CONSTRUCTION OF I.T.I. SRINAGAR DISTT. PAURI GARHWAL

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. :All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil, Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

P/L cement concrete - all works upto plinth level : 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size)

P/L cement concrete - all works upto plinth level : 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. All works upto plinth level

P/L RCC M25 design mix for columns, pillars piers etc.

P/L RCC M25 design mix in lintel beams and girders etc.

P/L RCC M25 design mix for suspended floor, balconies etc.

P/L RCC M25 design mix for Staircase etc.

P/L RCC M25 design mix for Chajjas

Centering and shuttering including strutting, propping etc. and removal of form for :

Foundations, footings, bases of columns, etc. for mass concrete

Columns, Pillars, Piers, Abutments, Posts and Struts

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Suspended floors, roofs, landings, balconies and access platform, with water proof ply 12 mm thick

Stairs, (excluding landings) except spiral-staircases

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)

Providing and fixing Tata pravesh vison panel glass door and frame with hardware ( hinges, lever handle with lock, tower bolt) and instalation

Providing and fixing Tata pravesh normal door and frame with hardware ( hinges, lever handle with lock, tower bolt) and instalation

Providing and fixing Tata pravesh vison panel glass fire door and frame with hardware ( hinges, lever handle with lock, tower bolt) and instalation

Providing and fixing Tata pravesh shaft door and frame with hardware ( hinges, lever handle with lock, tower bolt) and instalation

Providing and fixing Tata pravesh window and ventilators and frame with hardware ( hinges, lever handle with lock, tower bolt) and instalation (Glass, Grill and wire gauge)

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required : In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing 1 mm thick M.S. sheet sliding-shutters, with frame and diagonal braces of 40x40x6 mm angle iron, 3 mm M.S. gusset plates at the junctions and corners, 25 mm dia pulley, 40x40x6 mm angle and T- iron guide at the top and bottom respectively, including applying a priming coat of approved steel primer

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete with double charge

Providing and laying Vitrified tiles in different sizes (thickness to be specifiedby manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete with double charge

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent

62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 fine sand)

6 mm cement plaster 1:3 (1 cement: 3 fine sand)

Finishing walls with APEX SUPREMA paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm. Product-APEX SUPREMA asianpaint, TRUCARE EXTERIOR WALL PRIMER SUPREMA asianpaints. code- 1030 ( apex), 1019 (exterior primer)

Distempering with TRACTOR SUPREMA EMULSION of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water tinnable priming coat with cement primer. Product- TRACTOR SUPREMA EMULSION asianpaints, TRUCARE SUPREMA INTERIOR PRIMER - WT asianpaints. code- 5699 (EMULSION), 0086 (PRIMER).

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Providing and applying white cement based TRUCARE WALL PUTTY SUPREMA of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Product- TRUCARE WALL PUTTY SUPREMA Asianpaints. code- 5440

Natural stone of thickness 18 mm for wall lining (cladding work), backing filled with a grout of average 12 mm thick in cement mortar 1:3 (1 cement : 3 coarse sand), including pointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with an admixture of pigment to match the stone shade complete with all respect.

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design :

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame o f 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mmnominal size), inside plastering 12 mm thick with cement mortar 1:3 (1cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth for manholes : With Sewer bricks conforming to IS : 4885

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.

Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand).

P/L cement concrete - all works upto plinth level : 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size)

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate: 40 mm thick with 20 mm nominal size stone aggregate

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface.

(iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).

supply& installationof IKO Cambridge Roof shingles sheet with stormtite synthetic underlayment over RCC slopi roof plastered surface.

supply& installationof IKO Cambridge Hip & ridge Plus.

40 mm thick marble chips flooring, rubbed and polished to granolithic finish, under layer 31 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size) and top layer 9 mm thick with white, black, chocolate, grey, yellow or green marble chips of sizes from 4 mm to 7 mm nominal size, laid in cement marble powder mix 3:1 (3 cement : 1 marble powder) by weight in proportion of 4:7 (4 cement marble powder : 7 marble chips) by volume, including cement slurry etc. complete: Light shade pigment with white cement

Marble chips skirting up to 30 cm height, rubbed and polished to granolithic finish, top layer 6 mm thick with white, black, chocolate, grey, yellow or green marble chips of sizes from smallest to 4 mm nominal size, laid in cement marble powder mix 3:1 (3 cement : 1 marble powder) by weight in proportion of 4:7 (4 cement marble powder mix : 7 marble chips) by volume : 18 mm thick with under layer 12 mm thick in cement plaster 1:3 (1 cement : 3 coarse sand) :Light shade pigment with white cement

e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineerin-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

