Renovation cum Refurbishment works in CSIR-NIIST Staff Quarters (Type-II, Type-III)

Amount

CIVIL WORKS - EXTERIOR PAINTING (For Two Blocks)

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. - With cement mortar 1:4 (1 cement : 4 fine sand)

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

Finishing walls with Acrylic Smooth exterior paint of required shade: New work (Two or more coat applied @1.67 ltr/10 sqm over and including priming coat of exterior primer applied @0.90 litre/10 sqm

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work

CONVERSION OF IWC TO EWC (For 8 Flats)

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. - Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry

15 mm cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement on the rough side of single or half brick wall

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.

Providing and fixing soil, waste and vent pipe - PVC Pipes with suitable fittings. This includes jointing of pipes & fittings with one-step CPVC solvent cement and testing of jointing complete as per direction of the Engineer-in-charge. - Both internal & External works - 100mm dia pipes (6kg/sq.cm)

WATER SUPPLY (For 8 Flats)

Providing and fixing rectangular high density polyethylene water storage loft tank with cover, conforming to ISI : 12701, colour of opaque white or as approved by Engineer-in-charge. The rate includes making necessary holes for inlet, outlet & over flow pipes. The base support i/c fittings & fixtures for tank shall be paid separately

Supplying the following items of the approved make & model etc complete as per the approval of Engineer-in-charge - to the NIIST ESD storE

1" Brass lever valve

C.P.Brass 15mm Long body Tap (Heavy)

C.P.Brass 15mm short body tap (medium)

C.P.Brass Wash basin tap (heavy)

C.P.brass Stop cock

C.P.brass 15mm Angle cock

1.25" CP waste (full threaded)

1.25" CP waste (with overflow)

1.25" PVC waste

15mm C.P.brass Heakth faucet set (Heavy)

C.P.Brass 15mm two way tap

Shower rose C.P.brass for 15 to 20mm inlet 150mm dia

Kitchen sink CP waste

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (External work)

20mm nominal dia pipes

25mm nominal dia pipes

32mm nominal dia pipes

40mm nominal dia pipes

50mm nominal dia pipes

FURNISHING WORKS - (8 Flats)

WARDROBE - Supplying and fixing a box-type wardrobe by using 12mmm thick marine plywood and finished with 0.8mm decorative lamination on the exposed surface and normal lamination on the inner surface. Hot pressed edge band finishing on all edges. Cost including one number of Aluminium hanger rods, Locking arrangements, handles and auto hinges etc as per the direction of Engineer-in-charge

ELECTRICAL WORKS - DISTRIBUTION BOARDS

Supplying, installing, testing, and commissioning of compartmentalized meter switchboard made of 16 SWG MS sheet steel to accommodate 4 Nos energy meter, duly powder coated in approved colour including connections, interconnections, earthing, etc. complete as required. Incomer- 100A, 16kA, 4 pole MCCB, Outgoing- 32A HRC fuse unit with 32A 2 pole isolator

Supplying and fixing 5A to 32A rating, 240/415V, 10KA, « c » curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections , testing and commissioning etc. as required

Single pole – 10A

Single pole – 16A

Single pole – 25A

Supplying and fixing following rating, double pole, ( single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commisioning etc. as required. 25A

Supplying and fixing suitable GI box with modular plate and cover in front on surface including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, etc. as requireD

WIRING FOR LIGHT/FAN/PLUG SOCKETS, ETC

Wiring for circuit/submain wiring alongwith earth wire with the following sizes of FLRS PVC insulated copper conductor , single core cable in surface / recessed medium class PVC conduit as required. 2 X 4 sq.mm + 1 X 4 sq.mm earth wire

Supplying and drawing following size of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 3X4 sq.mm

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required

Supplying of 300/305 mm sweep Light Duty Exhaust fan in metal frame working on 230 V 50HZ AC

Installation of exhaust fan in the existing opening, including making good the damage, testing, commisioning etc. as required. Upto 450mm sweep

CIVIL WORKS - EXTERIOR PAINTING (For Two Blocks)

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. - With cement mortar 1:4 (1 cement : 4 fine sand)

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

Finishing walls with Acrylic Smooth exterior paint of required shade: New work (Two or more coat applied @1.67 ltr/10 sqm over and including priming coat of exterior primer applied @0.90 litre/10 sqm

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work

CONVERSION OF IWC TO EWC (For 8 Flats)

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. - Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry

15 mm cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement on the rough side of single or half brick wall

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete

Providing and fixing soil, waste and vent pipe - PVC Pipes with suitable fittings. This includes jointing of pipes & fittings with one-step CPVC solvent cement and testing of jointing complete as per direction of the Engineer-in-charge. - Both internal & External works - 100mm dia pipes (6kg/sq.cm)

WATER SUPPLY (For 8 Flats)

Providing and fixing rectangular high density polyethylene water storage loft tank with cover, conforming to ISI : 12701, colour of opaque white or as approved by Engineer-in-charge. The rate includes making necessary holes for inlet, outlet & over flow pipes. The base support i/c fittings & fixtures for tank shall be paid separately.

