing pipe and connections, complete all as specified and as directed.

GI tubes 'medium grade' galvanised, 20 mm bore, ISI marked with all fitting such as bends, tees,elbows, unions,short pieces, connectors, back nuts etc and fixed complete to walls and ceilings or laid in floors, Including Taking up or down steel tubing pipe and connections, complete all as specified and as directed.

Cutting chases, pinning in , making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings,steps,cills,sunshades,shelves,lintels etc,and cutting chases for concealed water tubing or concealed conduit wiring,etc,and making good,cutting n.exc 10cm girth in brick walls, complete all as specied and directed.

Non - skid / Anti skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over and including 15 mm thick screed bed in CM 1:4. Including Dismantling floor, hearth or wall tiling including cement mortar bedding, terrazo dado from wall surface (but not backing), removing serviceable tiles to store and rubbish off the premises. Complete all as specied and directed.

Glazed ceramic coloured tiles in vertical surface 300x450x7 mm thick, set and jointed in neat cement slurry and pointed white or colored cement to match the surface over and including 10 mm thick CM 1:4 all as specified. Including Dismantling floor, hearth or wall tiling including cement mortar bedding, terrazo dado from wall surface (but not backing), removing serviceable tiles to store and rubbish off the premises. Complete all as specied and directed.

Non skid coloured ceramic tiles 7 to 8mm thick(square/rectangular joint free) area of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screed bed or bedding layer of mortor 15mm thick in CM 1:6, Including Dismantling floor, hearth or wall tiling including cement mortar bedding, terrazo dado from wall surface (but not backing), removing serviceable tiles to store and rubbish off the premises. Complete all as specied and directed.

Description all as item No 23 above but as in vertical surfaces dado/skirting over and including a backing coat of CM 1:4, 10 mm thick complete.

Taking down chowkhats or frames with shutter (without taking off shutter from the frame) n.exc 1.5 Sqm each including cutting holes for taking out hold fast or dismantling brick work and removing from site all as specified.

Taking down chowkhats or frames with shutter (without taking off shutter from the frame) exc 1.5 Sqm & n.exc 4 Sqm each including cutting holes for taking out hold fast or dismantling brick work and removing from site all as specified.

Pressed steel frames of size 125mm x 60mm made out of size 1.25mm thick MS sheet for doors single rebated including mild steel hinges medium weight 100 mm long and 25mm x 3mm flat iron in holdfast,tie bar including necessary fixing lugs, hold fast, lock strike plate and fixing arrangement etc complete as specified and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 including PCC 1:3:6 as in back fill to chowkats all as Specified.

Pressed steel frames of size 105mm x 60mm made out of size 1.25mm thick MS sheet for doors double rebated including mild steel hinges medium weight 100 mm long and 25mm x 3mm flat iron in holdfast,tie bar including necessary fixing lugs, hold fast, lock strike plate and fixing arrangement etc complete as specified and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 including PCC 1:3:6 as in back fill to chowkats all as Specified.

30mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as directed by Engr-in-Charge.

35mm thick 2nd Class hard wood glazed,gauzed and skelton shutters open rebated and prepare to receive glass, gauge etc but divided into squares with plain chamfered or rounded mitred and rebated sash bars,stiles and rails as specified in SSR Part-I Sec 8 clause 8.24 (a) complete all as specified

Anodised aluminium frame for doors,windows, ventilators with one or more rebates including joining cleat forfixing etc. complete all as specified, complete all as specified and directed by Engr-in-Charge.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppplying and fixing in the frame at site as per specification & drawing complete all as specified and as directed .

Factory made steel windows double shutter box type, outer frame made out of ERW TUBE 'P' section (60x45x25mm) and shutters of ERW TUBE 'P' section (50x35x20mm) operable shutters side hung includding pistol hinges with two Nos of MS Tower bolts 150mm size on each shutter steel handle and stopper of 'Z' section as specified complete with sash bars devetailed or welded ready for glass fixing and wire gauzed fixing with suitabel fittings/openning for cooler/AC where required .Steel windows will be double shutter external glazed and internal wire gauzed complete all as specifed and as per Drg No CEPZ/TD-324/07 1/3 to 3/3 all as specified and directed . NOTE: The quoted rate against the above item shall also include (i) 04 Nos MS Steel lugs of 20x5mm MS flat 20cm long over all welded to frames (ii) PCC block for embedding lugs.

Ditto all as per item No 33 but in Ventilators any size.

Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165, complete all as specified and directed.

Pressed steel cup board frame of MS sheet 1.25 mm thick size of frame 60 x 40 mm with rebate of 20 mm wide and 12 mm deep including PCC 1:2:4 as in filling to back of chowkhats including butt hinges 100 mm long, complete all as specified and directed.

Prelaminated MDF board 19 mm thick as in shutters/shelves (exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work including lipping (15 mm thick three sides and 20 mm thick lipping hinge side) around the shutter complete all as specified and as directed.

16 to 18 mm thick green udaipur marble in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, over 15 mm thick CM 1:4 Including Dismantling Stone slabs in roofs, suspended floors, chajjas, landings, etc., any thickness, jointed in any mortar complete as directed by Engr-in-charge.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified.

3.5 mm thick sheet glass ordinary quality glazing with oil putty or any type of beads in square n.exc. 0.5 Sq each pane in any type of frame of iron/Steel/Wood/Aluminium as required at site complete all as specified (upto fourth storey with necessary scaffolding), all as specified.

3.5 mm thick figured glass, pin head type and glazing with oil putty or any type of beads in square n.exc. 0.5 Sq each pane in any type of frame of iron/Steel/Wood/Aluminium as required at site complete all as specified (upto fourth storey with necessary scaffolding), all as specified.

Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staple, complete all as specified and directed

Butt hinges of mild steel cold rolled medium weight of size 100mm, complete all as specified and directed

Aluminium anodised, barrel tower bolts size 150 mm of extruded section and fixed complete all as specified.

Aluminium handles, fabricated type, anodised Size-100mm, anodised section and fixed complete all as specified.

Aluminium alloy, anodised, sliding door bolt Size- 250 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified.

Hasp & staple safety type aluminium anodised with mild steel hinges Spin including bolt to hinges plate fixed with screws of 75 mm in length.

Aluminium hanging floor door stopper,Twin rubber stopper,size 100mm , anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. All as specified and directed

50 mm magnetic catches with brass body and striking plate including letting in as fixed complete all as specified and directed.

40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified.

Aluminium bottom door seal with brushes, length 1.2 mtr, fix with screw, suitable for wooden door complete all as specified.

Mild steel helical ordinary rat tail rod pattern springs 300mm including roller and roller plate complete including fixing to pressed steel frames necessary welding work all as specified and as directed.

UPVC (SWR) type B pipes 110 mm bore single socketed in any length with rubber ring joints, laid in trenches or in floors,Including Dismantling PVC/Cement/CI pipes 50 to 110 mm dia including all fittings like bend,branch pieces, connectors, heel rest bend etc and removing from site complete all as specified and as directed by Engineer-in-charge.

UPVC (SWR) type B pipes 110 mm bore single socketed, in any length with rubber ring joints fixed to walls including stack clamp of GI flat 30mm wide 2mm thick fixed to wall with nail at spacing of 1m center to center , Including Dismantling PVC/Cement/CI pipes 50 to 110 mm dia including all fittings like bend,branch pieces, connectors, heel rest bend etc and removing from site complete all as specified and as directed by Engineer-in-charge.

UPVC (SWR) type B pipes 75 mm bore single socketed in any length with rubber ring joints, laid in trenches or in floors, Including Dismantling PVC/Cement/CI pipes 50 to 110 mm dia including all fittings like bend,branch pieces, connectors, heel rest bend etc and removing from site complete all as specified and as directed by Engineer-in-charge.

UPVC(SWR) type B pipes 75 mm bore single socketed, in any length with rubber ring joints fixed to walls including stack clamp of GI flat 30mm wide 2mm thick fixed to wall with nail at spacing of 1m center to center ,Including Dismantling PVC/Cement/CI pipes 50 to 110 mm dia including all fittings like bend,branch pieces, connectors, heel rest bend etc and removing from site complete all as specified and as directed by Engineer-in-charge.