Water supply Providing and fixing Jaquar water closet orissa pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan with integral type foot rests Description- ORISSA PAN, code-ECSWHT-451, size- 450x585x255 MM

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing Parryware white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement Production Description- Indus wall hung set, code- c02651c+ e80941c+ c07691c and size 600x380x740 mm

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 1500x450 mm

P/L 110 mm dia UPVC soil waste pipe with pressure 6kg/CM2 for sewer.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms

P/F Upvc nahani trap 110x110mm dia

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.

P/F Upvc terminal guard 110 mm dia

Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 15 mm nominal bore with 45 cm length

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 110 mm bend

P/F Upvc door bend 110 mm dia.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 32 mm dia

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming toIS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

P/F white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing parryware white vitreous china flat back half stall urinal with fittings, half stall urinals. Production Description- Niagara N Urinal, code- C05791C+E81131c, size - 250x330x460 mm

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. Granite Stone of approved shade

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 510x1040 mm bowl depth 250 mm

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

110 mm bend

110 mm Shoe

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete (1:2:4).

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.: Concealed work, including cutting chases and making good the walls etc. : 15 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge Internal work - Exposed on wall

20 mm dia nominal bore

25 mm dia nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. : External work: 40 mm nominal outer dia Pipes

Providing and fixing parryware C.P. brass bib cock auto closing of approved quality conforming to IS:8931 : 15 mm nominal bore. Production Description- Bib cock Auto Closing, code- G2056a1

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

20mm nominal bore

25 mm nominal bore

40 mm nominal bore

Providing and fixing PTMT grating of approved quality and colour. 100 mm nominal dia

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 20 mm nominal bore

Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main : 25 mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore

Providing and fixing parryware C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore 15mm nominal bore. Production Description - Angel Valve Trigon, code- T9828A1

Providing and fixing parryware C.P. brass urinal valve for urinal points of approved quality conforming to IS:8931 a) 15 mm nominal bore 15mm nominal bore. Production Description - urinal valve auto closing, code- T9828A1, code - G2007A1

Providing and fixing parryware C.P. brass bib cock approved quality conforming to IS:8931 a) 15 mm nominal bore 15mm nominal bore. Production Description - urinal valve auto closing, code- Claret Bib Cock, code - T4604a1

Providing and fixing parryware C.P. brass health faucet for european w.c. points of approved quality conforming to IS:8931 a) 15 mm nominal bore 15mm nominal bore. Production Description - urinal valve auto closing, code- Splash Health faucet, code - T9805a1

(0.6x0.6 m section)DRAIN Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Shuttering for Suspended floors,roofs,landings,

P/L 40 mm thick Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement

20 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)

INTERNAL ROAD Excavation in Soil with Dozer with lead upto 100 m Excavation for roadway in soil by mechanical means including cutting and pushing the earth to site of mbankment upto a distance of 100 m, including trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.

Granular Sub-base with Well Graded Material By Mix in Place Method Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401.

For Grading I Material

Providing and Laying of Interlocking Concrete Block Pavements of M-40 Grade having thickness 80 mm as per drawings and Technical Specification Clause 1504.

Cast in Situ Cement Concrete M 20 Kerb with Channel (Construction of cement concrete kerb with channel with top and bottom width 115 and 165 mm respectively, 250 mm high in M 20 grade PCC on M10 grade foundation 150 mm thick, kerb channel 300 mm wide, 50 mm thick in PCC M20 grade, sloped towards the kerb, kerb stone with channel laid with kerb laying machine, foundation concrete laid manually, all complete as per clause 408) Using Concrete Mixer

Painting Two Coats on New Concrete Surfaces Painting two coats including primer coat after filling the surface with synthetic enamel paint in all shades on new, plastered / concrete surfaces as per drawing and Technical Specification Clause 1701

LANDSCAPPING Trenching in ordinary soil up to a depth of 60cm including removal and stacking of serviceable materials and then disposing of by spreading and neatly levelling with in a lead of 50m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or/and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).