Supplying the following items of the approved make & model etc complete as per the approval of Engineer-in-charge - to the NIIST ESD store

1" Brass lever valve

C.P.Brass 15mm Long body Tap (Heavy)

C.P.Brass 15mm short body tap (medium)

C.P.Brass Wash basin tap (heavy)

C.P.brass Stop cock

C.P.brass 15mm Angle cock

1.25" CP waste (full threaded)

1.25" CP waste (with overflow)

1.25" PVC waste

15mm C.P.brass Heakth faucet set (Heavy)

C.P.Brass 15mm two way tap

Shower rose C.P.brass for 15 to 20mm inlet 150mm dia

Kitchen sink CP waste

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (External work)

20mm nominal dia pipes

25mm nominal dia pipes

32mm nominal dia pipes

40mm nominal dia pipes

50mm nominal dia pipes

FURNISHING WORKS - (8 Flats)

WARDROBE - Supplying and fixing a box-type wardrobe by using 12mmm thick marine plywood and finished with 0.8mm decorative lamination on the exposed surface and normal lamination on the inner surface. Hot pressed edge band finishing on all edges. Cost including one number of Aluminium hanger rods, Locking arrangements, handles and auto hinges etc as per the direction of Engineer-in-charge.

INTERIOR PAINTING (For 8 Flats)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with 1st quality acrylic distemper (ready mixed) having VOC(Volatile Organic Compound) content less than 50 gram/litre, of approved brand and manufacturer including applying additional coats wherever required to achieve even shade and colour. (Old work (one or more coats)

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour: New work two or more coats over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre

FLOORING (For 8 Flats)

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade,Fixing glazed/ Ceramic/ Vitrified floor tiles with cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477, in atleast 3mm thickness, jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. - Double charged vitrified tile polished finish of Size of Tile 600x1200 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joint with white cement & matching pigments etc. complete. - Size of Tile 600x1200 mm

Dismantling tile work in floors, Walls and roofs laid in cement mortar including stacking material within 50 metres lead. - For thickness of tiles 10 mm to 25 mm

Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge.

ELECTRICAL WORKS - DISTRIBUTION BOARDS

Supplying, installing, testing, and commissioning of compartmentalized meter switchboard made of 16 SWG MS sheet steel to accommodate 4 Nos energy meter, duly powder coated in approved colour including connections, interconnections, earthing, etc. complete as required. Incomer- 100A, 16kA, 4 pole MCCB, Outgoing- 32A HRC fuse unit with 32A 2 pole isolator

Supplying and fixing 5A to 32A rating, 240/415V, 10KA, « c » curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single pole – 10A

Single pole – 16A

Single pole – 25A

Supplying and fixing following rating, double pole, ( single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commisioning etc. as required. 25A

Supplying and fixing suitable GI box with modular plate and cover in front on surface including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, etc. as required

WIRING FOR LIGHT/FAN/PLUG SOCKETS, ETC

Wiring for circuit/submain wiring alongwith earth wire with the following sizes of FLRS PVC insulated copper conductor , single core cable in surface / recessed medium class PVC conduit as required. 2 X 4 sq.mm + 1 X 4 sq.mm earth wire

Supplying and fixing the following size/ modules, GI box along with modular base with cover plate for modular switches in recess etc. as required. 6 Module (200mmX75mm)

Supplying and fixing the following size/ modules, GI box along with modular base with cover plate for modular switches in recess etc. as required. 12 Module (200mmX150mm)

Supplying and fixing of following modular switch/socket on the existing modular plate and switch box including connections but excluding modular plate etc, as required.

5/6 A switch

2 way 5/6A switch

15/16 A switch

3 pin 5/6 A socket outlet

6 pin 15/16 A socket outlet

LIGHT FIXTURES

Supply 1x20 W LED box type tube fittings. The fittings shall be made from CRCA MS sheet of minimum thickness 0.50 mm nominal thickness inside & outside (including LED Tube).

Installation, testing, commisioning of wall bracket/ ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting, complete with all accessories including connections etc. as required.

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Supplying of 300/305 mm sweep Light Duty Exhaust fan in metal frame working on 230 V 50HZ AC.

Installation of exhaust fan in the existing opening, including making good the damage, testing, commisioning etc. as required. Upto 450mm sweep

PINKATRON SECURITIES PVT LTD (BID ID -861487)