Loading
Loading…
Loading…
Eligibility, documents, scope, Go/No-Go checksEligibility, required documents, scope of work and Go/No-Go checks for this tender, in one click.
Tender Value
₹4.0 L
EMD Value
₹8,000
Closing Date
31 Oct 2026, 2:00 pm
Eligibility, documents, scope, Go/No-Go checksEligibility, required documents, scope of work and Go/No-Go checks for this tender, in one click.
EE(ARSM SQ)/WS
15, Raja Subodh Mallick Square, Kolkata 700013.
Replacement of broken rotating assembly with bearings of KBL make 16UPH -2 pump unit no-6 at Auckland Sq BPS.
2026_KMC_1045338_1
KMC/WS/ARSM/38/2026-27
Open Tender
MECHANICAL
Percentage
Auckland Sq BPS
Please refer Tender documents.
4 documents required · 4 mandatory
₹0
₹8,000
9 Oct 2026
9 Oct 2026
2 Nov 2026
9 Oct 2026
31 Oct 2026
9 Oct 2026
This is a percentage-rate BOQ. The schedule below shows estimated quantities and rates. Bidders quote a single percentage above or below the total estimated cost.
| Sl No | Description | Qty | Unit | Est. Rate | Est. Amount |
|---|---|---|---|---|---|
| 1 | DE-COUPLING OF THE HT PUMP FROM THE DRIVE MOTOR BY
REMOVING COUPLING BOLTS ETC WITH CARE & CAUTION AND
KEPT THE COUPLING BOLTS IN THE DEPARTMENTAL GODOWN
& COMPLETE AS PER DIRECTION OF EIC (MODE OF
MEASUREMENT - DRIVE MOTOR WATT * NO OF POLES/ RPM) | 1,250 | 1 UNIT | 0.45 | ₹562.5 |
| 2 | REMOVAL OF HORIZONTAL/ VERTICAL SPLIT TOP VOLUTE
AFTER LOOSENING THE NUTS & BOLTS FROM THE BOTTOM
VOLUTE OF THE HT PUMP WITH UTMOST CARE BY USING
DEPARTMENTAL OVERHEAD CRANE & KEEP THE TOP AT THE
WORKING FLOOR AND AFTER COMPLETION OF THE
NECESSARY INSPECTION/ WORKS ETC & AGAIN PLACING THE
TOP VOLUTE ON THE BOTTOM VOLUTE WITH NECESSARY
HYDRAULIC PAPER ETC ALONG WITH THE SEALING OF BOTH
NDE & DE SIDE OF VOLUTE CASING TO PREVENT SUCKING OF
AIR & BOLTED UP OF THE TOP & BOTTOM VOLUTE CASING &
COMPLETE AS PER DIRECTION OF EIC ( MODE OF
MEASUREMENT - DRIVE MOTOR WATT * NO OF POLES/ RPM) | 1,250 | 1 UNIT | 1.75 | ₹2,187.5 |
| 3 | TAKEN OUT OF THE SHAFT IMPELLER ASSEMBLY FROM THE
BOTTOM VOLUTE OF THE HT PUMP AND KEPT ON THE
PEDESTAL WITH CARE & CAUTION & COMPLETE AS PER
DIRECTION OF EIC (MODE OF MEASUREMENT - WEIGHT OF
IMPELLER, SHAFT, SLEEVE, JAM NUT & HALF COUPLING) | 209.6 | KILOGRAM | 8.5 | ₹1,781.6 |
| 4 | PREPARATION OF ERODED SURFACE AND DO NEEDFUL TO
DEVELOP THE ERODED SURFACE BY METAL MOC-CI FG220)
DEPOSITION /MACHINEABLE ELECTRODE ON THE PITTED
/ERODED PORTION OF THE VOLUTE BODY OF THE
PUMP(SAME MATERIAL TO BE USED FOR METAL DEPOSITION
AS PER THE EXISTING VOLUTE BODY MATERIAL) AND
FINISHED BY GRINDING ETC WORKS & COMPLETE IN ALL
