A. & A. To E.I. and Street Light Fittings For Dev-Dhoridungari-Virpur-Gandhari Road At Virpur Village, Ta. Virpur, Dist. Mahisagar

Name of Work :- A. & A. To E.I. and Street Light Fittings For Dev-Dhoridungari-Virpur-Gandhari Road At Virpur Village, Ta. Virpur, Dist.

QTY. UNIT RATE IN WORDS TOTAL

providing and erecting Mains with ISI marked, 1.5KV grade electrolyte multi

stranded, annealed copper conductor with heat resistant PVC insulated

conforms to IS 694, IEC - 227 erected in existing pipe of following size Rupees Seventy Paise

(Specifically for control panel, relays, power switchgears, motor starters & Seventy Only

control wiring) with required size of copper lugs, nuts and bolts if required.(e)

One wire 6.00 sq. mm

Replacing old & us by Supplying and erecting Flexible PVC insulated multi

strand multi core 1.1 kv grade ISI marked copper wires of following size to be Rupees Fifty Eight Paise

erected as directed.(e) 1.50 Sq.mm 3 core round PVC sheathed Fifty Eight Only

(Make:Havells,KEI,finolex,RRkable, Apar, polycab)

Replacing old & us by Supplying and erecting LED street light / Flood light

fittings with High power White LEDs wattage of 3 Watt and above assembled on

single MCPCB, efficiency more than 130 lm/w and corrosion free High pressure

die cast aluminum housing with smooth finish powder coated and heat sink

extruded aluminium with diffuser and Polycarbonate optics/ lenses, with

toughened glass with company mark/name engraved or embossed 160 to

V,Power Factor more than 0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity

ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED driver efficiency > 85 %.( Rupees Five Thousand

fittings required LM-79 & LM-80 certificates)(NOTE: Below description have Eighty Paise Thirty Only

shown ranges of Wattage capacity of LED fittings.The Engineer incharge may

select any wattage capacity between the ranges shown.) (A) Street Light (IP-65),

Surge protection -4KV integral and ,Light must have 440VAC line supply with

over-voltage protection. (iii) 60 - 89 watts Cat-lll (Make: Philips , Crompton,

Wipro,Jaguar, Havells) Fittings should be NABL tested and certified.

Replacing old & us by Providing and erecting Approved make Four pole

moulded case circuit breaker having breaking capacity ICU of 25 KA. at

V,having normal current rating up to 25 A to 100A. with Fixed thermal & Rupees Six Thousand

4 magnetic release suitable to work on A.C. supply 50 c/s. with all internal 3.00 Ea. 6790.23 Seven hundred Ninety

connections, spreader tinned copper & complete erected in existing 16 G.M.S. Paise Twenty Three Only

housing.ICS=100% of ICU only Cat III

(Make:L&T,havells,Hager,C&S, Siemens)

Providing and erecting Approved make Earth fault Relay suitable to mount with

inter connection suitable to following size of moulded case circuit breaker Rupees Five Thousand

5 having CT ratio & MCCB rating as following along with shunt trip 220V AC. with 3.00 Ea 5156.05 One hundred Fifty Six

all internal connections & complete erected in existing M.S.housing.. (1) 15 A - Paise Five Only

100 A , CT Ratio 1/100

Replacing old & us by providing and erecting Miniature circuit breaker single

Rupees Two hundred

pole 0.5A to 2A system and having breaking capacity 10 KA to be erected in

6 132.00 Ea 297.95 Ninety Seven Paise Ninety

existing box. confirming to IS 8828/1996 with ISI Mark Cat III

(Make:L&T,havells,Hager,C&S, Siemens)

Providing and erecting Pipe type earthing having 150 cms.long and 2.5 cms. Rupees Three hundred

7 dia. galvanised iron pipe with coupling and buch buried in specially prepared 6.00 Ea. 368.65 Sixty Eight Paise Sixty

earth pit complete with necessary 8 SWG earth wire. Five Only

For using salt and charcoal / coke as required for pipe type earthing. Rupees One hundred

8 6.00 Ea. 171.70 Seventy One Paise

Supplying & erecting earth pit of minimum bore dia.150mm size approved make

Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987

made of corrosion free hot dipped G.I.Pipes having Outer pipe dia of 50mm

having 80-200 Micron galvanising, Inner pipe dia of 25 mm having 200-250

Micron galvanising, connection terminal dia of 12mm with constant ohmic value

surrounded by highly conductive compound with high charge dissipation suitable

for following type of applications with chamber and heavy duty cover.

(A)(approved make OEM has to submit test certificate including value of earth

resistance of installation duly stamped and signed by agency and officer Rupees Four Thousand

9 Incharge has to ensure the value of earthing resistane mentioned in test 3.00 Ea 4591.46 Five hundred Ninety One

Certificate) & having back filling compound of (B) Inner chemical (CCM Paise Forty Six Only

Compound)- Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017,

Voltage drop:- < 1 volt at no load & dry form, Sulphar content:- <2%(C) Back fill

Compound :- Earthing compound should be capable to retain moisture for long

time Necessary test report must be submitted by Agency. (a) For Electrical

Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

QTY. UNIT RATE IN WORDS TOTAL

Providing , erecting , fabricating the M.S. structure as per requirement on site

incorporating proper size of M.S. angles,square,round, flats, bars, channels,

Rupees Seventy Seven

sections complete with cutting, welding, grinding & finishing duly painted with

10 134.00 Kg. 77.77 Paise Seventy Seven

one coat of red oxide with erection on site as per direction of engineer in charge

with necessary grouting, cementing, plastering & finishing complete.

Replacing old & us by Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured

cable multistrand / Solid Aluminium conductor for 1.1 KV. to be laid on wall with Rupees One hundred Sixty

11 necessary clamps or in existing trench / pipe of following size of cables (C) 4 643.00 Mtr. 168.67 Eight Paise Sixty Seven

core 10 Sq. mm (Make:Havells,KEI,finolex,RRkable, Apar, polycab) Only

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand

Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in Rupees One hundred

12 existing trench / pipe of following size of cables (A) 4 core 16 Sq. mm 38.00 Mtr. 184.83 Eighty Four Paise Eighty

(Make:Havells,KEI,finolex,RRkable, Apar, polycab) Three Only

Making trench in Hard Murrum / Tar Road of suitable width of 90 cm or required

Rupees Seventy Four

13a depth for laying any size of cable or locating the fault all over the run and back 394.00 Mtr. 74.74

Paise Seventy Four Only

filling the same and making the surface as normal ground.

(B) If additional machinery like hammer driller or JCB use [Add] Rupees Four hundred

13b 205.00 Mtr. 432.28 Thirty Two Paise Twenty

Providing & laying approved make Double walled corrugated pipes (DWC) of

polyethylene(conforming to IS 14930 II )with necessary connecting accessories

Rupees Sixty Two Paise

14 of same material at required depth in existing trench for laying of cable. below 642.00 Mtr. 62.62

ground / road surface for enclosing cable (A)50 mm outer dia

Providing and, fixing heavy duty flange type brass cable gland with rubber ring

Rupees Thirty Eight Paise

15a for PVC insulated armoured cable complete with out going tails, insulating tape 28.00 Ea 38.38

Thirty Eight Only

etc for following size of cables.(C) 2 to 4 core 10 Sq. mm

(D) 2 to 4 core 16 Sq. mm Rupees Forty Seven

Paise Forty Seven Only

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of

following size evenly crimped with high pressure tool & connected to switchgear Rupees Thirteen Paise

terminals with brass/cadmium plated nut bolts in an approved manner. (B) 10 Thirteen Only

(C) 16/25 Sq.mm. Rupees Fifteen Paise

Replacing Old & broken Octagonal Pole by Supplying and erecting approved

make Octagonal pole made from HR sheet steel. The pole should be made as

per IS. and shall be coated with hot dip galvanizing as per IS 2629/2633/4759,

suitable suspend local wind speed with integral Junction box consist of terminal

plate of min 6mm Hylam sheet, standard profile 35mmX7.5mm Din-Rail for MCB

Rupees Twelve Thousand

Mounting, stud type terminal and arrangement for cable termination to be

17 6.00 Ea 12553.29 Five hundred Fifty Three

erected With Suitable foundation (Included) as per details given by

Paise Twenty Nine Only

manufacturer considering site requirement.(E) 7 Mtr. Long 70 mm Top X

mm bottom dia, 3 mm thickness with 225mmX225mmX16mm base plate, 4-

M20 Bolts and 600mm long with necessary G.I. J Bolts .Approx Pole weight

kg (Make:Transrail,Bajaj,Utkarsh,Ambica)

