ADDN ALTN TO PLINTH PROTECTION AROUND SMQs HARD STANDING WITH RETAINING WALL AND STEPS VARIOUS BUILDINGS GARAGES AT MT COMPLEX AND ASSOCIATED B AND R WORKS AT AF STN SAMANA UNDER UNDER GE (AF) JAMNAGAR NO 1

Amount

M&L for complete removal of existing treatment of any thickness laid over RCC/Roof chajja cleaning and washing of roof with water to remove dust etc as preparation to receive treatment, brooming down or steel wire brushing, scraping down smoke soot, mouls, moss and efflorescent salts and treating oil and greasy spots complete all as specified and as directed.

M&L for brushing neat cement slurry with 3.0kg of cement per sq. metre complete all as specified and directed.

M&L for PCC in roof pading, coving,filling and mass concrete type B-0, 1:2:4 (using 12.5mm graded stone aggregate) complete all as specified and directed

M&L for plastering / screed bed, 10mm thick on concrete surface in CM 1:4, finishing the surface even and smooth without using extra cement, including mixing only liquid water proofing compound as per manufacture instruction complete all as specified and directed Note WPC will be measured & paid separately.

Supply only integral water proofing chemical @ 200ml/Bag of cement complete all as specified and directed.

M&L for water proofing treatment to RCC roof slab all as specified below and as directed:- (a) Apply one coat of glass fibre base bitumen felt primer, grade 2 @ 0.25 Kg/Sqm. (b) Laying APP based ploymeric membrane 3mm thick, minimum wt 3.00 kg/Sqm reinforced with polyester non-wove fabric (weighing not less than 150gms/Sqm ) uniformly embedded during manufacturing process, laid on primed roofs & flashing by forced application having side overlap 100mm and at the end 150mm using Butane torch, and sealing all joints and overlaps (c) Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3, complete all as specified and as directed

Taking down cement plaster of any thickness in cement or cement lime mortar on brick or stone or concrete walls etc. including raking out joints, hacking for key, scrubbing down with water etc, including removal of debries to a distance exc 1.5 km but n.exc 2 Km, complete all as spd and directed Note:- Quoted rate deemed to carryout wk at height upto 5.00 m

M&L for rendering 15 mm thick on stone masonary or concrete surface of walls in cement mortar 1:6 finished complete all as spd and directed

M &L 2 coats of oil bound distemper on new surfaces of walls including preparation to distempering to match with existing work complete all as specified and directed

M & L rendering 10 mm thick in patches on fair faces of brick or concrete surfaces in CM 1:3 as on ceiling, facia roof projection etc finished even and smooth without using extra cement as directed by Engineer-in-Charge.

M &L 2 coats of oil bound distemper on new surfaces of ceiling including preparation to distempering to match with existing work complete all as specified and directed

M&L for rendering 15 mm thick on stone masonary or concrete surface of walls in cement mortar 1:4 finished complete all as spd and directed Note:- Quoted rate deemed to carryout wk at height upto 5.00 m

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) and pattern with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over surfaces walls/fins/facia/soffit/chajja etc complete all as specified and directed Note:- Quoted rate deemed to carryout wk at height upto 5.00 m

M&L for Preparation of old distempered / decorated surfaces of walls and applying Two coat of Distemper oil emulsion complete as specified and directed.

M&L for Preparation of old distempered / decorated surfaces of ceiling and applying Two coat of Distemper oil emulsion complete as specified and directed.

M&L for preparation of old painted wooden surfaces, exc 10 cm width or girth and applying one coat of synthetic enamel paint all complete all as specified & directed.

M&L for preparation of old painted steel surfaces, exc 10 cm width or girth and applying one coat of synthetic enamel paint etc complete all as specified & directed.

Supply & fix Fibre glass mesh of 145 gsm for plastering wk etc complete all as spd all directed

Dismantling wall and ceiling board (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets and assesories etc.

S&F 600x600mmx4mm thick false ceiling of Non esbestos fibre cement building boards (E Board) and including anodised aluminium powder coated (minimum thickness of powder coating 50 micron) snap grid frame work of T section (main & cross member) of size 25 mm x 25 mm x 1.5 mm thick in square pattern of grid size 605mm X 605mm . The aluminium frame work will be supported on side wall with the use of aluminium 'L' section of size 25 mm x 25 mm x 1.5 angles etc. Snap grid shall be supported with hangers of 4 mm dia. Galvanised iron wire adjusting level fixed to roof slabs / truss etc by means of ceiling cleats made out of Galvanised iron flat of size 40 x 3 mm size 60 mm long and expansion hold fasteners 12.5 mm dia 40 mm long, including two coats of synthetic enamel paint over a coat of pink primer complete all as specified directed by the Engineer-in-Charge.

Taking down shutter of any description exc 1.00sqm but n exc 2.00 sqm each complete all as specified and directed by Engineer-in-Charge

S&F 2nd class HW 35mm thick Plain, framed,panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and directed Engineer-in-Charge

S&F 30 mm thick second class hardwood factory made Glazed and skeleton door shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass / gauge, etc., sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a), fitted to chowkats complete.

S & F in repair galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aparture 1.18 mm and fixed with tinned tacks ro galvanised wire stapple complete all as specified and directed by Engineer-in-Charge

M&L for preparing new surfaces of wood or wood based materials of any description not other wise described over 10 CM width or girth new or previously un treated wooden surfaces and applying one coat of pink primer and two coat of synthetic enamel paint complete all as specified & directed.

S&F 100mm butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified & directed.

S&F 150 mm long aluminium anodized barrel tower bolts of extruded section complete all as specified & directed.

S&F 125 mm in size aluminium handles cast type anodized complete all as specified & directed.

S & F 250 mm mild steel sliding bolt plate type stove enamelled black with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts four on bolt plate and two on stapple plate and fixed complete all as specified and directed by Engineer-in-Charge

S & F floor door stopper 140mm size of aluminium alloy body and tounge, anodised, with hard drawn steel spring complete all as specified and directed by Engineer-in-Charge

S&F 200mm, ordinary MS rat tail rod pattern springs including roller and roller plate in repair complete all as specified & directed.

S&F in repair Curtain rod, mild steel, chromium plated with fixing brackets, stops, rollers etc complete all as specified & directed.

Dismantling of floor, hearth or wall tiling or stone slab laid, bedded & pointed in any mortar including demolition of cement mortar bedding or backing coat, including removal of debries to a distance exc 1.5 km but n.exc 2 Km complete all as spd and directed.

M&L Rendering 10mm thick in CM 1:4 on on stone masonry surfaces or surface other than fair face of brick-work or on one side of lathing for skirting/dado etc complete all as spd and directed

M&L for Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 300X 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as spd and directed

M&L for Kota stone slab 18-22mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L for Screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in CM 1:6 complete all as spd and directed

M&L for Non skid, ceramic tiles 7 to 8 mm thick (Square / rectangular) polished area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in floors/ vertical surface etc laid over and pointed with coloured cement to match the tiles complete all as specified and as directed.

M&L for Machine cut kata stone slab flooring 18-22mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

Demolition of RCC of any descrition such as Kitchen chimniy, chajja, shelves, OHT Tanks,Pilar,wall, column.beam etc and in any position not other wise specially provided for complete all as specified and directed by Engineer in Charge (reinforcement cut as required to facilitate demolition)

M & L for RCC Type B1(1:2:4) (using 20mm graded stone aggregate) slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like.including necessary formwork complete all as specified and directed by Engineer-in-Charge

S&F mild steel TMT bar 10mm dia and over cut to length bent to shape required including cranking bending spirally and binding with and including mild steel wise (annealed) not less than 0.9 mm dia complete all as specified and directed by Engineer-in-Charge

Excavation in post holes in hard/dense (or similar holes) each n.exc 0.5 cum, getting out, returning, refilling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm in any type of soil removing surplus soil to a distance n exc 50 m complete all as specified and directed.

M&L for PCC 1:2:4 type C 2 using 40mm graded stone aggregate as in foundation, filling, mass concrete complete all as specified and as directed.

S & F Steel work in tubular/rectangular MS Pipe such as vertical post,trusses, curved truss, rafter, purlins etc. including special shaped washer, nut and bolts etc. complete using ERW or induction butt welded tubes conforming to I.S. 1161-1998 grade St-240 in repair complete all as specified and directed Engineer-in-Charge

S&F plates (Plain or chequered ) channels square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe-410-W(Gde E250) quality A

M&L for Roof trusses (framed), trussed, purlins, crane gantries, rails, vertical col and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections etc) including distance pieces, cleats, washers, nuts and bots of any size etc. Fe 410 -W (Gde-E- 250) quality- A complete all as specified and directed

Dismantling wrought iron or mild steel work of any description not otherwise provided for.

S&F for framed work as in doors or gates of angle, tubular section or other section with gusset plates, rails, braces, etc.( Fe 410 -W (Gde E- 250) quality A , complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges/ pintal hinges, roller or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete

M&L for preparation of new steel surfaces of any description, over 10cm in width or girth,not otherwise, applying two coats of synthetic enamel paint over a coat of red-oxide, complete all as specified.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering/clading to wall, molding/folding in circular/semicircular of any position and height fixed with self tapping screws as specified, As directed by Engr-in-charge

S&F for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

Demolition of cement concrete (unreinforced) in ground floor and pavings not exc 15cm thickness below or above ground level, including removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point

M&L for 100mm thick PCC 1:2:4 type B-2( using 20 mm graded stone aggregate) in loor hardstanding laid in alternate bay system, finish the surface fair and even and fair all as per specified.

M&L for 75 mm thick Cement concrete type C- 2, 1:3:6 (40mm graded aggregate) as plinth protection /hardstanding etc complete all as specified and as directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out hard/ dense soil complete all as specified and as directed.

M&L for hardcore broken stone or boulders of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed by Engr-in-Charge.

M&L for 100 mm thick plain cement concrete 1:4:8 type B2, using 40 mm graded stone aggregate, as in sub base to floors and paving etc all complete all as directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed.

Demolition of ashlar facings, dressed stonework, precast concrete articles and precast concrete block walling etc fixed in cement mortar including all quoins, pillars, arches etc. all as specified and as directed.

M&L for providing precast cement concrete (1:5:8) (using 20mm graded stone aggregate) solid building blocks exe 10 cm thick, in width (with plain or inter locking joints as directed) setting in CM 1:6 complete in wall or pillars or kerbstone all as specified and directed.

Excavation in trenches n.exc 1.50 mtr wide and n.exc 1.50 mtr in depth for foundation etc or shafts, wells cesspits, manholes, pier holes etc n.exc 10 sqm on plan and getting out in Hard/dense soil all as specified and directed

Excavating over areas in soft/loose soil, n exc 1.5 m deep and getting out

Returning filling in including spreading, levelling, watering and well ramming in layer n.exc 25cm in layer all as specified and directed

Removing excavated soil to a distance exceeding 1 Km & n.exc 1.50 km and depositing where directed at a level n.exc 1.50 mtr above the starting point complete

S & F Low density polyethylene pipes (LDPE) 50 mm of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors etc

Demolition of Concrete of any description and in any position not otherwise specifically provided for all as specified and as directed.

M&L for providing cement concrete type D-2, 1:4:8 (using 40mm graded aggregate) as in fdn filling and mass concrete etc complete.

M&L for providing cement concrete type B-1, 1:2:4 (using 20mm graded aggregate) in roof kerbs or mud stops, rounded or chamfered on edges, coping and the like including weathering, sightly rounded or chamfered angles and thoating, as directed. NOTE : -(a) The rates include for use of form work (Straight or curved) (b) Concrete items, if so indicated, shall be reinforced. Reinforcement shall be measured separately

M&L for Forming construction/ dummy/ expansion joints 30mm deep x 10mm wide filled with sealing compound Grade B etc complete all as specified and as directed by Engr-in-Charge.

Dismantling Stone slabs and tiles of any description or thickness in floors,aprons etc laid bedded and pointed in any mortar including removal of debries from the premise complete all as spd and directed.