RESPECT AS PER DIRECTION OF EIC (MODE OF
MEASUREMENT AREA IN CM2 OF THE ERODED SURFACE X
MAXIMUM ERODED DEPTH) | 156 | CUBIC CENTIMETER | 85 | ₹13,260 |
| 5 | TO AND FRO TRANSPORTATION OF COMPLETE
SHAFT-IMPELLER ASSEMBLY FROM PUMP HOUSE WORK SITE
TO THE CONTRACTORS WORK SHOP AND VICE VERSA
INCLUDING LOADING AND UNLOADING WITH PROPER CARE
AND CAUTION AS PER DIRECTION OF EIC.(MODE OF
MEASUREMENT- WEIGHT OF IMPELLER,SHAFT, SLEEVE,JAM
NUT AND HALF COUPLING) | 209.6 | KILOGRAM | 9.5 | ₹1,991.2 |
| 6 | REMOVAL OF HALF COUPLING BY HYDRAULIC PULLER AND
FIXTURESETC VERY CAUTIOUSLY FROM THE SHAFT AND
COMPLETE IN ALL RESPECT AS PER DIRECTION OF EIC.(MODE
OF MEASUREMENT- DRIVE MOTOR WATT*NO OF POLES/RPM | 1,250 | 1 UNIT | 0.55 | ₹687.5 |
| 7 | PREPARATION OF SURFACE FOR METAL
DEPOSITION/MACHINEABLE ELECTRODE ON THE
PITTED/ERODED PORTION OF THE IMPELLER BY SUITABLE
METHOD ETC COMPLETE IN ALL RESPECT AS PER DIRECTION
OF EIC MODE OF MEASUREMENT -(DIAMETER OF THE
IMPELLER IN METER)X(DISTANCE BETWEEN THE IMPELLER
EYE IN METER)X(NO OF VANES)X(MAXIMUM DEPTH IN MM OF
THE ERODED PORTION OF THE IMPELLER SURFACE) | 3.8 | CUBIC METER | 975 | ₹3,704.61 |
| 8 | REMOVAL OF IMPELLER USING REQUIRED HYDRAULIC
PULLER & FIXTURES ETC VERY CAUTIOUSLY WITHOUT ANY
DAMAGE EITHER TO THE SHAFT SURFACE ORTO THE KEY ETC
WITH REQUIRED ARRANGEMENT ETC. COMPLETE IN ALL
RESPECT AS PER DIRECTION OF EIC (MODE OF
MEASUREMENT -WEIGHT OF IMPELLER WITH SHAFT) | 142 | KILOGRAM | 38 | ₹5,396 |
| 9 | SURFACE DEVELOPMENT BY METYAL (MOC-SS)
DEPOSITION/MACHINEABLE ELECTRODE ON THE
PITTED/ERODED PORTION OF THE CONVEX SIDE AND
LEADING EDGES OF ALL VANES OF IMPELLER SURFACE(SAME
MATERIAL TO BE USED FOR METAL DEPOSITION AS PER
EXISTING IMPELLER) WITH COMPLETE IN ALL RESPECT AS
PER DIRECTION OF EIC.(MODE OF MEASUREMENT-(DIAMETER
OF THE IMPELLER IN METER)X(DISTANCE BETWEEN THE
IMPELLER EYE IN METER)X(NO OF VANES)X(MAXIMUM DEPTH
IN MM OF THE ERODED PORTION OF THE IMPELLER SURFACE | 2.71 | CUBIC METER | 2,750 | ₹7,463.5 |
| 10 | COMPLETE COATING THE ENTIRE IMPELLER SURFACE WITH
CERAM COAT-54/ EPOXY RESIN AT A THICKNESS OF 400
MICRON DFT BUILT UP IN TWO SUCCESSIVE COATING AND
COMPLETE IN ALL RESPECT AS PER DIRECTION OF EIC.
{MODE OF MEASUREMENT - 2 SIDES X (DIAMETER OF THE
IMPELLER IN METER)X(DISTANCE BETWEEN THE IMPELLER EYE IN METER)X(NO OF VANES)} | 1.09 | SQUARE METER | 3,200 | ₹3,473.92 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.99 MB
BOQ_2562719.xls
BOQ • 0.31 MB
TBID.pdf
Tender Documents • 0.53 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .