8299 SPECIAL REPAIR TO ROOF TREATMENT TO BLDG NO P-134, P-135, P-136 OF 306 FD HOSP AND BATH ROOM BLOCKS T-65, T-66, T-67 AND T-68 AT 883 AT ASC BN AND CERTAIN REV AND MINOR WORKS UNDER GE (EAST) BAREILLY.

Amount

Dismantling Asbestos cement /FRP sheet/GI sheet(corrugated ted, semi corrugated, etc.) sheets in roof coverings up to height 8mtr all as specified and directed by Engr in Charge

M & L for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm TCT thick of any colour approved by GE having tensile strength of 550Mpa as in roof covering / cladding to wall, fixed with 5 Nos. self tapping screws on each sheet /each support rubber lining and filling of gap with cement mortar in CM 1:4 with wall and sheet up to 6 mtr height . complete all as specified and as directed by Engineer-In-Charge.

Dismantling timber unframed scantelings 40sqcm and over of any description not otherwise provided for

S&F steel work in rolled section as approved, purlins, rafter, posts, gusset plates cleats, wind ties etc including special shape washers etc complete using ERW or induction butt welded tubes confirming to IS 116-1979 grade (medium grade)

M & L for Reinforced cement concrete type B1 1:2:4 20 mm graded aggregates as in Beams, cantilevers, bressummers, lintels over 1.5m span. complete all as specified and as directed by Engineer-In-Charge.

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings,girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and as directed.

S&F mild steel TMT bars of 8 mm dia and over cut to length bent to shape required including cranking and binding with mild steel annealed wire not less than 0.9 mm dia or securing with clips. complete all as specified and as directed.

Ditto but 5 mm dia and over up to and including 10 mm dia . complete all as specified and as directed.

M&L for Modular Fly ash brick work , straight or curved on plan exc 6 m mean radius built in cement mortar 1:6. complete all as specified and as directed.

M&L for Modular Fly ash half brick work , straight or curved on plan exc 6 m mean radius built in cement mortar 1:4. complete all as specified and as directed.

M & L for rendering 15mm thick in cement plaster 1:4 on fair surfaces of brick work or concrete surfaces, is to be finished even and smooth without using extra cement in external. complete all as specified and as directed.

M & L for cement concrete type D-2 (1:4:8) usng 40 mm graded broken stone aggregate 75 mm thick as sub base . complete all as specified and as directed.

M & L for coloured Non skid ceramic tiles 7 to 8 mm thick of colour patteren as approved and as per manufacturers catalouge (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 Sqm, in floor etc over 15mm thick screed bed with cement mortar 1:6 and set and jointed in neat cement slurry and pointed in white or coloured cement to match all as specified and directed.

M & L for coloured glazed ceramic tiles 300 mm x450 mm & 7 mm thick on vertical surfaces of colour patteren as approved and as per manufacturers catalouge such as skirting, dados etc, set and jointed in neat cement slurry over and including 10 mm thick bedding layer/ backing coat in CM 1:4 complete and pointed in white or coloured cement to match complete all as specified and as directed.

M & L for cement concrete type C2 (1:3:6) (40 mm graded broken stone aggregate) 75 mm thick as in plinth protection complete all as specified and as directed.

M&L for 2 coats of OBD on new wall surfaces including 2mm thick putty the new surfaces Complete all as specified and as directed.

M&L for Preparing new plastered surfaces on walls and apply two coats of cement base paint. complete all as specified and as directed.

S & F Solid PVC door frame of size 50 mm x 47 mm made out of 10 mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification & drawing compete all as specified as directed.

S & F Factory made solid panel PVC Moulded door shutter 28 to 30mm thick(stiles), with 2,4 or 6 raised panel design 2mm thick Prelam PVC sheet on the front face and 2mm thick Plain colour PVC sheet on back face with particle Board core compete all as specified as directed.

S & F 100 mm Heavy duty Aluminium butt hinges as approved as per sample compete all as specified as directed.

S & F 150 mm Heavy duty Aluminium tower bolt as approved as per sample compete all as specified as directed.