UPVC (SWR) , bends for 75 mm bore , complete all as specified and as directed.

UPVC (SWR) , bends with access door for 75 mm bore , complete all as specified and as directed.

UPVC(SWR) , bends for 110 mm bore complete all as specified and as directed .

UPVC(SWR) , bends with access door, for 110 mm bore complete all as specified and as directed.

UPVC(SWR), junction single, (Double 'T' / 'Y') with access door equal or unequal for 75 mm bore , complete all as specified and as directed.

UPVC(SWR), junction single, (single 'T') with access door equal or unequal for 110 mm bore , complete all as specified and as directed.

UPVC (SWR) , reducers 110 mm dia complete all as specified and directed.

UPVC (SWR) vent cowl 75 mm dia complete all as specified and directed.

UPVC (SWR) floor trap plain with grating having dia meter of out let 75mm including jointing with solvent cement to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

UPVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified.

20mm outer dia plainchromium plated (SS Finish) decorative drapery rod of thickness 20 gauge and including side end cap with stainless brackets near to ends with stainless steel finish for at both ends. Complete all as specified and as directed.

15 mm Bib taps,chromium plated fancy type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed ,complete all as specified and directed.

15mm bore angle valve with wall flange , cast copper alloy, chromium plated fancy type screwed for 15 mm iron pipe, complete all as specified and directed.

15mm bore angle valve with long shank and cup (concealed type) cast copper alloy, chromium plated fancy type screwed for 15 mm iron pipe, complete all as specified and directed.

15mm bore CP Pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

Towel Ring of PTMT (CP finish) fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms) , complete all as specified and directed.

Corner Glass Shelf (with Bracket) complete all as specified and directed.

PVC connection 15 mm x 450 mm including brass check nut at both ends screwed for iron pipe of 15 mm bore.

Brass chromium plated shower rose with or without swivel joints, 125mm size, including fixing to steel pipe or union.

Vitreous China, wash basin white, flat back , size 400mmx300 including brackets of any size, including cutting for and pinning in ends of brackets or erecting stand including fixing and supply of waste pipe of 32 mm dia, waste coupling of chromium plated brass. complete all as specified and as directed.

10 litres Capacity PVC valveless,syphonic action type,flushing cistern,low level,white with inlet,ball valve,float and handle including brackets & Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern & fixing only in repairs of High or low level fluslhing cistern (exclusive of brackets), and connections to pipes and fixing of chain and pull, or lever, if any .

Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and as directed.

Vitreous China squatting pan, ‘Orissa’pattern, size 580 x 440 mm white, with integral foot rests including provision of lime concrete bedding (excluding flushing cistern and flush pipe complete all as specified and as directed .

Sinks with drainage board made of stainless steel 1.00 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm & bowl size 410mm x 355mm x 200mm complete with CP waste coupling & PVC waste pipe complete all as specified and directed .

Kitchen stainless steel plate rack made out of 1 mm thick sheet and having partions as per sample. The over all size (30"x36"x10") fixed with steel fastners or steel screw complete.

Preparation of new plastered or unplastered surfaces of ceilings and applying three coats of white washing complete all as specified and as directed.

Preparation of new plastered or unplastered surfaces of walls and applying three coats of white washing complete all as specified and as directed.

Preparation of new plastered surfaces of walls & applying two coats of oil bound distemper including smoothing of plastered surface by applying wall care putty and one coat of primer complete all as specified and directed.

Preparation of new plastered/ concrete surfaces of walls and applying two coats of cement based paint over and including one coat of primer (up to 2nd storey with necessary/scaffolding) complete all as specified and directed.

Preparation of old decorated brick /concrete, plastered /un-plastered surfaces of walls, pillars, cornices etc (upto 2nd storey bldgs) by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots, rubbing with sand paper and applying two coat of lime white wash on the walls, pillars, cornices etc. complete all as specified and directed.