M&L for Rubber moulded chequered cement concrete tile with white cement and pigment (of approved tint) of size 30 cm x 30 cm x 25 mm thick over and including 15 mm thick screed bed in cement Mortar 1:6, set, jointed and pointed in neat cement slurry complete.

M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade with grey cement and pigment including laying over 20mm thick sand cushning withcomplete all as specified and as directed by Engr-in-Charge.

S&F Rolled mild steel in joist,channel, angles or tees , plates with web and flanges cut to shape drilled and counter sunk for screw, including bending and welding angles as necessary, gusset plates, riveting etc. n.exc 10 kg each brackets conforming to FE-290 Gde-E-165 )complete all as specified and directed by Engineer-in-Charge

Dismantling of plain or corrugated steel sheeting any gauge, thickness, from roof coverings etc complete all as specified and directed.

Taking down carefully any aluminum /copper point wiring (light,fan,socket or power) complete including conduits/casing caping including fixture and fittings such as switches,ceiling rose pendants,regulator sockets etc removing material/debris for taking credit and making good the disturbed surface of walls & floors etc to match with the original existing finish complete all as specified and as directed.

Taking down carefully by unscrewing from fitting and fixtures as switches,ceiling roses, pendents,regulators,bells, sockets, tube light fittings,DB,MCB etc, for reuse at site or carrying to the store( To be found measured only when found serviceable in all rspect for reuse) and refixing all as specified and as directed

M & L for point wiring complete with 1.5 sqmm single core multistranded copper conductor FRLS, PVC insulated and unsheathed cable 650 /1100 volts grade drawn through & including super deluxe casing caping (not less than 25 mm wide) with all its accessories like bends, tees, suitable module PVC boxes o etc fix on wall or ceiling surfaces all as specified including 1.5 sqmm , FRLS type , copper multistranded cable as earth wire and plastic laminated PVC box with cover plate as specified and directed by Engr -in charge:

One light / fan / exhaust fan point controlled by one, one way switch.

One 3 pin socket out let 5 Amps on the independent board.

All as per item No 78 about but with 4.0 sqmm multistranded copper multistranded conductor FRLS cable with 4 sqmm earth wire for one 6 pin socket outlet 15 amps on independent board as specified and directed by Engr -in charge:

S & F switch Piano 5 Amps, flush button type, SP, one way, 230 Volts complete as specified and directed by Engr -in charge.

S & F Switch socket combination multipurpose 5 pin 5 Amps, flush type, 230 / 250 Volts complete as specified and directed by Engr -in charge.

S & F switch socket combination ,6 pin ,15 amps, flush type, multipurpose, 230 / 250 volts complete as specified and directed by Engr -in charge.

M&L for Ceiling rose, 3 terminal polycarbonate body 6 Amps, 250 volts AC, including connecting complete as specified and directed by Engr -in charge.

Supply and fix sheet metal enclosure MCB DB, single pole and neutral, 4 ways double door 240 volts having 200 Amps rated bus bar with balnking plates wherever required and degree of protection I.P 43 -IK 09 with acrylic cover as including all connectionsas directed by engineer in charge

Supply and fix sheet metal enclosure MCB DB, single pole and neutral, 12 ways double door 240 volts having 200 Amps rated bus bar with balnking plates wherever required and degree of protection I.P 43 -IK 09 with acrylic cover as including all connectionsas directed by engineer in charge

Supply and fix sheet metal enclosure MCB DB, triple pole and neutral, 4 ways double door 415 volts having 200 Amps double door rated bus bar with blanking plates wherever required and degree of protection I.P 43 -IK 09 with acrylic cover as including all connectionsas directed by engineer in charge

Supply and fix MCB single pole 240 volts 6 to 32 Amps (to be fixed as per load requirement) 220V with 'C' curve complete as including all connectionsas directed by engineer in charge

Supply and fix MCB Single pole Neutral 240 volts 40- 63 Amps (to be fixed as per load requirement)220V with 'C' curve complete as including all connectionsas directed by engineer in charge

Supply and fix MCB’s triple pole & neutral, 63 Amps, 415 volts with ‘C’ curve, fixed in sheet metal board complete including connecting.

Supply & Fix energy efficient LED tube light fitting with built in LED & integral LED driver 20 watt, channel housing & diffuser of length 1200 mm (approx) with all accessories, fixing arrangement internally pre-wired, fixed in position & connecting complete all as specified and directed by Engg –in-charge.

S&F LED building security light fitting 100 Watt flood, system efficiency not less than 100 lumen / Watt, IP66 protection, consisting of high / low voltage cut off, maintenance free isolated Electronic driver circuits, Low THD, PMMA grade high quality Transmittance lens, Epoxy powder coated Die Cast Aluminium housing with weather proof gasket for lamp & driver compartment, Heat resistance toughened glass fitted in cast aluminium housing with SS screws, pipe, bracket on building,

M & L for sub main wiring with two single core PVC insulated and unsheathed cable 2.50 sqmm with multi stranded copper conductor , FRLS type cable drawn through and includingPVC conduit complete with all accessories alongwith provn of 2.50 sqmm PVC insulated and unsheathed ,multi stranded copper conductor , FRLS type cable as earth wire and connecting to tbe BD with proper size of lugs/thimbles etc comnplete all as specified and directed.

Material and labour replacement for earthing complete with galvanized iron earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below normal ground level) with top edge of the plate not less than 1.5 m deep below normal ground connected to galvanized steel wire 4 mm dia by means of bolts nuts check nuts and washer of galvanized steel, watering pipe of 20 mm bore, galvanised iron, light grade, and 15 mm bore galvanised iron light grade for earth wire protection including all excavation earth work in any type of soil, PCC pit in PCC 1:2:4 type B-1 and RCC 1:2:4, type B1 for precast chamber cover 50 mm thick, reinforced with welded steel wire fabric or XPM Jali (weight not less than 4.00 Kg / sqm), with charcoal, salt, funnel complete all as shown in the electrical plate No 3 of SSR part –I and testing on completion.

Excavation in trenches n.exc 1.5 m wide and n.exc 1.5 m in depth for foundation etc or for shafts, wells, cesspits, manholes, pier holes etc, n exc 10 Sqm on plan area and getting out in soft / loose soil.

Removing excavated soil to a distance n.exc 50 m and depositing where directed at a level n.exc 1.5 m above the starting point all as specified and as directed.

M & L for sand filling in trenches for cable cushioning with clean dry fine sand, including gently punning around cable complete all a specified and directed. NOTE :- Punned thickness of sand will be measured and paid.

Supplying & laying factory made unreinforced precast cable cover LV type 1 flat of size 250 x150 x 40 mm all as directed by Engr-in-Charge.

Supply & laying XLPE insulated, PVC inner sheathed, armoured with galvanised steel strip or wire, heavy duty, LT underground cable, with aluminium conductor 1100 volt grade of size 10 Sqmm 4 core laid in trenches / duct passing through pipe / duct or fixed on pole and connecting and testing etc complete all as specified & directed.

S&F LED building security light fitting 90 Watt, system efficiency not less than 100 lumen / Watt, IP66 protection, consisting of high / low voltage cut off, maintenance free isolated Electronic driver circuits, Low THD, PMMA grade high quality Transmittance lens, Epoxy powder coated Die Cast Aluminium housing with weather proof gasket for lamp & driver compartment, Heat resistance toughened glass fitted in cast aluminium housing with

Supply & fix in repairs round, 2 core cable, PVC insulated and PVC sheathed, Aluminium conductor of size 2.5 Sqmm, for electric connection from feeder / looping box / street light over head line to street light fitting.

Supply and fix steel tubular swaged poles type 410SP-31(9.0 meter long) Swan Neck Type complete with CI base plate and finial an single swan neck, Including foundation and coping

Supply and fix rectengular FRP SMC juncton box IP 55 weather proof water proof 240x130x110 mm with aluminum bus bar 4 Nos with 6 Amp MCB and D clamp and connecting items as directed by Engr in charge

KEVAL ENTERPRISE (BID ID -3161807)

Nitesh Enterprise (BID ID -3165092)

Jagdamba Engineering (BID ID -3172327)