S & F 150 mm Heavy duty Aluminium Handle as approved as per sample compete all as specified as directed.

S & F in Repair Pillar taps , cast copper alloy , with capstan heads, chromium plated, screwed down high pressure fancy type of 15 mm bore size with or without lettered Hot or Coldwith long screwed shanks and flynuts , screwed for iron pipe and fixed Complete all as specified and as directed.

S&F in Repair Cast copper alloy CP angle valve type stop cock with flange suitable for 15mm bore pipe screwed at both ends or high pressure with Capstan head confirming Complete all as specified and as directed by Engineer-In-Charge.

S&F in Repair PVC connection 15mm size with PTMT nuts, of length 600mm Complete all as specified and as directed.

S&F bib tap long body foam flow with flange of bore size 15mm, cast copper alloy, chromium plated, fancy type, with crutch or butter fly handle screwed down, screwed for iron pipe or for brass ferrule Complete all as specified and as directed.

S&F Brass chromium plated tubular towel rail 20mm dia 60cm long with and including flanges complete all as specified and as directed .

S & F soap dish stainless steel as approved by GE complete all as specified and as directed.

S & F in repair Viterous china wash hand basin of size 550 x 400 mm, white colour flat back excluding taps, chain and plug and porcelean stopper but including brackets and CP waste fitting and 32 mm PVC waste pipe . complete all as specified and as directed.

S & F in repair vitreous china wash down water closet pedestal pattern (EWC) white excluding flushing cistern & Incl white seat cover of same make closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device and flush pipe.Complete all as specified and directed.

S&F in repair Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe including fixing plugs , bedding urinal against wall in cement mortar (1:2) etc. including CP Waste fitting and PVC waste pipe.Completed all as specified and directed.

S&F in repair 10 litres capacity PVC Valveless symphonic action type flushing cistern high / low level white complete with inlet , ball valve float and handle including brackets and telescopic down pipes and jointing with WC complete complete all as specified and as directed.

M & L for 75 mm, dia PVC (SWR) floor trap, plain with SS grating including jointing with solvent cement. complete all as specified and as directed.

Supply and fixing Low density polyethylene pipes (LDPE) of pressure rating 6 kg/ cm2 of 40 mm dia bore for wash hand basin Complete all as specified and directed.

Supplying and laying of 20mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. Note : The rate includes for chase cutting of Concealed for all the pipes shall be got tested before providing by Pressure testing machine and got approved and any leakage seepage observed , the conctractor shall be redo the same without any extra payment.

Supplying and laying of 25mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. Note : The rate includes for chase cutting of Concealed for all the pipes shall be got tested before providing by Pressure testing machine and got approved and any leakage seepage observed , the conctractor shall be redo the same without any extra payment.

S& F PVC (SWR) pipes 110mm dia single, socketed in any length ,with rubber ring joints fixed to walls with MS clamps all as directed by Engr in charge.

S&F PVC (SWR) bends 110mm dia complete all as specified.

S&F PVC (SWR) branch piece, double (double Y) equal or unequal complete all as specified.

S& F PVC (SWR) pipes 75mm dia single, socketed in any length ,with rubber ring joints fixed to walls with MS clamps all as.

S&F PVC (SWR) bends 75mm dia complete all as specified.

S&F PVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified.

S&F aluminium powder coated frame for louvers section of size 75x40x1.6mm including 4mm thick glass in louvors of 100 mm width with glazing cleat and revolving arrangement of standard section of aluminium including rubber packing, aluminium beading or gasket for for aluminium sections for fixing glass sheet and necessary fittings complete screws plugs, handle, tower bolt, stay hooks including fixed Aluminium wire cloth etc all as specified and directed.

M&L for Granite (of any colour or any grains as approved) work with 16 to 18mm thick table rubbed and polished as in partitions for urinals complete

Providing & fixing in repair false ceiling at all heights with GRG (Glass Fiber Reinforced Gypsum) false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000 mm, cross - T of size 15x32 mm of length 1200 mm and secondary intermediate cross-T of size 15x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanized iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge. With Fully perforated 10 mm Thick Square edged GRG false ceiling tiles.

S&F rotational moulded polethylene water tank of 1000 ltrs capacity, ISI Marked (cylindrical vertical with closed top with suitable size of M S Tasla with suitable locking system) hoisted and fixed in position all as pacific SSR Part- I including dismantling of existing water tanks capacity n exc 1000 ltr complete all as specified and directed.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar includin gall quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles

M & L two coats of synthetic enamel paint on steel surfaces over one coat of red oxide or zinc chrome primer, of any description over 10cm width or girth including preparation of new or previously untreated surfaces of steel. compete all as specified as directed.

Taking down Chowkats or frames with shutters (without taking off shutters from the frames) n.exc. 1.5sqm each Complete all as specified and as directed.

Taking down Chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.50sqm and n exc 4sqm each Complete all as specified and as directed.

S & F in repair 2nd class hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints,complete all as spd as directed

S&F for 40 mm thick factory made flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed .

S&F 35mm thick factory made glazed and skeleton door shutters open rebated of second class hard wood rail and styles(Hollock), prepared to receive glass/gauge etc without sash bars, edges of framing plain cham-fered or rounded, mitred and rebated sash bars, any numbers The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed . (Note :- S & F Glass/gauge shall be measured and paid for separately)

S & F 300 mm long and Mild steel Chromium plated sliding door bolts, plate type, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed compete all as specified as directed.

S & F mild steel spring 250mm for door, ordinary rat tail rod pattern springs, including roller and roller plate including welding as required for steel frame compete all as specified as directed.

S & F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tracks or wooden beeding patti.compete all as specified as directed.

M & L two coats of synthetic enamel paint over one coat of pink primer on wood or wooden based surface exc. 10cm width or girth including preparation of new or previously untreated surfaces.compete all as specified as directed.

M & L for powder coated aluminium sliding window with anodized aluminium frame of 3 Track of size 92mmx32mmx 1.5mm thick, with sliding shutters(02 glass and 01 Wirecloth) with necessary channels (top rail, bottom rail and style of size 40mmx 18mm x1.10 mm thick) including glazing with tinted sheet glass panel 4.00mm thick and Aluminum alloy wirecloth avg width of aperture 1.4mm fixed outer side with necessary aluminium fillets, fitted with necessary jointing cleats, glazing clips,locking device one for each shutter , rubber packing, aluminium beading, screws, rawl plugs including all necessary holes / drilling etc, complete all as specified as directed by Engineer -in -charge. Note : If mentioned section are not available in market, then immediate next higher section shall be provided by Contractor without any extra cost.

M/L Framed work such as grills as approved , gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 including MS Powder coating to grill/guard bars of approved colors for windows etc completed and all as specified and directed.

Demolition of concrete of any description and in any position not otherwise specifically provided for complete all as spd and directed

M &L for PCC (1:2:4) type B-0 using 10/12.5 mm graded stone aggregrate laid over roof slab after applying cement slurry 3 kg/sqm for filling undulationations finished even and smooth without using extra cement complete all as spd and directed.

M&L screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:4, over RCC roof slabs for laying water proofing treatment mixed with using and including water proofing liquid @ 150 ml per bag of cement complete all as specified and directed. (Note :cost of water proofing liquid shall be deemed to included in quoted rates)

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out hard and dense soil (including existing PCC).

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point

M&L for cement Concrete coloured interlocking paver blocks shall be factory made with casting in rubber/PVC moulds & compacting on a vibro table assembly and shall be cured in curing tank for atleast 14 days and then air dried before use. The paver block shall be confirming to IS 15658 -2006 of 100mm thickness, M-50 Grade. Approved design, shape, size and colour of top layer Incl interlocking tiles laid over 50mm thick sand cushing and pattern and colour as approved by GE complete all as specified and directed.

M&L for PCC (1:2:4) type B1 using 20mm graded agg for coping including weathering, slightly rounded or chemferred angles and throating, as directed.

Taking down copper/aluminum point wiring complete including fixture and fitting such as switches, ceiling roses, pendants, regulators, sockets, light fittings, holders etc and removing the items from site to store for taking credit (credit for above items should be made as per conditions separately ) and making good disturbed surfaces to match with the existing surfaces of walls, floors etc complete all as specified and directed.

M&L for point wiring with FRLS PVC insulated, un-sheathed, multi stranded copper conductor cable of 1.5sqmm size, 1100 volts, drawn through & including concealed 20 mm rigid non metalic PVC conduit with all accessories fixed on wall/ceiling/truss including FRLS PVC insulated, unsheathed, multi stranded copper conductor cable of 1.5sqmm size as earth continuty conductor connected to common earth dolly including required numbers and size of sunk cast pressed steel terminal box made out of MS sheet 1.25 mm thick for mounting of fittings like switches, switch sockets, sockets, regulators etc with 3 mm thick hylum laminated sheet cover including cutting Chases pinning in, for concealed conduit wiring and making goods of disturbed surface not exc 15 cm girth complete all as specified and as directed for:- NOTE: (a) Colour coding shall be followed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green (b) Electrical wiring above false ceiling shall be drawn through medium grade PVC conduit.

One light point / Fan point / Exhaust point / Bell point controlled by one 5A switch

One 5A flush type socket point on same board board

One 5A flush type switch socket point on independent board

All as per Srl item No.70 here in before but One 3 pin socket outlet 15 Amp independent with cable of size 2.5 Sqmm for wiring and earth wire

S&F switch piano flush type single pole one way 5 Amps Complete all as specified & as directed.

S&F Switch Piano flush type single pole one way 15 Amps Complete all as specified & as directed.

S&F Socket outlet 2 in 1, 3 pin 5 Amp flush type.s Complete all as specified & as directed.

S&F socket outlet 2 in 1, 3 pin 5Amp and 15 Amps Complete all as specified & as directed.

S&F Lamp holder ( batten/angle ) PVC/Polycarbonate type with back plate for batten/angle fittings.Complete all as specified & as directed.

S & F in replacement of Ceiling rose, PVC/polycarbonate insulated body type, 3 terminal, 240 volts, 5 Amps complete all as specified and directed.

S & F Lamp LED heat sink white with polycarbonate diffuser, B-22 base cap, retrofit type, 220/230 Volts,7/9 Wattcomplete all as specified and directed.

S & F in repairs LED light fittings 20 Watt ( T-8 ), 4' complete with retrofit tube including connecting up with 3 core flexible copper conductor cable of suitable size Complete all as specified & as directed.

S&F in repairs LED bulk head luminaire hexafit 10 watt LED environmental friendly, ultra modern, energy saving , surface mounted, decorative hexagonal bulk head back lit LED luminaries comprising of high brrightness LED complete all as specified & as directed.

S &F LED building security light fitting 25 Watt LED 230 Volts, AC outdoor type new generation with energy saving and environmental friendly long life made up of high pressure die cast aluminium housing with hight efficiency LED as lighting source and lens embedded and heat resistant polycarbonate cover having bottom opending seperate driver component with IP 66 protetection and impact resistant of IK07 complete all as specified and as directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

S & F Exhaust fan , steel body AC single of size 380 mm sweep havey duty with blades and frame and complete with louvers shutter, voltage 230 Volts. 50 Hz RPM 1200, copper winding including electric connection with three core flexible PVC insulated copper conductor multistranded cable 2.5 sqmm

S&F in repairs sheet metal enclousers (DBS) when MCBs to be used 8 way, 240 Volt, double door single pole & neutral with 200 Amps rated bus bar complete all as specified and as directed.

S&F in repairs MCB single phase and neutral 16A-63A, 230V 10KA. B' curve type complete all as specified and directed.

S&F in repairs MCB SP 6A-32A, 230V. 10KA. B' curve type complete all as specified and directed.

S & F in repairs GI bracket made out from GI pipe 25/32mm dia, 1.20 m long fixed on wall with and including nut, bolts and GI clamps of size 25x4mm as required & including painting etc complete.

S&F Lamp LED rechargeable 10 Watt 230 Volt complete all as specified and directed.

S&F in repairs LED bulk head luminaire 9/10 watt with Engineering plastic housing and oval shaped with holder, clear prismatic diffuser,heat sink integrated including one no. 9/10 Watt LED lamp complete

S&F Ultra slim LED MS Batten light fitting 1X20Watt , powder coated decorative end cap complete with retrofit poly carbonate glass tube LED 20W, 4' long including suitable electric connection with three core flexible PVC insulated copper conductor(multistranded) cable of 1.0sqmm from ceiling rose to batten complete all as specified and directed.

Supply and fixing LED light fitting mirror warm type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

S & F exhaust fan AC single phase, metallic body , heavy duty, 230/240 Volts, of size 300mm sweep with louvers including making suitable size hole in the wall for air flow and grouting of nuts & bolts and washers including making connection with three core copper cable of size not less than 1.5 sqmm from ceiling rose complete all as specified & directed.

S&F in repairs sheet metal enclosres (DBs) when MCBs to be used 08 way 240 Volts double door single pole and neutral with 200 Amps rated bus bar complete all as specified and directed.

S&F in repairs sheet metal enclousers (DBS) when MCBs to be used 4 way, 240 Volts double door single pole & neutral with 200 Amps rated bus bar complete all as specified and as directed.

S&F MCB single phase and neutral 40-63A, 240Volt B- curve complete all as specified and directed.

S&F MCB SP 6A-32A, 240Volt B curve complete all as specified and directed.

S&F in repairs single pole and neutral enclosure with a two pin and earth plug and socket complete with one SP MCB 20 Amps .

S&F in repairs sub main wiring with 2 run FRLS PVC insulated and unsheathed multistranded copper condutor of nominal cross section area 4.0 sqmm alongwith one run of FRLS PVC insulated and unsheathed multistranded copper conductor of nominal cross secrtional area 4.0 sqmm as earth contuinity conductor drawn through in and including PVC condut complete all as specified and as directed.

S&F in repairs sub main wiring with 2 run FRLS PVC insulated and unsheathed multistranded copper condutor of nominal cross section area 6.0 sqmm alongwith one run of FRLS PVC insulated and unsheathed multistranded copper conductor of nominal cross secrtional area 6.0 sqmm as earth contuinity conductor drawn through in and including PVC condut complete all as specified and as directed.

Supply and fix electric water heater storage type (geysers) steel body with copper inner tank and heating element upto 2 KW capacity 25 litre , BEE 5 star rated complete will all accessories such as sefecty valve , thermostat , angle valve , NRV , connection pipe like hold and cold 450 mm long baraided hose with two 15 mm nuts and rubber washer ( 02 Nos for each geyser ) suitble for geyser complete all as specified and as directed .

M&L for earthling complete with Galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm thick buried directrly in ground (earth pit not less than 2.25 mtr deep blow GL) with top edge of earth plate not less than 1.5 Mtr below normal ground level, earth plate surrounded from all sides by 15 cm thick packed layer of vharcoal dust and common salt filled in alternate layers and electrode connections by using Galvanised earth strip 32 x 6 connected by means of bolts, nuts, check nuts and washer of galvanized iron or steel, provision of 40 mm dia GI pipe light grade for protection of GL earth strip and 20 mm dia GI pipe medium grade for watering arrangement and PCC (1:3:6) type B1 chamber, MS funnel, wire mesh, 50 mm thick RCC 1:2:4 type B1 earth pit cover with 6 Nos, 8 mm dia high strength deformed steel TMT bars on both ways including necessary excavation in any type of soil, returning, filling in, removal of surplus soil to distance n exc 50 Mtr, Provision of charcoal and slat complete all as shown in electrical plate No 3 of schedule SSR Part-I. Note : (i) Cost of GI earth strip and GI protection pipe upto 7.5 mtr length shall be deemed to be included in the rate quoted for this item. (ii) The unit rate shall also includes for Wire mesh, funnel, excavation, returning filling, removing, PCC chamber pit ,RCC cover slab with handle for lifting , test point etc.

shiv shakti contractor

M/S SAJJAD HUSSAIN CONTRACTOR

M/S R S Constructions

j u enterprises

VISHAL CONSTRUCTIONS

Shikhar ji Enterprises