Construction of New Circuit House at Ahwa, Dist. Dang.

No figures

1 Excavation for foundation upto 1.5 m depth including 2426.00 Cumt 125.85

sorting out and stacking of useful materials and

disposing off the excavated stuff upto All lift and

lead.(A) Loose or soft soil

2 Excavation for foundation for depth from 1.5 m to 3.0 456.00 Cumt 174.56

m including sorting out and stacking of useful

materials and disposing off the excavated stuff upto All

lift and lead.(B) Dense or Hard soil

3 Filling in foundation and plinth with sand in layers of 262.00 Cumt 489.28

20 cm. Thickness including watering ramming and

consolidating etc. comp.

4 Filling available excavated Earth (Excluding Rock) in 752.00 Cumt 137.47

trench plinth side of foundation . in layer not excluding

20 cm in depth consolidation each deposited layer by

ramming and watering etc. complete

soil in layer of 20 cm in thickness including ramming

watering and consolidating etc. complete

6 Applying general insecticide pest control treatment to 1317.00 Sqmt 54.04

floors, cupboards etc including labour material etc.

complete. Using Imidacloprid 30.5 SC. As Per

Part -II (0.075% concentration by mass) is

recommended 10.5ml chemical diluted with 5 liters of

water application 0.5 liters chemical/ sqm of surface is

recommended as per I.S.

7 Providing and laying cement concrete 1:3:6 (1-Cement 52.00 Cumt 3106.67

: 3- coarse sand : 6- machine cut stone aggregates

mm nominal size) and curing complete excluding cost

of formwork in (A) Foundation and Plinth

8 Providing and laying controlled cement concrete M150 765.27 Cumt 4801.26

for curing complete including cost of formwork but

excluding the cost of reinforcement for reinforced

concrete work in PCC

9 Providing and laying controlled cement concrete M250 977.28 Cumt 5795.48

and curing complete including the cost of formwork

and excluding reinforcement for reinforced concrete

work for Foundations, Footings , Mass concrete

Column up to GL , Ground/plinth Beam

10 Providing and laying controlled cement concrete M200 1672.50 Cumt 6691.38

and curing complete including the cost of form work

but excluding the cost of reinforcement for reinforced

concrete work in Plinth Slab, Columns, Beam, Chhajja,

Lintal, Slab, Stair, RCC Wall, Coping etc. For All Floor

11 Extra for additional height of propping and centering 45.50 Sqmt 407.75

where the height of propping and centering exceeds

.O M between supporting floor to ceiling including

temporary brick or stone pillars for supporting as

required. (iii) Height more than 4.0 M.and up

12 Providing IS Mark TMT FE-500D bar reinforcement for 254384.70 Kg 77.57

RCC work including bending & placing in position

complete up to All floor Level

13 Providing and fixing stainless steel railing made from 261.00 Sqmt 3880.93

anticorrosive SS 304 grade pipes, consisting of 50 mm

dia (16 gauge) handrail and 38 mm dia (16 gauge) SS

304 grade balusters placed at 1.20 m centre-to-centre,

firmly fixed into the RCC slab. The railing shall include

horizontal SS pipes of 25 mm dia (16 gauge) spaced at

0.20 m centre-to-centre, fixed using 18.75 mm dia (16

gauge) SS pipe connectors with the balusters. The

entire assembly shall be provided with all necessary

brackets, base plates, welding, grinding, buffing, and

mirror polishing, complete with all accessories as per

the approved detailed drawings and as directed by the

Engineer-in-Charge. The rate shall be inclusive of all

materials, labour, fittings, fixing in position, finishing,

cutting, wastage, scaffolding, loading, unloading, and

transportation to site — complete in all respects.

14 Providing and fixing a modern glass 1.2m height 195.00 Sqmt 4250.59

railing system consisting of stainless steel SS-304

grade balusters and handrail, including 50 mm dia (16

gauge) SS-304 top handrail and vertical SS-304

balusters/side brackets spaced at 1.20 m centre-to-

centre, securely fixed into the RCC slab or stair waist

as per design. The railing shall be fitted with 10–12

mm thick toughened clear glass panels fixed using SS-

304 grade point-fixed glass studs/rails, glass clamps,

or slot-type fittings as shown in the approved

drawings. All fittings shall include necessary SS-304

connectors, spacers, anchoring fasteners, and

hardware for firm and vibration-free installation. The

complete assembly shall include precision cutting,

edge polishing of glass, alignment, grinding, welding

(where required), buffing, and mirror-finish polishing

of stainless-steel components. The rate shall include

all materials, labour, scaffolding, handling of glass,

fixtures, adhesive pads, silicone sealing (if required),

fixing in position, wastage, loading, unloading,

transportation to site, and completion of work as per

approved architectural details and as directed by the

Engineer-in-Charge.

15 Providing and fixing Hand Railing 30 cm Height 55.00 Rmt 1901.83

Stainless Steel Hand Railing made from anticorrocive

304 grade S S pipe of 50 mm dia (16 Gauge) as hand

rail with S S 304 grade Baluster of 38 mm dia (16

Gauge) as a vertical support fixed in RCC member at

1.2m c/c S S pipe with baluster including accessories

as per detailed drawing as directed etc. complete.

16 Providing and fixing full-height toughened glass 112.00 Sqmt 4250.59

partition made from 12 mm thick clear toughened

glass panels, installed in continuous vertical alignment

along the staircase using SS-304 grade point fittings /

patch fittings / floor pivots fixed at floor level, wall

level, and intermediate supports as per approved

design. The glass panels shall be factory-cut, machine-

polished on all edges, and installed with precision gap

control using neoprene packers and stainless-steel

hardware. All fittings shall be SS-304 grade including

top connectors, side brackets, floor anchors, and

stabilizing clamps, ensuring rigid, vibration-free and

safe installation. Work includes drilling in floors/walls

for anchoring, applying silicone sealant where

required, alignment, leveling, cleaning, handling,

loading, unloading, scaffolding, finishing, and all

accessories required to complete the glass partition in

accordance with approved drawings and as directed

by the Engineer-in-Charge — complete in all respects.

17 Brick work using common burnt clay building bricks 182.00 Cumt 4279.98

having crushing strength not less than 35 kg./Sq.Cm.

in foundation and plinth in Cement Mortar 1:5. (1-

Cement : 5 -fine sand) (B) Conventional below plinth

18 Brick work using common burnt clay building bricks 965.00 Cumt 4597.30

having crushing strength not less than 35 kg./Sq.Cm.

in foundation and plinth in Cement Mortar 1:6. (1-

Cement : 5 -fine sand) (B) Conventional All Floor

19 Half Brick masonry in common brunt clay building 1860.00 Sq m 699.91

bricks having crushing strength not less than

Kg/Sq.Cm. in Cement mortar 1:4 (1- Cement : 4 -

coarse sand ) in foundation and plinth (B)

Conventional in super structure. for All Floor

20 Providing and fixing 150 mm wide, approved quality 1189.00 Sqmt 295.12

chicken wire mesh at junction of brick work and RCC

work or two dissimilar surfaces, at all heights fixed by

nails, rowal plugs or tag before applying the plaster,

including curing, scaffolding all complete as directed.

21 Providing 20 mm thick double coat mala cement 2843.00 Sqmt 310.58

plaster on interior brick / concrete work for plastering

comprising of base coat of 12 mm thick cement plaster

in cement mortar (1 Cement : 4 coarse sand) in rough

finishing and 8 mm thick top coat of cement mortar

1:2 (1 Cement : 2 Coarse sand) finished with trovel

including scaffolding curing etc. complete ForAll Floor

22 Providing 10 mm. Thick Mala cement plaster in single 3742.67 Sqmt 204.62

coat for plastering on ceiling and soffits of stairs and

finished even and smooth in : (I) Cement mortar 1:4

(1 cement : 4 sand) finished with trovel etc. complete.

23 20 mm thick Sand faced cement plaster with 1cmx1cm 5398.00 Sqmt 408.14

grooves as suggested by this office consisting of

mm thick backing coat of C.M. 1:3 ( 1 cement : 3 coarse

sand ) and 8 mm thick finishing coat of C.M. 1:1 (

cement : 1 coarse sand) for all heights as directed etc.

complete. and as per pattern sample aprroved by the

architect or directed engineer in-charge

24 Providing throating or plaster drip and moulding to 868.00 Rmt 45.33

R.C.C. Chhajja.

25 Applying two coats of Acrylic lapy (putty) & two coats 6360.00 Sqmt 40.59

of primer of approved brand and manufacture on new

wall surface to give an even shade including

thoroughly brushing the surface free from mortar

dropping and other foreign matter and sand papered

26 Wall painting (three coats) with plastic emulsion paint 4721.00 Sqmt 128.91

of approved brand with one wall special effect (royal

play) colour and manufacture on undecorated wall

surface to give an even shade including throughly

brushing the surface free from mortar droppings and

other foreign matter and sand papered smooth , shade

approved by office.

27 Painting (two coats) with plastic emulsion paint of 3775.00 Sqmt 134.72

approved brand with one wall special effect (royal

play) colourand manufacture on undecorated ceiling

surface to give an even shade including throughly

brushing the surface free from mortar droppings and

other foreign matter and sand papered smooth , shade

approved by office.

28 Providing and applying Decorative Natural Stone 3064.00 Sqmt 1800.33

Texture Coat Synthetic Plaster consisting of crushed

natural stone chips of 0.5 mm to 4 mm size in proper

gradation, bonded with synthetic resins. The plaster

shall be applied in two coats, each of approximately

2.5 mm thickness, to form a waterproof decorative

surface. The adhesive shall be an aqueous Vinyl

Acetate/Acrylate Co-Polymer Emulsion, wherein the

acrylate component polymerized into the product

imparts good flexibility to the coating. The Co-Polymer

emulsion shall be combined with suitable chemical

compounds to provide specific properties to the final

coating. These additives shall impart fungus and

bacterial resistance, improve water resistance, and

enhance the durability of the coating. The material

shall also exhibit good flow, cohesive finish, and

excellent adhesion, enabling it to penetrate into the

substrate before drying and forming a firm anchoring

grip. The material shall be supplied as a ready-mixed

paste in airtight drums to maintain consistent quality,

with a shelf life as per manufacturer’s

recommendation, complete as directed by the

Engineer-in-Charge.

29 Providing And filling with good quality cinder (steam 53.00 Cumt 521.16

coal) as directed by engineer in charge in sunks in

layers of 15 cm thick,including watering,placing

,ramming well etc as directed, for all floor.

30 Providing and laying China mosaic type water proofing 1029.80 Sqmt 1114.03

treatment on terrace including cleaning the surface by

wire brush as directed including applying neat cement

slurry @ 2.75 Kg/Sq.smt. mixed with water proofing

compound after cleaning the surface, laying cement

concrete using brickbats 25 to 100mm size well

immersed in water with 50% of cement mortar 1:5 (1

cement :5 coarse sabd) mixed with water proofing

compound over 20mm thick layers of cement mortar

1:5 (1 cement :5 sand) to required slope including

rounding of junctions of walls and slabs and after two

days of proper curing, applying second coat of cement

slurry finishing the surface with rate 20mm thick

cement mortar 1:4 and china mosaic tiles and finally

finishing the surface with white cement slurry and

after finishing the whole terrace shall be flooded with

water for a period of two weeks.

31 Providing Plinth Protection to Building including 208.00 Sqmt 2595.20

excavation in ordinary soil and laying cement concrete

1:3:6 using stone aggregates of 40mm nominal size in

foundation layer 150 mm thick+ 200mm thick sand

layer below pre-cast Rubber Dye inter locking

concrete block 60mm thick with grade of concrete

M300 pneumatic compressed by mechanically pressed

and as per approved design including 75mm Sand

layer for levelling and filling the joint with sand in

proper line and level etc. complete, Including

Providing and fixing pre-cast concrete kerb stone of

grey cement based concrete block 30cm length, 30cm

height and 15cm thick made of M250 grade concrete

as per approved design and including excavation for

fixing in proper line and level, filling the joint with C:M

1:3 (1cement:3 fine sand) etc. complete.

32 Providing and fixing CNC laser-cut metal jali for 297.00 Sqmt 4749.12

building façade, fabricated from 2 mm to 3 mm thick

Mild sheet of approved make and quality, cut using

CNC laser cutting technology in the approved pattern

and design as per detailed drawings. The jali panels

shall be provided in required size and shape to form

the specified elevation, including necessary stiffeners,

bracing, and structural framework at the rear side for

proper support and rigidity. The panels shall be fixed

over a suitable MS angle or box section frame securely

anchored to the RCC or masonry surface with stainless

steel bolts, nuts, and fasteners. The entire surface of

the jali shall be cleaned, treated with an anti-corrosive

primer, and powder coated or spray-painted in colour

as directed by the Engineer-in-Charge to achieve a

smooth and uniform exterior-grade finish. All edges

and cutouts shall be properly ground, smoothened,

and free from sharp burrs. The work shall include

proper alignment, leveling, welding, touch-up of joints,

and finishing complete in all respects as per approved

design, specifications, and instructions of the Engineer-

in-Charge.

33 Providing and fixing in position standard extruded 116.00 Sqmt 4009.70

Aluminium three-track sliding window system (3

shutters + 1 mosquito net shutter) made of colour

anodized extruded Aluminium sections equivalent to

Jindal Series E (30 mm), with section numbers: Frame

Bottom with weep holes – 20928, Frame Top & Side –

20837, Shutter Top & Bottom – 20993, Shutter

Interlock – 20550, Shutter Side (handle) – 20549. The

shutters shall be fitted with 5 mm thick transparent

tinted float glass fixed with EPDM rubber gaskets, and

one shutter fitted with SS wire mosquito mesh jali in

the same Aluminium shutter section. The system shall

include air lock strip, sealant at all joints, and finishing

with powder-coated standard Aluminium fittings,

complete as per window size and detailed drawings.

The rate shall include cost of all materials, labour,

fittings, equipment, and accessories, and the work

shall be carried out as directed by the Engineer-in-

34 Providing and fixing in position standard extruded 12.00 Sqmt 4046.06

Aluminium three-track sliding window (2 shutters +

mosquito net shutter) made of colour anodized

extruded Aluminium sections equivalent to Jindal

Series E (30 mm), comprising: Frame Bottom with

weep holes – Section No. 20928, Frame Top & Side –

Section No. 20837, Shutter Top & Bottom – Section No.

20993, Shutter Interlock – Section No. 20550, and

Shutter Side (handle) – Section No. 20549. The

shutters shall be fitted with 5 mm thick transparent

tinted float glass fixed with EPDM rubber gasket, and

one shutter provided with SS wire mosquito mesh jali

in the same Aluminium shutter section. The system

shall include air lock strip, joint sealing with approved

sealant, and finishing with powder-coated standard

Aluminium fittings, complete as per window size and

detailed drawings. The rate shall be inclusive of all

materials, fittings, fixtures, labour, equipment, and

accessories, and the work shall be carried out as

directed by the Engineer-in-Charge.

35 Providing & Fixing in position standard extruded 17.00 Sqmt 1977.58

approved colour anodised Aluminum Ventilator with

outer frame 65 x 25 mm Stander Box Frame @ Wt

1.094 kg/Rmt with 3mm bajari figure glass fix louvers

fixed to alluminium strip blade including exhaust fave

fitting all required materials, fixtures, fastenning,

labours and equipments as per detailed drawing as

directed. For Ventilators V1

36 Providing and fixing frameless toughened glass Door 11.00 Sqmt 10911.03

with door, using 18mm thick toughened clear glass

featuring a horizontal etching pattern as per the

approved section. The installation includes a 60cm

high stainless steel (SS 304) handle with a matte

finish, along with 60cm fixed glass panels on both

sides. The glass shall be securely mounted on a frame

using SS 304 patches, ensuring stability. The system

shall incorporate a stainless steel (SS 304) lock and

roller mechanism at both the top and bottom,

facilitating smooth operation. All fixtures, fastenings,

and fittings shall be executed as per the instructions of

the Engineer-in-Charge, ensuring proper alignment,

durability, and aesthetic finish.