Supplying and stacking of good earth at site i/c royalty and carriage up to 1 km (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking sludge at site including royalty and carriage up to 1 km (sludge measured in stacks will be reduced by 8% for payment)

Supplying and stacking at site dump manure from approved source, including carriage up to 1 km (manure measured in stacks will be reduced by 8% for payment) : Screened through sieve of I.S. designation 20 mm

Rough dressing the trenched ground including breaking clods

uprooting weeds from the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation

Fine dressing the ground

Spreading of sludge, dump manure or/and good earth in required thickness (Cost of sludge, dump manure or/ and good earth to be paid separately)

Mixing earth and sludge or manure in proportion specified or directed by the officer-in-charge

Uprooting rank vegetation and weeds by digging the area to a depth of 60cm, removing all weeds and other growth with roots by forking repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of all rubbish with all leads and lifts

Preparation of beds for hedging and shrubbery by excavating 60cm deep and trenching the excavated base to a further depth of 30cm refilling the excvated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of rearth after redution by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling and directed, within a lead of 50m. lift upto 1.5m complete (cost of sludge, manure or extra earth to be paid for seperately)

Digging holes in ordinary soil and refilling the same with the exavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reductin by 8%9 flooding with water, dressing including remocal of rubbish and surplus earth, if any with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for seperately) Holes 45cm dia and 45cm deep

Providing and fixing M.S. flat iron tree guard 60 cm dia and 2 m high, above ground consisting 4 nos 25 x 6 mm, 2.25 m long and 8 nos 25 x 3 mm 2 m long verticals M.S. flats, riveted to 3 nos 25 x 6 mm M.S. flat iron rings in two halves, fixing together at site with required six numbers of 8 mm dia and 30 mm long bolts, including painting two coats with synthetic enamel paint of approved brand and manufacture over a coat of primer. One name plate of 1 mm thick M.S. sheet of size 250x100 mm shall be welded to the tree guard near the middle height and lettered CPWD / PWD/ any other approved name. The tree guard shall be suitably fixed to the ground by embedding four legs of tree guard in pits of suitable dia and to a depth of 25 cm, refilling the pits with soil and ramming, complete in all respect as per satisfaction and direction of Officer-in-charge.

Edging with bricks laid dry length wise, including required excavation, refilling, consolidating with hand packing and spreading surplus earth neatly within a lead of 50 m : Common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Preparation of mounds of various size and shape by available excavated / supplied earth in layers not exceeding 20 cm in depth, breaking clods, watering of each layer, dressing etc., lead upto 50 meter and lift upto 1.5 m complete as per direction of Officer-in-charge

UNDERGROUND WATER TANK P/L 52 mm thick C.C. flooring with concrete hardener topping, under layer 40 mm thick C.C. 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

12mm C.P. finished with a floating coat of neat cement in cement mortar 1:4( 1 cement : 4 fine sand)

P/F in position pre cast RCC manhole cover and frame of required shape and of approved quality. Rectangular shape 600x450mm internal dimensions

Providing MS foot rest including fixing in manholes with 20x20x10cm cement concrete blocks 1:3:6 as per standard design. (i) with 20x20mm square bar

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), including grouting the joints with white cement and matching pigments etc., complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make,in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

(ii) 2nd layer of 25 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) mixed with water proofing compound in recommended proportions. (iii) Finishing top with stone aggregate of 10 mm to 12 mm nominal size spreading @ 8 cudm/sqm thoroughly embedded in the 2nd layer. Using rough kota stone.

Providing and laying integral cement based treatment for water proofing on the vertical surface by fixing specified stone slab 22 mm to 25 mm thick with cement slurry mixed with water proofing compound conforming to IS:2645 in recommended proportions with a gap of 20 mm (minimum) between stone slabs and the receiving surfaces and filling the gaps with neat cement slurry mixed with water proofing compound and finishing the exterior of stone slab with cement mortar 1:3 (1 cement : 3 coarse sand) 20 mm thick with neat cement punning mixed with water proofing compound in recommended proportion complete at all levels and as directed by Engineer-in-charge : Using rough kota stone.

BOUNDARY WALL AND GATE P/F ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters

A) 35 mm thick including ISI marked Stainless Steel butt hinges

P/F Pressed steel door frames manufactured from commercial mild steel sheet of 1.25 mm thickness including hinges jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25mm, Profile C

Providing and fixing MS standard rolled steel glazed windows of required sizes side hung, top hung or fixed in position with CC block of size 15x10x10cm with all fittings.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding

Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete. With 12 mm mild steel U beading

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 5.5 mm thick glass panes

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade : New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

P/F concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron ‘Y’ shaped placed 2.4 m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre

RAIN WATER TANK Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. :All kinds of soil.

