PROVISION OF NARMADA WATER SUPPLY AT AF STATION JAMNAGAR

Amount

NOTE: Schedule ‘A’ Part I to VII are under Ser No. 1.00 to 7.00. are Prepriced by MES. Bidders shall insert their lumpsum amount in the Green coloured field under Col-6 only.

Lump sum price worked out for Building / Structures as listed in Sch `A’ Part I.

Lump sum price worked out for Excavation & Earthwork as listed in Sch `A’ Part II

Lump sum price worked out for Internal Water Supply as listed inSch `A’ Part III

Lump sum price worked out for Internal Electrification as listed in Sch `A’ Part IV.

Lump sum price worked out for Sewage Disposal as listed in Sch `A’ Part V

Lump sum price worked out for External Water Supply as listed in Sch `A’ Part VI

Lump sum price worked out for External Electrification as listed in Sch `A’ Part VII

SCHEDULE `A' PART-VIII MISCELLANEOUS ITEMS OF WORK (Note for items 8 to 30. The contractor shall quote his rate for each of these items separately. The estimated rate is left blank since the same is not prepriced by MES)

Supply and fix exhaust fan 300mm sweep metalic body, 240 V, AC, single phase complete with lovers and shutters including provision of flexible three core copper conductor cable of 23/0.0076 up to ceiling rose and grouting 04 Nos full threaded bolts and nuts etc complete all as specified and as directed.

Supply and fix exhaust fan 450mm sweep metalic body 240 V AC single phase complete with lovers and shutters including provision of flexible three core copper conductor cable of 23/0.0076 up to ceiling rose and grouting 04 Nos full threaded bolts and nuts etc complete all as specified and as directed.

S&F LED street light fitting 45 watt, system efficiency not less than 100 lumen/watt, IP 65 protection, consisting of hight/low voltage cut off, maintenance free isolated Electronic driver circuits, Low THD, PMMA grade high quality Transmittance lens, Epoxy powder coated Die Cast Aluminium housing with weather proof gasket for lamp & driver compartment, Heat resistance toughened glass fitted in cast aluminium housing with SS screws, fixed on suitable size bracket all as specified and directed by Engr-in-Charge.

S&F energy efficient LED tube light fitting integrated batten type with built in LED Chips & integral LED driver 10 watt, channel housing & diffuser of length 600 mm (approx) with all accessories, fixing arrangement internally pre-wired, fixed in position & connecting complete all as specified and directed by Engr-in-Charge.

S&F MCB DB, SPN, 230 V, 8 way, Horizontal double door type, powder coated sheet steel encloure -01 No with following :- (a) MCB, SPN, 25AMP - 01 (b) MCB, SP, 10A - 02Nos (c) MCB, SP, 6A - 02Nos

S&F energy efficient LED tube light fitting integrated batten type with built in LED Chips & integral LED driver 20 watt, channel housing & diffuser of length 1200 mm (approx) with all accessories, fixing arrangement internally pre-wired, fixed in position & connecting complete all as specified and directed by Engr-in-Charge.

Supply and fixing stainless steel bourdon type pressure gauge dial type 0-100Kg/cm2 range with a stainless steel body complete complete including all necessary GI pipe connection fitting / cutting / jointing all as specified and directed by Engr Incharge.

Supply, installation, testing and commissioning of centrifugal pump set suitable for turbid water appliction with liquid temperature between 15˚c to 40˚c with horizontal spindle, bronze impellers with CS shaft and shaft sleeves having capacity of 3125LPM to lift raw water at a head 24meter, nominal speed 1450RPM or per RPM recommended by the manufacturer of pumping set, conforing to IS- 5120 1977, directly coupled with squirrel cage induction motor of suitable capacity or KW as per recommendation of the manufaturer confirming to IS12615(2011) and IS/IEC60034-1 suitable for opration on AC three phase 415V ± 10%, HZ, class F insulation , Duty: S1,S3 80% and above CDF, with premium effcincy standard IE3 IP55, mounted on common base frame made out of suitable size MS Channels. Both Pump and motor mounted on and including common base frame on existing foundation and reconnecting existing suction and delivery pipe line. The assembling of Pump and motor shall be done by the manufacturer of the pump itself and not by any autorised dealer/workshop/rep/sister concern etc. complete all as specifed and as directed by Engr-in- charge.

Notes: (i) Base frame will be fixed on existing paltform with existing arragement available. However rate shall be deemed to be included for the following: - (a) Any Addition/ Alteration of suction 150mm dia DI pipe and delivry side pipe 100mm dia of existing pipes and water connection etc. (b) Installlation of strainer on suction side of suitable dia to match with suction pipe alongwith necessary suitable fixtures/fittings. (c) Arrangement of GI pipe 20mm bore alongwith valve for release of air. (d) Installation of pump set shall be done in the presence of manufacturing engineer and not by any authorised dealer/ workshop/rep/sister concern etc.

Supply, Installation, Testing and Commissioning of factory made CPRI approved LT panel switch indoor type cubical flush mounted suitable for 415 vots 3 phase 4 wire 50 hz system confiriming to IS:5039 of size using CRCA sheet3.15 mm thick with IP-42 degree of protection on angle iron frame size 40x40x5mm, powder coated with 80micron thickness, front and back door opening, compartments with shutters, with provision of cable glands and back door cable entry, with four legs 60 cm long using angle iron 50x50x6mm, spray with two coat of synthetic enameled paint of superior quality over one coat of red oxide primer, air passing holes and locking arrangement at fornt with duplicate keys and making connection of incoming and outgoing cable using proper cable lugs,legs grouted in PCC 1:2:4 and making good disturbed surface complete all as specified and directed and comprising of following :-

M&L boring of holes under road pavement hard standing by trenchless technology using ultra sound technique using necessary machine including insertion of reinforced concrete NP3 pipe of 400 mm dia. Suitable for 36 mpa working pressure etc complete all as specified and directed by Engr-in-Charge. Note :- Quoted rate deemed to be inclusive of NP-3 pipe.

Supply and fix high pressure, heavy duty cast iron non return valve/check valve of sizes 100mm bore,conforming to BS 1868 , Class 600, suitable to hydrostatic test pressure for body 156 kg/sq cm & for seat 115kg/sq cm, both ends flanged in existing line,complete all as specified and directed by Engr-in-charge. Note: Suitable size MS flanges for existing pipe line, Joints and jointing materials shall be included under this item.

Supply, laying, jointing and testing, fixing to wall using clamps/ pole or passing through pipes 1100 volts grade heavy duty electric cable with XLPE insulated, screened , PCV bedded, unarmoured with electric power cable 1100 volts grade with stranded copper conductor of size 4 core 25 sqmm.

Material and labour for construction of valve chamber of size 2000 x 2000 x 1500 mm deep dimensions (Over all internal dimension) for sluice valve etc with PCC foundation, PCC block masonry walls, Plastering, PCC Coping, white washing, mild steel chamber cover, painting to chamber cover including Excavation and earth work in any type of soil complete all as specified below :- Valve chamber shall be provided with the following specification :- (i) Cement concrete for foundation (1:4:8) type D2 using 40mm graded stone aggregate 150 mm thick extended up to 150mm beyond the outer face of block masonry. (ii) Walls of valve chamber 200 mm thick with precast cement concrete (1:5:8) (using 20mm graded stone aggregate) solid building blocks, setting in CM 1:6 complete. (iii) Internal and exposed surfaces of valve chamber both concrete and block masonry surface shall be plastered with CM (1:4), 15 mm thick finished even and smooth. (iv) 50 mm thick coping in PCC 1:3:6 type C1 over block masonry wall. (v) Entire plastered surfaces shall be treated with 3 coat of white wash. (vi) Chamber cover shall be of 6 mm thick MS sheet with 30 x 30 x 5 mm size angle iron frame with hold fast and locking arrangement steel surface shall be painted with two coats of synthetic paint of first quality over one coat of red oxide primer.

Supply & fixing of cast iron Sluice valve PN1.6 as per IS-14846, body, dome, wedge-CI IS:210, rings- bronze IS :318, Spindal-SS I:6603, Gland Packing greasy jute packing, fasteners-CS, Gasket- Natural rubber, nominal size as under, both ends flanged in existing line complete all as specified and directed by Engr-in-Charge. Note : Suitable size flanges for existing pipe line, Joints and jointing materials shall be included under this item.

(a) 400 mm dia

(b) 300 mm dia

(c) 100 mm dia

Supply and fixing cast iron Air release valve with double orifice type (smal & large orifice) of size 80mm dia, Kinetic non clogging & self sealing balls for trouble free oeration, totally tamper proof ideally suited for turbid or clear water conforming to IS:14845/AWWA pressure rating PN 1.6 and jointing materials like gaskets, flanges, nuts and bolts and washer etc complete for fixing arrangement in water pipes mains for following sizes incl taking out old unsv all as directed by Engr-in-Charge.

Supply & fixing Cast iron foot valve 150mm bore confirming to IS :4038 with rubber seating, flanged end complete incl taking out old unsvall as specified and as directed by Engr-in-Charge.

Supply and lay in trenches ductile iron pipes with Spigot ends with external diameter DE 326mm and nominal dia of size DN 300 mm, nominal pipe wall thickness not less than 7.2mm class K-9 rating, ISI marked Centrifugally Cast (Spun) Ductile Iron Pressure pipes conforming to IS:8329/2000 classification, suitable for push-on-joint (Rubber gasket-D jointing) with cement mortor lining inside the pipes and outside zinc coating with Bituminous finish coat as per IS:8329/2000 including EPDM rubber joints conforming IS : 5382 of 1985 all as specified and as directed by Engr-in-Charge

Supply and lay in trenches ductile iron pipes with Spigot ends with external diameter DE 429mm and nominal dia of size DN 400 mm, nominal pipe wall thickness not less than 8.1mm class K-9 rating, ISI marked Centrifugally Cast (Spun) Ductile Iron Pressure pipes conforming to IS:8329/2000 classification, suitable for push-on-joint (Rubber gasket-D jointing) with cement mortor lining inside the pipes and outside zinc coating with Bituminous finish coat as per IS:8329/2000 including EPDM rubber joints conforming IS : 5382 of 1985 all as specified and as directed by Engr-in-Charge

Supply and insertion of ERW steel pipe including specials , supplied and laid complete, nominal dia 300mm and minimum, thickness of 6mm. The type of material is FE-410, epoxy coated internally using solvent free at 150 Sqm/hr with 500 micron Max coating and externally using solvent free at 300 Sqm/hr with 600 micron Max coating confirming to IS: 3589 including fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets, etc. in ground including welding complete all as specified and directed by Engr-in-Charge.

Supply and insertion of ERW steel pipe including specials , supplied and laid complete, nominal dia 150mm and minimum thickness of 5.4mm. The type of material is FE-410, epoxy coated internally using solvent free at 150 Sqm/hr with 500 micron Max coating and externally using solvent free at 300 Sqm/hr with 600 micron Max coating confirming to IS: 3589 including fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets, etc. in ground including welding complete all as specified and directed by Engr-in-Charge.

Supply and insertion of ERW steel pipe including specials , supplied and laid complete, nominal dia 100mm and minimum thickness of 5.4mm. The type of material is FE-410, epoxy coated internally using solvent free at 150 Sqm/hr with 500 micron Max coating and externally using solvent free at 300 Sqm/hr with 600 micron Max coating confirming to IS: 3589 including fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets, etc. in ground including welding complete all as specified and directed by Engr-in-Charge.

Supply, installation, testing and commissioning of online full bore electro magnetic flow meter with 2 line LCD digital display flow converter of meter size DN 350 (ANSI 12") having flow rate range 127.2 to 763.5 m3/hr as per IEC 60068-2-3, EN 60068-2-6 with electromagnetic compatiblity as per 2004/108/EC in conjuction with EN 61326-1(A1, A2), protection class IP 67, suitable for 100-230 Vac, 50Hz or 24V dc, housed in die cast aluminium with polyester finish. The meter should have empty pipe detection facility. The flow meter must display following parameters:(i) Actual flow rate (ii) Total Flow (iii) Flow direction (iv) Flow velocity (v) Mass Flow rate at constant density. Material of construction shall be as under. (a) Measuring tube-SS304 (b)Electrode - SS316 (c) Flanges - Carbon steel (d) Coil Housing- MS (e) Connection box - Die cast aluminium. The contractor shall submit certification for above material of construction and test certificate for meter.

Supply, erecting, testing and commisioning of LLDPE Septic Tank of capacity for 10 Users Horizontal type designed to carry sewage and sullage water complete all as specified and directed. Make- Sintex/Supreme/ AquaTek Note: The quoted rate includes excavation in any type of soil/rock, removal of excavated material as directed, PCC 1:4:8 type D2 for foundation concrete, back filling, Vent shaft, connecting accessories, etc. all as per manufactures instructions for complete functioning of septic tank.

Vijay Construction Co

jagdish machinery stores

JAMNAGAR ELECTRIC AND MACHINERY CO

PATEL CONSTRUCTION CO