37 providing and fixing 35 mm thick heavy quality flush 125.00 Sqmt 4694.48

single door shutter, solid core type confirming to

IS:2202 and ISI approved, having 1 mm thick

decorative laminate on both sides, machine-glued PVC

edge banding on all sides, fixed into existing granite

frame (excluding cost of frame). The shutter shall be

complete with 600 mm long stainless steel handle, S.S.

fixtures, locking arrangement of standard make or

equivalent, and 3 Nos. 150 mm long heavy-duty

stainless steel hinges. The door shall be of approved

make, shade, and finish as approved by the Engineer-

in-Charge.

38 Providing and fixing 35 mm thick heavy quality 45.00 Sqmt 4934.86

waterproof flush single door shutter, solid core type

confirming to IS:2202 and ISI approved, having 1 mm

thick waterproof decorative laminate on both sides,

machine-glued PVC edge banding on all sides, fixed

into existing granite frame (excluding cost of frame).

The shutter shall be complete with 300 mm long

stainless steel handle, heavy-duty S.S. fixtures, locking

arrangement of standard make or equivalent, and

Nos. 150 mm long heavy-duty stainless steel hinges.

The door shall be of approved make, shade, and finish

as approved by the Engineer-in-Charge.

39 Providing and fixing 35 mm thick heavy quality flush 3.00 Sqmt 4934.86

Double door shutter, solid core type confirming to

IS:2202 and ISI approved, having 1 mm thick

decorative laminate on both sides, machine-glued PVC

edge banding on all sides, fixed into existing granite

frame (excluding cost of frame). The shutter shall be

complete with 600 mm long stainless steel handle, S.S.

fixtures, locking arrangement of standard make or

equivalent, and 3 Nos. 150 mm long heavy-duty

stainless steel hinges. The door shall be of approved

make, shade, and finish as approved by the Engineer-

in-Charge.

40 Providing and laying 900 mm x 900 mm Double 1388.00 Sqmt 1772.45

charged 10 mm thick Vitrified tiles in flooring laid on

20 mm thick cement mortar 1:6 (1 cement : 6 coarse

sand) on new surface and jointed with coloured

cement slurry including finished with flush pointing &

cleaning the surfaceetc complete for all floors as

directed by Architect or Engineer in chage. (including

cost of 15% dark colour tiles for patten of same

41 Providing and laying 900 mm x 900 mm Double 125.00 Sqmt 1876.78

charged 10 mm thick Vitrified tiles in Skirting laid on

10 mm thick cement mortar 1:3 ( 1 cement : 3 coarse

sand) and jointed with white cement slurry with

matching pigments including cleaning etc. complete

for all floors as directed by Architect or Engineer in

chage.(including cost of 15% dark colour tiles for

patten of same material)

42 Providing and laying 600 mm x 600 mm Double 533.00 Sqmt 1260.08

charged 10 mm thick Vitrified tiles in flooring laid on

20 mm thick cement mortar 1:6 (1 cement : 6 coarse

sand) on new surface and jointed with coloured

cement slurry including finished with flush pointing &

cleaning the surfaceetc complete for all floors as

directed by Architect or Engineer in chage. (including

cost of 15% dark colour tiles for patten of same

43 Providing and laying 600mm x 600mm Double 45.00 Sqmt 1364.31

charged 10 mm thick Vitrified tiles in Skirting laid on

10 mm thick cement mortar 1:3 ( 1 cement : 3 coarse

sand) and jointed with white cement slurry with

matching pigments including cleaning etc. complete

for all floors as directed by Architect or Engineer in

chage.(including cost of 15% dark colour tiles for

patten of same material)

44 Providing and laying Matt Finished Porcelene tiles 336.50 Sqmt 1091.96

60x60cm size 10 mm thick in flooring treads of steps

and landing laid on a bed of 12 mm thick cement

mortar 1:3(1-cement:3-coarse sand)finishing with

flush pointing in white cement

45 Providing and laying glazed tiles tiles size 30 x 60 cm 579.00 Sqmt 1549.31

8 mm thick in skirting risers of steps and dedo on

mm thick cement plaster 1:3 (1-cement:3coarse sand)

and jointed with colour cement slurry etc completed.

46 Providing and laying 600 mm x 600 mm Double 78.50 Sqmt 1297.55

charged 10 mm thick GVT Matt finished Vitrified tiles

in flooring laid on 20 mm thick cement mortar 1:6 (1

cement : 6 coarse sand) on new surface and jointed

with coloured cement slurry including finished with

flush pointing & cleaning the surfaceetc complete for

all floors as directed by Architect or Engineer in chage.

(including cost of 15% dark colour tiles for patten of

same material)

47 Providing and laying 600mm x 1200mm x 6 mm thick 303.00 Sqmt 1464.40

GVT Vitrified tiles in Skirting laid on 10 mm thick

cement mortar 1:3 ( 1 cement : 3 coarse sand) and

jointed with white cement slurry with matching

pigments including cleaning etc. complete for all floors

as directed by Architect or Engineer in

chage.(including cost of 15% dark colour tiles for

patten of same material)

48 Providing and laying machine cut free edge machine 89.00 Sqmt 3333.00

polished granite stone 18mm thick finished treads

and risers in with 1cm projecting, nozing rounded

moulding in tread, laid over 12 mm (av.) thick bases of

cement mortar 1:6 (1-cement : 6-coarse sand) for

treads and cement mortar 1:3 (1-cement : 3-coarse

sand) for riser jointed with grey or colour cement

slurry including rubbing and polishing incl. making

Three No.s of grooves of size 3mm X 3mm along the

length of treads etc. complete

49 Providing and fixing 16mm to 18mm Granite shelves 35.00 Sqmt 2225.03

or partition with Dhar polish on exposed edges,

including all accessories,Fitting and labor charges

directed by the engineering in charge, etc. complete

50 Providing and fixing mirror polished 16mm to 18 mm 421.00 Sqmt 3993.54

thick Granite stone with full round edge and polished

of approved quality in clading on sill and around the

doors/ windows/ ventilation with 12 mm thick

cement mortor CM (1 Cement :3 Fine Sand) and fixing

with cement slurry & adhesive including moulding of

exposed edges as directed by engineering in charge

etc. complete.

51 Providing and laying water proofing treatment by 217.00 Sqmt 988.68

conventional method including cleaning the slab

surface by wire brush as directed including provding

first layer of C.M. 1:4 of 40 mm thickness mixed with

water proofing compound at rate prescribed by

manufacturer, including putting of brick bats of

average thickness 40 mm Well immerssed in water

laid uniformly on first layer of mortar including

applying cement slurry @ rate of 0.08 bag/sqm. on

fixed layer of brick bats including maintaining

necessary slope, in second layer 40 mm thick C.M 1:4

mixed with water proofing compound as directed,

including finishing smooth with cement slurry as

directed complete.

52 Providing and fixing M.S Safty Grills having 16mm 159.00 Sqmt 3829.92

Solid MS Squre or round bar Horizontally at every

equal 0.10m C/C distance and 2 no of bar Vertically at

every equal 0.375m C/C distance Fixing on around

(5x40) mm Solid MS Patti including cutting, welding

and fabrication etc; including one coat of primer of

approved quality and two coats of oil painting as per

detail drawing etc. complete as per directed Engineer

in charge.

53 Providing erecting and fixing double coated PVC. (ISI) 20000.00 Litre 3.95

water tank of required capacity each with all

necessary fittings and connection etc. complete on

54 Providing laying and jointing in true line and level 420.00 Rmt 195.67

50mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water

including fittings as approved by Engineer In Charge.

Pipe shall be fixed on the wall with the help of clamp

at every two metre C/C or shall be concelled as

directed including necessary fittings etc. including

testing of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials.

55 Providing laying and jointing in true line and level 440.00 Rmt 148.12

40mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water

including fittings as approved by Engineer In Charge.

Pipe shall be fixed on the wall with the help of clamp

at every two metre C/C or shall be concelled as

directed including necessary fittings etc. including

testing of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials.

56 Providing laying and jointing in true line and level 480.00 Rmt 91.84

25mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water

including fittings as approved by Engineer In Charge.

Pipe shall be fixed on the wall with the help of clamp

at every two metre C/C or shall be concelled as

directed including necessary fittings etc. including

testing of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials.

57 Providing laying and jointing in true line and level 320.00 Rmt 72.65

15mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water

including fittings as approved by Engineer In Charge.

Pipe shall be fixed on the wall with the help of clamp

at every two metre C/C or shall be concelled as

directed including necessary fittings etc. including

testing of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials.

58 Providing, laying and jointing in true line and level 160 300.00 Rmt 834.38

diametre U.P.V.C (Type B) conforming to IS 13592-

1992 with one end plain and other end socketed with

rubber ring, & fittings conforming to ISI 14735-1999

of approved make for drainage system pipe line, pipe

shall be jointed with each other with rubber lubricant,

pipe shall be fixed on wall using of PVC clamp of the

size 160 mm diametre x 210 mm length x 196 mm

heigh at every 2000 mm center to center or shall be

concealed in walls as directed including necessary

fittings such as bends, shoes etc. including testing of

pipes and joints and jointed with adhesive solvent

cement including cost of all materials.

59 Providing, laying and jointing in true line and level 110 296.00 Rmt 899.49

diametre U.P.V.C (Type B) conforming to IS 13592-

1992 with one end plain and other end socketed with

rubber ring, & fittings conforming to ISI 14735-1999

of approved make for drainage system pipe line, pipe

shall be jointed with each other with rubber lubricant,

pipe shall be fixed on wall using of PVC clamp of the

size 110 mm diametre x 149 mm length x 145 mm

heigh at every 2000 mm center to center or shall be

concealed in walls as directed including necessary

fittings such as bends, shoes etc. including testing of

pipes and joints and jointed with adhesive solvent

cement including cost of all materials.

60 Providing, laying and jointing in true line and level 75 100.00 Rmt 286.84

mm dia. UPVC SWRType B pipe conforming to IS

13592-1992 with one end plain and other end

socketed with rubbering and fitting conforming to ISI

14735-1999 of approved make for drainage system

pipe line, pipe shall be jointed with each other with

rubber lubricant, pipe shall be fixed on wall using of

PVC clamp at every 2000 mm c/c or shall be conceled

in walss as directed including necessary fittings such

as bends, shoes etc. including testing of pipes and

joints and jointed with adhesive solvent cement

including cost of all materials.

61 Providing and fixing in PVC SWR cowel went 75mm 10.00 No 16.16

dia to pipes.(B) 75mm dia.

62 Providing and fixing in PVC SWR cowel went 110mm 12.00 No 29.29

dia to pipes.(B) 110mm dia.

63 Providing and fixing PVC non-return fullway wheel 30.00 No 389.86

valve (A) 25mm dia.

64 Providing and fixing PVC non-return fullway wheel 30.00 No 570.65

valve (A) 40mm dia.

65 Providing and fixing PVC SWR Nahni trap IS 14735 for 26.00 No 571.08

drain - 100 mm diameter with jali of the following

nominal diameter of self cleansing design with C.I

scread down or hinged grating including the cost of

cutting and making good the walls.

66 Providing and fixing Tankless Wall Hung WC with 26.00 No 29212.23

Sensor Flush, model ONS-WHT-10961BIUFSMTL or

Jaquar standard company, of size 380 x 625 x 385 mm,

complete with UF soft-close slim seat cover, hinges,

concealed flush system, suitable wall frame support

system ( Jaquar ), exposed part kit of concealed stop

cock & flush cock (model KUP-35083KPM or

equivalent), health faucet (model ALD-577 or

equivalent) with 8 mm dia, 1 meter long flexible tube,

wall hook and N.R.V. (backflow preventer), including

all required fittings, accessories, connection materials,

testing and installation complete as per

manufacturer’s specifications and as directed by the

Engineer-in-Charge.

67 Providing and fixing Soap Dispenser with Glass Bottle, 31.00 No 1590.75

model ACN-1135N, of Jaquar standard company,

complete with all required fittings, mounting

accessories, and installation, as per manufacturer’s

specifications and as directed by the Engineer-in-

68 Providing and fixing stainless steel grab 22 cm x 60 cm 8.00 No 1492.78

on door and handicapped toilet including all fixture

and accessary etc completed as per directed engineer

in charge.

69 Providing and fixing ball cock of approved. quality as 4.00 No 189.84

directed.(A) Copper Metal (ii) 50mm dia.

70 Providing and fixing Thin Rim Table Top Basin, model 32.00 No 12585.61

JDS-WHT-25909, of Jaquar rectangular shape, size

495 x 395 x 150 mm, complete with Pillar Cock with

extension body (model FLP-5021PM), Exposed Part

Kit of Concealed Stop Cock with fitting sleeve,

operating lever and adjustable wall flange with seal

(model ARI-39083K), Polyamide braided connection

pipe 12 mm dia and 450 mm length, Waste coupling

32 mm size half thread with 80 mm height (model

ALD-709), and 32 mm dia waste pipe, including all

required fittings, accessories, jointing materials,

testing, and labour charges, complete as per

manufacturer’s specifications and as directed by the

Engineer-in-Charge.

71 Providing and fixing Swivel Mirror, model ACN-1185, 32.00 No 1033.74

of Jaquar or equivalent standard company, oval shape

of size 615 x 445 mm, complete with all required

fittings, fixtures, and installation, as per

manufacturer’s specifications and as directed by the

Engineer-in-Charge.

72 Providing and fixing Towel Ring (Round) with Round 32.00 No 1393.80

Flange, model ACN-1121BN, of Jaquar company,

complete with all required fittings, fixtures, screws,

and installation, as per manufacturer’s specifications

and as directed by the Engineer-in-Charge.

73 Providing and fixing Bib Cock with Wall Flange, model 58.00 No 2555.30

FUS-29037, of Jaquar or equivalent standard company,

complete with all required fittings, fixtures, screws,

and installation, as per manufacturer’s specifications

and as directed by the Engineer-in-Charge.

74 Providing and fixing Bathroom Accessories of Jaquar 26.00 No 8072.93

standard company, consisting of Soap Dish Holder

(model ACN-1131N), Towel Rack 600 mm long

without lower hangers but with 3 hooks, stainless

steel (model CN-1181FHS), Tumbler Holder (model

ACN-1141N), Double Coat Hook (model AQN-7761),

and Toilet Roll Holder (model ACN-1151N), complete

with all required fittings, fixtures, screws, and

installation, as per manufacturer’s specifications and

as directed by the Engineer-in-Charge.

75 Providing and fixing Urinal with Fixing Accessories, 1.00 No 5691.35

model URS-WHT-13261, of Jaquar standard company,

size 355 x 340 x 535 mm, complete with Exposed Part

Kit of Concealed Stop Cock with fitting sleeve,

operating lever and adjustable wall flange with seal

(model ARI-39083K), including all required fittings,

accessories, connection materials, testing and

installation, complete as per manufacturer’s

specifications and as directed by the Engineer-in-

76 Providing laying and jointing in true line and level 340.00 Rmt 1127.16

200mm dia. Form core Pipe for drainage including

fittings as approved by Engineer In Charge. Pipe shall

be fixed on existing structure, Wall or ground with

the help of clamp or shall be concelled as directed

including necessary fittings etc. including testing of

pipe and joints and fixing the same with adhesive

solvent, including cost of all materials.

77 Providing and fixing S.W. gully trap with C.I. grating 12.00 No 1246.92

brick masonry chamber and water tight C.I. cover with

frame of 300mm x 300mm size (inside) with standard

weight (i) Square mouth traps (B) 150mm x 100mm

size P or R type

78 Constructing brick masonry chamber for underground 20.00 No 3223.92

C.I. Inspection chamber and bends with briocks having

croshing strength not less than 35Kg. Cm2 in C.M. 1:5

precast RCC cover 455mm x 610mm intenal

dimensions with frame (R.C.C. top slabe with 1:2:4 mix

(1-cement :2- coarse sand :4-graded stone aggregate

20mm size) foundation concrete 1:5:10 inside plaster

15mm thick with cement mortar 1:3 finished smooth

with a floating coat of neat cement on walls and bed

concrete etc. complete (i) Inside dimensions 455mmx

610mm and 450mm deep for single pipe line.

79 Constructing brick masonry chamber for underground 20.00 No 3933.95

C.I. Inspection C.I. Inspection chamber and bends with

briocks having croshing strength not less than 35Kg.

Cm2 in C.M. 1:5 precast RCC cover 500mmx 700mm

intenal dimensions with frame (R.C.C. top slabe with

1:2:4 mix (1-cement :2- coarse sand :4-graded stone

aggregate 20mm size) foundation concrete 1:5:10

inside plaster 15mm thick with cement mortar 1:3

finished smooth with a floating coat of neat cement on

walls and bed concrete etc. complete (i) Inside

dimensions 500mmx 700mm and 450mm deep for

single pipe line.

80 Extra over items for every additional depth of 0.1M. of 10.00 No 242.39

part thereof beyond 450mm depth for Brick masonry

chamber.(i) for 455mm x 610mm size.

81 Extra over items for every additional depth of 0.1M. of 10.00 No 264.86

part thereof beyond 450mm depth for Brick masonry

chamber.(i) for 500mm x 700mm size.

82 Providing and fixing MS Ladder of required pattern 3300.00 Kg 99.99

with MS flats(30x3mm) or round or square bars

(12mm) at required spacing & with round headed

bolts and nuts or screws or welding including primer

coat of approved quality and two coats of oil paintas as

directed by engineer in charge

83 Providing and fixing 60 cm Height granite stone 29.00 Sqmt 7878.20

platform for table top wash basin made from 18 mm

thick granite stone of approved make, colour and

quality, fixed horizontally on the wall with necessary

supports and brackets as per site condition. The work

shall include providing front facia patti and moulded

top front edge, vertical granite end supports on both

sides, proper leveling and alignment, edge polishing,

grinding, and smooth finishing. The platform shall be

fixed in position with cement mortar (1:3) and cement

slurry to ensure firm bonding, including making

necessary cutouts and openings for the table top wash

basin, fittings, and plumbing lines as per detailed

drawing. All exposed edges shall be machine polished

to give a mirror finish. The work shall be completed in

all respects as per standard specification and as

directed by the Engineer-in-Charge.

84 Providing and fixing Kitchen sink with C.I. or M.S. 2.00 No 5193.42

brackets, painted white including cutting holes in

walls and making good the same but excluding fittings.

(C) Vitreous China Sink.(i) 600mm x 450mm x 150mm

size including pillar cock 15mm, M.I fisher union

32mm, C.P Brass waste 32mm , Angle cock 15mm

including all laboure and material charges etc.

completed.

85 Providing and fixing kitchen platform trolley having 9.00 Sqmt 14213.73

three drawers of SS (IS 304) of required size like thali,

katleri, perforated, partition, cupsosar type in kitchen

platform having drawer front side and backside by

using 19mm thick all proof plywood of ISI quality all

side laminated etc. as directed. The size of SS (IS 304)

basket of size 4" to 18" for thali, dish, katleri,

perforated, partition, cupsosar type as directed

including necessary S.S. fittings, handles, nobs,

telescopic channels, etc. as directed

86 Providing and fixing in position 300 mm high, 150 mm 75.00 No 1333.20

wide English letters made from 1.0 mm thick stainless

steel sheet as directed by Engineer in charge with all

necessary tools & plants etc. complete.

87 Providing and fixing in position 150 mm high, English 75.00 No 686.80

letters made from 1.0 mm thick stainless steel sheet as

directed by Engineer in charge with all necessary tools

& plants etc. complete.

88 Providing and Fixing a set of wall mounted 38 mm dia 2.00 No 2671.45

U shaped horizontal stainless steel collapsible grab bar

, 38mm vertical stainless steel fixed grab rail of grade

SS 304 from round pipe supported and 75 mm dia

mm thick SS 304 base flange on wall including anchor

fasteners, nuts, accessories as per detailed drawing

etc. complete as directed by Architect or Engineer in

89 Providing and fixing MS Z clamp on Wall or celling for 467.00 No 85.85

Pipe Fitting including all type necessary fittings and

accessory etc. completed as per directed engineer in

90 Charges for making holes from 50mm to 160 mm dia 30.00 No 858.50

in RCC wall, slabs or any other RCC members or Brick

work by diamond core cutting machine of HILTI or

equivalent including disposing the debris. For all

91 Providing and fixing coloured self adhesive PU-Tactile 18.00 Sqmt 4586.41

tile, ground surface indicators of Polyurethane) of size

300mm x 300mm for guiding/warning to the visually

visitors in the centre/side of the pedestrian/approach

pathway as per specification and guidelines complete

in all respect to the entire satisfaction of in charge.

92 Providing and fixing acrylic multilingual Braille 20.00 No 1696.80

(raised dots) DIRECTIONAL SIGNBOARDS of size 225 x

150mm designed as per accessibility standards and

having 3.5mm thick acrylic base plate with Upper Case

San Serif words made of white acrylic non glare cut

out letters of height 15mm raised not less than 0.8mm

above base plate and the equivalent word written in

Hindi with Devanagari non glare acrylic letters of

height 15mm raised not less than 0.8mm above base

plate and having a non-glare acrylic cut arrow pointing

in the required direction. Each signboard to be fixed as

per manufacturers specifications on the wall at the

approved location and at a height of 1200mm from

FFL complete as per design / specifications and

guidelines as per the entire satisfaction of the Engineer-

93 Providing & Fixing tactile layout plan of size 900mm x 1.00 Nos 33027.00

600mm as approved design, made of 3.0mm thick

acrylic non glare base plate and non glare cut out

symbols with Braille on which individual facility

points, like inquiry, reception, restrooms, medical

room / first aid, cafeteria or breakout area, lounge,

meeting room, conference room etc. present the

respective floors with pictograph wherever needed all

in tactile raised by minimum of 1.0mm to 2mm in

various colours to make it legible for seniors, partial

vision impaired etc. All the facility names should be in

Braille, along with English or Hindi. The entire block of

tactile signs should be mounted on wall for easy

reading. The map to be installed at specified locations

and installed at a height of 800mm from ground level

complete in all respect as per Harmonized guideline &

satisfaction of Engineer in charges.

94 Providing and fixing of acrylic, non-glare, tactile audio 1.00 Nos 50298.00

pictorial building layout as per the approved size,

design and make, having 3mm thick acrylic non glare

base plate of the approved colour and non-glare

acrylic cut out symbols raised 3mm above base plate

and Grade 2/ Grade 1 Braille to be integral with the

sign face and be raised 0.5mm above base plate. The

map to be installed at the specified location as per

accessibility standards, shall be oriented to the

position of the viewer and to be installed at a height of

800 mm from the finished ground/ floor level and

using the necessary hardware specified by the

manufacturer and to be installed up to the height of

800 mm from the finished ground/ floor level and

using the necessary hardware specified by the

manufacturer and to be installed complete as per

design/specifications and guidelines as per the entire

satisfaction of the the Engineer-in-charge

95 P& F BRAILE INDICATOR OF SIZE 170 MM X 35MM 20.00 Rmt 820.12

FOR HANDRAILS OF THE APPROVED DESIGN AND

MAKE HAVE BRAILE DOTS RAISED 0.5 MM ABOVE

BASE PLATE TO BE INSTALLED AT SPECIFIC

LOCATIONS AS PER DIRECTION OF ENGINEER IN

96 Providing and fixing of conspectus tape 50mm width 15.00 Rmt 1247.35

on of treads in staircase including cutting pasting etc.

As per harmonised guidelines complete in all respect

to the entire satisfaction of engineer in charge.

97 Providing and Fixing 15 mm thick 300 mm x 300 mm 1155.00 Sqmt 1357.44

Tactile Warning Tiles (Attention Tiles i.e. Tactile

Warning Surface Indicator {TWSI}) of Johnsan Endura

Tac Button Yellow Plus or equvqlent make in flooring

laid on 20 mm thick cement mortar 1:6 (1 cement :

coarse sand) on new surface and jointed with cement

slurry including finished with flush pointing &

cleaning the surface for all floors as per detailed

drawing etc. complete as directed by Architect or

Engineer in charge. Thse tiles shall be Anti Skid,

Chemical Resistant, Fade Proof, Frost - Heat &

Weather Proof, High Flexural Strength, Highly Durable,

Stain Resistance . All Tactile Warning Tiles meet the

specific size and dimension standards as required by

ISO/FDIS

98 Providing and fixing M.S Pipe fabrication For duct 111.60 Sqmt 2397.74

made from M.S pipe of 40 mm dia fitted into M.S

Frame with clamp into RCC/Brick structure at 0.10 m

c/c at equal distance fixed including all required

accessories as per detailed drawing as directed etc.

complete. for All Floor

99 Providing, designing, fabricating, and welding work for 164.30 Sqmt 560.55

temporary barricading using built-up sections framed

with 50mm x 50mm x 4mm steel poles, placed

vertically every 2.5m with poles embedded in the

ground in 0.3m x 0.3m x 0.45m deep pockets filled

with M150 cement concrete. Two horizontal poles will

be installed in each span. The structure will include GI

sheets of 3.1m height, made from pre-coated steel with

a minimum grade of 240 MPa, conforming to IS

14246:1995. These sheets must have a zinc coating of

at least 120 gsm as per IS 277:1992, with 5-7 microns

of epoxy primer on both sides and a polyester top coat

of 15-18 microns, along with a protective plastic guard

film of 25 microns to prevent scratches during

transportation. The ridge shall be fixed to steel

members using pop rivets or self-drilling/self-

stitching fasteners at a maximum spacing of 450mm

c/c. A priming coat of red lead paint and two coats of

oil paint will be applied to the entire frame. Upon

completion of the task, the barricading must be

dismantled, and the surface should be cleaned by the

construction agency, as per the instructions of the

Engineer-in-Charge.

100 Providing and Installing a 32mm diameter rock 455.00 No 1617.01

anchor, involving drilling a 40mm diameter hole to a

depth of 2 meters, placing a 32mm diameter steel

anchor rod (2 meters in length), and securing it with

cement-based grout (approximately 3 kg per anchor).

The rate includes all drilling consumables, such as drill

bits, and is carried out by a skilled drilling crew. . The

rate covers all labor, materials, equipment, and

overheads, as directed by the Engineer-in-Charge.

101 Excavation for foundation for depth from 3.0 m to 5.0 35.00 Cumt 307.16

m including sorting out and stacking of useful

materials and disposing off the excavated stuff upto

Meter lead.(C) Hard Murrum

102 Providing and fixing C.I. Manhole cover 0.60 M. x 2.00 Nos 958.17

0.45M. size having weight not less than 35Kg.

103 Providing and laying polished Kota stone slab flooring 75.00 Sqmt 1019.39

over 20mm (Average) thick base of cement mortar 1:6

(1-cement : 6-coarse sand) or L.M. 1.1.5 (1-Lime putty

:1.5 - coarse sand) laid over and jointed with grey

cement slurry mixed with pigment to match the shade

slab including rubbing and polishing etc. complete. (A)

25mm thick

104 Providing and laying polished kota stone slab 25mm 6.00 Sqmt 1173.09

thick in risers of steps,skirting Dedo and pillars laid on

10mm thick cement mortar 1:3 (1-Cement : 3 coarse

sand) and jointed with gray cement slury mixed with

pigment to match the shade of slab including rubbing

and polishing etc. complete.

105 Wall Painting (Two coats) with 100% acraylic 192.00 Sqmt 122.14

emulsion paint of approved brand and manufacture

and of required shade on exterior wall surface to give

an even shade over and including primery coat with

Alkaly resistance primer of approved brand after

thoroughly brushing surface to remove all dust and

remains of loose powdered material etc. copm. for all

106 Providing and fixing rolling shutters of approved make 10.00 Sqmt 3554.40

made of 80 mm wide M.S laths inter-locked together

through heir entire length and jointed together at the

ends by end locks mounted on specially designed pipe

shaft with bracket plates,guide channels and

arrangement for inside and outside locking with push-

pull operation including the cost of hood cover and

sprig etc.complete(A) Shutters having width below

107 Providing and fixing mirror polished 18 mm thick 5.00 Sqmt 3993.54

Green Marble stone with full round edge and polished

of approved quality in clading on sill and around the

doors/ windows/ ventilation with 12 mm thick

cement mortor CM (1:4) and fixing with cement slurry

& adhesive including moulding of exposed edges as

directed by engineering in charge etc. complete.

108 Drilling of min. 250 mm dia. bore hole in all strata 130.00 Rmt 1138.27

including dualover burden strata by combination

DR/DTH rig including lowering 200 mm dia MS ERW

pipes in bore hole and testing etc.all work as per

directed engineer incharge.

109 Manufacture, supply and delivery of cage 80.00 Rmt 1682.66

typeTrapezoidal shape ( ' V ') wire wound low carbon,

Galvanized screen pipe and Stainless Steel Screen

pipes, confirming IS: 8110 For (B) 200mm dia 1)

1.00mm Slot size

110 Bore plug having 100 mm height made from M.S. plate 1.00 No. 1161.62

with 3 holes at equal distance on circumference for

nut-bolts type, locking arrangement with nuts-bolts &

lock nuts of std. Make complete. For 250mm dia

111 Providing PVC insulated flat submersible cable as per 80.00 Rmt 180.79

detailed technical specifications of R/C of GWSSB

conforming to IS 694, IEC 60227 / 60228.d)1 R x 3 C x

112 Supplying of single phase submersible pump set 1.00 Set 18079.00

suitable for 100 mm size or more dia bore well having

motor capacity and discharge as under with necessary

panel box (c) Motor rating 2 HP (17 stage) pump

having capacity of 106 LPM at 40 mtr head suitable for

32 mm dia. delivery pipe

113 Supplying and erecting Direct On-line Electronics 1.00 No. 1727.10

Starter with 2-5/4-10/8-14/10-16 Amp. Rating relay

(variable current setting) directly operated in totally

insulated elegant enclosure and 18 Amp. Rating power

relay with start - stop button for single phase

operation up to 3 HP as per complete erected on P.W.

Block with following features. Low voltage cut off

below 140 V High voltage cut off above 280 V

Overload protection Indicating LEDs for motor on lv,

hv & overload tripping. [Cat.II]

114 Providing and fixing check or non return pully wheel 1.00 No. 1111.00

valve of 50 mm diameter.

115 Manufacture, supply and delivery of following ISI 80.00 Rmt 123.19

marked HDPE pipes (IS:4984/1985 with latest

amendment) having material Grade PE-80 in

approximate 100 meter coil length or as per GWSSB

requirement with SS 316 nipple at both ends having

11 TPI threads as per specifications, press fitted and

bolted having nominal diameter as under as per

detailed technical specifications. DN 50 PN-10

including oading of HDPE pipe coil of following size

into truck OR unloading and stacking the same in sub

divisional store as directed. Dia 50mm

116 Constructing brick masonry chamber for underground 10.00 No. 7180.44

C.I. Inspection chamber and bends with briocks having

croshing strength not less than 35Kg. Cm2 in C.M. 1:5

C.I. cover with frame (Light duty) 455mm x 610mm

intenal dimensions, total weight of cover with frame to

be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of

frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-

cement :2- coarse sand :4-graded stone aggregate

20mm size) foundation concrete 1:5:10 inside plaster

15mm thick with cement mortar 1:3 finished smooth

with a floating coat of neat cement on walls and bed

concrete etc. complete.(iii) Inside dimensions 600mm

x 850 mm and 450mm deep for pipe lines with three

or more inlets.

117 Providing laying (to level or slopes) and jointing 242.00 Rmt. 678.03

reinforced concrete Light duty non-pressure pipes I.S.

class NP2 of the following internal diameter with

collars and butt ends prepared for collar joints

including testing of joints complete.(D) 300mm

118 Providing and fixing and floor 10.0 Kg. F/Cm2 200.00 Rmt 339.05

working pressure poluthene pipes of the following

outside Dia. Low densidy, complete with special falnge

compression type fittings, wall clipsetc. including

making good the wall ceiling and floor.(G)110 mm

119 Providing and fixing and floor 10.0 Kg. F/Cm2 20.00 Rmt 696.90

working pressure poluthene pipes of the following

outside Dia. Low densidy, complete with special falnge

compression type fittings, wall clipsetc. including

making good the wall ceiling and floor.(G)180 mm

120 Providing junction for rain water juncton chamber of 6.00 Nos. 9484.91

size 0.60x0.60x0.75m with excavation of size

1.96x1.96 m & 0.15m thick c.c.1:2:4 bed concrete

including brick masonary wall in CM 1:6 of 0.75m

height & 0.23m thick with 15mm thick cement plaster

inside & outside & 1.06x1.06 RCC (1:2:4) slab of

thickness 0.15m with CRS steel and 0.60mx0.45m cast

iron manhole cover with frame weight not less than

kg as per directed by Engineer-in-charge

121 Providing and installation Recharge pit of “RAIWOHA” 1.00 Nos. 109645.60

Make 3 layer RCC Precast Injection well system of size

1.5 meter Dia. X 3.4 Meter Height rein forced concrete

precast three layer module with 6” dia x 12” dia. V

wire screen of 0.75mm x 1.0 mm Slot size in SS

material and 1.0 meter height with MS Top cover and

required Air vent including all necessary excavation

and transportation at site including required filter

media for the recharge system as per site requirement.

122 Supplying slotted PVC pipes of approved quality at site 50.00 Rmt 555.50

of work confirming to IS. 1239/1974 180mm dia.

123 Cleaning & maintenance of system Including all 1.00 Nos. 4646.00

Labour and replacing of Filter Media as Required for

124 Construction of granular sub-base 150 mm thick by 344.50 Cum 1222.14

providing coarse graded machine crushed B.T.

material satisfying MOST specification of grading I

(B.T. stone aggregate 53 mm to 26.5 mm 35 %, 26.5 to

4.75 mm - 45 % and 2.36 mm below - 20 % )including

spreading in uniform layer with motor grader on

prepared surface, mixing by mix in place method with

rotavator at OMC and compacting with vibratory roller

to achieve the desired density etc. complete.

125 Steel work, welded in built up sections framed work 57626.00 kg 91.08

including cutting, hoisting, fixing in position and

applying a priming coat of read lead paint & two coat

oil paint. (A)In beams and joists, channels angles Tees,

flats, with connecting plates or angle cleats as in main

and cross beams. Hip and jack rafters, purlins

conneted to common rafters and the like..

126 Providing and fixing of Ridge flashing for roof panel 1168.00 Sqmt 867.39

shall be made out of 0.5 mm thick pre coated GI sheet .

The Precoated sheet shall be of minimum 240 mpa

steel grade confirming to IS 14246:1995 and shall

have zinc coating of minimum 120 gsm as per

IS:277:1992 , 5-7 microns epoxy primer on both side

of the sheet and polyester top coat 15-18 micron. The

PPGI Sheet shall have plastic protective guard film of

minimum 25 microns to avoid scratches during

transportation. The ridge shall be fixed to the steel

members by pop rivet or self drilling/self stitching

fastners @ maximum 450 mm c/c along length of

capping/flashing etc complete .

127 Providing and fixing pre-cast concrete kerb stone of 698.00 Rmt 374.92

gray cement based concrete block 30cm ength,30cm

height and 15cm thick of M250 grade concret as per

approved design and including excavation for fixing in

proper line and level,filling the joint with C:M 1:3

(1cement:3fine sand) etc complete.

128 Box cutting the road surface to proper slope and 1016.00 Cum. 112.02

camber for making a base for road work including

removing the excavated stuff and depositing on the

road side slope as directed upto upto All lift and lead..

129 Providing, laying and compacting natural sand & 141.00 Cum. 422.18

gravel[ C.B.R. not less than 20%] below sub base

course including carriage of materials spreading in

uniform layer manually on prepared base and

compacted with vibratory roller to achieve desired

density including all materials, labour etc. complete.

130 Providing and laying wet mix macadam base course 351.00 Cum. 1274.62

250 mm thick in two layers using machine crushed

B.T. chips as per required gradation mixing with

required optimum quantity of water, conveying the

mix to site of work, spreading in to grade and camber

with mechanical paver and consolidation each layer

with vibratory roller including cost of material labour

plant and equipment etc. complete.

131 Compaction and finishing of cement concrete road by 1337.00 Sqm 65.65

trimix process providing extra Labour charges for the

trimix vacume dewatering service process on cement

concrete road sutface by using vacuum dewatering

pump floater surface vibrator including making groves

and rough finish to surface including leveling etc

132 Demolition including stacking of serviceable materilas 19.00 Cumt 1137.19

and disposal of unserviceable materials with all lead

and lift. (i) R.C.C. work

133 Demolition of Brick work and stone masonry including 49.00 Cumt 591.68

stacking of serviceable materilas and disposal of

unserviceable materials with all lead and lift.(ii) In

Cement Mortar.

134 Constructing providing and fabricating cattle guard 27.00 Sqmt 5194.43

using channel section frame of size ISMC series

mm x 50 mm (Weight 9.20 kg/Rmt) and ISMC section

100 mm x 75mm (weight 11.50 kg/Rmt) intermediate

support for welding G.I.pipe at 12 Cm C/C of size

mm in a frame made of Channel section size 100 mm x

50 mm all round including fixing the unit on prepared

chamber of masonary wall using MS hold fast

embeded in masonary wall top as directed by Engineer

in charge and as per drawing and necessary required

arrangement etc complete.

135 Providing and fixing decorative entrance gate made 2363.00 kg 183.82

out of cast iron and various mild steel tabular section

combination , the Ornamental entrance gate should be

fixed at compound wall including pattern and die

making , cutting , welding , grinding, fabrication , fixing

in position at compound wall with necessary pedestal,

bearing block and other locking arrangement. The

entrance gate should be painted with two coats of

priming coat of paint, and two coat of oil paint etc

complete. As per detail design and instruction of

architect.

136 Providing and fixing concertina coil fencing with 375.00 Rmt 864.56

punched tape concertina coil 600 mm dia 10 mt

openable length having 50 no rounds per 6 mt length,

upto 3mt height of wall with existing angle iron

(50mm x50mm x5mm )requird shaped As per

Directed Engeenier in charge. placed 2.4mt or 3.00mt

apart and with 4 horizontal R.B.T. reinforced barbed

wire(3 mm) , stud tied with G.I. staples and G.I. clips to

retain horizontal, including necessary bolts or

G.I.barbed wire tied to angle iron, all complete as per

direction of Engineer-in-charge, with reinforced

barbed tape (R.B.T.)/Spring core (2.5 mm thick) and

weight 43.478 gm/meter at compound wall for ESR

M4/ intakewell.

137 Providing and filter media 600mm thick as directed at 35.00 Sqm 1342.40

the back of Protection Wall as per detailed

specification.

138 Earthwork in cuting in all sorts of soil and soft 116.77 cu.m. 96.11

murrum including conveying and spreading the stuff,

embankment as and where directed within 200meters

from the end of the cutting with all required lead and

lift.(C) Above 400 Meters upto 500 Meters.

139 Earthwork for embankment including breaking clods, 5639.25 Cum 169.28

dressing with all lead and lift (excluding watering and

consolidation)(E) From Borrow area within 3.0 Km.

140 Rolling of Earth work in layers with power roller and 5756.02 Cum 23.10

watering including filling in depressions which occure

during the process.

141 Supply. installation, testing &commissioning of ISI 1.00 No 98424.50

approved electrical motor driven jockey pump set

having 10.8 m3/hr. @ 70m head.The pump unit shall

be a horizontally direct mounted motor. Unit shall

comprise the following minimum requirements:

a)Pump, b) Electric motor IE2, c) Foundation bolts, d)

Mating flanges with gasket and fasteners, e) Discharge

gauges, etc.complete in all respect, with labour.

142 Supply, installation, testing &commissioning of 1.00 No 25674.20

Priming tank, HDPE type, 1000 litres, with necessary

piping 100 mm size, G.I pipe for priming the pumps,

pipe of with butterfly valves for isolation, Water Filling

to priming tank by piping min. 50 mm size, with all

143 Supply, installation, testing &commissioning of 1.00 No 55630.80

Manifold( surge vessel,)for fire hydrant system,

min.300 mm diameter,made from M.S plate,hydro

tested to 15 kg./cm2. with ball valves,header with

couplings for fitting pressure switches,pressure

gauges etc.with necessary isolation valves with all

144 Supply, fabrication & erection of aboveground G.I. 'C'- 360.00 Mtr 393.90

Class, ERW piping,conforming to IS:1239, part-I, Heavy

class up to 150 mm dia. and IS:3589, for size 200 mm

dia. & above, thickness. G.I. pipe fitting's as per IS:

1239, part-II, Heavy class for size 150 mm dia. & below

& IS: 3589, for size 200 mm dia. above, flanges, nuts

bolts & washers, 3 mm thick gasket, pipe hangers,

etc.Hydrostatic testing for 2 hour's at 150% of the

system pressure, hook-up etc.

Painting for piping, fittings & structural pipe support,

shall be two coat of zinc primer and two coats of fire

red conf. to IS: 5, Shade 536. Complete with all

accessories as per approved drawings, specicification

and direction of the Engineer-in-Charge, with all

complete. 25 mm dia.

145 Supply, fabrication & erection of aboveground G.I. 'C'- 390.00 Mtr 636.30

Class, ERW piping, conforming to IS:1239, part-I,

Heavy class up to 150 mm dia. and IS:3589, for size

200 mm dia. & above, thickness. G.I. pipe fitting's as

per IS: 1239, part-II, Heavy class for size 150 mm dia.

& below & IS: 3589, for size 200 mm dia. above,

flanges, nuts bolts & washers, 3 mm thick gasket, pipe

hangers, etc.Hydrostatic testing for 2 hour's at 150%

of the system pressure, hook-up etc.

Painting for piping, fittings & structural pipe support,

shall be two coat of zinc primer and two coats of fire

red conf. to IS: 5, Shade 536. Complete with all

accessories as per approved drawings, specicification

and direction of the Engineer-in-Charge, with all

complete. 50 mm dia.

146 Supply, fabrication & erection of aboveground G.I. 'C'- 150.00 Mtr 1171.60

Class, ERW piping, conforming to IS:1239, part-I,

Heavy class up to 150 mm dia. and IS:3589, for size

200 mm dia. & above, thickness. G.I. pipe fitting's as

per IS: 1239, part-II, Heavy class for size 150 mm dia.

& below & IS: 3589, for size 200 mm dia. above,

flanges, nuts bolts & washers, 3 mm thick gasket, pipe

hangers, etc.Hydrostatic testing for 2 hour's at 150%

of the system pressure, hook-up etc.

Painting for piping, fittings & structural pipe support,

shall be two coat of zinc primer and two coats of fire

red conf. to IS: 5, Shade 536. Complete with all

accessories as per approved drawings, specicification

and direction of the Engineer-in-Charge, with all

complete. 80 mm dia.

147 Supply, fabrication & erection of aboveground G.I. 'C'- 360.00 Mtr 1686.70

Class, ERW piping, conforming to IS:1239, part-I,

Heavy class up to 150 mm dia. and IS:3589, for size

200 mm dia. & above, thickness. G.I. pipe fitting's as

per IS: 1239, part-II, Heavy class for size 150 mm dia.

& below & IS: 3589, for size 200 mm dia. above,

flanges, nuts bolts & washers, 3 mm thick gasket, pipe

hangers, etc.Hydrostatic testing for 2 hour's at 150%

of the system pressure, hook-up etc.

Painting for piping, fittings & structural pipe support,

shall be two coat of zinc primer and two coats of fire

red conf. to IS: 5, Shade 536. Complete with all

accessories as per approved drawings, specicification

and direction of the Engineer-in-Charge, with all

complete. 100 mm dia.

148 Supply, fabrication & erection of aboveground G.I. 'C'- 90.00 Mtr 2525.00

Class, ERW piping, conforming to IS:1239, part-I,

Heavy class up to 150 mm dia. and IS:3589, for size

200 mm dia. & above, thickness. G.I. pipe fitting's as

per IS: 1239, part-II, Heavy class for size 150 mm dia.

& below & IS: 3589, for size 200 mm dia. above,

flanges, nuts bolts & washers, 3 mm thick gasket, pipe

hangers, etc.Hydrostatic testing for 2 hour's at 150%

of the system pressure, hook-up etc.

Painting for piping, fittings & structural pipe support,

shall be two coat of zinc primer and two coats of fire

red conf. to IS: 5, Shade 536. Complete with all

accessories as per approved drawings, specicification

and direction of the Engineer-in-Charge, with all

complete. 150 mm dia.

149 Supply, fabrication & erection of aboveground G.I. 'C'- 7.00 Mtr 3413.80

Class, ERW piping, conforming to IS:1239, part-I,

Heavy class up to 150 mm dia. and IS:3589, for size

200 mm dia. & above, thickness. G.I. pipe fitting's as

per IS: 1239, part-II, Heavy class for size 150 mm dia.

& below & IS: 3589, for size 200 mm dia. above,

flanges, nuts bolts & washers, 3 mm thick gasket, pipe

hangers, etc.Hydrostatic testing for 2 hour's at 150%

of the system pressure, hook-up etc.

Painting for piping, fittings & structural pipe support,

shall be two coat of zinc primer and two coats of fire

red conf. to IS: 5, Shade 536. Complete with all

accessories as per approved drawings, specicification

and direction of the Engineer-in-Charge, with all

complete.200 mm dia.

150 Supply, installtion, testing & commissioing of 20.00 Mtr 2020.00

Underground GI (ERW) piping conforming to IS:1239,

part-I, Heavy class ('C' class) up to 150 mm dia. and

IS:3589 Heavy class ('C' class), for 200 mm dia. &

above, min. 6.35mm thickness including Heavy class

fittings, anti-corrosive tape of size 150 mm wide x

mm thick, wrapping & coating with 13KV holiday

testing . Rates shall include sand bedding of 75mm dia

all around, backfilling of the excavated including

installation of heavy pipe fitting's, flanges, etc. 10 % of

all the welded joints shall be done radiographically

tested and 50% of the joints radiographed shall be the

"Field Joints". Hydrostatic testing for 2 hours at 150%

of the system pressure, hook-up etc., complete with all

accessories as per approved drawings, specicification

and direction of the Engineer-in-Charge, with all

complete. (Road Crossing) 100 mm dia.

151 Supply, installtion, testing & commissioing of 10.00 Mtr 3040.10

Underground GI (ERW) piping conforming to IS:1239,

part-I, Heavy class ('C' class) up to 150 mm dia. and

IS:3589 Heavy class ('C' class), for 200 mm dia. &

above, min. 6.35mm thickness including Heavy class

fittings, anti-corrosive tape of size 150 mm wide x

mm thick, wrapping & coating with 13KV holiday

testing . Rates shall include sand bedding of 75mm dia

all around, backfilling of the excavated including

installation of heavy pipe fitting's, flanges, etc. 10 % of

all the welded joints shall be done radiographically

tested and 50% of the joints radiographed shall be the

"Field Joints". Hydrostatic testing for 2 hours at 150%

of the system pressure, hook-up etc., complete with all

accessories as per approved drawings, specicification

and direction of the Engineer-in-Charge, with all

complete. (Road Crossing) 150 mm dia.

152 Design , Supply and installation of Safety Signage made 14400.00 Sq. 9.09

of Zinc Sulphilde based glow in dark , Rigid sheet with inch

High Luminous property enclosed in a transperent

weather proof UV stabilized plastic pasted on 3 mm

thick clear acrylic sheet such as EXITS, EMERGENCY

EXIT, DO NOT USE LIFT DURING FIRE, FLOOR

MARKINGS, FIRE LIFT, STAIRCASE EXIT, FIRE ALARM

CALL POINT, FIRE HOSE REEL, FIRE HYDRANT POINT

153 Supply, Installtion, Testing & Commissioing of 150.00 No 555.50

Standard Response Sprinkler, Pendent Brass

Sprinkler, Quartzoid Bulb type with crome finish,

nickel crome platde, K factor K-80, Temp.- 680C, 1/2"

end connection including resessed escutcheon. (UL

154 Supply, installation, testing & commissioning of 3.00 No 2817.90

pressure switch. (Range 0 to 16 kg/cm2)

155 Supply, installation, testing & commissioning of 150 6.00 No 2737.10

mm dia. dial Burdon Type Glycerine Filled pressure

gauge with isolation ball valve arrangements with

necessary isolation valves with all complete.( Range

156 Supply, installation, testing & commissioning of Cast 2.00 No 5898.40

iron body double flanged gate valve With Rising

Spinldle conf. to IS: 14846, PN-1.6 with mating flanges,

drilling as per IS/ANSI 150# with mating flanges,

galvanized nut, bolts & washers, gasket 3 mm thick,

etc., with all complete. 50 mm dia.

157 Supply, installation, testing & commissioning of Cast 2.00 No 8181.00

iron body double flanged gate valve With Rising

Spinldle conf. to IS: 14846, PN-1.6 with mating flanges,

drilling as per IS/ANSI 150# with mating flanges,

galvanized nut, bolts & washers, gasket 3 mm thick,

etc., with all complete. 80 mm dia.

158 Supply, installation, testing & commissioning of Cast 2.00 No 10261.60

iron body double flanged gate valve With Rising

Spinldle conf. to IS: 14846, PN-1.6 with mating flanges,

drilling as per IS/ANSI 150# with mating flanges,

galvanized nut, bolts & washers, gasket 3 mm thick,

etc., with all complete. 100 mm dia.

159 Supply, installation, testing & commissioning of Cast 2.00 No 15917.60

iron body double flanged gate valve With Rising

Spinldle conf. to IS: 14846, PN-1.6 with mating flanges,

drilling as per IS/ANSI 150# with mating flanges,

galvanized nut, bolts & washers, gasket 3 mm thick,

etc., with all complete. 150 mm dia.

160 Supply, Installation, Testing & Commissioning of Cast 8.00 No 2009.90

iron body Butterfly valve according to IS: 13095, PN-

1.6, Iron Disc for size 150 mm dia. & below Lever

operated and above 150 mm dia. Gear operated

complete with mating flanges /ANSI class # 150 with

bolts & nuts washers, rubber gaskets 3 mm thick, etc.,

with all complete. 50 mm dia.

161 Supply, Installation, Testing & Commissioning of Cast 4.00 No 2565.40

iron body Butterfly valve according to IS: 13095, PN-

1.6, Iron Disc for size 150 mm dia. & below Lever

operated and above 150 mm dia. Gear operated

complete with mating flanges /ANSI class # 150 with

bolts & nuts washers, rubber gaskets 3 mm thick, etc.,

with all complete. 80 mm dia.

162 Supply, Installation, Testing & Commissioning of Cast 6.00 No 3120.90

iron body Butterfly valve according to IS: 13095, PN-

1.6, Iron Disc for size 150 mm dia. & below Lever

operated and above 150 mm dia. Gear operated

complete with mating flanges /ANSI class # 150 with

bolts & nuts washers, rubber gaskets 3 mm thick, etc.,

with all complete. 100 mm dia.

163 Supply, Installation, Testing & Commissioning of Cast 2.00 No 4484.40

iron body Butterfly valve according to IS: 13095, PN-

1.6, Iron Disc for size 150 mm dia. & below Lever

operated and above 150 mm dia. Gear operated

complete with mating flanges /ANSI class # 150 with

bolts & nuts washers, rubber gaskets 3 mm thick, etc.,

with all complete. 150 mm dia.

164 Supply, installation, testing & commissioning of Cast 2.00 No 1535.20

iron body Dual Plate Wafer Type NRV conf. to IS:

PN-1.6 complete with mating Flanges class # 150 with

bolts & nuts, washers, gaskets 3 mm thick, etc., with all

complete Accessories 50 mm dia.

165 Supply, installation, testing & commissioning of Cast 2.00 No 2222.00

iron body Dual Plate Wafer Type NRV conf. to IS:

PN-1.6 complete with mating Flanges class # 150 with

bolts & nuts, washers, gaskets 3 mm thick, etc., with all

complete Accessories 80 mm dia.

166 Supply, installation, testing & commissioning of Cast 2.00 No 3161.30

iron body Dual Plate Wafer Type NRV conf. to IS:

PN-1.6 complete with mating Flanges class # 150 with

bolts & nuts, washers, gaskets 3 mm thick, etc., with all

complete Accessories 100 mm dia.

167 Supply, installation, testing & commissioning of Cast 1.00 No 5817.60

iron body Dual Plate Wafer Type NRV conf. to IS:

PN-1.6 complete with mating Flanges class # 150 with

bolts & nuts, washers, gaskets 3 mm thick, etc., with all

complete Accessories 150 mm dia.

168 Supply, installation, testing & commissioning of SG 1.00 No 1111.00

iron body SinglePlate Wafer Type NRV conf. to ASTMA

536, PN-1.6 complete with mating Flanges class #

with bolts & nuts, washers, gaskets 3 mm thick, etc.,

with all complete. Accessories 50 mm dia.

169 Supply, installation, testing & commissioning of SG 1.00 No 1454.40

iron body SinglePlate Wafer Type NRV conf. to ASTMA

536, PN-1.6 complete with mating Flanges class #

with bolts & nuts, washers, gaskets 3 mm thick, etc.,

with all complete. Accessories 80 mm dia.

170 Supply, installation, testing & commissioning of SG 1.00 No 1787.70

iron body SinglePlate Wafer Type NRV conf. to ASTMA

536, PN-1.6 complete with mating Flanges class #

with bolts & nuts, washers, gaskets 3 mm thick, etc.,

with all complete. Accessories 100 mm dia.

171 Supply, installation, testing & commissioning of Y 2.00 No 5555.00

Type Strainer complete with mating flanges with bolts

& nuts, washers, gaskets 3 mm thick, etc., with all

complete accessories. 80 mm dia.

172 Supply, installation, testing & commissioning of Y 2.00 No 7272.00

Type Strainer complete with mating flanges with bolts

& nuts, washers, gaskets 3 mm thick, etc., with all

complete accessories. 100 mm dia.

173 Supply, installation, testing & commissioning of Y 2.00 No 11554.40

Type Strainer complete with mating flanges with bolts

& nuts, washers, gaskets 3 mm thick, etc., with all

complete accessories. 150 mm dia.

174 Supply, installing, testing and commissioning of 1.00 No 4191.50

Normax make CI heavy duty ball type foot valve with

flanges, nut bolts, gaskets etc. with necessary complete

accessories. 80 mm dia.

175 Supply, installing, testing and commissioning of 1.00 No 6161.00

Normax make CI heavy duty ball type foot valve with

flanges, nut bolts, gaskets etc. with necessary complete

accessories. 100 mm dia.

176 Supply, installing, testing and commissioning of 2.00 No 12402.80

Normax make CI heavy duty ball type foot valve with

flanges, nut bolts, gaskets etc. with necessary complete

accessories. 150 mm dia.

177 Supply, installation, testing & commissioning of Four 1.00 No 8978.90

way fire brigade Inlet connection with 63 mm dia.

stainless steel (SS304) instantaneous male inlets with

built in non return valve in each inlet with 150 mm

dia. header pipe, suitable rubber cap and GI chain

including nuts, bolts, washers, gasket 3 mm thick, etc.

with all complete.

178 Supply, installation, testing & commissioning of Two 1.00 No 5130.80

way fire brigade Inlet connection with 63 mm dia.

stainless steel (SS304) instantaneous male inlets with

built in non return valve in each inlet with 100 mm

dia. header pipe, suitable rubber cap and GI chain

including nuts, bolts, washers, gasket 3 mm thick, etc.

with all complete.

179 Supplying FIRE bucket round bottom of 9 liters 8.00 No 1020.10

capacity made out of 24 gauge G.I Sheet with extra

handle at bottom duly painted white inside and Red

out side with FIRE mark. Filled with dry-sand and kept

on existing stand provided or hung on wall hook.

180 Supplying and erecting floor mounting Stand for 2.00 No 5555.00

keeping four nos. of FIRE buckets comprising

mm in length, 900 mm height frame made out of

30mm x 30 mm x 4 mm angle iron with cross supports

legs, welded with 4 hooks and duly painted with one

coat of primer and two coats of approved enamel P O

red paint.

181 Supply & installation of stainless steel body Orifice 10.00 No 1060.50

Plate of suitable inner bore along with matching flange

- as per specification & requirement as per hydraulic

calculation.

182 Providing and fixing approved make Perforated C type 10.00 Mtr 464.60

cable tray. Made from pre- galvanized sheet steel. The

cable tray should be bended as per IS 2062/1079 .

with max 17.5% perforation with coupler plate / Fish

plate and GI hardware like nut - bolt and washers etc.

erected on existing support as per Specification and as

per instruction of engineer in charge..(5) 300 X 50 X

1.5 mm Thick

183 Providing and fixing approved make Perforated C type 10.00 Mtr 313.10

cable tray. Made from pre- galvanized sheet steel. The

cable tray should be bended as per IS 2062/1079 .

with max 17.5% perforation with coupler plate / Fish

plate and GI hardware like nut - bolt and washers etc.

erected on existing support as per Specification and as

per instruction of engineer in charge..(3) 150 X 50 X

1.5 mm Thick

184 Supply, installation, testing & commissioning of 10.00 No 5433.80

Oblique pattern type stainless steel (SS 304) single

headed External Fire Hydrant Valve with 63 mm dia.

female instantaneous outlet conf. to IS: 5290, type - A,

including mating flanges, galvanised nuts, galvanised

bolts/studs, washers & gaskets 3 mm thick with all

185 Supply, installation, testing & commissioning of 63 mm 10.00 No 1747.30

dia. stainless steel (SS 304) Universal Branch Pipe

conf. to IS:

186 Supply & installation, testing & commissioing of Fire 10.00 No 6958.90

Fighting Hose - conf. to IS : 636, type B (type- 3), The

fire hose shall be 15 m long with 63 mm dia. stainless

steel (SS 304) couplings conf. to IS: 903, at both the

ends for connection with the hydrant valve and the

branch pipe.

187 Supply, installation, testing & commissioning of 10.00 No 2525.00

fabricated from 3 mm MS sheet, hose box of size-450

mm x 600 mm x 250 mm - painted with Fire Red as

per IS: 5, shade no. 536 front 3 mm thick transparent

glass with lock & key, handle and brass hinges - to

accommodate one number of 15 mtr long hose and

one number of universal branch pipe, including

supporting arrangement with civil work.

188 Supply, Installation, testing & commissioing of 10.00 No 7403.30

Swinging type mild steel hose reel drum with 20 mm

dia. x 30 mtr. rubber hose as per IS: 884. The mounting

stand shall be of mild steel and the hose shall be fitted

with a SS shut-off nozzle & SS ball valve of 25 mm dia.

including supporting arrangement with all complete.

accessories

189 Supplying, fixing & testing of of CI ball Valve 25mm 30.00 No 696.90

dia. (Thread)

190 Supplying, fixing & testing of New Battery of diesel 1.00 No 15826.70

engine 150 Amp.

191 Supply and installation of Diesel Tank For Diesel 1.00 No 16685.20

Engine With All Accessories 100 Ltrs.

192 Supplying, filling & testing lube oil for diesel engine 15.00 Ltrs 313.10

193 Supply and commissioning of Oil Filter. 1.00 No 696.90

194 Supplying, filling of diesel in diesel engine tank 80.00 Ltrs 89.87

195 Supply and commissioning of Diesel Filter 1.00 No 427.97

196 Supplying, filling & testing coolant to engine cooling 20.00 Ltrs 239.66

for radiator

197 Filling Of Gaps Between pipe and Core Cutting Hole 150.00 No 299.58

With Chemical and Cement

198 Supplying & erecting XLPE(IS:7098)(I)-88 ISI 50.00 Mtr 136.35

unarmoured copper cable 1.1 KV grade to be erected

as directed of following size. (E) 3 core 2.5 Sq. mm for

pressure switch

199 Providing and erecting XLPE(IS:7098)(I)-88 ISI 50.00 Mtr 285.83

armoured cable multistrand Copper conductor for

KV. to be laid on wall with necessary clamps or in

existing trench / pipe at road crossing or floor of

following size of cable. (Only Fire Panel to Fire Pump)

(B) 3 core 4 Sq. mm

200 Providing and erecting XLPE(IS:7098)(I)-88 ISI 40.00 Mtr 497.93

armoured cable multistrand Copper conductor for

KV. to be laid on wall with necessary clamps or in

existing trench / pipe at road crossing or floor of

following size of cable. (Only Fire Panel to Fire Pump)

(D) 3 core 10 Sq. mm (Only Fire Panel to Fire Pump)

201 Providing and erecting XLPE(IS:7098)(I)-88 ISI 40.00 Mtr 213.11

armoured cable multistrand Copper conductor for

KV. to be laid on wall with necessary clamps or in

existing trench / pipe at road crossing or floor of

following size of cable for Diesel Engine Battery

Charger (A) 3 core 2.5Sq. mm

202 Supply, Filling and Fixing of approved make ABC type 20.00 No 1959.40

fire extinguisher - 6 Kg. Capacity as per IS:15683 & IS :

203 Supply, Filling and Fixing of approved make CO2 type 20.00 No 5514.60

fire extinguisher. Capacity 4.5 Kg. (conforming to IS-

204 Supply, Filling and Fixing of approved make ABC 6.00 No 3413.80

Moduler type automatic fire extinguisher. Capacity

Kg. (conforming to IS-15683).

205 Submitting the application to obtain Fire Plan 1.00 No 252500.00

Approval and After Completion of Work Obtain Final

Fire NOC for 3 Year.

206 Supply, Installation and commissioning of Air Release 3.00 No 1403.90

Valve, 25 mm Dia. connection.