P/L C.C. of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 cement : 4coarse sand : 8 graded stone aggregate 40 mm nominal size)

Brick work with bricks of Ist class in foundation and plinth in cement mortar 1 : 6

P/F in position pre cast RCC manhole cover and frame of required shape and of approved quality. EHD - 35 : Circular shape 560 mm internal dia

Providing MS foot rest including fixing in manholes with 20x20x10cm cement concrete blocks 1:3:6 as per standard design. (i) with 20x20mm square bar

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre depth below ground level. All types of soil 300 mm dia

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineerin- charge.

Supplying, assembling, lowering and fixing in vertical position in bore well,unplasticized PVC medium well casing (CM) pipe of required dia,conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 150 mm nominal size dia

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 150 mm nominal size dia

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 150 mm dia.

Providing and fixing M.S. clamp of required dia to the top of casing/housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts f required size complete. 150 mm clamp

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I): 150 mm dia.

Water supply Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.

50 mm dia

65 mm dia

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end):

50 mm dia

65 mm dia

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation oncrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality :

50 mm diameter pipe

65 mm diameter pipe

Providing and filling sand of grading zone V or coarser grade, allround the G.I. pipes in external work :

50 mm diameter pipe

65 mm diameter pipe

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :

50 mm diameter pipe

65 mm diameter pipe

Sewer, STP Excavating trenches of required width for pipes, cables, etc, including excavation for sockets, depth upto 1.5 m, including getting out the excavated materials, returning the soil as required in layers not exceeding 20 cm in depth, including consolidating each deposited layers by ramming, watering etc., stacking serviceable material rmeasurements and disposal of nserviceable material as directed, within a lead of 50 m :Ordinary rock : Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design :

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame o f 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry M.H. in C.M. 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with C.M. 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in C.C. 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90X80X45 cm i/c C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth for manholes : With Sewer bricks conforming to IS : 4885

P/L non-pressure NP2 class (light duty) R.C.C. pipes with collars. 300 mm dia

Supplying, installation, testing and commissioning of STP of appropriate technology including Civil Works, Tertiary Treatment etc. for the Building/ campus. : Per Day for Plant size upto 50,000 LPD

FIRE HYDRANT/ WET RISER SYSTEM: Providing,fixing,testing and commissioning,Single Headed Stainless Steel,ISI marked oblique pattern hydrant/ landing valve with 80 NB flanged inlet & 63 mm dia instantaneous type female outlet complete with cap and chain,twist release type lug and all accessories as per IS 5290-1983 (Type-‘A’).

Make :– New Age /Omex/ ISI / Getech / Safe Fire

Providing, Fixing, Testing and Commissioning of First Aid Fire Hose Reel wall mounting swinging type complete with drum, bracket, 30 Mtr. Long high pressure hose reel tubing as per IS:44 with gun- metal shut off nozzle with 5 m orifice.The hose reel shall strictly confirm to IS:884-1985.

Make :– New Age / Omex / ISI / Getech / Safe Fire

Providing and fixing Stainless Steel Fire Brigade Inlet breaching head as per IS:904 Specification tested for 20 Kg/cm2 with 63 mm dia instantaneous type inlet and 150/100mm dia flanged outlet with built-in check valve for fire brigade connection to under ground tanks and fire risers including companion flanges as per table "E" including nuts,bolts & washers etc.

Make :– New Age /Omex/ ISI / Getech / Safe Fire

Two way

Four Way

Providing and fixing of Stainless Steel 63 mm dia.Short Branch Pipe with 16 mm dia,nozzle (IS:903).

Make :– New Age /Omex/ ISI / Getech / Safe Fire

Providing, Fixing, testing & commissioning of Air Cushion Tank (Air Vessel) 200 mm dia & 1000 mm high with dished top, made of minimum 6 mm thick MS pipe/plate complete with 20 mm dia, brass air valve (ball type), 20 mm stop valve pressure gauge and all accessories as required including fixing brackets.

Providing, Fixing, testing & commissioning of Air Cushion Tank (Air Vessel) 450 mm dia & 1500 mm high with dished top, made of minimum 6 mm thick MS pipe/plate complete with 20 mm dia, brass air valve (ball type), 20 mm stop valve pressure gauge and all accessories as required including fixing brackets.

Providing, laying, testing and commissioning of "C" class MS Pipe conformingto IS: 1239 / IS:3589 including MS fittings like elbows, tees, flanges, tapers,nuts,bolts,gaskets etc with a coat of primer and paint

Make :– Jindal / Surya/ Prakash / Tata

200 mm dia

150 mm dia

100 mm dia

80 mm dia

Excavation and providing wrapping coating to underground ms pipe lines anticorrosive treatment withcoaltar/asphaltic tape as per IS :10221, refilling the trench etc. complete of all sizes as required .

Providing, Fixing, testing & commissioning of cast iron flinged ISI marked -Non-Return Valves complete with rubber insertions, nuts, bolts and washers etc. IS:5312 of following sizes:

Make :– Zoloto / Kirloskar / Sant / Kartar / ISI

150 mm dia

100 mm dia

Providing, fixing, testing & commissioning of cast iron flanged IS marked Butterfly Valve class PN-1.6 complete with rubber etc.IS:780 of following sizes:

Make :– Zoloto / Kirloskar / Kartar / ISI

150 mm dia

100 mm dia

Providing and fixing of Stainless Steel Fire brigade Suction Hose Coupling (draw out connection) with nut for female coupling as per IS 902-1974 complete.

Make :– New Age / Omex/ Getech / Safe Fire

Providing ,fixing testing and commissioning of Flexible rubber Bellows double flanged as below.

150 mm dia

100 mm dia

Providing & fixing carbon steel Fire man axe with rubber insulated handle tested to 20000 volts.

Make – New Age /Omex/ G Tech / Safe Fire

Providing and fixing Carbon-di-oxide Fire Extinguishers consisting of welded M.S cylindrical body, squeeze lever discharge valve fitted with internal discharge tube. 30cms long high pressure discharge hose. Discharge nozzle,suspension bracket, confirming to IS:934 finished externally with red enamel paint and fixed to wall with brackets with rawl plug/dash fasteners complete with internal charge. (CCOE Nagpur Approved clynders)

Capacity 4.5 Kg.

Make :– Life guard /Omex/ Getech / Safex / Safe Fire

Providing and fixing of ABC type (Stored Pressure) Fire Extinguisher I.S.I marked & T.A.C.approved complete in all respect.

4 kg. capacity

Make :– Life guard / Omex/ Getech / Safex / Safe Fire

Supply & fixing of 6 Nos. G.I Round Bottom Fire Buckets of 9.5 liters capacity filled with sand including proper supporting arrangement in MS angle iron frame,painted by fire red colour over two coats of red oxide paint and wrtten with white paint "FIRE" complete in all respect.

Providing and Fixing of self illuminated /auto glow Exit signs printed on photoluminescent sheet containing self illuminated base chemical,of appropriate size not less than 400x150mm,suspended from ceilling or fixed to the walls with accessories as riquired and as directed at site.

Make :– Mr. Lite / Lee Grand / ISI

Providing & fixing PRESSURE GAUGE 100 mm dia including making connection with m.s pipe complete in all respect.

Make :– Indfoss / ISI

Providing & fixing PRESSURE SWITCH 100 mm dia including making connection with m.s pipe complete in all respect.

Make :– H Guru / ISI

Supplying,Installatoin,Testing,& Commissioning of electric driven Hydrant Pump suitable for automatic operation consisting of the following complete in all respects as required.Horizontal type,multi stage,centrifugal,split casing pump of cast iron body & bronze impeller with stainless steel shaft,mechanical seal to ensure a minimum pressure of 3.5 kg/sq.cm at highest and farthest oulet at specified flow of 2280 LPM at 70 M head conforming to IS:152 Suitable HP Squirrel cage induction motor,TEFC synchronous speed1 RPM,suitable for operation on 415 V3 phase 50 Hz,AC with IP 55 protection for enclosure,horizontal foot mounted type with class F insulation,conforming to IS:325.Pump set shall be assembled at works and tested to satisfy performance requirements.MS fabricated Common base plate,coupling,coupling guard,found bolts etc as require Suitable cement concrete pump foundation duly plastered with anti vibration pads.