Removing and Reinstalling Existing 7 Mtr Octagonal Pole

Rupees Five hundred Sixty

Paise Fifty Five Only

Providing 1:2:4 cement concrete foundation & 70 % PCC from bottom including

excavation for the pole of size 60 x 60 x 120 cm. Deep in below ground level Rupees One Thousand

19 with plinth of 45 cm x 45 cm(or 45 cm dia x 45 cm) high upper ground level with 12.00 Ea 1292.80 Two hundred Ninety Two

necessary curing and finishing in approved manner. ( for 7.5 & 8/8.5 mtr pole) Paise Eighty Only

Supplying and erecting Street light pole bracket comprising main B Class GI

pipe of 4.2 cm/require outside dia. complete with suitable B Class G.I. sleeve

tubing of approx. 45cms.length and suitable for 76.5mm/80mm/require size of

pole top having nuts and bolts for fixing the brackets and having spread of 0.5 Rupees Six hundred

20a mtr. Length with 110 deg.with vertical plane and suitable welded stiffener 3.00 Ea 622.16 Twenty Two Paise Sixteen

reducer and nipple with check nut complete painted with one coat.of Red oxide / Only

PU base primer and two coats of Aluminium / PU paint. paint with following nos

of arms.[B] Double Arm Bracket 0.5 Mtr

[C] Three Arm Bracket 0.5 Mtr Rupees Seven hundred

20b 3.00 Ea 743.36 Forty Three Paise Thirty

QTY. UNIT RATE IN WORDS TOTAL

Replacing old & us by Supplying & erecting IP 55 grade following size section

pillar fabricated from joint less M.S. Sheet with angle iron legs made from

jointless M.S. Angle with cable clamps to be buried in ground to have

appropriate erection to work uniform until erected with cement concrete

foundation and 45 cm high bricks work finishing with plaster etc. hinged double

door internally supported on both side, with internal and outside looking

Rupees Three Thousand

arrangement with look and keys in duplicate 35 x 35 x 5 mm M.S. Angle of Two

21 3.00 Ea 3595.60 Five hundred Ninety Five

Nos. one is welded and other with nut and bolt for erecting Bakelite sheet.

Paise Sixty Only

Painting the Section Pillar inside and out side with three tank powder coated

paint. section pillar roof should be without joint with water leakage proof &

tested as per IP 55 test & followed by IS 2147 of 1962 (B) 75 X 60 X 45 cm

section pillar fabricated from 16 Gauge MS Sheet with angle iron legs 45 cm

long made from 35 X 35 X 5 mm thick MS angle.

Supplying and erecting HYLAM sheet on existing angle iron frame.for following Rupees Seven hundred

22 thickness (B) 4mm 2.00 Sq. Mtr. 771.64 Seventy One Paise Sixty

Replacing old & us by Supplying & erecting approved make Digital time switch

having lithium cell 6 years operative and operate battery backup 1 channel day

clock with 14 memory programme, suitable to operate on 240V + 5%, 16A with,

Rupees Three Thousand

floating contacts Minimum switching setup time 1 minimum & LCD display. Also

23 3.00 Ea. 3168.37 One hundred Sixty Eight

comprised permanent ON/OFF switching. Programming switches & housed in

Paise Thirty Seven Only

fire proof thermoplastic enclosure & transparent cover erected as required with

necessary connection erected as directed.

Replacing old & us by Supplying & erecting power contactor ,AC3 duty for time

Rupees Two Thousand

switch complete erected as per direction Cat III (D) 4 pole 440V 40 Amp.

24 3.00 Ea. 2782.55 Seven hundred Eighty Two

Paise Fifty Five Only

Supplying and erecting approved make suitable panel indicator LED type lamp, Rupees Forty Three Paise

lens cover, complete erected with necessary connections. Forty Three Only

AMOUNT PUT TO TENDER FOR RS.

Special condition

As there is replacement warranty has to provide for LED fitting for 3 years, so security Deposit an amount Rs. 68,076/- will be released only after

completion of warranty period or the replacement of defective LED fitting whichever is later. Further after issuing the notice to the contractor for replacement of

defective material, he has to take up the work of replacement within 10 days from the date of issuing the said notice, in case where the delay for replacement, the

contractor shall be penalized by Rs. 100/- per day for such delay. In case of non replacement of the defective material action will be taken against the contractor

to keep his registration in abeyance for three years and his full security deposit will forfeited to the Government.

Signature of Contractor Executive Engineer

R&B Electrical Division