207 Supply, Installation and commissioning of Fire Alarm 2.00 No 21391.80

Panel Conventional type, 4 zone, with complete

accessories.

208 Supply, Installation and commissioning of smoke 100.00 No 1020.10

detectors / heat detectors, with complete accessories.

209 Supply, Installation and commissioning of plug in base 100.00 No 252.50

for the smoke detectors, hooters, with complete

accessories.

210 Supply, Installation and commissioning of Audio 10.00 No 1060.50

hooters , with complete accessories.

211 Supply, Installation and commissioning of Manual Call 10.00 No 1010.00

Points, with complete accessories.

212 Providing and erecting XLPE(IS:7098)(I)-88 ISI 2500.00 Mtr 176.75

armoured cable multistrand Copper conductor for

KV. to be laid on wall with necessary clamps or in

existing trench / pipe of following size of cables (A)

core 2.5 Sq. mm for Fire Alarm System

213 Core cutting in wall and in RCC slab with size as below: 100.00 No 333.30

50 mm dia. Hole

214 Core cutting in wall and in RCC slab with size as below: 20.00 No 424.20

80 mm dia. Hole

215 Core cutting in wall and in RCC slab with size as below: 10.00 No 505.00

100 mm dia. Hole

216 Core cutting in wall and in RCC slab with size as below: 10.00 No 595.90

150 mm dia. Hole

217 Core cutting in wall and in RCC slab with size as below: 10.00 No 848.40

200 mm dia.

218 Supply, installation, testing & commissioning of ISI 1.00 Set 176750.00

approved electrical motor operated Kirloskar make

fire hydrant main pump set horizontal end suction

back pull out top discharge centrifugal fire pump set

with all the standard acessories, base frame, coupling,

and foundation bolts with following specifications

Model -DB 80/26,

Flow-97 m3/hr,Head-70 meter,Motor Rating -

30KW/40HP/3 ph, Suc x Del - 80 x

219 Supplying, Installation, Testing and commissioning of 1.00 Set 388850.00

Kirloskar make diesel engine driven fire hydrant pump

set suitable for automatic operation and consisting of

following: horizontal type, centrifugal end suction

back pull out, top discharge pump of cast iron body &

bronze impeller with m.s.fabricated common base

plate, coupling, coupling guard, foundation bolts etc.,as

required. Model -KFE Flow-97 m3/hr,Head-70 meter,

Engine - 39 HP / 3 ph Suc x Del - 100 x

220 Fire Hydrant Panel suitable for 10 hp Jockey pump, 40 1.00 No 101000.00

hp (97 m3/hr @ 70 m head) main electrical pump and

39 hp (97 m3/hr @ 70 m head) Diesel engine operated

A) Incomer MCCB - 1 Nos R Y B Indication - 1 Set VAF

Digital Meter - 1 Set B) Outgoing F1 40 HP Star

Delta Starter - 1 For Main pump F2 10 HP DOL Starter -

1 For Jockey Pump F3 Auto - On / Off Diesel Pump

With Battery Charger Control Circuit With Auto -

Manual On/Off On/Off Trip Indication On/Off Push

Button C) Fabrication Dully Powder Coated PO Red

Colour,Fabricated From 14/16 SWG,GI Sheet , IP-42

Protection,-Fixed Type Floor Mounted

Cable Entry : Bottom

221 Pay Legal Fees to Concern Authority for Obtaining Plan 2600.00 Sq.mt 15.15

Approval and Final NOC

222 Point wiring for Light / Bell with 2-1.5 sq.mm & 399.00 Pt. 485.81

earth wire of 1.5 sq.mm (Green) both are of ISI marked

1.1 KV grade FRLS PVC insulated multi strand copper

wires up to 10 mtr length , in below type of pipe

erected with 6A Modular type switch / bell push &

accessories and earth continuity of following type,

erected on PVC / Metallic/Wooden box, single

mounting base frame covered with

textured/metallic/white front plate modules erected

on / in wall / ceiling as per pipe erected, with

necessary Lamp holder/ceiling rose / H.D.Connector

as directed.(f) with medium class Rigid PVC pipe and

accessories erected concealed in wall/ceiling

Cat. III (Make : Pipe: Precision /Polycab /nihir /astral,

Wire : havells ,finolex /polycab/ rr kabel/KEI ,Acc.

Legrand,GreatWhite Arcus ,Havells Crabtree,L&T

Englanze,mk Blanze)

223 Point wiring for Modular secondary light point with 2- 127.00 Pt. 167.66

1.5 sq.mm & earth wire of 1.5 sq.mm (green) both are

of ISI marked 1.1 KV grade FRLS PVC insulated multi

strand copper wires, in below type of pipe to be

erected complete with earth continuity and necessary

connection with primary light with accessories erected

on Metal / PVC / wooden box covered with 3 mm

thick PC(Polycarbonate) / Acrylic sheet for open /

concealed wiring. with necessary Lamp holder /

ceiling rose / H.D.Connector as directed.Note:-

Maximum up to 6 mtrs length, excess will be

considered as Mains for Secondary Point.

(f) with medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete (Make :

Pipe: Precision /Polycab /nihir /astral, Wire : havells

,finolex /polycab/ rr kabel/KEI ,Acc.

Legrand,GreatWhite Arcus ,Havells Crabtree,L&T

Englanze,mk Blanze)

224 Point wiring for Two Way Controlled Light Point with 68.00 Pt. 603.98

2-1.5 sq.mm & earth wire of 1.5 sq.mm (green) both

are of .ISI marked 1.1 KV grade FRLS PVC insulated

multi strand copper wires erected in below type of

pipe with 6A Modular type switches and following

type of accessories erected on PVC / Metallic/Wooden

box, single mounting base frame covered with

textured / metallic/white front plate modules erected

on / in wall / ceiling as per pipe erected. with

necessary batten/angle holder or ceiling rose or

H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete Cat III

(Make : Pipe: Precision /Polycab /nihir /astral, Wire :

havells ,finolex /polycab/ rr kabel/KEI ,Acc.

Legrand,GreatWhite Arcus ,Havells Crabtree,L&T

Englanze,mk Blanze)

225 Point wiring for FAN with 2-1.5 sq.mm & earth wire of 83.00 Pt. 674.68

1.5 sq.mm (Green) both are of .ISI marked 1.1 KV

Grade FRLS PVC insulated multi strand copper wires

up to 10 mtr length, in below type of pipe erected

with 6A Modular type switch and hum free EME step

type electronic fan regulator mounted and

accessories with earth continuity of following type

erected on PVC / Metallic/Wooden box, single

mounting base frame covered with

textured/metallic/white front plate modules erected

on / in wall / ceiling as per pipe erected. with

necessary ceiling rose / H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete

Cat. III (Make : Pipe: Precision /Polycab /nihir /astral,

Wire : havells ,finolex /polycab/ rr kabel/KEI ,Acc.

Legrand,GreatWhite Arcus ,Havells Crabtree,L&T

Englanze,mk Blanze)

226 Point wiring for on board Looped Plug with 6A 120.00 Pt. 257.55

Modular type switch & 5 pin socket erected on PVC /

Metallic/Wooden box, single mounting base frame

covered with textured / metallic/white front plate

modules erected on / in wall / ceiling with following

type accessories

Cat. III (Make : Pipe: Precision /Polycab /nihir /astral,

Wire : havells ,finolex /polycab/ rr kabel/KEI ,Acc.

Legrand,GreatWhite Arcus ,Havells Crabtree,L&T

Englanze,mk Blanze)

227 Providing following type of Modular Type Accessories 103.00 Ea. 151.50

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge.

(1)One No. SP 6 Amp.

Cat.III (Acc. Legrand,GreatWhite Arcus ,Havells

Crabtree,L&T Englanze,mk Blanze)

228 Providing following type of Modular Type Accessories 103.00 Ea. 151.50

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge.

(2) One No 5 pin plug

Cat.III (Acc. Legrand,GreatWhite Arcus ,Havells

Crabtree,L&T Englanze,mk Blanze)

229 Providing following type of Modular Type Accessories 37.00 Ea. 160.59

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (3) Two Pin/RJ-11 Telephone

Socket. [A] For One Gang

Cat.III (Acc. Legrand,GreatWhite Arcus ,Havells

Crabtree,L&T Englanze,mk Blanze)

230 Providing following type of Modular Type Accessories 263.00 Ea. 25.25

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge.

(7) Blank Plate Single

Cat.III (Acc. Legrand,GreatWhite Arcus ,Havells

Crabtree,L&T Englanze,mk Blanze)

231 Providing following type of Modular Type Accessories 52.00 Ea. 160.59

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge.

(8) Computer RJ-45 socket

Cat.III (Acc. Legrand,GreatWhite Arcus ,Havells

Crabtree,L&T Englanze,mk Blanze)

232 Providing following type of Modular Type Accessories 32.00 Ea. 160.59

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge.

(4) TV Co-axial Socket outlet

Cat.III (Acc. Legrand,GreatWhite Arcus ,Havells

Crabtree,L&T Englanze,mk Blanze)

233 Providing following type of Modular Type Accessories 66.00 Ea. 180.79

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge.

(9) 16 Amp. SP one way switch

Cat.III (Acc. Legrand,GreatWhite Arcus ,Havells

Crabtree,L&T Englanze,mk Blanze)

234 Providing following type of Modular Type Accessories 141.00 Ea. 199.98

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge.

(10) 6/16Amp. Universal socket

Cat.III (Acc. Legrand,GreatWhite Arcus ,Havells

Crabtree,L&T Englanze,mk Blanze)

235 Providing following type of Modular Type Accessories 51.00 Ea. 410.06

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge.

(14) 16A Double Pole Modular MCB Switch

Cat.III (Acc. Legrand,GreatWhite Arcus ,Havells

Crabtree,L&T Englanze,mk Blanze)

236 Providing following type of Modular Type Accessories 16.00 Ea. 360.57

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge.

(16) 32 Amp. DP Main Switch Operating with Energy

Cat.III (Acc. Legrand,GreatWhite Arcus ,Havells

Crabtree,L&T Englanze,mk Blanze)

237 Providing following type of Modular Type Accessories 22.00 Ea. 329.26

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge.

(19) Modular Indicating Call Bell

Cat.III (Acc. Legrand,GreatWhite Arcus ,Havells

Crabtree,L&T Englanze,mk Blanze)

238 Providing following type of Modular Type Accessories 24.00 Ea. 494.90

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge.

(21) Foot Light as per colour requirement with

concealed box, modular accessories, acrylic glass cover

with suitable LED watt with all accessories as per

following module

(b) Four modules

Cat-III (Make Philips,Havells,osram,Wipro)

239 Providing and erecting ISI mark Medium class RIGID 2495.00 Mtr. 24.24

PVC PIPES of following size complete to be erected

on/in wall or ceiling erected with necessary PVC

fittings & Junction boxes fixed with adhesive solution

& Clamps with following dia of pipes, in approved

manner as directed (a)20 mm (Make : Pipe: Precision

/Polycab /nihir /astral)

240 Supplying and laying UPVC cable trunking system 70.00 Mtr. 277.75

comprising unplasticised polyvinyl, chloride rigid

material with ignition free and flame proof confirming

BS with necessary end caps Internal and external

bend, flat bends, coupler, tee etc..All necessary

accessories and measuring of following sizes

(1) 75 mm x 50 mm trunking (Make : Pipe: Precision

/Polycab /nihir /astral)

241 Providing and fixing approved make Perforated C type 190.00 Rmt. 622.16

cable tray. Made from sheet steel. The cable tray

should be single or double bended as per required and

as per IS 2062/1079 and shall be coated with hot dip

galvanizing as per IS 2629/4759. with max 17.5%

perforation with coupler plate / Fish plate and GI

hardware like nut - bolt and washers etc. erection with

necessary support( included) as per Specification and

as per instruction of engineer in charge..

(5) 300 X 50 X 2.0 mm Thick

242 Providing and erecting Mains with 1.1 KV grade FRLS 4092.00 Mtr. 82.82

PVC insulated ISI marked stranded Copper conductor

wire in following type of pipe to be erected concealed

in /flushed on wall/ceiling, with 1.5 sq. mm copper

conductor FRLS PVC insulated stranded wire of green

colour for earth continuity of following size (A) With

medium class Rigid PVC pipe and accessories

(b) 2 wire 2.5 sq. mm (Make : Pipe: Precision /Polycab

/nihir /astral, Wire : havells ,finolex /polycab/ rr

kabel/KEI)

243 providing and erecting Mains with 1.1 KV grade FRLS 1275.00 Mtr. 112.11

PVC insulated ISI marked stranded Copper conductor

wire in following type of pipe to be erected in / on wall

/ ceiling with 2.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth

continuity of following size

(A) with medium class Rigid PVC pipe and accessories

(a) 2 wire 4 sq. mm (Make : Pipe: Precision /Polycab

/nihir /astral, Wire : havells ,finolex /polycab/ rr

kabel/KEI)

244 providing and erecting Mains with 1.1 KV grade FRLS 780.00 Mtr. 260.58

PVC insulated ISI marked stranded Copper conductor

wire in following type of pipe to be erected in / on wall

/ ceiling with 2.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth

continuity of following size

(A) with medium class Rigid PVC pipe and accessories

(h) 4 wire 6 sq. mm (Make : Pipe: Precision /Polycab

/nihir /astral, Wire : havells ,finolex /polycab/ rr

kabel/KEI)

245 providing and erecting Mains with ISI marked, 1.5KV 58.00 Mtr. 56.56

grade electrolyte multi stranded, annealed copper

conductor with heat resistant PVC insulated conforms

to IS 694, IEC - 227 erected in existing pipe of

following size (Specifically for control panel, relays,

power switchgears, motor starters & control wiring)

with required size of copper lugs, nuts and bolts if

(e) One wire 6.00 sq. mm (Wire : havells ,finolex

/polycab/ rr kabel/KEI)

246 providing and erecting Mains with ISI marked, 1.5KV 504.00 Mtr. 236.34

grade electrolyte multi stranded, annealed copper

conductor with heat resistant PVC insulated conforms

to IS 694, IEC - 227 erected in existing pipe of

following size (Specifically for control panel, relays,

power switchgears, motor starters & control wiring)

with required size of copper lugs, nuts and bolts if

247 Supplying and erecting Flexible PVC insulated multi 108.00 Mtr. 22.22

strand multi core 1.1 kv grade ISI marked copper

wires of following size to be erected as directed.

(c) 1.00 Sq.mm 2 core round/ flat PVC sheathed (Wire

: havells ,finolex /polycab/ rr kabel/KEI)

248 Supplying and erecting Flexible PVC insulated multi 92.00 Mtr. 46.46

strand multi core 1.1 kv grade ISI marked copper

wires of following size to be erected as directed.

(e) 1.50 Sq.mm 3 core round PVC sheathed (Wire :

havells ,finolex /polycab/ rr kabel/KEI)

249 Providing & Erecting approved make following size of 720.00 Mtr. 39.39

TV Co-axial flexible cable comprising inner conductor

of solid bare copper insulated with Foam PE &

Secondary conductor made of poly - Aluminium film

bonded Al. Braids @ suitable coverage overall

sheathed with black PVC insulation.

(b) RG-6 (Wire : havells ,finolex /polycab/ rr

kabel/KEI)

250 Supplying & erecting approved make Telephone Cable 120.00 Mtr. 199.98

electrolytic copper conductor PE insulation twisted in

two pairs, & wrapped with FRLS PVC tape & sheathed

with FRLS PVC or HFFR outer Jacket suitable for

telephone wiring & confirming to C-DOT erected in

existing pipe. of following size of conductors & nos.of

pairs. With necessary connections.

(b) Armoured [Jelly Filled]

(2) Twenty Pairs

251 Supplying & erecting approved make Telephone Cable 25.00 Mtr. 467.63

electrolytic copper conductor PE insulation twisted in

two pairs, & wrapped with FRLS PVC tape & sheathed

with FRLS PVC or HFFR outer Jacket suitable for

telephone wiring & confirming to C-DOT erected in

existing pipe. of following size of conductors & nos.of

pairs. With necessary connections.

(b) Armoured [Jelly Filled]

(3) Fifty Pairs

252 Supplying & erecting approved make Telephone Cable 20.00 Mtr. 875.67

electrolytic copper conductor PE insulation twisted in

two pairs, & wrapped with FRLS PVC tape & sheathed

with FRLS PVC or HFFR outer Jacket suitable for

telephone wiring & confirming to C-DOT erected in

existing pipe. of following size of conductors & nos.of

pairs. With necessary connections.

(b) Armoured [Jelly Filled]

(4) One Hundred Pairs

253 Supplying & erecting approved make LAN cable of 2080.00 Mtr 76.76

following size in existing pipe as per direction

[D] CAT - 6 e (Make Cable : D-link ,finolex /polycab /

rr kabel/KEI)

254 Providing & erecting main Distribution (MDF) indoor 6.00 Ea. 1368.55

type, back mounted frame as per DoT standard

approved with krone strips

(b) Suitable for 20 pair

255 Providing & erecting main Distribution (MDF) indoor 1.00 Ea. 1747.30

type, back mounted frame as per DoT standard

approved with krone strips

(c) Suitable for 50 pair

256 Providing & erecting main Distribution (MDF) indoor 1.00 Ea. 3443.09

type, back mounted frame as per DoT standard

approved with krone strips

(d) Suitable for 100 pair

257 Providing & erecting Switch board for Computer or 52.00 Ea. 1133.22

electric apparatus consisting of following modular

type accessories mounted with PVC / Metallic

concealed/open box with single mounting base frame

covered with textured/metallic /white front

plate,modules erected with necessary connections as

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug

For Modular Type Accessories

Cat. III (Make : Pipe: Precision /Polycab /nihir /astral,

Wire : havells ,finolex /polycab/ rr kabel/KEI ,Acc.

Legrand,GreatWhite Arcus ,Havells Crabtree,L&T

Englanze,mk Blanze)

258 Decorative call bell Ting-tong box type 250 volts 2.00 Ea. 71.71

complete erected (Make : Havells ,GM , Panosonic)

259 Supply & fixing decorative Hanging light with glass 8.00 Ea. 1797.80

having cylindrical or square shape having length not

less than 10" & width not less 3.5" with holder, lead

wire as per required length but not more than 1mm &

base plate for fixing the fitting with ceiling.[a] suitable

for led lamp Cat-III (Make

Philips,Havells,osram,Wipro)

260 Supplying and erecting LED indoor fittings with LEDs 32.00 Ea. 535.30

of wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be

made of thick sheet Steel conforming to IS: 513/CRCA/

aluminium die cast powder coated and high U.V. &

corrosion resistance with diffuser with company

mark/name 160V to 270V, Power Factor more than

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE:

Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may

(A) Tube Light with integral driver

(v) 36-40 Watts, Surge-2 KV, IP-20, conventional 4 feet

Cat-lll (Make Philips,Havells,osram)

261 Supplying and erecting LED indoor fittings with LEDs 369.00 Ea. 758.51

of wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be

made of thick sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast powder

coated and high U.V. & corrosion resistance with

diffuser housed in aluminium casted body with

company mark/name

160V to 270V,Power Factor more than 0.95, THD <

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE:

Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may

(A) Square/ Circular shaped Surface/Recessed Mount

Downlight with provision for spring loaded mounting

clips complete.IP20 (iv) 22-24 watts, Surge-2 KVCat-lll

(Make Philips,Havells,osram)

262 Supplying and erecting LED indoor fittings with LEDs 8.00 Ea. 1794.77

of wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be

made of thick sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast powder

coated and high U.V. & corrosion resistance with

diffuser housed in aluminium casted body with

company mark/name

160V to 270V,Power Factor more than 0.95, THD <

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE:

Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may

(B) LED Panel Light with provision for Plane front

frame with translucent cover fixed to housing

complete.IP20 (vi) 36 watts, 24" x 24", Surge- 2KV Cat-

lll (Make Philips,Havells,osram)

263 Supplying and erecting LED indoor fittings with LEDs 29.00 Ea. 312.09

of wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be

made of thick sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast powder

coated and high U.V. & corrosion resistance with

diffuser housed in aluminium casted body with

company mark/name

160V to 270V,Power Factor more than 0.95, THD <

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE:

Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may

(H) Mirror Light 9 Watts, wall mounted minimum

feet long (Make Philips,Havells,osram)

264 Supplying and erecting LED indoor fittings with LEDs 7.00 Ea. 966.57

of wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be

made of thick sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast powder

coated and high U.V. & corrosion resistance with

diffuser housed in aluminium casted body with

company mark/name

160V to 270V,Power Factor more than 0.95, THD <

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE:

Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may

(ii) 12 Watts Cat-lll (Make Philips,Havells,osram)

265 Supplying and erecting LED indoor fittings with LEDs 11.00 Ea. 1097.87

of wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be

made of thick sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast powder

coated and high U.V. & corrosion resistance with

diffuser housed in aluminium casted body with

company mark/name

160V to 270V,Power Factor more than 0.95, THD <

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE:

Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may

(iii) 15 Watts Cat-lll (Make Philips,Havells,osram)

266 Supplying & erecting approved make low noise 33.00 Ea. 1703.87

decorative exhaust fan having square frame ABS body

with inbuilt lowers & square frame.

200mm with 1350RPM Cat.II (Make

Crompton,bajaj,Havells,Orient).

267 Providing and erecting decorative wall bracket fittings 8.00 Ea. 1712.96

complete with LED lamp and rust free fittings

components mounted in chrome finish housing with

holder ,clear/opaque glass diffuser complete erected

with lead wires with minimum 15 wattage capacity as

per instruction engineer incharge/architect/authority

.cat-III (Make Philips,Havells,osram)

268 Supplying and erecting LED street light / Flood light 10.00 Ea. 4997.48

fittings with High power White LEDs wattage of 3 Watt

and above assembled on single MCPCB, efficiency

more than 130 lm/w and corrosion free High pressure

die cast aluminum housing with smooth finish powder

coated and heat sink extruded aluminium with

diffuser and Polycarbonate optics/ lenses, with

toughened glass with company mark/name engraved

or embossed 160 to 270 V,Power Factor more than

0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity

ratio >0.45, Luminaire efficacy> 100 lumens/watt .

LED driver efficiency > 85 %.( fittings required LM-79

& LM-80 certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED fittings.The

between the ranges shown.)

(A) Street Light (IP-65), Surge protection -4KV integral

and ,Light must have 440VAC line supply with over-

voltage protection.

(ii) above 48 to 60 Watts Cat-lll (Make

Philips,Havells,osram)

269 Supplying and erecting LED street light / Flood light 10.00 Ea. 4819.72

fittings with High power White LEDs wattage of 3 Watt

and above assembled on single MCPCB, efficiency

more than 130 lm/w and corrosion free High pressure

die cast aluminum housing with smooth finish powder

coated and heat sink extruded aluminium with

diffuser and Polycarbonate optics/ lenses, with

toughened glass with company mark/name engraved

or embossed 160 to 270 V,Power Factor more than

0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity

ratio >0.45, Luminaire efficacy> 100 lumens/watt .

LED driver efficiency > 85 %.( fittings required LM-79

& LM-80 certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED fittings.The

between the ranges shown.)

(C) Post Top Lantern LED fitting comprises of finish

cast aluminum spigot and spun aluminum canopy

fixed with opal polycarbonate, pipe arrangement for

vertical mounting driver and accessories wired upto

terminal block.IP 65(ii)32-40W Cat-lll (Make

Philips,Havells,osram)

270 Providing & erecting Approved make Ceiling Fan with 28.00 Ea. 2311.89

double ball bearing ISI mark with Condenser 230 volt

A.C.50 Hz 1200 mm sweep complete having 3 blades

aluminium body and blade sets having ornamental

design shanks , canopy erected with earthing. [ Make

shall be approved by Engineer in Charge] (Make

Crompton,bajaj,Havells,Orient).

271 Providing & erecting Approved make Ceiling Fan with 8.00 Ea. 1982.63

double ball bearing with Condenser 230 volt A.C.50

Hz. 900 mm sweep complete having 3 Aluminium

blades, canopy erected complete. [ Make shall be

approved by Engineer in Charge] (Make

Crompton,bajaj,Havells,Orient).

272 Providing & erecting Approved make Power Saving 50 47.00 Ea. 1948.29

Watt Ceiling Fan with double ball bearing ISI mark

with Condenser 230 volt A.C. 50 Hz 1200 mm sweep

complete having 3blades with aluminium blades with

, canopy & 30 cm. down rod erected with

earthing.(Make shall be approved by Engineer in

charge)) (Make Crompton,bajaj,Havells,Orient).

273 Supplying and erecting 19 / 20 mm. nominal bore 83.00 Mtr. 108.07

Medium Class M.S. Pipe down rod erected duly painted

for fan complete with proper insulation without

leakage and earthing.

274 Supplying & erecting fan hook box of 10 mm M.S. 83.00 Ea. 108.07

round bar bounded to the RCC bars up to 50mm length

each side and pierced through a 16 Gauge M.S. box /

Heavy Duty PVC box complete erected concealed in

Ceiling with necessary finishing.

275 Providing 2.5mm.thick laminated acrylic sheet to 83.00 Ea. 18.18

cover the fan hook or Fan box.

276 Providing and erecting XLPE(IS:7098)(I)-88 ISI 60.00 Mtr. 92.92

armoured cable Aluminium conductor for 1.1 KV. to

be laid on wall with necessary clamps or in existing

trench / pipe of following size of cables.

(B) 2 core 6 Sq. mm (Make: Havells ,KEI, L & T

,Polycab,RR Kabel)

277 Providing and erecting XLPE(IS:7098)(I)-88 ISI 34.00 Mtr. 378.75

armoured cable multistrand Aluminium conductor for

1.1 KV. to be laid on wall with necessary clamps or in

existing trench / pipe of following size of cables

(D) 3 1/2 core 70 Sq. mm ( 35 Sq. mm 1/2 core)

(Make: Havells ,KEI, L & T ,Polycab,RR Kabel)

278 Providing and erecting XLPE(IS:7098)(I)-88 ISI 204.00 Mtr. 540.35

armoured cable multistrand Aluminium conductor for

1.1 KV. to be laid on wall with necessary clamps or in

existing trench / pipe of following size of cables

(F) 3 1/2 core 120 Sq. mm ( 70 Sq. mm 1/2 core)

(Make: Havells ,KEI, L & T ,Polycab,RR Kabel)

279 Providing and erecting XLPE(IS:7098)(I)-88 ISI 170.00 Mtr. 904.96

armoured cable multistrand Aluminium conductor for

1.1 KV. to be laid on wall with necessary clamps or in

existing trench / pipe of following size of cables

(H) 3 1/2 core 185 Sq. mm ( 95 Sq. mm 1/2 core)

(Make: Havells ,KEI, L & T ,Polycab,RR Kabel)

280 Providing and erecting XLPE(IS:7098)(I)-88 ISI 110.00 Mtr. 1168.57

armoured cable multistrand Aluminium conductor for

1.1 KV. to be laid on wall with necessary clamps or in

existing trench / pipe of following size of cables

(I) 3 1/2 core 240 Sq. mm( 120 Sq. mm 1/2 core)

(Make: Havells ,KEI, L & T ,Polycab,RR Kabel)

281 Providing and erecting XLPE (IS:7098)(I)-88 ISI 370.00 Mtr. 126.25

armoured cable multistrand / Solid Aluminium

conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe of

following size of cables

(B) 4 core 6 Sq. mm (Make: Havells ,KEI, L & T

,Polycab,RR Kabel)

282 Providing and erecting XLPE (IS:7098)(I)-88 ISI 60.00 Mtr. 153.52

armoured cable multistrand Aluminium conductor for

1.1 KV. to be laid on wall with necessary clamps or in

existing trench / pipe of following size of cables

(A) 4 core 16 Sq. mm (Make: Havells ,KEI, L & T

,Polycab,RR Kabel)

283 Making trench in soft soil of suitable width of 90 cm 646.00 Mtr. 55.55

deep for laying cable or locating the fault all over the

run and back filling the same and making the surface

as normal ground.

284 Providing & laying. R.C.C. Hume pipe for cable to be 110.00 Mtr. 343.40

laid 90 cm. below ground across the road crossing or

on floor with necessary material in an approved

manner and making the ground as per original.

(C) 300 mm dia

285 Providing & laying approved make Double walled 296.00 Mtr. 62.62

corrugated pipes (DWC) of polyethylene(conforming

to IS 14930 II )with necessary connecting accessories

of same material at required depth in existing trench

for laying of cable. below ground / road surface for

enclosing cable

(A)50 mm outer dia (Make: Jemini,Rax,Duraline)

286 Providing & laying approved make Double walled 120.00 Mtr. 137.36

corrugated pipes (DWC) of polyethylene(conforming

to IS 14930 II )with necessary connecting accessories

of same material at required depth in existing trench

for laying of cable. below ground / road surface for

enclosing cable

(D)120 mm outer dia. (Make: Jemini,Rax,Duraline)

287 Providing and, fixing heavy duty flange type brass 9.00 Ea. 38.38

cable gland with rubber ring for PVC insulated

armoured cable complete with out going tails,

insulating tape etc for following size of cables.

(B) 2 to 4 core 6 Sq. mm

288 Providing and, fixing heavy duty flange type brass 2.00 Ea. 47.47

cable gland with rubber ring for PVC insulated

armoured cable complete with out going tails,

insulating tape etc for following size of cables.

(D) 2 to 4 core 16 Sq. mm

289 Providing and, fixing heavy duty flange type brass 4.00 Ea. 103.02

double compression type cable gland with rubber

ring for PVC insulated armoured cable complete with

out going tails, insulating tape etc for following size of

(C) 3 & 1/2 core 70 Sq. mm

290 Providing and, fixing heavy duty flange type brass 6.00 Ea. 140.39

double compression type cable gland with rubber

ring for PVC insulated armoured cable complete with

out going tails, insulating tape etc for following size of

(E) 3 & 1/2 core 120 Sq. mm

291 Providing and, fixing heavy duty flange type brass 2.00 Ea. 238.36

double compression type cable gland with rubber

ring for PVC insulated armoured cable complete with

out going tails, insulating tape etc for following size of

(G) 3 & 1/2 core 185 Sq. mm

292 Providing and, fixing heavy duty flange type brass 6.00 Ea. 247.45

double compression type cable gland with rubber

ring for PVC insulated armoured cable complete with

out going tails, insulating tape etc for following size of

(H) 3 & 1/2 core 240 Sq. mm

293 Solder less crimping type Aluminium lugs conforming 40.00 Ea. 6.06

to IS suitable for cable of following size evenly

crimped with high pressure tool & connected to

switchgear terminals with brass/cadmium plated nut

bolts in an approved manner.

294 Solder less crimping type Aluminium lugs conforming 16.00 Ea. 15.15

to IS suitable for cable of following size evenly

crimped with high pressure tool & connected to

switchgear terminals with brass/cadmium plated nut

bolts in an approved manner.