Make :– Kirloskar / Mather & Platt / ABB / CGL / Greaves

Supplying,installation,testing,& commissioning of diesel engine driven Horizontal type,multi stage,centrifugal pump of cast iron body and bronze impeller with stainless steel shaft,mechanical seal to ensure a minimum pressure of 3.5 kg/sq. cm at highest and fartest outlet at specifiedflow of 2280 LPM at 70 M Head conforming to IS:1520 Suitable hp,2000 RPM water cooled with radiator, diesel engine conforming to relevant BS & IS standarde complete with auto starting mechanism,12 volts/24 volts electric starting equipment,Diesel Tank,exhaust pipe extended to1.0 Moutside pump house duly insulated with 50 mm thick glass wool with1.0 mm thick aluminium sheet cladding,residential silencer, instruments and protection as per satisfy performance requirements. MS fabricated specification,stop solenoid for auto stop in the event of fault with audio indications,apinted with post office red colour etc as required.Pump set shall be assembled at works and tested to Common base plate,coupling,coupling guard,foundation bolts etc as required.Suitable cement concrete pump foundation duly plas - tered with anti vibration pads.

Make :– Kirloskar / Mather & Platt / ABB / CGL / Greaves

Supplying,Installatoin,Testing,& Commissioning of electric driven Pressurisation Pump suitable for automatic operation consisting of the following complete in all respects as required.Horizontal type, multi stage,centrifugal,split casing pump of cast iron body & bronze impeller with stainless steel shaft,mechanical seal and flow of 180 LPM at 70 M head conforming to IS:1520.Suitable HP Squirrel cage induction motor,TEFC,synchronous speed 2900 RPM,suitable for operation on 415 V,3 phase 50 Hz,AC with IP 5 protection for enclosure,horizontal foot mounted type with class F insulation conforming to IS:325.MS fabricated Common base plate,coupling, coupling guard, foundation bolts etc as required Suitable cement concrete pump foundation duly plastered with anti vibration pads.

Make :– Kirloskar / Mather & Platt / ABB / CGL / Greaves

ELECTRICALS Fabrication and Supplying of Fire Fighting Panel of cubical construction, floor mounted type, fabricated out of 1.5mm. thick CRCA sheet, compartmentalized with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection, having switchgears and accessories mounting and internal wiring, earth terminal, numbering etc.complete in all respects, suitable for operation on 415 V, 3 phase 50 Hz. AC supply with enclosure protection class IP 52 as required.

(INCOMER & METERING)

- 200A TP 36 KA MCCB with Inbuilt thermal magnetic release

- Set of 3 Phase indicating lamp.

- Set of Al. bus bar of 400A capacity.

(OUTGOING)

(a) MAIN FIRE PUMP-1 Nos

(b) JOCKEY PUMP - 1 Nos

(c) DIESEL ENGINE CONTROL - 1 Nos.

Make :– (Component- L&T / G.E )

Supply, Installation, testing and commissioning of Cast Iron body 'Y' Strainer complte with all fitting as requied like MS flange, nut bolts,washers etc.

Make : Castle/Deepak/Kartar

Providing and fixing Foot Valve

150 mm dia

RCC Hole Cutting

Fire Alarm System Supply, installation, testing and commissioning of main fire alarm panel supply source (230AC 50 Hz and 24 V DC) 24V out put supply for detector. fault indication open, short circuit in detector line. visual indication fire, fault, open, short & system on. 4 Zone.

Supply, installation, testing and commissioning of MS body electronic sounder ( hooter ).

Supply, installation, testing and commissioning of MS body manual call point.

Supply, laying, testing and commissioning of 1.5Sq.mm PVC insulated copper conductor single core wire in the existing PVC conduit as required.

Make : Anchor / Pollycab / Great White / Equivalent

Supply, laying, testing and commissioning of 20mm PVC conduit along with accessories complete as required.

Make : Sidhbali / Kalinga / Equivalent

SUB HEAD - I SCHEDULED ITEMS WIRING Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Group C

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

4 X 4 sq. mm + 2 X 4 sq. mm earth wire

4 X 10 sq. mm + 2 X 6 sq. mm earth wire

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit asrequired.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required.

75 mm X 75 mm X 60 mm deep

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

5/6 amps switch

3 pin 5/6 amp socket outlet

Telephone socket outlet

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.

Supplying and fixing brass batten/ angle holder including connection etc. as required.

BOARD & DB'S Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

6 way (4 + 18), Double door

8 way (4 + 24), Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single pole

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 30 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 A "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts& nuts, painting suspenders etc as required.

150 mm width X 50 mm depth X 1.6 mm thickness

4.2 Supplying and installing following size of perforated painted with powder coating M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

150 mm width X 50 mm depth X 1.6 mm thickness

EARTHING Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

Fixing of lightning conductor finial (single prong) with base plate including holes etc. complete as required.

Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required.

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run)

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.

Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.

POWER WIRING FOR ALL WORKSHOP Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

100 mm width X 50 mm depth X 1.6 mm thickness

150 mm width X 50 mm depth X 1.6 mm thickness

225 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

375 mm width X 50 mm depth X 2.0 mm thickness

450 mm width X 50 mm depth X 2.0 mm thickness

600 mm width X 50 mm depth X 2.0 mm thickness

900 mm width X 75 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required.

100 mm width X 50 mm depth X 1.6 mm thickness

150 mm width X 50 mm depth X 1.6 mm thickness

225 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

375 mm width X 50 mm depth X 2.0 mm thickness

450 mm width X 50 mm depth X 2.0 mm thickness

600 mm width X 50 mm depth X 2.0 mm thickness

900 mm width X 75 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays Tee with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required.

100 mm width X 50 mm depth X 1.6 mm thickness

150 mm width X 50 mm depth X 1.6 mm thickness

225 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

375 mm width X 50 mm depth X 2.0 mm thickness

450 mm width X 50 mm depth X 2.0 mm thickness

600 mm width X 50 mm depth X 2.0 mm thickness

900 mm width X 75 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays Reducer with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required.

100 mm width X 50 mm depth X 1.6 mm thickness

150 mm width X 50 mm depth X 1.6 mm thickness

225 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

375 mm width X 50 mm depth X 2.0 mm thickness

450 mm width X 50 mm depth X 2.0 mm thickness

600 mm width X 50 mm depth X 2.0 mm thickness

900 mm width X 75 mm depth X 2.0 mm thickness

Supplying, installing, testing and commissioning of following capacity TPN tap off box made of 1.6mm thick sheet steel enclosure duly painted with powder coating on existing rising mains complete with TPN disconnector FSU and HRC fuses, connections, earthing etc. as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

3½ X 25 sq. mm (28mm)

3½ X 70 sq. mm (38mm)

3½ X 185 sq. mm (57mm)

3½ X 300 sq. mm (70mm)

4 X 10 sq. mm (25mm)

4 X 16 sq. mm (28mm)

Erection of metallic pole of following length in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required.

Above 8.0 metre and upto 10.0 metre

Supply of 100 mm dia. G.I. pipe (medium class)

Excavation of the cable trenches in hard rock not exceeding 1.5 metres in width, and lift upto 1.5 metres, including getting out the excavated soil and disposal of excavated soil as directed within a lead of 50 metres.

Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required

100 mm dia

150 mm dia

Supplying,installation,testing and commisioning of 33kV/0.433kV or 11kV/0.433 kV substation equipments comprising HT Panel, Dry type Transformers, HT cable, Bus trunking from Transformer to LT Panel, LT Panel, Automatic Power factor correction panel, Active Harmonic Filters,TVSS (Transient Voltage suppression system), SPD (Surge protection system), Essential panel,Earthing,required inter-connections, substation safety euipments including LT cabling from sub station to the buildings fed by the sub station.

SUB HEAD - II (NON SCHEDULED / EXTRA ITEMS) Supply and Installation of AC 230/250 volts, 50 HZ exhaust fans including providing nuts, bolts, mounting frame and other accessories etc. complete . Model- Ventil Air - DS (Make : Havells) 300 mm sweep 900 rpm ,complete in all aspects as per direction of Engineer in Charge.

300 mm sweep 900 rpm

Supply,Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

Supply and fixing of smart bright extruded aluminium batten available in 2ft & 4ft run length with multiple lumen packages and suitable for surface, wall & conduit mounting (Non work shop area with accessories).

Supply and fixing of smart brite xtra extruded aluminium batten for continuous operation and available in 4ft run length, suitable for surface, wall & conduit mounting (Non work shop area with accessories).

Supply and fixing of industrial battens endura LED next flicker free, high efficiency and robust industrial batten family suitable for surface, wall and conduit mounting. The product family offers dimmable and connected batten option.

Supply and fixing of Dura LED Highbay IP66 & IK08 protected LED Highbay solution with PDC housing, toughened & shattered proof glass available in both narrow & wide beam optics.

SUPPLY OF LED Glass Bulb B22, 15 W ,6000k /4000k/3000K ,230/250 Volt,50 HZ ETC, complete in all aspects as per direction of Engineer in Charge.