Preparation of old decorated brick /concrete, plastered /un-plastered surfaces of ceilings, cornices etc by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss, efflorescent salts, oil, greasy spots , rubbing with sand paper and applying two coat of white wash on ceiling, complete all as specified and directed.

Preparation of old decorated brick/concrete/ plastered/unplastered surfaces of walls, Pillars, cornices etc by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts, trading oil and greasy spots, rubbing with sand paper and applying two coat of oil bound distemper on walls, pillars,cornices surface including making good uneven surface/holes with birla wall care putty coloured in same shade where ever required etc. complete all as specified and directed.

Preparation of old decorated brick/concrete/ plastered/unplastered surfaces of walls, Pillars, cornices etc by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts, trading oil and greasy spots, rubbing with sand paper and applying two coat of cement base paint on walls, pillars, cornice etc (upto 2nd storey with necessary scaffolding complete all as specified and directed.

Preparation of new wooden surfaces having width/girth exceeding 10 cm and applying two coat of synthetic enamel paint over a coat of pink primer. complete all as specified and directed

Preparation of new steel surfaces having width/girth exceeding 10 cm and applying two coat of synthetic enamel paint over a coat of red oxide primer . complete all as specified and directed

50mm thick cement concrete 1:3:6, type C1, using 20mm graded crushed stone aggregate as in plinth protection, laid in slope of 1:20 and surface finished even and smooth without using extra cement including making joint at 3m interval and at each corner the joint shall be filled with bitumen mastic filling to full depth (comprising one part hot blown bitumen 85/25 and two part of sand), complete all as specified and directed.

25 mm thick cement concrete 1:2:4, Type B-0 (12.5mm graded aggregate) as in sub-base of floor for tiles/Kota stone all as specified.

Kota stone floor 16-20 mm thick, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over screed bed or bedding layer of mortor 15mm thick in CM 1:6 ) complete all as specified and directed.

Kota stone floor 16-20 mm thick,in skirting,set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10 mm thick in CM 1:4, complete all as specified and directed.

75mm thick Cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate) as in Sub Base for Interlocking tiles or paver Block, Hardstanding etc all as specified and directred.

Coloured Chequered cement concrete tiles 20cm x 20cm x 25mm thick/25cm x 25cm x 25mm thick, set, jointed with cement and pigments and pointed in neat cement slurry as in path etc including 15mm thick screed bedd in CM 1:4,complete all as specified and directed.

PCC 1:3:6 type C-1(using 20 mm graded cr. stone aggr)as in kerbs or mud stops, rounded or chamfered on edges, in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60cm in height, coping, kneelers, apex stones, bed plates, water troughs and like incl weathering, slightly rounded or chamfered aangles and throating all as spd & directed.( for sides of chequered tiles )

Demolition of plain cement concrete in ground floors or above ground floor and paving n.exc 15 cm thickness (Below or above ground level)

Taking down old unserviceable aluminium point wiring (light, fan, socket , power socket and bulk head fittings) from PVC/metallic conduit,on surface wiring, on wooden batten/casings & caping complete, including fixture and fittings such as switches, ceiling roses,pendents holder, regulators, sockets and defective main switch/DB/MCB/Metal plug etc. by unscrewing carefully from boards etc complete all as specfied and directed.

Point wiring for one light/one fan controlled by one switch with 1.5 sqmm single core PVC insulated unsheathed multistranded copper conductor (FRLS) in and including PVC concealed conduit having thickness not less than 1.8 mm with sunken box having thickness not less than 2.0 mm thickness with 3 mm bakelite laminated socket ISI marked for switches and sockets , including 1.5 sqmm single core PVC insulated unsheathed multistranded copper conductor (FRLS) as earth continuity conductor connected to comman earth dolly in and including cutting chiseling for concealed piping as required and making good disturbed surface area and white wash /colour wash to matching with the existing colour and all as specified and directed . Note: (a) Insulation test of point wiring (b) colour coding is to be maintained .(Ph-Red, N-Black, Half -Yellow, Earth- Green)

Ditto all as per srl item No 103 above but for One light point controlled by two way switch complete all as specified and directed

Ditto all as per srl item No 103 above but for call bell point complete all as specified and directed

Ditto all as per srl item No 103 above but for 3 pin 5 amps indipendent board complete all as specified and directed.

Ditto all as per srl item No 103 above but for 3 pin 5 amps on same board complete all as specified and directed.

Point wiring for one power point controlled by one switch with 2.5 sqmm single core PVC insulated unsheathed multistranded copper conductor (FRLS) with in and including PVC concealed conduit having thickness not less than 1.8 mm with all fittings including anodise pressed steel sunken box having thickness not less than 2mm with 3mm bakelite laminated sheet ISI marked suitable for 5 pin 15 Amps sockets outlet , including 2.5 sqmm single core PVC insulated unsheathed multistranded copper conductor (FRLS) as earth continuity conductor connected to comman earth dolly in and including cutting chiseling for concealed piping and making good disturbed surface area and white wash /colour wash to matching with the existing colour and all as specified and directed. Note: (a) Insulation test of point wiring (b) colour coding is to be maintained .(Ph-Red, N-Black, Half -Yellow, Earth- Green)

Switch piano flush type single pole 10 Amp, two way, AC 230 volts SP complete all as specified and directed.

Switch piano flush type one way 5 Amps SP complete all as specified and directed.

Switch piano flush type single pole 15 Amp, one way, AC 230 volts SP complete all as specified and directed.

Socket outlet multipurpose 3 pin 5 Amps flush type complete all as specified and directed.

Switch Socket combination multipurpose 2 in 1, 6 pin 5 and 15 Amps controlled by one switch flush type universal.

Bell push flush type with indicatior 6 Amps complete all as specified and directed

Electronic bell ding-dong AC 230 Volts single pole complete all as specified and directed

Ceiling rose 65 x 50mm three terminals complete all as specified and directed.

Ceiling fan regulator electronic type 5 stage speed variation,socket type is size, ISI marked complete all as specified and directed.

Lamp holder/batton holder/angle holder insulated body(Metal ring) with back bakelite plate suitable for batten fittings, complete all as specified and directed.

LED tube light fitting 20 watt, 230 volt,box type complete bipin holders, connector,mounted on PVC block and retro LED rod of 20 watt power factor > 0.9 complete complete with all accessories internally pre wired and including connecting up with three core twisted flexible copper conductor cable with suitable size mounting on rectangular PVC black complete all as specified and directed,LED tube rod ,make :Havells,Cat Part No: REGALBATTENT5UPTO1X22WSSBSWH and LED tube light batten ,make :Havells, Cat Part No : PHOTONULTRAE2.01213T8SSTL20WLED865SPC or technocommerically equivalant make of Crompton/Philips. Note: (i) Contractor shall produce LM 79 & LM 80 test report form OEM owned NABL accredited laboraory. (ii) Contractor shall give gurantee of complete fitting/ fixtures for minimum of 2 years form the date of completion. (iii) Contractor shall conduct the inspection of company representative at site before installation of fittings/fixtures at no extra cost. (iv) Contractor shall arrange 70 % material at site for approval of GE before incorporation in the work.

Submain wiring in and including PVC conduit 1.8 mm thick ,20 mm dia with two run of PVC insulated, unsheathed multistranded copper conductor of 4 sqmm(FRLS) and one run of PVC insulated,unsheathed multistranded copper conductor 4 sqmm (green in colour) for earth continuity conductor and connected to common earth dolly with thimble etc including taking down old U/S brunt sub main wiring from wooden battens, complete all as specified and directed. (Two run of 4 sqmm plus one run 6 sqmm of earth wire will be measured as 1RM) Note: (a) Insulation test of point wiring (b) colour coding is to be maintained .(Ph-Red, N-Black,Earth- Green)

Environmental friendly ultra modern, energy seving, surface mounted, decorative hexagon Bulk head 10 watt back-lit LED luminaire comprissing of high brightness LEDs cat Part No HEXAFT10WLED857SSYMBOPC of Havells or technocommerically equivalent make of philips/Crompton

Sheet metal enclosures distribution boards, double door ,VTPN, 415 volts 4 ways (one incoming three phase & twelve out goings single phase )for MCCB & MCB,s comprising three phase four wire copper strip bus bar of appropriate capacity complete all as specified and directed and comprising of the following a) MCCB FOUR POLE 100 AMPS AC 415 VOLTS 16 KA=01 NO (for incoming ) (b) MCB SP 63 amps = 4 Nos (for outgoings) . Note :- (i)The DB shall be VTPN series of Make : Schneider ,cat part no: A9HVD04L or equivalent make of L&T/ ABB/ Legrand/BENLO . (ii) The DB shall be flush fixed and making good the disturbed surface matching with existing specifications shall be part of job at no extra cost. (iii)connection of the MCCBs/ MCBs with cable shall be made through appropriate size pin /bottle type thimble properly crimped. (iv) All the vacant holes of the DB shall be provided with blank plates of appropriate size. (v) Double continuous earth wire shall be provided for each three phase DB from earthing mains dolly. (vi) cutting chasing shall be part of job at no extra cost .

Sheet metal enclousre for DBs when MCB to be used double door powder coated factory made flush fixed complete with 200 amps rated bus bar 240 volts single phase 12 ways complete all as specified and directed.

MCB SPN 63 amps 240 Volt 'B' series complete all as specified and as directed.

MCB SPN 6 to 32 amps 240 Volt 'B' series complete all as specified and as directed.

Earthing complete with galvanized steel earth plate electrode 600x600x6mm thick buried directly in the ground (earth pit not less than 2.25 mtr deep below the normal ground level ) with top edge of plate not less than 1.5 mtr below the normal ground level connected to galvanized iron wire 4mm dia as earth lead by means of nuts bolts,washers of GI upto test point,GI tubing light grade 15mm bore protection pipe and GI watering pipe 20mm light grade with funnel and wire mesh ,charcoal and salt,40mm thick pre-cast RCC M-15 (nominal mix) cover reinforced with XPM weight not less than 4 kg /sqm with suitable handle of 6mm dia MS bar and angle iron 40x40x3mm frame for cover ,PCC M-15 (nominal Mix) pit,excavation and earth work in any type of soil and removing surplus soil to a distance n.exc.50m) and connecting, Testing on complition, Complete all as specified and shown on Electrical Plate No 3 of SSR-2009 Part-1. complete all as specified and directed. Notes:- 1. Earth lead & protection pipes length upto & including 7.50 mtr is included in the quoted rate. 2. Soil should be free from stone, boulders, aggregate, gravels etc.

Excavation in trenches n. exc. 1.5 mtr wide and n. exc. 1.5 mtr in depth for laying of UG cable and getting out in any type of soil complete all as specified and directed . Note :Rates for demoition /excavation in PCC flooring shall be deemed included in quoted rates .No extra shall be paid to the contractor.

Returning filling in, including spreading, watering and well ramming in layers not exceeding 25 cm thick in any type of soil complete all as specified and directed .

Removing excavated material not exceeding 50 mtr and depositing where directed in a level not exceeding 1.5 mtr above the starting point of any type of soil complete all as specified

Sand cushioning to under ground electric cable a layer of 8 cm thick before laying the cable and 15 cm thick after laying and stretching the cable complete all as specified in clause 19.75 of MES Schedule part-I (2009) Note : Sand shall be of good quality as specifed and punned thickness shall be measured and paid.

Material and labour for sub class 'B' bricks well burnt old size laid dry flat for protection of cable complete all as specifeid and directed.

GI pipe in replacement ( Light grade ) for protection of LT cable fixed to walls/ poles/road crossing including suitable size clamps complete of size 50 mm bore , complete all as specified and directed

Supply, laying and testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of sixe 25 sqmm 4 core complete all as specified and directed.

Note:- The contract sum arrived after deduction of amount of Sch of credit as listed in tender Documents.

SIDDAHANT ENTERPRISES

s k construction co

M/S NAGAR BUILDERS

M/S RAJESH SHARMA & CO.

BALI ENTERPRISES