295 Solder less crimping type Aluminium lugs conforming 4.00 Ea. 20.20

to IS suitable for cable of following size evenly

crimped with high pressure tool & connected to

switchgear terminals with brass/cadmium plated nut

bolts in an approved manner.

296 Solder less crimping type Aluminium lugs conforming 18.00 Ea. 25.25

to IS suitable for cable of following size evenly

crimped with high pressure tool & connected to

switchgear terminals with brass/cadmium plated nut

bolts in an approved manner.

297 Solder less crimping type Aluminium lugs conforming 26.00 Ea. 45.45

to IS suitable for cable of following size evenly

crimped with high pressure tool & connected to

switchgear terminals with brass/cadmium plated nut

bolts in an approved manner.

298 Solder less crimping type Aluminium lugs conforming 6.00 Ea. 80.80

to IS suitable for cable of following size evenly

crimped with high pressure tool & connected to

switchgear terminals with brass/cadmium plated nut

bolts in an approved manner.

299 Solder less crimping type Aluminium lugs conforming 18.00 Ea. 85.85

to IS suitable for cable of following size evenly

crimped with high pressure tool & connected to

switchgear terminals with brass/cadmium plated nut

bolts in an approved manner.

300 Providing and erecting Approved make Four pole 42.00 Ea. 6173.12

moulded case circuit breaker having breaking capacity

ICU of 25 KA. at 415 V,having normal current rating up

to 25 A to 100A. with Fixed thermal & magnetic

release suitable to work on A.C. supply 50 c/s. with all

internal connections, spreader tinned copper &

complete erected in existing 16 G.M.S. housing.

ICS=100% of ICU only Cat III (make: havells , L &

T , Simens , legrand , ABB,Hager)

301 Providing and erecting Approved make Four pole 6.00 Ea. 16221.61

moulded case circuit breaker having breaking capacity

ICU of 35 KA. at 415 V. having Normal current rating

200A.with variable Thermal & magnetic release

suitable to work on A.C.supply 50 c/s. with all internal

connections, spreader tinned copper & complete

erected in existing 16 G.M.S.housing ICS=100% of

ICU only Cat III (make: havells , L & T , Simens

legrand , ABB,Hager)

302 Providing and erecting Approved make Four pole 5.00 Ea. 20946.39

moulded case circuit breaker having breaking capacity

ICU of 35 KA. and above at 415 V . having normal

current rating 250A. with variable thermal &

magnetic release suitable to work on A.C.supply

c/s. with all internal connections, spreader tinned

copper & complete erected in existing 16 G.M.S.

ICS=100% of ICU only Cat III (make: havells , L

& T , Simens , legrand , ABB,Hager)

303 Providing and erecting Approved make Four pole 6.00 Ea. 25228.79

moulded case circuit breaker having breaking capacity

ICU of 50 KA and above at 415 V having Normal

current rating 400A. with variable Thermal &

magnetic release suitable to work on A.C.supply

c/s. With all internal connections, spreader tinned

copper & complete erected in existing 16 G.M.S.

ICS=100% of ICU only Cat III (make: havells , L &

T , Simens , legrand , ABB,Hager)

304 Providing and erecting Approved make Four pole 3.00 Ea. 28173.95

moulded case circuit breaker having breaking capacity

ICU of 50 K.A. and above at 415 V having normal

current rating up to 630A. with variable thermal &

magnetic release suitable to work on A.C.supply

c/s. with all internal connections, spreader tinned

copper & complete erected in existing 16 G.M.S.

housing ICS=100% of ICU only Cat III (make:

havells , L & T , Simens , legrand , ABB,Hager)

305 Supplying & erecting approved make Four Pole 415V 1.00 Ea. 26149.91

change over switch interior for panel mounting with

operating mechanism A.C.23 duty confirming to IS for

Cat-lll (make: havells , L & T , Simens , legrand

ABB,Hager)

306 Supplying and erecting triple pole & neutral 440V / 2.40 Rn.Mt 3202.71

500V panel mounting Copper Busbars with four equal r

Nos. of electrolyte bus having current density not

more than 1.6 Amp. / sq.mm (Rated current / cross

section area) duly wrapped with colour insulating tape

for phase sequence of following current carrying

capacity, erected with necessary bus bar supports

/insulators, main cable socket to each bar, erected in

existing cubical panel with necessary connections.

(B) Suitable for 200 Amp. capacity

307 Supplying and erecting triple pole & neutral 440V / 2.40 Rn.Mt 4909.61

500V panel mounting Copper Busbars with four equal r

Nos. of electrolyte bus having current density not

more than 1.6 Amp. / sq.mm (Rated current / cross

section area) duly wrapped with colour insulating tape

for phase sequence of following current carrying

capacity, erected with necessary bus bar supports

/insulators, main cable socket to each bar, erected in

existing cubical panel with necessary connections.

(C) Suitable for 300 Amp. capacity

308 Supplying and erecting triple pole & neutral 440V / 3.30 Rn.Mt 7319.47

500V panel mounting Copper Busbars with four equal r

Nos. of electrolyte bus having current density not

more than 1.6 Amp. / sq.mm (Rated current / cross

section area) duly wrapped with colour insulating tape

for phase sequence of following current carrying

capacity, erected with necessary bus bar supports

/insulators, main cable socket to each bar, erected in

existing cubical panel with necessary connections.(D)

Suitable for 400 Amp. capacity

309 Supplying and erecting triple pole & neutral 440V / 1.80 Rn.Mt 10559.55

500V panel mounting Copper Busbars with four equal r

Nos. of electrolyte bus having current density not

more than 1.6 Amp. / sq.mm (Rated current / cross

section area) duly wrapped with colour insulating tape

for phase sequence of following current carrying

capacity, erected with necessary bus bar supports

/insulators, main cable socket to each bar, erected in

existing cubical panel with necessary connections.(E)

Suitable for 630 Amp. capacity

310 providing and erecting Miniature circuit breaker 332.00 Ea. 112.11

single pole 6A to 25A suitable to operate on 240 V A.C.

system and having breaking capacity 10 KA to be

erected in existing box. confirming to IS 8828/1996

with ISI Mark

Cat.III (make: havells,L & T ,Simens,legrand

,ABB,Hager)

311 Providing & erecting 240 V MCB double pole switch 2.00 Ea. 278.76

for lighting Load (B Curve) having 10 KA breaking

capacity & confirms to IS : 8828 in existing box having

following capacity

(A) 6 to 32 Amp. Cat.III (make: havells,L & T

,Simens,legrand ,ABB,Hager)

312 Providing & erecting 240 V MCB double pole switch 12.00 Ea. 295.93

for lighting Load (B Curve) having 10 KA breaking

capacity & confirms to IS : 8828 in existing box having

following capacity

(B) 40 Amp. Cat.III (make: havells,L & T

,Simens,legrand ,ABB,Hager)

313 providing and erecting Approved make RCCBs 9.00 Ea. 1969.50

conforming to IS: 12640 and having sensitivity of

mA and Short Circuit withstand capacity of 10 KA and

suitable for operation on single phase 240 V,50Hz.

having characteristic of quick action & tripping with

all advance feature & do not incorporate any electronic

component. for following Max. rating erected as

directed(i) 25 Amps.DP Cat. III (make: havells,L & T

,Simens,legrand ,ABB,Hager)

314 providing and erecting Approved make RCCBs 78.00 Ea. 2235.13

conforming to IS: 12640 and having sensitivity of

mA and Short Circuit withstand capacity of 10 KA and

suitable for operation on single phase 240 V,50Hz.

having characteristic of quick action & tripping with

all advance feature & do not incorporate any electronic

component. for following Max. rating erected as

(ii) 40Amps. DP Cat. III (make: havells,L & T

,Simens,legrand ,ABB,Hager)

315 Providing & erecting 415V MCB Four Pole Switch for 19.00 Ea. 638.32

Lighting Load (B curve) having 10KA breaking

capacity & confirms to IS :8828 in existing box having

following capacity

(b)40 Amp. Cat.III (make: havells,L & T

,Simens,legrand ,ABB,Hager)

316 Providing & erecting 415 V MCB Four Pole for Motor 13.00 Ea. 737.30

& Inductive Load (C Curve) having 10KA breaking

capacity & confirms to IS :8828 in existing box having

following capacity (c)63 Amp. Cat.III (make: havells,L

& T ,Simens,legrand ,ABB,Hager)

317 Sheets steel powder coated enclosure suitable for 7.00 Ea. 176.75

incorporating One/Two nos. MCB. (make: havells,L &

T ,Simens,legrand ,ABB,Hager)

318 Providing and erecting Sheet Steel powder coated MCB 2.00 Ea. 1492.78

distribution board - flush / surface mounted fitted

with busbar, neutral link, earth bar and DIN rail,

Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without

MCB to house appropriate nos. of MCBs.(The DBs

should be used of same company of MCB to be used)

suitable for (A) single phase incoming and horizontal

single phase outgoing

(b) sheet steel double door (IP-43) (iv)12 way (make:

havells,L & T ,Simens,legrand ,ABB,Hager)

319 Providing and erecting Sheet Steel powder coated MCB 26.00 Ea. 2339.16

distribution board - flush / surface mounted fitted

with busbar, neutral link, earth bar and DIN rail,

Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without

MCB to house appropriate nos. of MCBs.(The DBs

should be used of same company of MCB to be used)

suitable for

(B) three phase incoming and single phase horizontal

type outgoing Per phase isolation type (PPI)

(b) sheet steel double door (i)4 way (make: havells,L

& T ,Simens,legrand ,ABB,Hager)

320 Providing and erecting Annealed bare Copper wire 8 20.00 Kg. 794.87

to 16 SWG.

321 Providing and erecting HOT deep Galvanised iron strip 24.00 Kg. 77.77

wire 8 to 16 SWG.

322 Providing and erecting Pipe type earthing having 150 9.00 Ea. 368.65

cms.long and 2.5 cms. dia. galvanised iron pipe with

coupling and buch buried in specially prepared earth

pit complete with necessary 8 SWG earth wire.

323 For using salt and charcoal / coke as required for pipe 9.00 Ea. 171.70

type earthing.

324 Supplying & erecting earth pit of minimum bore 7.00 Ea. 4591.46

dia.150mm size approved make Earthing Electrode

consisting Pipe-in-Pipe Technology as per IS 3043-

1987 made of corrosion free hot dipped G.I.Pipes

having Outer pipe dia of 50mm having 80-200 Micron

galvanising, Inner pipe dia of 25 mm having 200-250

Micron galvanising, connection terminal dia of 12mm

with constant ohmic value surrounded by highly

conductive compound with high charge dissipation

suitable for following type of applications with

chamber and heavy duty cover. (A)(approved make

OEM has to submit test certificate including value of

earth resistance of installation duly stamped and

signed by agency and officer Incharge has to ensure

the value of earthing resistane mentioned in test

Certificate) & having back filling compound of (B)

Inner chemical (CCM Compound)- Resistivity:-

ohm / meter testing as per IEC 62561-2017, Voltage

drop:- < 1 volt at no load & dry form, Sulphar content:-

<2%(C) Back fill Compound :- Earthing compound

should be capable to retain moisture for long time

Necessary test report must be submitted by Agency.

(a) For Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

325 Providing & erecting weather proof, dust & vermin 11.70 Sq.Mtr 14902.55

proof, floor mounted front operated indoor type

cubical panel board necessary IP-42 and above

protection as per approval from engineer incharge

made from 14 SWG thick CRC M.S. sheet for outer body

& doors, 16 SWG thick CRC M.S.sheet for internal

partitions with necessary accesories , supporting

angles/ flats channel including cutting, bending,

drilling, welding, riveting with internal partitions &

cable alley as per requirements & instruction of

engineer-in-charge with erection of

supplied switch gears, BUSBARS, suitable size of inter

connecting PVC copper wire / copper-aluminium

strips, rubber grommets, rib, bakelite control

fuses/MCB for measuring instruments, earth bus &

earth bolts, foundation flange - bolts-base Plates,

sufficient nos. of hinged doors, handles with locking

arrangement and rubber gasket,heavy duty end

terminal connection,danger notice board,necessary

ventilation,earthing strip complete. The Panel shall be

painted with epoxy powder coating.

(The rates excludes the cost of switchgears, bus bars,

inter connecting mains & Copper Aluminium strips,

meters, Fuses etc. The dimension shall be measured

excluding base beams) The panel shall be supplied

with following approved manufacturers with

following size.

(B) The standard companies switch gear shall be used

and only manufacturers at CPRI approved factory (i)

326 Providing & erecting weather proof, dust & vermin 2.00 Sq.Mtr 19387.96

proof, floor mounted front operated indoor type

cubical panel board necessary IP-42 and above

protection as per approval from engineer incharge

made from 14 SWG thick CRC M.S. sheet for outer body

& doors, 16 SWG thick CRC M.S.sheet for internal

partitions with necessary accesories , supporting

angles/ flats channel including cutting, bending,

drilling, welding, riveting with internal partitions &

cable alley as per requirements & instruction of

engineer-in-charge with erection of

supplied switch gears, BUSBARS, suitable size of inter

connecting PVC copper wire / copper-aluminium

strips, rubber grommets, rib, bakelite control

fuses/MCB for measuring instruments, earth bus &

earth bolts, foundation flange - bolts-base Plates,

sufficient nos. of hinged doors, handles with locking

arrangement and rubber gasket,heavy duty end

terminal connection,danger notice board,necessary

ventilation,earthing strip complete. The Panel shall be

painted with epoxy powder coating.

(The rates excludes the cost of switchgears, bus bars,

inter connecting mains & Copper Aluminium strips,

meters, Fuses etc. The dimension shall be measured

excluding base beams) The panel shall be supplied

with following approved manufacturers with

following size.

(B) The standard companies switch gear shall be used

and only manufacturers at CPRI approved factory

327 Providing , erecting , fabricating the M.S. structure as 165.00 Kg. 77.77

per requirement on site incorporating proper size of

M.S. angles,square,round, flats, bars, channels, sections

complete with cutting, welding, grinding & finishing

duly painted with one coat of red oxide with erection

on site as per direction of engineer in charge with

necessary grouting, cementing, plastering & finishing

328 Supplying and erecting approved make Octagonal pole 8.00 Ea. 5556.01

made from HR sheet steel. The pole should be made as

per IS. and shall be coated with hot dip galvanizing as

per IS 2629/2633/4759, suitable suspend local wind

speed with integral Junction box consist of terminal

plate of min 6mm Hylam sheet, standard profile

35mmX7.5mm Din-Rail for MCB Mounting, stud type

terminal and arrangement for cable termination to be

erected With Suitable foundation (Included) as per

details given by manufacturer considering site

requirement.

(B) 4 Mtr. Long 70 mm Top X 130 mm bottom dia,

mm thickness with 200mmX200mmX12mm base

plate, 4-M16 Bolts and 450mm long with necessary

G.I. J Bolts .Approx weight 37 kg (Make: Bajaj

,Volmont,Transail )

329 Supplying and erecting approved make Octagonal pole 10.00 Ea. 6874.06

made from HR sheet steel. The pole should be made as

per IS. and shall be coated with hot dip galvanizing as

per IS 2629/2633/4759, suitable suspend local wind

speed with integral Junction box consist of terminal

plate of min 6mm Hylam sheet, standard profile

35mmX7.5mm Din-Rail for MCB Mounting, stud type

terminal and arrangement for cable termination to be

erected With Suitable foundation (Included) as per

details given by manufacturer considering site

requirement.

(C) 5 Mtr. Long 70 mm Top X 130 mm bottom dia,

mm thickness with 200mmX200mmX12mm base

plate, 4-M16 Bolts and 600mm long with necessary

G.I. J Bolts .Approx Pole weight 46 kg (Make: Bajaj

,Volmont,Transail )