MAIN DISTRIBUTION BOARD Supplying, fixing, testing & commissioning of 415V ,3Phase 50Hz, 4wire system,sheet steel clad,dust & vermin proof cubical & indoor type floor mounted, free standing Main Distribution Board with IP - 42 protection, compartmentalized design and fabricated out of 2mm/1.6mm CRCA sheet steel complete with aluminium Bus Bars, Providing & Fixing of base plate /channel, P/F the following Switchgears,complete with earth Bus Bar throughout the length of the panel,terminal arrangement for incomings/outgoings cables and also outgoing terminations for various sizes of cables,the incoming and outgoing feeders shall be accommodated in a modular multi-tier arrangement,adequate size bus duct/cable alley, Sign writing, Painting, Earthing, Numbering, Danger plate etc. Compleete as requried,numbering, danger plate etc. complete as required as per specification and drawing with pannel stand.

INCOMER: 1 nos. 100A 415V, Ics=25KA, 4P MCCB with TM release having O/L, S/C E/F,O/V & U/V protection.

1 nos. Digital type multi function meters (V+A+Hz) with cast resin CTs 200/5A.

1 Set of phase indicating lamp with MCB

BUSBAR

150A TPN Bus bar of aluminimum alloy.

OUTGOING

3 nos. 16/63A, 415V, 4P MCB of 10kA.with O/L and S/C protection.(Light workshop sub pannel PTTA Pannel)

Supply and Fixing of sub panel of Incoming 125 Amp. MCCB-01 No & Outgoing of 10 Nos 32/16 Amp TPMCB with pannel stand complete with all respect.(Heavy workshop sub pannel PTTA Pannel)

SITC of main panel made of CRCA sheet dust and vermin proof with incommer of 250 amps verable type FPMCCB and outgoing of 125 amps verable type FPMCCB-04 No. & 30 to 40 amps verable type FPMCB 08 No. include & phase indicating lamp voltmeter, ampermeter with pannel stand complete in all respect. (Workshop main pannel PTTA Pannel)

SITC of main panel made of CRCA sheet dust and vermin proof with incommer of 630 amps verable type FPMCCB and outgoing of 400 amps verable type FPMCCB-01 No. & 250 amps verable type FPMCCB 01 No. 05 to 32 amps FPMCB 15 No.include, 630 amp change over switch & phase indicating lamp voltmeter, ampermeter, change over switch with pannel stand complete in all respect.(Main Building Pannel TTA Pannel).

LT XLPE CABLES Supply,of following sizes of PVC sheathed LT XLPE armoured, aluminium 1.1KV grade, as required of the following sizes.Rates should be taken W.E.F 01.12.2018 KEI

4c x 10 sq.mm cable

4 c x 16 sq.mm

3.5 c x 25 sq.mm

3.5 c x 70 sq.mm

3.5 c x 185 sq.mm

3.5 c x 300 sq.mm

Networking

Supplying and drawing of LSZH UTP 4 pair CAT 6 LAN cable in the existing surface/recessed steel PVC conduit as required 4 Pair cat 6 unshielded blue colour conforming to the following standard like ISO/IEC 11801 amendment 2:2010 class EA, TIA/EIA-568-c2 category 6, IEC 61156-5 ETL independent testing, ES50288-6-1 standard cable with 23AWG approved make list Molex, Panduit, Siemon.

SITC of Cat-6 information outlet should be 360 degree shielded metal housing following TIA-568-C 2 augmented cat6 ISO 11801 amd 1 class EA, IEC 60603-7 FCC subpart F 68.5 approved make list Molex, Panduit, Siemon.

SITC of 24 port Cat 6 patch pannel available with block of four equipped with IO rack mountable 19 modular patch pannel loaded cat 6 UTP 24 port LCS2 rack mountable to be compatible in 4 nos of 6 x RJ 45 connector UTP unit in a block. Approved make list Molex, Panduit, Siemon.

SITC of 4 feet Cat-6 UTP 23 AWG patch cord -1 mtr rack end factory crimped patch cord in blue colour. Approved make list Molex, Panduit, Siemon.

SITC of 7 feet Cat-6 UTP 23 AWG patch cord -1 mtr rack end factory crimped patch cord in blue colour. Approved make list Molex, Panduit, Siemon.

SITC of 1, 2 and 4 port face plate white for I/O fixing at user side for data, voice approved make list Molex, Panduit, Siemon.

SITC of 15 u wall mount rack with fans, 2 cable managers, satationary shelf, 2 nos of hardware pkts. Approved make list APW, Rittal, Deliyod.

Supply and Installation of rubber insulation mate size 2 x 2 mtr.

M/S Shiv Kumar Agarwal

Sunehari Bagh Builders Pvt. Ltd.

ABHILASHA ENTERPRISES